At first heating season- it's time to think about how to prepare plastic windows for winter. To complete the work you will need a Phillips screwdriver and a hex key.

First of all, wash the windows, profile, window sills and slopes. We recommend using small amounts of non-aggressive detergents and a soft sponge. For achievement best result can be opened window sash and use a sharp object to remove dirt that has accumulated in the drainage channels. For these purposes, you can use a toothpick or match. Clean drains will freely drain excess water and prevent ice from forming in these places.

In the cold season, the seal should be additionally protected with technical Vaseline or silicone grease. The sealant is coated with the product around the entire perimeter. This approach will protect the material from freezing and drying out.

In order to ensure smooth operation of the mechanism, the moving parts of the window unit should also be lubricated with Vaseline or a silicone-based compound. Dust does not stick to silicone, which allows you to keep your windows clean.

If you see it on sale special sets for the care of seals and fittings, do not pass by, be sure to purchase. Manufacturers recommend performing this treatment twice a year.

A loose window handle is one of the common problems plastic windows. In order to return it to its original state, turn the handle to the “open” position (so that it is parallel to the window sill), then turn the handle cover located at its base by 90 degrees. Under the trim you will find two screws that need to be tightened with a Phillips screwdriver.

Next stage preparing plastic windows for winter - checking the tightness of the sash. For such an experiment, you will need a regular piece of paper, which you need to insert into the flap of the sash, and then close it. If the leaf is removed with some effort, then everything is in order with the density. If the paper is removed from under the seal without any hindrance, then it’s time to adjust the window fittings to " winter mode".

Setting up is quite easy. To do this, open the sash; on the end part you will see roller bushings. U different manufacturers bushings may have different kind, but in production the middle position is always set. You need to insert a hex key into this sleeve and turn it so as to ensure maximum pressure. In this way, the fittings are adjusted to suit the required season. After this, all that remains is to close the sash. The increased force on the handle will indicate that all actions were performed correctly. The sash will close tighter. The next fitting adjustment should be made with the onset of spring. This approach will avoid premature wear of the seal.

As you can see, there is nothing complicated in preparing plastic windows for winter. For further defect-free operation of window systems, it is important to maintain normal air humidity (no more than 45-50%) and ensure correct work exhaust and supply ventilation. You can check their effectiveness using the same piece of paper. To do this, bring it one by one to everyone ventilation holes. More accurate data can be obtained by using an anemometer. Do not forget that windows should not be perfectly sealed, as this leads to the formation excess moisture in the air. Arrange airing sessions for the apartment at least 2-3 times a day.

Thanks to plastic windows, homes have become more comfortable and cozy. Winter has ceased to be a terrible enemy. Distinctive features PVC windows are characterized by their strength, reliability and long service life. But these products also require periodic repairs.

So that windows can protect you in winter time, maintaining heat, it is necessary to produce preliminary preparation. Thanks to such work, the windows will function normally. Preparing windows for winter includes a number of activities. How to switch windows to winter mode? How to prepare plastic windows for winter?

Let us consider in detail the following algorithm of actions:

• First, you just need to wash the windows and do it thoroughly. It is necessary to wash the slopes, the window sill, and the profiles, especially if they are made of plastic material. Do not use aggressive cleaning agents for cleaning. chemicals. Glass needs a rag and a soft sponge to clean. Windows should be washed on both sides: internal and external. When opening PVC windows, pay attention to the channels intended for drainage; they also need to be cleaned. This can be done using a toothpick or other sharp instrument or object.
• Pay attention to the moving components of the window hardware. Pressure rollers - this is where the largest cluster mud. Dirt is the main obstacle to the normal functioning of these elements. To clean, use a brush that has hard bristles - this will help get rid of dust and old grease.
• Once cleaning of windows and areas that are difficult to reach is completed, it is necessary to lubricate the mechanisms. For this you will need silicone lubricant. Buy lubricant foreign manufacturer, since it has a long service life. If you don't want to spend your money on it cash, then you can use solid oil. According to many, ordinary oil can be used as a lubricant. vegetable oil. But this is far from true. After a certain period of time, the vegetable oil dries out and becomes a kind of “sandpaper” that can make the mechanisms unsuitable for functioning. This may happen after about a year. When you lubricate the pinch rollers, be sure to turn the handle at this moment. Thanks to this, the lubricant can be evenly distributed throughout all parts.
• Next, check the condition of the seals. This procedure must be taken seriously, because seals affect general meaning temperature in the house. If strange noisy sounds appear inside the room, and the windows sweat, then these signs indicate a damaged seal. To increase the service life of the seal, it is necessary to clean and lubricate it occasionally. Use imported silicone as a lubricant. Lubricate the entire length of the seal to prevent freezing and drying out. If you notice wear and tear, you need to replace the product. It is possible to do this yourself. Before purchasing, be sure to pay attention to the shape of the planting area because it may vary. The sealing element must be removed using a flat screwdriver and install the new product. To make the job easier, lubricate the planting area. Once the work is completed and the sealing thing is set, it is necessary to carry out a generous treatment of the sealant, from its upper part.

Follow these four steps when cleaning out accumulated dirt. This is the first step to prepare the windows.

Adjusting the window for winter

As soon as winter approaches, it is necessary to carry out window adjustments. This will help switch them to winter mode. The procedure is that the frame must be pressed tightly against the window to prevent the penetration of drafts. For this job you will need a hex wrench.

The sides, which are positioned horizontally, are adjusted from top to bottom across the panels. To carry out such adjustment, there are sockets in the window hinges intended for a hex key.

To adjust the top panel, the window must be open. To lift the edge of the panel, which is located opposite the hinge, the tool must rotate in right side. To lower, rotate the tool in the opposite direction.

If the plastic window is located low, but you can control it from the street side, then you do not need to open the sashes to adjust it. Therefore, you will be able to make an offset of two millimeters. Or eliminate the bevel, also by two millimeters.

The loop located at the bottom allows you to adjust the vertical sides. To gain access to the hex socket, you must remove the safety cap. Also, to raise the tool, twist it to the right, and to lower it, turn it in the opposite direction. The shift value is two millimeters.

When changing the pressing force along the vertical and horizontal parts, do not forget that the eccentrics responsible for this are located throughout the edging. When turning the handle, each eccentric moves beyond its clamping point.

To increase the frame pressing force, the eccentric must turn to the right. To reduce the force, it must turn in the other direction. Each eccentric has specially designed marks. Thanks to them, you can determine the pressing force of the frame. Therefore, if the mark is located where the seal is, this means that the pressure is strong. If the mark is turned where the street is, then the clamp is weak.

Some windows have eccentrics that can be turned using ordinary pliers.

In the places where the hinges are located, there are devices that regulate the clamping force. The degree of force is determined by the protrusion of the tongue. The length of the tongue determines the tightness of the frame against the window. Changing the length of the tongue is done using a hex key.

To increase the length of the tongue, the tool must be turned to the left if the loops are located on the left side. If the loops are located on the right, then you need to twist it to the right. During the winter period it is necessary to press the frame as hard as possible. IN summer period the pressure should be weak.

The main thing is not to overdo it. Do not press the frame too hard, otherwise the sealing material will wear out faster.

Also, in preparation for the winter season, the hinges also need to be adjusted, that is, pressed firmly. From the hinge located below, you need to remove the specially designed cap and turn the bolt located perpendicularly.

You can adjust the pressing force of the hinge, which is located on top, if there is a flap. Its installation is carried out for ventilation, thus you can use a key. During this work, hold the window, because it is fixed using a single hinge.

The procedure for insulating plastic windows

If after some certain period after PVC installations Since the windows begin to let in drafts and do not retain heat, it is necessary to insulate them. But first you need to find out the reasons for these problems. Let's look at the main reasons:

• The rubber seal has worn out. A replacement needs to be made.
• The area where the frame and slope meet is depressurized. For liquidation this deficiency, the slopes should be removed, insulated and reinstalled. We close the windows.
• It is possible that after you installed plastic windows, shrinkage of the walls may have occurred. To eliminate this problem, additional adjustment of the fittings is necessary.

On winter days, plastic windows can be insulated using film. This method is expensive, but at the same time the most effective. The film is applied from the street side. In rare cases, thermal insulation is carried out with inside. The film must be stretched over the entire surface of the frame and must be attached along the edges.

During this process material tension, force and uniformity must be controlled simultaneously. If the material is poorly tensioned in any place, strong wind may form a breakthrough. If it works, then the hole should be sealed with tape so as not to waste money on purchasing a new product.

When choosing a film material, you need to pay attention to frost-resistant characteristics. Required material has a yellowish tint. High-quality film is hard to find on construction market, so buy it at a large construction market. So as not to spoil appearance premises, buy material that is intended for greenhouses. This product has a higher cost, but it will last a long period of time due to its high level sustainability.

Installation of this film consists of attaching it to the edges of the frame using tape. The windows need to be closed.

Instead of tape, you can use a construction stapler, but defects will appear on the frame. The main processes of thermal insulation and sound insulation are provided by double-glazed windows.

There is PVC insulation that can replace film. This insulation is environmentally friendly pure material. Manufacturers guarantee high-quality thermal insulation. PVC insulation can withstand low temperature and is not subject to deformation. You need to decide for yourself which material to choose.

When you winterize your windows, pay attention to these tips. Preparing plastic windows for the winter with your own hands is a guarantee of maximum comfort and coziness in the room. The entire premises will be switched to winter mode. Carry out the work carefully and carefully.

Don't skimp on thermal insulation materials. Don't forget to clean the surface before starting the procedure. You will be able to switch the windows to winter mode. Prepared plastic windows for the winter will not allow cold into the room.

Evgeniy Sedov

When your hands grow from the right place, life is more fun :)

Content

Plastic window designs Different companies have similar adjustments. When installing them, the average pressure density values ​​are set. Over time, due to wear or other factors, the sash may sag and begin to catch on the frame or impost. When the temperature drops cold air from the street can begin to penetrate into the room. In all these cases, it is necessary to adjust the windows, which you can do yourself if you know how to adjust plastic windows for the winter by switching the pressure settings from summer to winter.

What tools are needed to adjust a plastic window?

Plastic window systems have become the most popular product that is installed during the construction or renovation of both a simple apartment and a luxurious multi-story mansion. With all the variety of window fittings used in their creation, all systems use similar mechanisms. Preparing plastic windows for winter begins with the first cold snap. The main tools you may need to adjust windows are:

• hexagonal L-shaped key 4 mm wide;
• flat screwdriver 4 mm;
• Phillips screwdriver;
• pliers.

How to set windows to winter mode

In order to prepare Euro-windows for winter period, seasonal adjustment of the pressure of plastic windows is necessary, in which the following actions must be carried out:

1. Adjust the opening sash vertically and horizontally - it should not cling to the frame and clamping strips.
2. Adjust the clamping force to the frame. The pressure is adjusted using adjustable trunnions or eccentrics, the number of which on euro-windows is 4-5 pcs., on doors - 6-8 pcs.
3. If there is traction at maximum pressure to the frame, it is necessary to replace the seal. Then check the traction at the middle position of the trunnions or eccentrics.

The clamping to the frame is based on the engagement of the rounded elements of the sash by the clamping strips when the handle is turned down. These round elements, made in the form of an oval, are called trunnions, and those made in the form of a round element with a displaced axis of rotation are called eccentrics. The trunnions are rotated using pliers. Their installation vertically creates minimal pressure, which means summer mode pressing, horizontally – the strongest possible pressing. By rotating the eccentric with an adjusting hexagon, you can adjust the pressure from weak to stronger and back.

You can determine the need to replace the rubber seal by inspecting and checking the traction. You can change it in parts - and you save money. When you go shopping for a sealant, you should take a sample with you and buy a longer piece. It is better to trim off the excess when sticking than to leave a gap. Buy a seal made of high-quality rubber. You will need to buy special glue for it. Before inserting the seal into the groove, apply glue over the entire area of ​​contact with the seal, glue it, close the euro window while the glue dries.

Window adjustments and adjustments are made in case of large gaps or when it clings to the frame. It is necessary to adjust the opening sash vertically and horizontally in the following cases:

• if she catches top part frames - open the sash and use the short side of the L-shaped key to slightly push it out on the upper canopy;
• if, due to sagging, the sash catches the lower part of the frame, the same must be done with the lower canopy;
• if it clings to the vertical part of the frame or the impost (the middle vertical part of the frame), you need to use the short side of the L-shaped key to slightly push it on both canopies in the direction opposite to the point of such contact.

How to adjust plastic windows yourself

Windows can be adjusted independently if available. the necessary tool. The only parts that can break and require replacement are the handle and rubber seal. By adjusting the window pressure, the switch is switched to winter mode. In this case, the handle turns with force, the sash is strongly pressed against the frame, and the seal is strongly compressed. In the spring, it will be necessary to loosen the clamp, since opening for ventilation occurs frequently, which can lead to severe wear of the closing mechanism and seal.

To switch to winter mode, you must take the following steps:

1. Check for inward or outward draft around the perimeter with a lit match - even a slight breeze will deflect the flame.
2. If there is draft, it is necessary to open the sash and adjust the locking pins (eccentrics).
3. Trunnions come in 3 types - oval, round with a slot for a screwdriver or a hexagon.
4. If the oval trunnions are located vertically and the eccentrics are shifted towards the frame, it is necessary appropriate tool turn them to the middle position to increase the clamping force.
5. Then you need to check the traction again; if it remains, switch the trunnions (eccentrics) to winter mode. To do this, you need to rotate the oval trunnions to a horizontal position, and move the eccentrics completely away from the street.
6. If after checking the draft remains, you need to replace the seal.
7. After replacing the seal, check the traction when adjusting the trunnions or eccentrics in the middle position.

How to tighten hinges on plastic windows

The top hinge is adjusted using an L-shaped hexagon. On the top hinge there is one adjustment for the horizontal displacement of the top bar. The displacement control process is carried out at open window the short side of the hexagon in the adjustment hole, which is located at the end of the sash. The range of displacement of the upper part is from -2 to +3 mm. Use a wrench to turn the screw part turn and check for ease of closing.

Adjustment bottom loop made with the same tool. The difference is that on the lower hinge, in addition to shifting the bottom bar horizontally, there is a screw for shifting the entire sash vertically. Horizontal displacement is carried out in a manner similar to that for the top hinge. Vertical offset is carried out with the window half-open, for which you need to insert long side hexagon vertically from top to bottom into the canopy hole with the decorative casing removed. Such a change is possible within the range from -2 to +2 mm.

Setting up plastic windows when shrinking a house

Strong displacement of carriers building elements as a result of shrinkage of the new building, it can cause the sash to move away from the frame, requiring reinstallation of the plastic window. If the opening is severely skewed, you will have to straighten it or order a new Euro-window. By internal adjustments of the opening and clamping mechanisms, you can correct the horizontal or vertical displacement within 2-3 mm. To do this you will need a standard set of tools:

• special hex key 4 mm wide;
• screwdriver 4 mm;
• pliers.

How to set the horizontal and vertical axes

To align the sash horizontally or vertically, it is necessary to adjust the plastic window in the awnings. Alignment in the horizontal plane is made by end adjustments on the upper and lower canopy with the window fully open. The hex key is inserted with the short side into the hole. When the key is rotated clockwise, the sash is attracted to the canopy, counterclockwise - to the impost. The maximum adjustment range is -2 to +2 mm.

You can adjust the displacement in the vertical position on the lower canopy in cases where the sash touches the frame or to change the size of the gaps. To do this you will need a hex wrench. You need to open the cap on the canopy, insert the hex key with the long end down into the top hole. By rotating the bolt clockwise, the sash can be raised, and counterclockwise, it can be lowered. The maximum height adjustment range is -2 to +2 mm.

What to do if the plastic window does not close

A sash adjusted to fit the gaps at the top, bottom and sides may not close in two cases. The first is associated with a broken handle, the second with the incorrect operation of one of the pin-clamp pairs. To check, you need to open the window and, pressing the double opening latch with your left hand, turn the handle down. If it has turned to the extreme position, then there is a closing problem in one of the trunnion-clamp pairs. You can determine which pair is not working one by one by unscrewing the clamping bars with a Phillips screwdriver.

?

How to adjust the handle on a plastic window

The design, diagrams and photos of the location of fittings, adjusting bolts, moving parts of the Euro-window, troubleshooting methods and prices can be found on the Internet on sites on this topic. Adjusting the handle involves installing it correctly in accordance with the list below. The opening handle has four positions:

• down – closed;
• to the side - open;
• up – ventilation mode;
• in the middle position between the top and side – partial ventilation.

Replacing a faulty one

If your handle is broken, you must:

• Use a screwdriver to unscrew the upper and lower fastening screws (or screws) located perpendicular to the plane of the sash;
• insert a new handle in the same position in which the faulty one was removed;
• fasten it with two screws (or screws);
• return the protective plate to its original position.

If the handle on a window or balcony becomes loose, you must:

• slightly pull the top and bottom of the protective plate on the handle and turn it to a horizontal position;
• Using a screwdriver, screw the handle tightly;
• return the protective plate to its original position.

All elements of the canopy and closing of the sash are located outside the structure. The main actions when the elements of this mechanism become dirty are cleaning and lubrication. If the window has not been opened for a long time, dried dirt or rust can be removed using a can of universal penetrating lubricant VD-40. After cleaning and washing, you need to lubricate the fittings and adjust them.

The eccentrics are round elements that engage the clamping bars. The axis of their fastening is shifted relative to the center of the circle, so when rotating, the distance from the axis to the point of contact with the pressure bar changes. As this distance increases, the pressure of the sash against the frame increases. The eccentrics are rotated using a hex key or screwdriver. The amount of pressure change varies from 2 to 5 mm, depending on the design of the eccentric. It is necessary to adjust the clamping force twice a year when switching from summer to winter mode and back.

What to do if the window handle is jammed

Among possible breakdowns the locking mechanism may jam the handle. There is no need to apply great force to the handle to open it - the fittings should be taken care of to extend their service life. Jamming is possible in three situations - the window is open for ventilation, wide open or closed. If the handle jams in the first two cases, a distortion during opening or a special lock may be triggered. If the sash hangs on one bottom hinge, the following operations must be performed:

• turn the handle up;
• pressing the top hinge to the frame, set the handle to the right;
• close the window and turn the handle down;
• Pressing the sash against the frame, carefully turn the handle up and open for ventilation.

The rotation lock can be activated as a result of a sharp turn of the handle at a large angle when opening. The lock is released by pressing the unlocking button or turning the corresponding lever. Its location can be found on the website of the company that developed your hardware. If you have difficulty opening, try pressing the sash firmly against the frame and turning the handle.

Stiffness in turning or jamming of the handle when closed window possible with shrinkage and strong (more than 2-3 mm) subsidence of a window or doorway. This is an extremely rare and complex case that can lead to frame bevel or mechanism failure. Without specialists construction company or installers solve this problem simple adjustments it won't work. Jamming is possible due to lack of lubrication of the bolt mechanism. To prevent this and increase service life Maintenance It is advisable to do it once or twice a year.

How much does it cost to adjust Euro windows in Moscow?

Repair and adjustment of plastic windows is carried out by many companies in Moscow, St. Petersburg, and other cities of Russia, which know how to adjust PVC windows and can supply new spare parts. Prices for such services vary by region of the country; they depend on the brand of the hardware manufacturer. A visit by a specialist for a technical inspection and drawing up an estimate in Moscow will cost from 500 to 1000 rubles. The minimum order cost in Moscow is from 2000 to 3000 rubles. The cost of main work is indicated in the table:

Name	Unit	Cost, rubles
Setting up fittings (without removing)
Door adjustment (without removal)
Adjustment, repair, partial overhaul of the mechanism (without replacing fittings)
Adjustment, repair, partial overhaul of door hardware (without replacement)
Reinstalling the glass unit during adjustment
Reinstallation of the double-glazed door (the price of the double-glazed window is not included)
Cleaning and lubrication of accessories
Replacing the seal (the price of the seal is not included)
Replacement complete set rotary fittings
Handle white/colored Found an error in the text? Select it, press Ctrl + Enter and we will fix everything!

The Russian climate is characterized by sharp temperature changes in the cold and warm seasons. The difference between summer highs and winter lows is tens of degrees. Plastic windows can be used at temperatures from −40 °C to 60 °C, so residents of most regions of our country do not have to worry about the ability of the window to withstand winter frost or summer heat. However, consumers must properly care for their windows to ensure they effectively protect the room from too low or too high temperatures.

Having prepared your window for winter, you can enjoy
comfort and warmth

Why prepare your window for winter?

Plastic windows require maintenance regardless of the time of year. For example, keeping windows clean is not just a matter of aesthetics and hygiene. By promptly removing dirt from windows, you prevent solid dirt particles from damaging the profile and glass. Therefore, the first step in preparing for winter is washing the windows.

Plastic translucent structures are mechanical systems, the mobility of which is ensured by fittings. Cleaning, lubricating and adjusting the fittings is the second stage of preparing windows for the cold season.

The thermal insulation properties of a window depend on the tightness of the sashes to the frame. Therefore, before winter it is necessary to clean the rubber seals, check their integrity and lubricate them with a suitable product. This is the third stage of preparing translucent structures for winter.

How to properly wash plastic windows before winter

Start preparing for winter by removing the mosquito net. Wash it under running water in the bathroom and clean it until spring.

If you have a window with a ventilation valve, close it during cold weather. However, do not forget about the need to regularly ventilate the room even in frosty weather. This is necessary to prevent the formation of condensation.

Drainage holes required
cleanse

To clean plastic windows, you should use microfiber cloths and mild detergents. Never use sponges with an abrasive layer, as they damage plastic and glass.

The detergent should not contain abrasive particles or chlorine. Also, do not use old newspapers to clean glass. They leave invisible scratches on the surface. Use a soap solution made with dishwashing detergent to clean the window.

Be sure to remove dirt from the drainage holes. They ensure the removal of moisture from the window, which prevents it from fogging and freezing. You can clean the drainage hole with a match or toothpick.

Be sure to wash the rubber seals with soapy water. Do not allow dirt and dust to remain between the seal and the profile. They can usually be easily removed with a damp cloth.

How to insulate plastic windows: deal with fittings

The fittings ensure the mobility of windows, as well as fixing the sashes in the desired position. Elements of fittings need to be cleaned from dirt and dust, as well as the application of protective lubricant. The fittings can be washed with a soap solution without abrasive particles and a soft cloth. Do not use for cleaning metal parts window treatments containing harsh chemicals.

After cleaning, wipe the fittings with a dry cloth and lubricate the moving parts machine oil. You can also use silicone oil or petroleum jelly.

The degree of fit depends on the position
eccentric

Now you need to adjust the fittings.

The degree of fit of the sash to the frame is adjusted using eccentrics or locking pins. They can provide strong, standard or medium pressure (see diagram).

In winter, it is necessary to adjust the trunnions in such a way that they provide maximum pressure on the sash. To do this, take a hex key and install the eccentric in the position indicated in the diagram. The loose fit mode should be used in the summer, while the standard fit is suitable for the off-season.

If you cannot install the eccentric in the desired position, contact the specialists who installed your window. Also call a professional if completely closed design obviously leaks air. This problem can usually be resolved by adjusting the hardware.

What to do with the seal

The seal needs to be washed
and lubricate

It was noted above that rubber seals ensure a tight fit of the sash to the frame. The consumer must ensure that the seal is clean and free of cracks and holes.

The seal is cleaned using a soft cloth and soap solution at the same time as washing the profile and glass unit.
After this, the seal must be wiped with a dry cloth and lubricated. Silicone oil should be used as a lubricant. It protects the rubber from cracking.

What else you need to know

Consumers also have other questions in the context of using plastic windows in cold period. The most common ones include the following:

Why do plastic windows leak in winter?

A plastic window can leak in two cases. Firstly, this is due to a violation of installation technology. If the installer did not ensure tightness assembly seams, the window will leak in the literal sense of the word. To eliminate this shortcoming, you need to contact the company that installed your window.

Secondly, consumers often talk about window leaks when in fact we're talking about about the formation of condensation. Moisture condenses on windows due to the large temperature difference between the glass and the air in the room. This happens when you choose the wrong glass unit, which does not provide sufficient thermal insulation. Moreover, a similar situation arises if warm air from the heating radiator does not reach the window due to the window sills being too wide. IN similar situations Consider replacing the window and/or sill.

Moisture condensation on windows also occurs due to high humidity in room. To solve this problem, ventilate the room several times a day.

Is it possible to install windows in winter?

During the cold season, the demand for plastic windows decreases. Window companies offer discounts to customers to compensate for forced downtime. Many consumers do not take advantage of this opportunity, believing that high-quality installation possible only in the warm season.

In fact, windows can be installed at temperatures down to −15 °C. In this case, specialists must use “winter” polyurethane foam, and also heat the insulating tapes to operating temperatures. The question remains of the temperature drop in the room in which the installation is being carried out. Indeed, the room remains without a window for several tens of minutes. If you have the opportunity to temporarily stay in a neighboring room, you don’t have to put off installing windows until spring. And if you live in one-room apartment, and even with a small child, it’s better to postpone installation work.

By the way, installing a plastic window in winter allows you to immediately identify and eliminate all shortcomings of the installation work. In the cold season, any draft indicating leaky seams will not go unnoticed.

You can quickly prepare your window for winter

If you have a suitable quality window, the installation work was carried out in compliance with technology, and the fittings were adjusted by professionals, then preparing for winter will not take you much time. It is enough to remove mosquito net, close ventilation valve, wash the window, lubricate the fittings and seals. After this, adjust the eccentrics to the maximum fit mode. Now you can brew tea and enjoy the comfort and warmth.

In a fairly quick period of time, plastic windows managed to take a leading position in terms of the number of their installations, since the vast majority of windows in homes and industrial buildings- these are PVC windows. In order for a plastic window to serve you for a long time, it must be maintained special care, which we will talk about.

Rules for caring for plastic windows

Caring for plastic windows is a mandatory procedure, otherwise the window will begin to lose its tightness, the fittings may fail, or the rubber seal will quickly wear out, and much more. After it has been done, it is necessary to remove the protective tape that is glued to the profile, since after a while it will be very problematic to remove it due to exposure to sunlight.

Now regarding washing plastic windows. Plastic windows must be washed with special detergents for windows and special napkins or rags. If any dirt appears on the profile, under no circumstances should you clean it with sharp objects: a knife, scraper, etc. To remove complex stains, use special means, to remove dirt from plastic surfaces or directly from PVC windows.

Before washing the window profile, we recommend that you first remove the layer of dirt and dust; this is best done with a brush made of soft and thick bristles. Then the window can be wiped with a napkin or rag, after applying detergent to its surface.

Preparing windows for the change of season

The fittings of plastic windows need to be adjusted 2 times a year.

• How to care for plastic windows in winter

Caring for plastic windows in winter includes: washing window profile and glass, as well as switching the sash clamps to winter mode so that the sash fits more tightly to the profile when closing and cold air does not pass through it. This is done before the winter season in October-November.

• How to care for plastic windows in summer

Caring for plastic windows in summer includes: washing the profile, glass and switching the clamps to summer mode so that the sash is not pressed too tightly against the profile.

• Adjusting the sashes

Due to temperature changes, the window profile may narrow and expand, and because of this, the sash may begin to rub somewhere. To adjust it, use a hexagon. How to adjust the window sash is demonstrated in the picture below.

How to care for plastic window fittings

The fittings are a complex mechanism that is responsible for the movement of the sash. In order for the mechanism to work freely, it must be lubricated with machine oil. To do this, pour oil into the moving parts of the window, then move the window from one position to another several times.

Caring for plastic window seals

Proper care of plastic windows also includes care of the rubber seal of plastic windows. Please note that exactly rubber compressor provides high-quality sealing of the window profile. Like any rubber, the window seal wears out: it becomes hard and inelastic, dries out and cracks. In order for the window seal to last as long as possible, it must be cleaned and lubricated 2 times a year, as mentioned above: before starting summer season and before the start of winter.

In order to clean the window seal, it can be either removed or cleaned in this state. If you have removed the seal, place it in a container of warm, soapy water for a few minutes, and then rinse clean water and wipe with a dry cloth. Next, insert the seal into the sash and into window hole, then applying it to a rag silicone agent, treat the surface of the seal.

Plastic window care products

To care for plastic windows, use either special sets of products for caring for plastic windows or separate ones. To care for windows you need:

• Glass cleaner (for example Clin);


• Plastic profile cleaner;


• Seal cleaner or soapy water + silicone grease;


• Machine oil for lubricating fittings.