How to attach a veranda to your house with your own hands

A veranda attached to a house, or as they say today, a terrace, is perfect place for relaxing with friends or in solitude. Correctly drawn up construction project and thoughtful original design will allow you to create a real decoration for the facade of any home. In addition, a well-designed construction project will allow you to build such an extension to the house with your own hands.

We can say that the veranda is that part of the building that provides each home with a look of completeness and aesthetics. In some cases, the construction of a veranda is planned in advance and occurs along with the construction of the main part of the house. But there are times when the owners of their cottage or country house They didn’t think about this element of the building in advance and therefore, during the operation of the building, the need arises to add a veranda. Attach a veranda to wooden house It will be more economical to do it yourself than to hire specialists for this.

Location Features

To a greater extent, the veranda is attached near the main entrance to the house, that is, in front of the main facade of the building. However, this is not important. In some cases, it is attached near the side facade. Even with this location, it will be clearly visible from the main entrance to the courtyard. When choosing a location for the veranda, it is important that it provides access to the house.

As for the dimensions of the veranda, they are determined quite easily. Its length directly depends on the length of the facade to which it is planned to make an extension. The width of the terrace is determined directly by the owner of the house. As a rule, verandas are made with a width of two and a half meters. Before starting any work on the extension, first of all, it is necessary to prepare the area, that is, to put the area in order: clean it, dismantle the porch and, if necessary, get rid of the canopy over the entrance to the house.

Project planning and development

The design of a veranda in a private house photo must be developed at the construction planning stage. Construction planning and project development is important stage construction, which should be given Special attention. First of all, you should decide on the type of veranda. She may be open type and closed. An unglazed veranda will be an excellent place to relax in the summer, however, in winter it will be unsuitable for use. In addition, it is necessary to determine how this room will be used. The veranda can act as a simple resting place, can serve as a living room or even a summer kitchen.

After this, it is necessary to begin preparing the construction project. The veranda for the house photo projects is the most important part. You can create a project yourself. To do this, you need to draw a future extension, indicate in the drawing all the dimensions, places for windows and doors. The project can also be ordered from construction company, however, this will usually take quite a long time. You can also choose already finished project from the proposed options. Below are options for what a veranda for a house can look like with your own hands, photo projects.

Construction of a polycarbonate veranda

In order to understand how to attach a veranda to a polycarbonate house with your own hands, you must first of all become familiar with the basic properties of this material. Cellular polycarbonate can be called a relatively new building material, which has become quite popular in a short time. This material is transparent and has good performance thermal insulation, which may vary depending on the presence of layers or thickness of the material. Thanks to its plasticity, its sheets can be used to create any necessary shape, which is certainly more than convenient for construction. This material is used to create not only walls, but also roofs.

As with the construction of any other building, a foundation is required for the veranda. A polycarbonate veranda will be considered a lightweight structure, so a foundation can be made for it using a simpler design. A strip foundation works well, which is done as follows:

• it is necessary to dig a trench fifty centimeters deep along the entire perimeter of the future veranda. The width of the trench should be approximately 30 centimeters;
• At the bottom of the trench you need to lay a sand cushion twenty centimeters thick and fill it with a small amount of water;
• Next, you need to pour concrete on top of the sand and lay it with reinforcement;
• After this, you need to let the foundation dry completely. This may take about two months. If the weather is hot, then periodically the foundation needs to be moistened with water and covered with film so that it does not crack.

Frame

After the foundation has completely dried, you can begin assembling the veranda frame. To do this, a plinth is laid on the foundation, which needs to be covered with roofing felt and then the timber for the base should be laid horizontally on it. In the corners, four supports must be attached vertically to the beam. At the top of the supports they need to be fastened to the beam in a horizontal position. After the upper and lower bases are fastened together, you need to screw vertical posts between them with a distance of 650 millimeters from each other. Thus, a frame is constructed, which should then be sheathed with polycarbonate. Using the same scheme, you can make a frame from a profile pipe.

Important point: everything wooden elements The frame must first be treated with a special antiseptic to make it resistant to moisture and pest damage.

Roof

In order for a polycarbonate veranda attached to a photo house to be durable, you need to ensure the construction good roof and its waterproofing. To do this, you need to place the rafters on 2 upper beams, which lie parallel to each other. The rafters can be made independently from boards with a thickness of forty millimeters. The distance between the rafters should be made depending on the dimensions of the polycarbonate. The transverse lathing can be made from boards measuring 20 by 10 millimeters.

Sheathing

Polycarbonate sheets should be cut in such a way that, as a result, its internal channels look down to the ground. This will make it much easier to remove dust. The UV protected side of the material should be facing outwards. The end part of the material should be closed using a profile and sealed with a special tape. If this is not done, condensation will make the plastic cloudy. Next, you need to make holes for self-tapping screws, with the help of which the cut sheets are attached to the frame of the building. The joints between the materials should be connected using a split profile. Below are photos of ready-made verandas and terraces for the house.

Features of adding a veranda to a wooden house

Attaching a veranda to a wooden house with your own hands means making an excellent place to relax and giving general appearance home of aesthetics and originality. The peculiarity of building a terrace or veranda for a wooden house is that it must also be built from the same material.

Base

When building a wooden veranda, a strip foundation design is ideal. It is important to follow the technology for constructing this type of foundation:

1. The area needs to be prepared. To do this, you need to clear the construction area of ​​debris and grass;
2. Next, you need to mark the perimeter of the future terrace;
3. Then you should begin to create a trench, which for a wooden veranda should be at least 1.2 meters deep and at least 30 centimeters wide;
4. After this, the dug trench should be covered with sand and compacted well;
5. Next, you need to lay reinforcement at the bottom of the trench and make formwork, which should be several centimeters higher than the ground level;
6. Then the concrete is poured. It is necessary to give it time to dry completely and only after that you can proceed to waterproofing the foundation and next stage construction.

Frame installation

Extension of a veranda to a wooden house requires the installation of a frame made of timber. When installing the frame, you should install bottom trim. Using anchors, you can attach the beam to concrete at a distance of 60 centimeters. In the corners you need to make a connection like a straight lock. Also, in the corners of the frame you need to install logs on which the floor covering will be directly laid. To make the logs more rigid, they should be fastened with staples. Next, vertical posts should also be installed in the corners with a distance of 1.2 meters. Upon completion of the installation of all racks, the top should be tied using nails and screws.

An important point: when working with wood, to create a more durable fastening, it is best to use screws as a fastening element.

Roofing device

Roof installation in wooden veranda performed using the same technology as in the construction of a roof for a polycarbonate terrace. However, the distance between the rafters should be 70 centimeters. The roof design for the veranda should include a sheathing into which insulation can be laid. Plywood is attached on top of it and roofing felt and tiles are laid. Such simple design roof allows you to build a veranda for the house with your own hands.

An important point: ventilation holes should be left in the roof structure, which are best done on the sides. This is necessary for free air circulation.

Walling

There are several ways to attach walls to the main structure, but to do the construction yourself, the easiest way is to fasten it using special anchors with spacers. In this case, additional strength can be ensured by fastening the structure with staples.

For covering the veranda for wooden house You can use either timber corresponding to the size of the beam when building a house, or plywood. Plywood is a simpler option, so we’ll consider it. In order to sheathe the veranda frame with plywood you will need only three tools:

• long meter tape measure;
• electric jigsaw;
• screwdriver

The plywood should first be cut into necessary sheets and then attach to the vertical posts. First, you should trim one side with plywood and insert insulation into the distance between the posts, after which the other side is sheathed. Despite the fact that this option for covering a veranda is quite simple, the terrace will ultimately turn out to be a very warm and functional room.

An important point: do not forget about building a floor on which you can pour expanded clay and compact it well. Expanded clay is an excellent material that will provide good thermal insulation and will help you do wooden extension as warm as possible and suitable for use in winter period time.

The installation of windows in such a building is one of the most difficult stages of work, since making wooden windows yourself is quite difficult and extremely expensive. The best options are PVC windows, which can be made to order. You can install such windows yourself or entrust them to specialists.

Video on how to build a veranda for your house with your own hands

Polycarbonate veranda photo extension to the house. Most people have country plots or private premises for relaxation, isolation from noise, and for working in their garden plot. So that at the dacha you can not only have a pleasant time, but also create a comfortable and cozy place. For a room with the best view effectively arranging the veranda of a small building with a good view, comfortable furnishings and a quiet atmosphere. It is possible to create a veranda actually from different materials, however, the use of polycarbonate is in particular demand.

Properties and characteristics of polycarbonate for verandas

• Polycarbonate is transparent, but has different colors. Which will look great in design.
• Withstands strong pressure changes. Therefore, they are used in all regions of Russia.
• Excellent sound insulation.
• Flexible and resistant. Doesn't break from powerful loads. The polymer is ten times lighter than glass.
• Does not burn, does not allow water to pass through, does not fade from sunlight, and is not afraid of frost.
• A durable material that does not change its properties even after ten years.
• Easy to install.

Types of polycarbonate verandas

Open veranda made of polycarbonate. Open or summer verandas made of polycarbonate are intended to provide reliable shelter during fine weather or possible precipitation. The structure of such structures is light and contains integral supports for the purpose of securing the roof and the possibility of fencing.
Covered veranda made of polycarbonate. For closed verandas alternatives in addition to walls and roofing imply the presence of door or window openings, and in addition, insulation of only the perimeter of the building. When using colorless polycarbonate, you can do without windows, since the entire wall is made of a high panorama. Such a ruling is allowed for both the door and the roof if you want to be open to the atmosphere in convenient circumstances. It is impossible to completely renounce windows, since in the summer they create freshness.

Built-in veranda. Such verandas are buildings built into part of the house; when planning the structure of the house, a veranda is immediately planned. Previously, these buildings were boring and had ordinary construction shapes. With the advent of polymer sheets, owners had the opportunity to expand and decorate their homes. Polycarbonate is plastic and easy to use; it is possible to make a semi-rounded veranda.
Attached veranda. These polycarbonate verandas are made when the house itself has already been built. The polymer itself is quite cheap and easy to use, a huge number of owners build new verandas, sometimes 2 of these verandas are attached to the house, sort of like for summer fun, either a barbecue or warm building For indoor garden with flowers.
Sliding system made of polycarbonate for the veranda, a simple, impact-resistant and durable material. The principle is that verandas adapted to housing are not of large volumes, however open view system, does not in any way form a feeling of pressure from an internal place, but, on the contrary, gives an absolute feeling of independence and a new atmosphere.

Types of polycarbonate verandas

Arched. Made from polycarbonate and looks good. This type They are mainly used for attached verandas; the roof is made semicircular; there is a lot of light and the necessary heat in the room. Simply put, the owners of such structures use them as greenhouses for seedlings or for growing flowers.

Round. In the project, this veranda does not differ from a square or rectangular assembly. The only exception is the outer wall; it sticks out a little, forming a semicircle of this shape (at the buyer’s request). This trick allows a person to slightly increase and expand the interior of the building.
Square. Verandas of this kind are also called rectangular; they take up little space and are suitable for have a nice rest. It is comfortable because it is standard without any bulges and vice versa.

Interesting Facts. When building any structure, it is necessary to take into account that the coating is not proportional to the floor, since dust and dirt will accumulate on the surface.

Polycarbonate veranda: how to position the foundation

The veranda is considered to be simple structures, the foundation is created using conventional technology. This definition refers to a strong foundation of a structure using reinforcement.
The construction of the foundation of a house for a veranda made of polycarbonate begins with marking and excavating places, they are dug in the areas where they intend to install walls. The appropriate depth for such a house base is 600-800mm, however, if you want to create a truly reliable veranda, then it is preferable to raise it up to the freezing depth of the ground. As for the width, in this case a volume of 250-300mm will absolutely do.

The dug trenches are strengthened by frame technology, subsequently formwork is inserted to a height of up to 300 mm and this is always filled with concrete. Everything here is as usual, familiar, including the drying procedure, where control should be exercised. In order not to develop cracks (wet it with water and cover it with film).
Frame. Construction of the frame begins from the lower tier. Along the circumference, beams are placed on the pillars, interlocked with a lock and self-tapping screws or staples. Approaching 2 tiers, in horizontal bars make a groove for vertical supports. After all the vertical posts are installed and firmly attached vertically, you need to arrange top harness supports To achieve an effective result, a long beam is placed on them, the end of the beam is placed under the roof and bolted to the supports.

Polycarbonate roof. A polycarbonate roof can be described as the more ordinary and simpler of absolutely all roofing systems - for its purpose it is necessary to create only a sheathing. The roof is not insulated and is not hemmed underneath in any way. If the walls are already standing, then laying a sheathing block on them will not amount to practically any work - this will be the first step in constructing a polycarbonate roof for the veranda. The thickness of the timber must be considered in such a way that the roof can withstand overloads from snowfall in the winter. It is necessary to think about using uneven timber, and planks 40mm wide and 50mm wide. The base of the roof, organized in this way, can withstand very large overloads.
Polycarbonate glazing. Glazing a veranda with polycarbonate can be done using 2 methods - in 1 case it is possible completely, but then in the summer it will be hot on the veranda without ventilation, and in the second case it is possible to make frame glazing, which will become more the right choice. Directly this kind of aspect to the process will make it possible to use the veranda not only in summer period, however, in winter time, in addition, equipping this place with underfloor heating or two conventional heating radiators.

Advice when building a polycarbonate veranda, it is possible to use not only timber, but profile pipes will be much stronger.

Polycarbonate canopies built for the house

Such canopies, adapted to an individual dwelling in the form of canopies over the porch, will perfectly complement the overall construction view and will provide an opportunity to hide from the rain or the sun's rays. They also use a carport from snow, rain, and for some, instead of a garage.

Equip the visor with polycarbonate with my own hands not difficult at all. The layer of this material used makes it possible to withstand all kinds of loads in weather conditions.
It is worth highlighting in this case that the cost of polycarbonate is not expensive and exists a large number of The colors of the material and its use can be as you wish. Canopy extension. If you decide what you will use to make a canopy, you need to clear the place of debris and make a rough drawing. Make markings for the pillars and dig 50-80 centimeters wide. We fill the pillars cement mortar and leave for two days to harden. It is good to tie the pillars with a special thread. When ready, you can begin assembling the canopy. To start work, you first need to use solid sheets, and only then select the joints with the remains of polycarbonate. Fastening polycarbonate using special self-tapping screws.

Caring for polycarbonate

• When installing polycarbonate, be sure to read the operating instructions on the packaging.
• The material must be transported horizontally; you should not walk on it or step on it because it is flexible. Store it under a covered surface.
• When cutting polycarbonate, remove protective film and use a special knife for construction.
• To clean the surfaces you need to use a damp sponge or cloth with a soft surface.
• Detergents containing various acids, it is better not to use. It’s better to wipe with just water and powder.

Veranda made of polycarbonate is great choice for a comfortable environment and view. The simple design of polycarbonate allows you to do everything yourself. The transparency of polycarbonate allows you to create the appearance of a natural landscape at any time of the year. The material is not expensive and anyone can afford it. The desire to make a beautiful veranda from polycarbonate will not be difficult. Progress has reached the point where people can enjoy the view environment and atmosphere.

Modern outbuildings that increase the comfort of living in a house include not only utility structures, but also recreation areas. In conditions of high prices and, as a consequence, a shortage of free space for construction the best option to organize a place of rest and relaxation, terraces attached to residential building or freestanding. The best material for installing a roof for them experienced craftsmen consider polycarbonate plastic, which allows you to create light, translucent structures that create an openwork shadow. You can easily make a terrace with a polycarbonate roof with your own hands. In this article we will tell you how to choose the right material, build a frame and install polycarbonate yourself.

Polycarbonate plastic - modern polymer material, which is an ester of bisphenol A and carbonic acid. It has light transmittance up to 92%, high impact resistance, load-bearing capacity and resistance to atmospheric moisture. The advantage of polycarbonate is its ultra-light weight, 0.8-4.3 kg, which makes it easier to install the structure yourself. Experienced roofers recommend using this material if the roof slope exceeds 5-10 degrees. The following are produced:

Note! Translucent roofs for terraces are made with your own hands from any type of polycarbonate, the thickness of which is 6-8 mm. To cover seating and eating areas, it is recommended to use material in warm colors (yellow, red, orange, which promote relaxation and improve appetite.

Basis of design

The design of each terrace consists of 3 main elements: load-bearing pillars, rafter frame and directly roofing material, which is polycarbonate. To prevent it from becoming warped or deformed during operation, the frame is assembled in accordance with the following requirements:

1. Natural wood, aluminum, and steel are suitable for the manufacture of roof truss frames. To make a roof for a terrace with your own hands, use a profile whose section thickness is 60x60 mm or 60x40 mm.
2. To last longer, the wooden frame elements are coated with an antiseptic compound and varnish, and metal paint for protection against moisture.
3. When creating a roof for a polycarbonate terrace, it must be taken into account that the structure must have a slope of at least 5 degrees. Optimal slope To remove atmospheric moisture, an angle of 10 degrees is considered.
4. The distance between the rafters should not exceed 100 cm. If the roof is mounted from thick monolithic polycarbonate, the pitch between the rafters should be kept to 50-70 cm.

Important! During the installation of a roof for a polycarbonate terrace, the rafters are placed so that the joint of the sheets is above supporting element, on which it is fixed connecting strip. This technology allows you to make the joints between elements more airtight.

Installation sequence

The service life of polycarbonate structures depends on the quality of the material in one half, and on the quality of installation in the other half. A roof made of polycarbonate plastic has the property of thermal expansion, that is, it changes in size as the temperature rises, which must be taken into account when installing it yourself. To prevent the material from being deformed during the process, it cannot be fixed rigidly to the frame. The structure is assembled as follows:

Please note that when installing a terrace roof, polycarbonate must be placed so that the stiffeners are located along the slope. This allows condensation formed inside the cells to drain, gradually evaporating.

Advantages of the design

When creating a terrace project professional craftsmen They recommend paying attention to polycarbonate structures that are easy to assemble with your own hands. This material is easy to process and does not require a special tool for installation; however, it can be used to successfully implement complex design ideas. The following advantages of polycarbonate roofs are highlighted:

1. A light weight. Since 1 square meter polycarbonate plastic weighs only 0.8-4.3 kg, its installation does not require a massive frame and a capital foundation, which reduces the cost of time and money for construction.
2. Transparency. The transparency of the material is a huge plus for the terrace, as the roof turns out to be light, openwork, and transmitting sunlight.
3. Flexibility. Thanks to the flexibility of the material, craftsmen create complex arched, dome and tent structures without the use of special equipment.

Video instruction

A feature of any veranda, which is essentially a terrace adjacent to the house, is its location on the same level as the residential building directly next to the exit, which allows, without actually leaving the house, to be on the outdoors. This was not only the main reason for the popularity of such extensions over several centuries, but also determined the parameters of the materials used in their construction.

The basic requirements for a veranda are quite simple and at the same time capacious. She must be:

• light;
• spacious;
• reliable;
• warm if the veranda is closed;
• beautiful;
• cozy.

Today, all of the above properties are best demonstrated by polycarbonate verandas.

Extraordinary transparent plastic

Polycarbonate, or clear polymer plastic, was created as an alternative ordinary glass. The first sheet of this material was first produced in Israel in the mid-70s of the last century. Since then, cell phone and monolithic polycarbonate has become widespread in a variety of industries. First of all, due to our own unique characteristics, of which the most basic are:

• service life more than 10 years;
• high strength, superior to any industrial transparent materials;
• degree of transparency reaching almost 90%;
• resistance to external environment and exposure to ultraviolet radiation;
• ease of processing;
• light weight;
• acceptable cost.

All together made the material indispensable in construction, and especially in private residential buildings. Gazebos, terraces and verandas made of polycarbonate have become an indispensable attribute of most country houses and dachas.

Features of the open veranda

As already mentioned, the veranda must meet a number of requirements, which determines the choice of material for construction, in this case the use of polycarbonate. The main influence on its use is functional purpose verandas: open or closed.

Open, or summer, verandas made of polycarbonate, as well as those made of other materials, are usually used only in the warm season and serve as a reliable shelter from the sun's rays or possible precipitation. The design of such buildings is quite simple and includes mandatory supports for attaching the roof and possible small fencing. Polycarbonate sheets can be used for both fencing and roofing. Load-bearing supports can be made from wooden beam, metal profile or brick, that is, any material used for similar work.

Characteristic differences of closed structures

For closed options, in addition to walls and roof, it is assumed that there are door or window openings, as well as thorough insulation of the entire perimeter of the room. Using transparent polycarbonate can eliminate the need to install a window, as the entire wall becomes a large panorama. This solution can also be used for doors or roofing, creating the effect of a permanent outdoor presence in comfortable conditions. You cannot completely abandon windows, as in summer they create the necessary coolness.

Types of polycarbonate and its advantages

To build a veranda or other building, you can use two types of polycarbonate:

• honeycomb sheet, consisting of individual plates connected by a partition;
• monolithic sheet with no voids inside.

Possessing almost identical advantages, they have their own characteristics. The first retains heat well, and the second is superior to ordinary glass in all respects.

Verandas made of polycarbonate compare favorably with those made of other materials, even if the use of this material is limited to certain structural elements. The most important advantages include:

• significant reduction in construction costs, which is achieved not only by the acceptable cost of polycarbonate, but also by reducing total weight design and, as a consequence, the number of elements that impart rigidity;
• ease of processing, allowing you to install even large-area sheets yourself, including cutting and subsequent joining;
• good resistance to all precipitation, which, combined with a competent design, allows you to observe natural phenomena “from the first row.”

Disadvantages and ways to eliminate them

At the same time, one cannot fail to note the disadvantages of this material, which must be taken into account during operation:

• susceptibility to mechanical damage, which requires some care during use;
• the ability to scratch even with light touches, which reduces transparency and requires the mandatory elimination of potential sources of damage, such as tree branches or shrubs;
• intolerance chemical solutions, which are contained in some types of detergents;
• the ability to change its dimensions under the influence of temperature, which can be prevented by providing gaps between the sheets;
• while creating closed structures Be sure to use a sealant.

The use of precautionary measures during the installation and operation of a polycarbonate veranda makes it possible to effortlessly minimize the impact of these shortcomings.

If installation is done by hand

Ease of processing and low weight often become decisive factors when deciding to build a veranda with your own hands. Usually in this case it means attached verandas made of polycarbonate, the need for which arose after the completion of the construction of the main house.

The construction process is no different from the technology for constructing a veranda from any other material:

• preparation of a project for future construction;
• installation of formwork and pouring of the foundation (strip, monolithic or columnar);
• installation of support posts (made of timber or metal profile) and floor;
• installation of rafters (wooden or metal);
• installation of polycarbonate walls and roofs.

In this process, the main thing is to correctly select, prepare and secure polycarbonate sheets.

Features of working with the material

When selecting and installing polycarbonate sheets It is advisable to use the following recommendations:

• until termination installation work protective covering cannot be removed;
• when working with honeycomb sheets, the ends must be sealed to prevent moisture from entering inside;
• For open projects A sheet thickness of up to 10 mm is sufficient, for closed ones you can choose 16 mm or more;
• for window or doorways It is recommended to use monolithic sheets, which are best installed in a frame, like ordinary glass;
• the roof angle for a polycarbonate veranda is recommended to be at least 40° to prevent the accumulation of water or leaves;
• moving through sheets occurs using special devices, otherwise they may crack;
• Attaching the sheet to any base is always done only with the use of rubber gaskets to prevent damage.

Unlimited use cases

If you look at all existing verandas and terraces made of polycarbonate, photos of which are in the article, you can choose any suitable option for the most demanding owners.

Polycarbonate goes well with everything building materials, thanks to which it easily fits into the design of any private building. A variety of colors only expands the application options.

The ability to take almost any shape opens up endless options for creating a roof. This is most clearly demonstrated by children's verandas made of polycarbonate.

Facilities for children

Preschool institutions most need bright structures that create shade during the heat and reliable protection from the rain. Polycarbonate verandas for kindergarten successfully combine pleasant appearance, unusual shape and ease of perception.

The standard parameters of the veranda make it possible to establish serial production of the most popular models, which, coupled with simple installation reduces installation time to 1 day.

Any decision is usually made after analyzing opinions on the Internet or the experience of acquaintances or friends. If we summarize the available information on building a polycarbonate veranda, the reviews are mostly positive. The main advantages of the material are confirmed by the majority of users. Among the main disadvantages, one can highlight the strong heating of a room with a polycarbonate roof, even with open windows, a slight loss of transparency after time and the ability to scratch even from slight mechanical stress.

Reading time ≈ 3 minutes

Building a small veranda from polycarbonate sheets allows you to quickly get an inexpensive extension to your house. Finished design can be used for relaxation fresh air in summer time. Due to the affordable cost of materials and the ease of their assembly, making a terrace will require a minimum of time and money.

Polycarbonate veranda base

The optimal solution would be to make a strip foundation. A lightweight polycarbonate veranda made by yourself allows you to save on preparing the base. To make a foundation, you will need to dig a trench and fill sand cushion, install the formwork. Place reinforcement inside and fill the resulting form with concrete. The hardening time for the base will be approximately 1-2 weeks.

Preparing the floor and assembling the main structural elements

Making the floor will require pouring sand and compacting it tightly. Next, you need to pour a small layer of fine crushed stone and lay the reinforcing mesh. The elements are connected using ordinary wire. Next, the screed is poured, which will serve as the basis for subsequent finishing.

So that the veranda adjacent to the polycarbonate house has stylish look, can be used as flooring material tiles or terrace board. Raw materials will have long term service and will highlight the uniqueness of the extension’s decoration. When Finishing work are completed, the contractor can assemble the main components of the structure:

1. Attach the lower profiles to the strip foundation, install adapter corners between adjacent elements.
2. Install the wall profiles, firmly attaching them to the wall with dowels.
3. Mount corner profiles, install the upper profiles on which the roof will be laid.
4. Install the remaining vertical profiles (for subsequent installation of doors, windows, to strengthen structures with long walls).

In the future, a polycarbonate veranda attached to the house is made, no less simply. But it is important to remember that there is no need to tightly fix the jumper profiles: in the future, polycarbonate sheets will be installed between them.

Assembling the walls and roof of the veranda

When the veranda frame is completely ready, you can begin installing the polycarbonate sheets themselves. First of all, you need to fix the sheets whose profiles are adjacent to the walls. Next, you can install the remaining wall elements, excluding closing the passages and areas where the windows will be located. In order for a DIY polycarbonate veranda to be truly practical, it is recommended to install a couple of windows and leave space for installing a ventilation grille.

The next step is to glaze the veranda with polycarbonate on top. To do this, support profiles are installed, which are responsible for fixing the sheets on the roof. Next, the sheets themselves are mounted. If necessary, you need to leave space for installing the window in the upper part.

Installation of windows and doors

After the polycarbonate has been laid on the roof of the veranda and the profiles have been completely fixed, you can proceed to the installation of doors and windows. Can be used metal-plastic products with single glazing. They are light in weight and can be easily mounted on profiles. Additionally summer terrace made of polycarbonate may include a small ventilation grille(with closing blades).

IN last resort Installation of polymer gutters responsible for drainage of rainwater is being carried out. Thanks to them, the veranda at the dacha from cellular polycarbonate will serve the owners for as long as possible. Then the terrace is arranged: armchairs, sofas, tables are installed. Using the attached photos you can find many original solutions to decorate the extension. It is recommended to additionally install flowerpots with fresh flowers on the site and attach curtains. Fabric sheets will protect well from the sun and give the finished veranda a stylish look.