How to care for plastic windows. Proper preparation of plastic windows for winter with your own hands How to properly prepare plastic windows for winter

At first heating season- it's time to think about how to prepare plastic windows for winter. To complete the work you will need a Phillips screwdriver and a hex key.

First of all, wash the windows, profile, window sills and slopes. We recommend using small amounts of non-aggressive detergents and a soft sponge. For achievement best result You can open the window sash and use a sharp object to remove dirt that has accumulated in the drainage channels. For these purposes, you can use a toothpick or match. Clean drains will freely drain excess water and prevent ice from forming in these places.

In the cold season, the seal should be additionally protected with technical Vaseline or silicone grease. The sealant is coated with the product around the entire perimeter. This approach will protect the material from freezing and drying out.

In order to ensure smooth operation of the mechanism, the moving parts of the window unit should also be lubricated with Vaseline or a silicone-based compound. Dust does not stick to silicone, which allows you to keep your windows clean.

If you see it on sale special sets for the care of seals and fittings, do not pass by, be sure to purchase. Manufacturers recommend performing this treatment twice a year.

A loose window handle is one of the common problems plastic windows. In order to return it to its original state, turn the handle to the “open” position (so that it is parallel to the window sill), then turn the handle cover located at its base by 90 degrees. Under the trim you will find two screws that need to be tightened with a Phillips screwdriver.

Next stage preparing plastic windows for winter - checking the tightness of the sash. For such an experiment, you will need a regular piece of paper, which you need to insert into the flap of the sash, and then close it. If the leaf is removed with some effort, then everything is in order with the density. If the paper can be removed from under the seal without any hindrance, then it’s time to set the window fittings to “winter mode”.

Setting up is quite easy. To do this, open the sash; on the end part you will see roller bushings. U different manufacturers bushings may have different kind, but in production the middle position is always set. You need to insert a hex key into this sleeve and turn it so as to ensure maximum pressure. In this way, the fittings are adjusted to suit the required season. After this, all that remains is to close the sash. The increased force on the handle will indicate that all actions were performed correctly. The sash will close tighter. The next fitting adjustment should be made with the onset of spring. This approach will avoid premature wear of the seal.

As you can see, there is nothing complicated in preparing plastic windows for winter. For further defect-free operation of window systems, it is important to maintain normal air humidity (no more than 45-50%) and ensure correct work exhaust and supply ventilation. You can check their effectiveness using the same piece of paper. To do this, bring it one by one to everyone ventilation holes. More accurate data can be obtained by using an anemometer. Do not forget that windows should not be perfectly sealed, as this leads to the formation excess moisture in the air. Arrange airing sessions for the apartment at least 2-3 times a day.

How to prepare plastic windows for winter?

Metal-plastic profiles – perfect solution for glazing of residential and premises. They perfectly protect the room from heat leakage, street noise, drafts and dust and have significant advantages over conventional wooden frames. Quality product can last 15-20 years without problems.

To avoid unforeseen inconveniences during operation, the PVC structure must be periodically maintained, namely: promptly switch to winter and summer mode. The main topic of our article is preparing plastic windows for the winter season. We assure you: it is not at all difficult and anyone can do it if you follow the list of recommendations below.

Let's start with cleaning

The first thing you need to do is wash the window thoroughly. This means not only double-glazed windows, but also profiles, window sills, and plastic-lined slopes. We strongly do not recommend using caustic or abrasive products. detergents! They can damage the plastic coating, leaving unsightly streaks of a darker or yellowish color on it. Clean with soft cleaning gels.

For safety reasons, you should not use a steel wool to remove dirt - it will probably scratch the plastic and its aesthetic appearance will deteriorate. You will need a soft flannel cloth, rags or sponge. It is worth washing not only the inside, but, if possible, the outside as well.

Pay special attention to the drainage channel. You can get rid of debris or debris stuck there by carefully using a regular toothpick. This will prevent stagnation of water in drains and obstacles in movement window sashes. To windows pvc in winter served without problems, it is also necessary:

And a little more about seals. They must be periodically lubricated with special lubricant or technical petroleum jelly. Timely care will help avoid drying out and freezing. But a preliminary inspection revealed wear and tear - don’t worry: replacing the seal is easy to do yourself.

Select the required option at construction market and install, after removing the old one (using a flat-head screwdriver). Seat It is advisable to treat it with lubricant. Afterwards, the entire area of the seal is covered with it.

Setting up window fittings for winter

Before the cold weather approaches, you need to adjust window fittings: the frame should be pressed more tightly against the glass unit: this is the only way to prevent drafts. To perform the action you will need a hex wrench. If you don't know how to adjust the fittings, use our tips.

The horizontal sides are adjustable by panels at the bottom and top. Take a closer look: they have a special hole for a hex key.
The top panel is adjusted when the window is open. Raising the edge is done by rotating the key to the right.
If the window is on the ground floor and can be reached from the outside, you will not have to open the sash. A loop located at the bottom allows you to adjust the vertical sides. To get to the hex hole, first remove the protective cap.
To increase the pressing force of the profile frame, you need to monitor the eccentrics. To do this, turn them to the right. The guide will be specially applied marks that determine the pressing force. Attention! If the mark is turned towards the seal, the pressure is strong. Often the eccentric is turned with ordinary pliers.
In the places where the loops go, there are devices responsible for the clamping force. How to recognize it? That's why the tongue protrudes so much. The longer, the stronger the pressure of the frame against the window. Measurements are usually made with a hex wrench.
Under no circumstances apply strong pressure to the tongue! This will inevitably lead to rapid wear and complete failure of the window seal.
Do not neglect adjusting the hinges when switching the PVC structure to winter mode. Pay attention to bottom loop Most manufacturers provide a protective cap that is removable. After this, a special bolt is screwed in.

If you have carried out these manipulations, the adjustment of plastic windows for winter is completed. Everything is quite simple: the main thing is to be careful and consistent. But it also happens: everything is done correctly, but the window still does not retain heat well, and a draft penetrates into the room. Why this happens and how to correct the situation - we will tell you further.

Preparing plastic windows for winter: how to retain maximum heat?

Does the PVC profile retain heat poorly, let noise through, and does condensation accumulate on the glass unit? A depressurization has occurred that requires immediate intervention. The most common causes of the problem:

Shrinkage of the walls occurred after the plastic windows were installed. Solving the problem is easy - just adjust the fittings.
The seal has outlived its useful life. The replacement we wrote about above will help here.
The junction of the slope and the frame is not airtight. You will have to remove the slopes, insulate them and install them back. If you do not have enough experience to carry out this manipulation, invite a specialist.

Single-chamber and double-chamber double-glazed windows in extreme cold require additional insulation. It can be produced using film, preferably frost-resistant. For high-quality insulation you need to know that:

Pasting the film indoors, not outside outside windows are the most efficient and energy saving.
When gluing the film, control the uniformity and tension force. If this is not done, breakthroughs may occur.
There is no need to replace the film for minor damage. Carefully seal the breaks with tape.
The best option– frost-resistant film (has high density and a characteristic yellowish tint). We do not recommend buying it on the market. It makes more sense to visit a large hardware store that sells certified products from trusted manufacturers.
At the same time durable and quite decorative, greenhouse film is used for gluing the window on the side of the room. And also - it is durable.
Do not use for fixing construction stapler or push pins! They tear the material. All you need is tape.

IN Lately Eco-friendly and reliable PVC insulation is used. It is resistant to deformation and severe frosts. We hope we have comprehensively talked about how to prepare euro windows for winter and have been useful. Good luck!

Thanks to plastic windows, homes have become more comfortable and cozy. Winter has ceased to be a terrible enemy. Distinctive features of PVC windows are their strength, reliability and long service life. But these products also require periodic repairs.

So that windows can protect you in winter time, maintaining heat, it is necessary to produce preliminary preparation. Thanks to such work, the windows will function normally. Preparing windows for winter includes a number of activities. How to switch windows to winter mode? How to prepare plastic windows for winter?

Let us consider in detail the following algorithm of actions:

First, you just need to wash the windows and do it thoroughly. It is necessary to wash the slopes, the window sill, and the profiles, especially if they are made of plastic material. Do not use aggressive cleaning agents for cleaning. chemicals. Glass needs a rag and a soft sponge to clean. Windows should be washed on both sides: internal and external. When opening PVC windows, pay attention to the channels intended for drainage; they also need to be cleaned. This can be done using a toothpick or other sharp instrument or object.
Pay attention to the moving components of the window hardware. Pressure rollers - this is where the largest cluster mud. Dirt is the main obstacle to the normal functioning of these elements. To clean, use a brush that has hard bristles - this will help get rid of dust and old grease.
Once cleaning of windows and areas that are difficult to reach is completed, it is necessary to lubricate the mechanisms. For this you will need silicone lubricant. Buy lubricant foreign manufacturer, since it has a long service life. If you don't want to spend your money on it cash, then you can use solid oil. According to many, ordinary oil can be used as a lubricant. vegetable oil. But this is far from true. After a certain period of time, the vegetable oil dries out and becomes a kind of “sandpaper” that can make the mechanisms unsuitable for functioning. This may happen after about a year. When you lubricate the pinch rollers, be sure to turn the handle at this moment. Thanks to this, the lubricant can be evenly distributed throughout all parts.
Next, check the condition of the seals. This procedure must be taken seriously, because seals affect general meaning temperature in the house. If strange noisy sounds appear inside the room, and the windows sweat, then these signs indicate a damaged seal. To increase the service life of the seal, it is necessary to clean and lubricate it occasionally. Use imported silicone as a lubricant. Lubricate the entire length of the seal to prevent freezing and drying out. If you notice wear and tear, you need to replace the product. It is possible to do this yourself. Before purchasing, be sure to pay attention to the shape of the planting area because it may vary. The sealing element must be removed using a flat screwdriver and install the new product. To make the job easier, lubricate the planting area. Once the work is completed and the sealing thing is set, it is necessary to carry out a generous treatment of the sealant, from its upper part.

Follow these four steps when cleaning out accumulated dirt. This is the first step to prepare the windows.

Adjusting the window for winter

As soon as winter approaches, it is necessary to carry out window adjustments. This will help switch them to winter mode. The procedure is that the frame must be pressed tightly against the window to prevent the penetration of drafts. For this job you will need a hex wrench.

The sides, which are positioned horizontally, are adjusted from top to bottom across the panels. To carry out such adjustment, there are sockets in the window hinges intended for a hex key.

To adjust the top panel, the window must be open. To lift the edge of the panel, which is located opposite the hinge, the tool must rotate in right side. To lower, rotate the tool in the opposite direction.

If the plastic window is located low, but you can control it from the street side, then you do not need to open the sashes to adjust it. Therefore, you will be able to make an offset of two millimeters. Or eliminate the bevel, also by two millimeters.

The loop located at the bottom allows you to adjust the vertical sides. To gain access to the hex socket, you must remove the safety cap. Also, to raise the tool, twist it to the right, and to lower it, turn it in the opposite direction. The shift value is two millimeters.

When changing the pressing force along the vertical and horizontal parts, do not forget that the eccentrics responsible for this are located throughout the edging. When turning the handle, each eccentric moves beyond its clamping point.

To increase the frame pressing force, the eccentric must turn to the right. To reduce the force, it must turn in the other direction. Each eccentric has specially designed marks. Thanks to them, you can determine the pressing force of the frame. Therefore, if the mark is located where the seal is, this means that the pressure is strong. If the mark is turned where the street is, then the clamp is weak.

Some windows have eccentrics that can be turned using ordinary pliers.

In the places where the hinges are located, there are devices that regulate the clamping force. The degree of force is determined by the protrusion of the tongue. The length of the tongue determines the tightness of the frame against the window. Changing the length of the tongue is done using a hex key.

To increase the length of the tongue, the tool must be turned to the left if the loops are located on the left side. If the loops are located on the right, then you need to twist it to the right. During winter period you need to press the frame as hard as possible. IN summer period the pressure should be weak.

The main thing is not to overdo it. Do not press the frame too hard, otherwise the sealing material will wear out faster.

Also, in preparation for the winter season, the hinges also need to be adjusted, that is, pressed firmly. From the hinge located below, you need to remove the specially designed cap and turn the bolt located perpendicularly.

You can adjust the pressing force of the hinge, which is located on top, if there is a flap. Its installation is carried out for ventilation, thus you can use a key. During this work, hold the window, because it is fixed using a single hinge.

The procedure for insulating plastic windows

If after some certain period after PVC installations Since the windows begin to let in drafts and do not retain heat, it is necessary to insulate them. But first you need to find out the reasons for these problems. Let's look at the main reasons:

The rubber seal has worn out. A replacement needs to be made.
The area where the frame and slope meet is depressurized. For liquidation this deficiency, the slopes should be removed, insulated and reinstalled. We close the windows.
It is possible that after you installed plastic windows, shrinkage of the walls may have occurred. To eliminate this problem, additional adjustment of the fittings is necessary.

On winter days, plastic windows can be insulated using film. This method is expensive, but at the same time the most effective. The film is applied from the street side. In rare cases, thermal insulation is carried out with inside. The film must be stretched over the entire surface of the frame and must be attached along the edges.

During this process material tension, force and uniformity must be controlled simultaneously. If the material is poorly tensioned in any place, strong wind may form a breakthrough. If it works, then the hole should be sealed with tape so as not to waste money on purchasing a new product.

When choosing a film material, you need to pay attention to frost-resistant characteristics. Required material has a yellowish tint. High-quality film is difficult to find on the construction market, so buy it at a large construction market. So as not to spoil appearance premises, buy material that is intended for greenhouses. This product has a higher cost, but it will last a long period of time due to its high level sustainability.

Installation of this film consists of attaching it to the edges of the frame using tape. The windows need to be closed.

Instead of tape, you can use a construction stapler, but defects will appear on the frame. The main processes of thermal insulation and sound insulation are provided by double-glazed windows.

There is PVC insulation that can replace film. This insulation is environmentally friendly pure material. Manufacturers guarantee high-quality thermal insulation. PVC insulation can withstand low temperature and is not subject to deformation. You need to decide for yourself which material to choose.

When you winterize your windows, pay attention to these tips. Preparing plastic windows for the winter with your own hands is a guarantee of maximum comfort and coziness in the room. The entire premises will be switched to winter mode. Carry out the work carefully and carefully.

Don't skimp on thermal insulation materials. Don't forget to clean the surface before starting the procedure. You will be able to switch the windows to winter mode. Prepared plastic windows for the winter will not allow cold into the room.

With the onset of winter, the problem of keeping heat indoors becomes more pressing than ever, and you have to think about how to insulate your windows before the onset of cold weather. What does it even have to do with metal-plastic windows, manufactured according to the latest technologies, after some time they require additional insulation measures. It is best to do this before the first frost, since most of the building materials used negative temperature behave worse.

Washing windows as a means of insulation

Heat loss occurs not only due to drafts, but also due to significant contamination of the glass. The fact is that low level transparency leads to the fact that heat passes through the window more intensely. Therefore, in summer, dusty windows lead to an increase in the temperature in the apartment, and in winter, to a decrease.

In this regard, to preserve heat, you can simply wash the window. This should be done from the internal and outside with a cloth soaked in a solution based on ammonia or ethyl alcohol. This way, you will clean the glass from grease stains without causing unpleasant, difficult-to-remove stains.

Before insulating windows for the winter, it is necessary to thoroughly wash the frames, since the quality of adhesion of seals and insulation to a contaminated surface is much lower than to a clean surface.

Basic methods of insulating windows

Old wooden windows may have significant gaps. Moreover, even a millimeter gap between the window and the frame can result in colossal heat loss. If the window no longer closes tightly, the gap can be closed with a regular rubber seal, which is sold in any hardware store. If you carry out insulation in winter, the glue may not set well. In this case, you can melt the insulation with a fan heater or a regular hairdryer.

In addition, you can use the following simple ways insulation:

Fill the gaps between the frames and sashes with cotton wool or foam rubber, and then seal with masking tape.
Use self-adhesive foam rubber or polyethylene foam. You can buy it in the same hardware store in roll form.
Wet the white toilet paper in water, then seal all the cracks with this mixture and seal with masking tape.
Use putty or plasticine. These materials provide fairly good thermal insulation, but their separation can be quite problematic. Therefore, this method should be used only as a last resort.

These measures will not bring the desired result if you do not take care of the insulation of slopes and window sills. To do this, you need to inspect the places where the slopes adjoin the concrete and seal all large cracks with tow or polyurethane foam. After this, another layer of construction sealant should be applied.

Solving the problems of plastic windows

Few people know that even the latest double-glazed windows can provide poor thermal insulation. And people who have only recently replaced their old wooden windows with plastic ones can often observe condensation and ice on the inside of the glass. In this case, heat loss can be leveled by installing shrink film on the inside of the frame.

Insulating windows with your own hands in this way allows for minimal heat loss. In addition, this allows you to create an additional air layer between the glass and the film, which prevents the formation of condensation.

Before installing the thermal film, it is necessary to degrease and clean the frame. After this, you need to cut the material to the size of the glass, adding 2-3 cm on each side for secure fastening. Then the film is glued to the tape so that it covers the entire surface of the glass. It is very important to stick the film without bubbles and areas with a loose fit to the window. After installation, the product is heated using a household hair dryer and glued to the window. The end result will not look the best in the best possible way, but will provide warmth and dryness throughout the winter.

Lock adjustment violation

Over time, the position of the locks on plastic windows may become disturbed, thereby causing heat loss.

The lock of any plastic window consists of a moving and a fixed part. The latter is located on the frame and is an adjusting bolt. With its help, you can change the position of the wedge, which changes the tightness of the sash to the frame. This is done with a hex wrench, which can be purchased at a tool store. In the warm season, the gap can be slightly increased, but in winter it should be minimal.

Replacing the seal

Another problem with plastic windows is wear of the seal. It can be solved by a simple replacement procedure, which includes the following steps:

Closing the lock, removing the top hinge cover, lock washer and pin.
Opening the lock and releasing the door from the upper and lower hinges.
Removing the sash handle and dismantling the old seal.
Cleaning and degreasing the groove.
Installing a new seal in the prepared groove. It must be done in such a way that there is no gap between the ends of the insulation. It is also not allowed for the rubber to stick out of the groove.

To increase the service life of the seal, it must be properly cared for.

The product requires systematic cleaning and lubrication (at least once a year).

It is best to clean rubber with a fluffy cloth, after which it is advisable to degrease it with soapy water and dry it dry.

The durability of the seal largely depends on its choice. It is best to purchase a “original” product, but if this is not possible, you should contact a consultant at a hardware store who will help you choose a seal for your window. To do this, it is advisable to provide the seller with a fragment of the old insulation.

In a fairly quick period of time, plastic windows managed to take a leading position in terms of the number of their installations, since the vast majority of windows in homes and industrial buildings- these are PVC windows. In order for a plastic window to serve you for a long time, it must be maintained special care, which we will talk about.

Rules for caring for plastic windows

Caring for plastic windows is a mandatory procedure, otherwise the window will begin to lose its tightness, the fittings may fail, or the rubber seal will quickly wear out, and much more. After it has been done, it is necessary to remove the protective tape that is glued to the profile, since after a while it will be very problematic to remove it due to exposure to sunlight.

Now regarding washing plastic windows. It is necessary to wash plastic windows with special window cleaners and special napkins or rags. If any dirt appears on the profile, under no circumstances should you clean it with sharp objects: a knife, scraper, etc. To remove complex stains, use special means, to remove dirt from plastic surfaces or directly from PVC windows.

Before washing the window profile, we recommend that you first remove the layer of dirt and dust; this is best done with a brush made of soft and thick bristles. Then the window can be wiped with a napkin or rag, after applying detergent to its surface.

Preparing windows for the change of season

The fittings of plastic windows need to be adjusted 2 times a year.

How to care for plastic windows in winter

Caring for plastic windows in winter includes: washing window profile and glass, as well as switching the sash clamps to winter mode so that the sash fits more tightly to the profile when closing and does not pass through it cold air. This is done before the winter season in October-November.

How to care for plastic windows in summer

Caring for plastic windows in summer includes: washing the profile, glass and switching the clamps to summer mode so that the sash is not pressed too tightly against the profile.

Adjusting the sashes

Due to temperature changes, the window profile may narrow and expand, and because of this, the sash may begin to rub somewhere. To adjust it, use a hexagon. How to adjust the window sash is demonstrated in the picture below.

How to care for plastic window fittings

The fittings are a complex mechanism that is responsible for the movement of the sash. In order for the mechanism to work freely, it must be lubricated. machine oil. To do this, pour oil into the moving parts of the window, then move the window from one position to another several times.

Caring for plastic window seals

Proper care of plastic windows also includes care of the rubber seal of plastic windows. Please note that exactly rubber compressor provides high-quality sealing of the window profile. Like any rubber, the window seal wears out: it becomes hard and inelastic, dries out and cracks. In order for the window seal to last as long as possible, it must be cleaned and lubricated 2 times a year, as mentioned above: before starting summer season and before the start of winter.

In order to clean the window seal, it can be either removed or cleaned in this state. If you have removed the seal, place it in a container of warm, soapy water for a few minutes, and then rinse clean water and wipe with a dry cloth. Next, insert the seal into the sash and into window hole, then applying it to a rag silicone agent, treat the surface of the seal.