Usually one of the most challenging tasks cosmetic repairs- pasting walls with wallpaper in hard-to-reach places (on external and internal corners, places where pipes pass, etc.). However, if special techniques are used and suitable materials, the question is how it will be removed. Consider several ways to glue wallpaper in the corners. Let's start with a simple task - consider the technique of wallpapering even corners. And then we'll study various options work with uneven joints.

Smooth corners

Happy owners of quality overhaul, as a rule, do not have problems with warps on the walls. Wallpapering an even joint is much easier and does not require extra costs.

Internal and external (protruding) wall joints are glued in the same way. Consider the whole process step by step.

First of all, you need to decide where to start. If thin paper strips are used that will overlap each other (usually up to 0.5 mm.), Then you should start from the window (so that the seams are not visible). If the wallpaper is denser, then they will be glued end-to-end. In the second case, you should start from the door.

Decided on the direction - you can start measuring. It should be noted how many strips of wallpaper will be left on the wall before nearest corner. The fact is that the final strip should evenly lie on the adjacent wall by about 2-5 cm. It is better to cut off the excess.

With a plumb line or laser level you should outline a straight line perpendicular to the ceiling, from it and start gluing. So as you move towards the corner, the trellises will not move (tilt).

Now you need to attach the next canvas, but starting near the corner (no matter how even it may seem) is undesirable. For the same reason, an overlap of several centimeters is left on the adjacent wall. Otherwise, there is a high probability of holes and an unaesthetic appearance that will be difficult to fix.

It is necessary to smooth the glued panel at the junction of the walls very carefully. It’s not so bad if the edge of the strip that goes around the corner will protrude somewhere by 3 cm, and somewhere by all 5. It is much more important that at the junction of two walls the wallpaper fits snugly against the surface without creases, swelling and excess tension.

Advice! If during the repair you are too lazy to press the wallpaper tightly in the corners, then later the pleasant digging of holes in the sagging wallpaper will become a very exciting activity for the child.

The next strip of light paper or thin non-woven wallpaper can be glued over the spade of the previous one, focusing on a straight perpendicular line that runs as close as possible to the junction of two walls. Before you start pasting new wall, you can cut off the excess if the edge of the spade is uneven, or leave the bottom layer as it is.

Wallpaper glued end-to-end (that is, dense, not stretched after smearing with glue) in the corner is processed using the following technology:

As in the case with paper wallpaper, there is already a small width strip left after gluing the trellis on the adjacent wall. We apply glue to it, press it and carefully smooth the entire corner.

On top of this strip - spade - mount, focusing on a perpendicular line, a new wide strip. It remains to make an even joint (after all, the material is dense, perhaps embossed, overlap cannot be left).

Along the perpendicular line, using a building rule or a sufficiently long ruler, it is necessary to make a deep cut of the wallpaper from ceiling to floor. It should go through both layers, making an even edge on each side. It is most convenient to do this with a very sharp clerical or construction knife(the second one is preferable as its blade doesn't bend as much).

Now you need to carefully remove all unnecessary trimmings, re-glue the edges of the oncoming strips and straighten the joint. It should turn out perfectly even, at a distance of 1-2 cm from the corner.

Advice! Do not overlap or joint wallpaper directly in the corner. There will always be pits or cracks that ruin a smooth edge. 1-2 cm from the corner - the optimal distance, both for the internal interface of the walls, and for the external.

Several ways to align corners

Most often, both in old houses and in new buildings, there are walls with a slope. The meeting point of two such plates can somehow surprise with its shape. Unless it wraps in a spiral, and everything else is a common thing. In practice, 2 effective ways of working with uneven corners have been developed.

The first one is preliminary preparation walls by leveling (more expensive, but better), the second one does not require extra costs, allows you to stick wallpaper "as is", while it does not hide the flaws in the relief. Let's start with the first one.

If the room has rectangular shape, the junction of the two walls should have 90 degrees. If this angle changes somewhere, it means that curved walls have come to the joint. It's easy to check. It is enough to attach a square and draw from floor to ceiling, evaluating the places where the ruler does not touch the surface. If you fill in these "voids", then the output will be a perfectly even form for pasting.

Let's start with method number 1

You will need a spatula in the form of a corner (90 degrees), putty (the more diverse the relief near the walls, the more), building rights and lo, plumb or level. In the most protruding place of the corner, it is necessary to attach a spatula, mark its location with a line. Fasten to the wall along this line perpendicular to the ceiling building rule(dowels or screws). After wetting the surface with water, apply putty, and, pressing the rule to the edge, draw several times with a spatula. Smooth joint is ready. All that remains is to remove excess putty, dry and sandpaper.

Advice! If you don’t have a suitable spatula at hand, then you can use an even and dense rectangle of wood.

Method number 2

For it, you will need a plaster corner (it is a grid with an attached iron or plastic rail, bent at an angle of 90 degrees), putty or plaster. All that is needed is to attach a plaster corner along the perpendicular, evaluate the gaps. After moistening the surface, apply building mix, attach the profile, level the putty so as to hide the mesh. After drying and processing with sandpaper, it is already possible to paste over the corners with wallpaper. By the way, a similar method will help protect the joints from destruction.

Method number 3

Align the walls (respectively, the corners) with drywall sheets. This is the most expensive and effective method. If the walls do not have significant deformations, then drywall sheets can simply be glued, leveling. This is one of the most simple ways, harder - set the sheets on metal carcass. This method allows not only to level the walls, but also to improve the performance of thermal insulation, however, it reduces the area of ​​\u200b\u200bthe room.

Technique for working with uneven corners

With the help of simple rules, you can paste over the joints between the walls with trellises and without prior alignment.

Let's consider some of them:

1. The right choice of wallpaper pattern. If the corners in the room have significant deviations, it is worth buying wallpaper with a neutral coloring that does not require matching along the edges of the panel. It will be impossible to achieve a pattern match, and a skewed ornament will spoil the whole impression.
2. The choice of material by texture. One of the few types of tapestries that can stretch is non-woven wallpaper. Stretching in the process of work, elastic fabrics are able to effectively hide small depressions and bulges. In addition, they do not need to be pre-applied with glue, they do not get wet and do not tear. The strips are applied to the base dry, while the glue is applied to the walls first with a primer and only then with the main layer.
3. We glue the uneven corner in two layers. A strip of wallpaper 10 cm wide (or more, depending on the nature of the terrain) can be glued into the corner before attaching the main trellises. In case you have to make cuts in the outer layer, the lower strip will fill the resulting gap. In addition, it will help to strengthen the wallpaper in the corner from breaks in the future.
4. Instead of a narrow paper strip, the corner is often pre-glued with masking net - this also hides small depressions and strengthens the wallpaper strip in the corner.
5. Notches for a better fit. Gluing the spade (that part of the strip that goes from one wall to another, about 5 cm), it is worth making herringbone cuts in it. So the tapestries will lie more densely to the surface. The new strip is leveled and overlapped or cut through both layers, forming a joint. Thus, it is much easier to glue the wallpaper in the corners, since the cuts made will not be noticeable.

You don't have to be a jack-of-all-trades to get perfect option home interior. Enough to follow these simple rules, since the evenly glued corners of the room: without shifting the overall pattern, without swelling and distortions, are an indicator of a quality repair.

Wall decoration with wallpaper is the most popular option for decorating walls in rooms. Undoubtedly, wallpapering on even walls is quite elementary and requires only a little skill, but wallpapering the corners of a room is technically more difficult. Before sticking wallpaper with your own hands, you need to properly prepare the walls.

First you need to clean off old wallpaper or paint, apply primer to the walls and level their surface. And only then begin to paste over the corners with wallpaper.

So, repair specialists distinguish next steps this process:

1. You need to start by leveling the corners, for this you can use putty and, after it dries, clean it with sandpaper. In order for the angle to be even, you can use special device- a plastic corner that is attached to the putty. Remember that if you don't get rid of uneven surfaces wallpaper may come off.
2. The next step is to apply glue - before gluing the wallpaper into the corner of the room, you must very carefully glue the entire height of the corner with glue. If the roller does not cope with its task and leaves unsmeared fates, it is worth using a brush.
3. Direct wallpapering of corners with wallpaper - there are different lessons of specialists that help to properly wallpaper the corner of a room, it is worth listening to them, but for greater productivity, we will outline some of the features of this stage: competent finishers do not recommend gluing wallpaper in the corners with whole strips, this is due to the fact that they can distortions will appear and the joints will be uneven.
4. The wallpaper canvas must be cut so that their side from the sides extends 50 mm onto the adjacent wall.

Glue must be applied to the strip of wallpaper and the corner of the wall. Next, you need to attach the wallpaper to the corner of the wall as follows - if the pasting process starts from left to right, then left side applied to inside corner for even coverage.

At this stage, you need to clearly understand that you need to wallpaper the outer and inner corners in different ways.

outside corner

External corners can be glued in two ways: firstly, if outer corner It has flat surface, you can not waste time aligning it and immediately put wallpaper on the corner, then use the level and measure the edge of the strip so that the rest of the strips lie evenly; secondly, to glue the outer corners, you first need to lead the strip around the corner by 4-5 cm, and glue the next part of the wallpaper at the top. Using a clerical knife and a ruler, cut these layers vertically.

Inner corner

Internal corners require more attention. Wallpaper must be glued so that they go onto the adjacent surface by about 3 cm, but not more, otherwise they will go wrinkled. The fold and turn of the wallpaper must be coated with glue. Next, you need to measure the width of the wallpaper located on the adjacent wall, mark the allowance of the glued side, which is glued at a distance of about 2 cm from the corner and a vertical line is drawn through it with a plumb line - this will mark the edge of the glued wallpaper.

Alignment of the wallpaper is done by rolling, for this there are special rollers and spatulas.

All the above stages of wallpaper stickers in the corners go sequentially.

Corners on the walls on the wallpaper: what is it

plastic corners on wallpaper are a good finish for finishing corners - they have protective functions and give the corner a finished look.

Construction markets offer different decorative corners:

• Corners with a width of 20 × 20 to 50 × 50 mm are suitable for corners that are subject to heavy wear;
• Dimensions 10 × 10 or 15 × 15 mm will give a neat finished look to the wall - they are called decorative corners;
• The corners may differ in color, may have the texture of wood or metal.

For arched outer corners, it is better to use corners with the following approximate dimensions: 5 × 17.7 × 17.10 × 20 and 15 × 25 mm. Plastic corners are recommended to be mounted using silicone sealant, it is colorless and has a good grip. The length of the corners varies from 3 to 7 m, so it can be adjusted to individual sizes.

Plastic decorative corners help protect wallpaper from mechanical damage at the corners of the wall, in addition, they are not expensive and easy to install.

How to glue wallpaper in non-woven corners: features and tips

Non-woven wallpaper is particularly durable, but working with them is quite difficult, especially on corner surfaces, because. they are not elastic.

To paste over the corner of the wall with such wallpaper, when cutting off part of the wallpaper, it is necessary to make an allowance of 1.5 cm, this allowance must overlap.

You need to know a little secret - sticking non-woven wallpaper will be easier if you make equal cuts along their entire length along their edge.

Glue in this case is applied only to the wall, and the wallpaper must remain dry. In the work on decorating the corner with such wallpaper, it is better to first use the corner, then unnecessary crooked places will not appear. If the choice is made in favor of wallpaper with a pattern, in this case it is necessary to qualitatively adjust the pattern in the corners. In order to keep the pattern in the corners intact, you need to cut the next strip from the corner to fit the pattern of the already pasted wall.

Here are some tips:

• It is necessary to make a small overlap on another wall;
• It is better to hide the joints at the top of the corner;
• Wallpaper with a pattern in the corners is better to glue on a plumb line.

Meter wallpaper is a wide non-woven fabric slightly more than a meter. This type of wallpaper helps to paste over faster big apartment and pattern selection becomes easier. In order to paste meter wallpaper in the corners you need to overlap up to 3 cm on the next wall. The rest of the procedure will not differ from the standard pasting of corners, which is described above.

How to glue corners on wallpaper: installation technique

Then proceed according to the following plan:

1. The adhesion of the corners to the wall will be stronger if they are glued to the wall, and not to the wallpaper;
2. Distribute adhesive material evenly on the inside of the corner;
3. Attach and press on desired area on the wall, remove excess glue with a napkin;
4. Don't touch the corners complete drying material.
5. In order for the sealant to better grab on the site, you can fix the corner with adhesive tape.

How to glue wallpaper in the corners (video)

So, knowing the technology of wallpapering in the corners, you can perform quality repair with their own hands and in addition to help relatives in this difficult matter.

Non-woven wallpaper - a great option for finishing building material combining practicality, convenience and beauty. In the process of sticking such wallpaper Special attention you should pay attention to how to glue non-woven wallpaper in the corners evenly. Pasting with such material has a number of features that must be considered when working. For example, in order to glue a non-woven decoration, a special adhesive based on non-woven fabric is used. Also, non-woven wallpaper does not require the application of glue to the canvas itself, in addition, this species finishing material does not shrink during operation. Basically, their gluing is carried out end-to-end (with the exception of external ones).

The scheme of gluing wallpaper in the corners.

Tools and materials

So, in order to glue the non-woven decoration, the following tools and materials are needed:

• non-woven wallpaper;
• special glue;
• construction roulette;
• building level;
• simple pencil;
• metal spatula 350 mm;
• metal spatula 150 mm;
• stitching roller;
• containers for the preparation of glue, solutions;
• cutting knife;
• roller or brush for applying glue;
• plastic spatula.

How to glue inner corners with non-woven wallpaper?

Scheme of the sequence of gluing non-woven wallpaper.

It should be noted that there is one optimal and correct way that tells you how to glue corners with non-woven wallpaper. Before wall pasting inner corner should be properly prepared: old coating removed, plastering work(if necessary), the walls are leveled, primed, etc. The adhesive must be prepared according to the instructions immediately before use.

In addition, wall markings must be done: using building level a straight vertical line is marked from the edge of the inner joint at a distance equal to the width minus 1-1.5 cm. see Note that best option- this is a method in which each side of the inner corner is pasted over with a separate panel. To do this, apply glue with a roller on the marked part of the wall. The area of ​​application should correspond to the area of ​​the canvas to be glued.

You should also apply an additional layer of glue with a brush along the very edge, along the upper border of the wall and below, directly at the baseboard.

The prepared canvas (with an allowance of 1-2 cm in length) is applied, starting from the top, to the wall treated with glue, and ironed with a construction spatula in the direction from top to bottom and from the center to the edges. Thus, the excess is removed. In this case, the left or right edge of the canvas (depending on which side is pasted over) coincides with the marking line applied earlier. The excess is removed in the following way: starting from the top, close to the pasted wall, a metal spatula 350 mm long (for even walls) or 150 mm long (in the case of uneven walls), then the excess is removed with a cutting knife, while the knife blade moves along the metal plane of the spatula.

It should be noted that the blade of the cutting knife must be sharp in order to avoid defects when removing residues. The second part of the internal joint is pasted in the same way. As a result, a junction of panels is obtained along the edge. Of course, if not a corner, but another landmark is chosen as the starting point for pasting, then it is possible to paste over with a part of the canvas of the appropriate width with a deduction of 1-1.5 cm.

Trimming excess is carried out with a knife and spatula.

Joints on a horizontal surface after gluing are processed with a stitching roller.

How to glue the outer corners with non-woven wallpaper?

For pasting external corners, all of the above preparatory operations: leveling walls, preparing glue, etc. It is preferable that there is exactly a whole canvas on the outer corner. This gluing option is suitable for even external joints, which must be glued taking into account the selection of the pattern.

If the whole canvas cannot be glued during the pasting of the room, then outer corner it is pasted over with a wallpaper cloth so that the overlap is 1.5-2 cm. The other side is pasted over with a whole cloth, while the edge of the cloth is glued to the edge. This option is most preferable if the material is intended for painting, which will hide pasting defects. However, this option is not suitable for wallpapers that need to be glued taking into account the selection of the pattern.

Usage roll materials for facing surfaces - this is a popular and sought-after solution that allows you to achieve high-quality results in a short time. But the finishing technology has some nuances. It is especially difficult to glue wallpaper in the corners: the resulting coating must be free of distortions and defects. The most suitable method is selected depending on the situation.

Existing varieties have a certain order of wall cladding, which allows you to achieve the best result.

Vinyl

The technology for working with this option is not very difficult if you perform all the processes correctly.

Step-by-step instruction:

1. The place is being prepared. For convenience, the material is rolled out on a clean floor or a table of a suitable size with a pattern down.
2. Trimming is carried out taking into account the allowance of 100 mm. If the coating has a complex pattern, then the scheme specified by the manufacturer is used.
3. The canvas is treated with glue and folded in half for better penetration.
4. The composition is applied to the wall with the capture of areas that extend beyond the width of the roll.
5. The strip is laid on the base and smoothed out well.
6. It is taken into account that standard and meter vinyl wallpapers on a non-woven base, you can only glue it end-to-end, the overlap will ruin the look.

The vinyl layer on the canvas is strong enough, so the wallpaper can be safely smoothed out with a wallpaper spatula without fear of damaging the integrity.

On a note! In the absence of experience and the need to adjust a complex pattern, it is better to prepare: for this, the strips are placed on a horizontal surface, aligned with each other and the size of the necessary adjustment is noted.

Paper

Sticking this variety is rarely accompanied by difficulties. For the process, you can use any glue, including those prepared by yourself.

Action algorithm:

1. According to the width of the roll, marking is carried out using a level and a plumb line.
2. The material is dissolved into strips, depending on the pattern. For this, a technology similar to working with a vinyl version is used.
3. The canvases are well smeared with the prepared composition and rolled up.
4. After surface treatment, pasting is carried out. The excess is cut off.
5. Often paper products are overlapped, but strips can also be joined. It is taken into account that after drying the canvas will become narrower, so a special paper tape. This rule applies to other types of wallpaper as well.

It is impossible to tighten the web at the junction by force, the connection is leveled exclusively with a rubber roller

All processes, especially smoothing, are carried out with care, because even multi-layer products are very easily damaged.

non-woven

To glue this variety, use special variant glue, because the material is quite heavy. Training binder composition performed strictly according to the instructions and applied only to the wall.

Process diagram:

It is important to properly impregnate the base: do not leave dry areas. Be sure to affect places that go beyond the width of the canvas.

Advice! To speed up the process, it is better to apply the composition with a roller.

In addition, we suggest watching a video where the process of gluing non-woven wallpaper is considered.

How to properly wallpaper corners

The technology of laying sheets on the outer and inner corners has differences.

External

These areas are the most visible, so they must be glued with special care. The easiest way is if the angle is perfectly even, but this is quite rare.

In the presence of defects, the process is complicated. If the corner is littered, then it will be necessary to trim the canvas along the bend line in order to impose one section on the adjacent one. This method is not suitable for varieties with complex patterns.

There is another way:

1. The strip is glued to a section of the wall.
2. Using a special spatula, the material is carefully smoothed under the existing bend, a transition is formed.
3. If required, part of the laid canvas is torn off, after which the excess is driven up or down. There must be a margin on both sides.
4. To adjust the pattern in case of skew, the next strip is overlapped until the pattern is aligned with an indent from the edge of 5–10 centimeters.
5. With the help of a ruler, which serves as an emphasis, the superimposed canvases are cut exactly according to the pattern.
6. If required, the joined sections are additionally coated with the composition.

Docking the outer corner with trimming on one of the adjacent planes is considered the most effective way arrangement

This method does not completely correct the skew, but facilitates further sticker and fitting.

Interior

The technology for working with such a site is almost identical to the previous process, but has some nuances:

1. All sides are well processed wallpaper paste. If the composition is also applied to the canvases, the impregnation must also be sufficiently thorough.
2. Laying begins with the wall from which the movement is carried out. The first fragment is aligned with the previous one, smoothing into a corner is carefully performed. To do this, with a rubber spatula, the waves are driven in one direction.
3. The part that falls on the adjacent wall is slightly pressed.
4. The next steps depend on the situation. Most often, it is required to cut off the existing bends in the middle and put the excess on top of each other.
5. To achieve better alignment, the edges are shortened and smeared, after which the segment is located on the main part of the canvas.

Technically, the docking of the inner corner is not much different from similar works on external structures, but this process is considered easier, since internal corners are visually less noticeable

This technology makes it possible to glue different types products, but if the corner does not involve cutting, laying is carried out in a standard way. To do this, the joint of both sides is carried out with a margin in order to level the unevenness by fitting and trimming at the place of alignment. This will take longer, but will get rid of the overlap in the corner.

Video tutorial: how to glue wallpaper with trimming in the corners

Docking wallpaper with a pattern

Work technology:

1. The strip is laid on the initial part of the wall and gradually distributed over the surface. Waves are driven towards the corner.
2. The material is carefully fixed on the inner fragment and smoothed from top to bottom. It is taken into account that the canvas should be cut off with a significant margin, since trimming of the lower and opposite edges will be required.
3. The part that falls on perpendicular wall. The areas at the skirting boards are adjusted.
4. If the side is uneven, then it must be pasted over with the next strip lying completely in vertical plane. The offset must affect the matching pattern.
5. A ruler is set exactly along the line, with the help of a clerical knife, the excess is cut off.
6. The second strip moves to the corner, the gap needs to be additionally glued.

If there are no problems, you can dock directly along the inner corner, but this will require a certain level of skill.

Wallpapers with a pattern are joined according to the same principles as without a pattern, but if a horizontal mark from masking tape, then it will be easier to combine the ornament

What to do if the joints are crooked

Perfectly even corners in rooms are rare, so to eliminate different problems you can use the recommendation that many designers use - a combination. It is necessary to seal the transition from wall to wall with wallpaper with a pattern or with bright colors. Part of the pattern should go to the adjacent side, where it is cut at a right angle and combined with a solid material. The docking line will turn out to be even, and the existing shortcomings will not be evident.

July 11, 2017
Specialization: facade finishing, interior decoration, construction of dachas, garages. The experience of an amateur gardener and horticulturist. He also has experience repairing cars and motorcycles. Hobbies: playing the guitar and much more, for which there is not enough time :)

The most common beginner mistakes

First of all, let's look at how to glue wallpaper is not necessary. The most common mistakes newbies make are:

• Poorly prepared surface. The level of complexity of pasting the joint of planes depends on their quality. If the apartment has crooked corners, then it will not be easy even for a specialist to complete the finish with high quality.
  Of course, it is not always possible to make the wall joints ideal, strictly at 90 degrees, but there should be no deviations from the vertical. Therefore, spare no time and effort to prepare the surface - putty the walls or even plaster;

Quickly and easily align the outer joints of the walls will help plaster corners. During installation, they are leveled, after which they are glued with plaster or putty. The price of corners starts from 30 rubles per 2 meters.

• Wallpaper cutting. As a result of such a decision, the edges of the canvases may diverge, or vice versa - unevenly overlap each other, respectively, the gluing looks messy. Therefore, according to the technology, it is necessary to provide a small inversion to the adjacent plane.

The exception is paper sheets that can be cut vertically. The only thing, in this case, you first need to stick on the joint of the walls pinstripe wallpaper in case the joints come apart;

• Big twist. If the joints of the walls are even, then such a mistake is not terrible, but in crooked corners a large inversion will cause the strip to deviate from the vertical. As a result, all subsequent canvases will be pasted crookedly;

• The sheets are not fully glued. When gluing the canvas, many beginners do not push it all the way, as a result of which small plot, located opposite the inner corner, hangs in the air. This leads to the fact that over time the coating begins to peel off and even tear;
• Glue applied poorly. If wallpaper is glued on a non-woven base, then the glue is applied to the surface of the walls, and not to the canvas. In this case, the mistake is to work with a roller, which does not always allow you to completely lubricate hard-to-reach places.

Beginners are often interested in - from what angle to start gluing wallpaper? If they are all even, then it does not matter where you start gluing. Otherwise, start gluing from an even angle to avoid warping the strips on the walls.

Sticking technology

As you know, there are two types of angles:

Each of their types requires its own approach when pasting, therefore, further, we will separately consider the process of pasting wallpaper on external and internal corners.

Internal

The sticker instructions are as follows:

Illustrations	Description of actions
	Surface preparation. Beginners often prime the walls with their own hands only with a roller, however, as in the case of glue, it is difficult to process corners with this tool. Therefore, after priming the walls, be sure to “walk” along hard-to-reach places brush.
	Applying glue. If non-woven wallpaper is glued, as mentioned above, the glue is applied to the walls, not the canvas.
	Gluing. The canvas must be cut in width so that the twist on the adjacent wall is about one and a half centimeters. AT uneven corners inversion can be increased up to 5 cm; If you are gluing meter-long non-woven wallpaper, and you had to cut off a wide piece of the strip, you can start pasting the adjacent wall from it, if, of course, the pattern allows. Then you should push the canvas with a spatula so that it fits snugly against the walls; If folds appear, the edge must be cut across, i.e. towards the crease. The strips on the adjacent wall must be overlapped with the edge. In this case, the canvas is aligned along the markup (vertical line), and not the edge itself.

This completes the sticker.

outdoor

Now consider how to stick this finishing material at the outer joints of the walls:

Illustrations	Description of actions
	Surface preparation. As in the previous case, the surface must be primed and glue applied if the vinyl sheets are non-woven.
	Bonding: Position the strip so that it extends 30 centimeters onto the adjacent wall; If the edge begins to wrinkle, cut it along so that the twist is no more than 5-10 mm. If the wallpaper is patterned, with such a small twist, you may need to trim the edge of the second canvas to match the pattern.

Many people are interested - how to protect the wallpaper on the outer corners? For these purposes, there are special decorative corners that are glued on top of the finish.