Even if the pond on your site is small, it can make a good contribution to the improvement of your territory. And if you decide to build a fountain with your own hands, it will be interesting. This will not only be a place for leisure, but you will also receive a mountain of praise from friends, acquaintances and neighbors.

However, not everyone wants to take on such an idea, because they think that the construction of such hydraulic device very expensive and labor-intensive, and also requires specialist intervention. If you want to know how to make a fountain at home, then we want to please you that anyone can afford to build a fountain with their own hands at home, you just need to know all the aspects of design and construction. In this article we will look at how to make a fountain.

Types of fountains

Due to the type of construction, products are divided into two types:

1. Open fountain. As a rule, in such buildings water is supplied to a nozzle. The jet is formed due to the fact that there are differences in water levels. Here you need to monitor the water level, and the water quickly becomes dirty. In order to create such a pressure, you need to raise the container a meter from the nozzle.
2. Pumping fountain. This is the most common design option. Here the pump is placed on the bottom, creating a constant water cycle. In structures of this type, the pressure is quite strong and visually looks more beautiful.

Multi-level fountain

Based on the type of pump, fountains are divided into submersible and stationary.

1. Submersible pump. It is placed at the bottom of the pond. With the help of a pipeline, water rises to the surface, and the nozzle creates a certain form flow. In this version, water seems to erupt from the ground.
2. A stationary fountain is usually built from stones in the form of a figure, the shape of which can be any to your taste. Such structures are installed in a park or square, as they are a kind of art.

Ideas for a fountain (video)

Where to install the fountain

When choosing optimal location for construction, it is important to take into account such a factor as the slope of the ground. If the surface on the site is uneven, then it is better to install the structure at the bottom. This will make it easier to adjust the volume groundwater, and the oxygen saturation of the air will also increase.

Install the fountain where it will be convenient to admire it

It is not recommended to build a fountain:

1. Close to home, because strong wind water will fall on the house itself.
2. In an area with direct sunlight, which will contribute to the rapid flowering of water.
3. Under a tree, as fallen leaves or overgrown roots can damage the product.

The fountain must be placed so that it does not interfere with movement around the yard, but on the other hand, so that it can be clearly seen from different sides. We advise you to place it near the place of leisure.

The smallest distance that should be between the structure itself and green spaces is 0.5 m. Thus, the plants will be protected from large quantity moisture. The same principle applies to furniture near a water feature. The most optimal location structures - a place in the shade and without wind, near water and electrical network. This will save you effort and material costs.

After we have decided where the fountain will be, we can begin its construction or what the shape and depth of the building will be

Construction materials

To save money and power costs, it is possible to build a pond with a pump placed in it.

Materials for building a fountain:

1. Capacity
2. Pump
3. Water insulator
4. Shovel
5. Stone different sizes
6. Decor elements

How to select and install a container

In the case of a small fountain, a regular small basin can serve as a reservoir.

For a larger option, you can use a bathtub or a pit dug by yourself. When using a bathtub, you need to dig a hole so that its edges are below ground level. First, all the holes in the container are closed, then it goes down into the hole, where it needs to be strengthened with stones and earth.

If you want to dig your tank, use film for this. It, in turn, must be dense and of high quality. In a dug hole, the film is pressed against stones. Stones also line the bottom. They should not be sharp, as this may damage the film. They need to be distributed equally over the entire bottom.

How to choose a pump

To build a fountain, it is not necessary to buy expensive materials, since you can use elements used on the farm. But you don’t need to save on buying a pump, since the quality of the pump determines how long it will work without problems, and the more beautiful the end result will be.

Most optimal choice for the construction is use submersible pump. But if you have a large or cascading fountain, installing surface pump

The main indicator when buying a pump is its power. If the water pressure in your fountain is low, then you do not need to buy a powerful pump. It is important to know that the power corresponds to the diameter of the pipe, and the pressure must be strong, otherwise it will be the result of an unsuccessful fountain.

Construction of a fountain

The construction of the fountain consists of five stages:

1. Digging a pit
2. Strengthening the trench
3. Securing the tank or installing the film
4. Pump installation
5. Fountain decor

Now let's look at some options for building a fountain with your own hands.

Examples of fountain construction

Using a tire

For this we will need

1. An old used tire, for example from a tractor
2. Cement, water, crushed stone and sand
3. Concrete mixing tool
4. Film
5. Level
6. Stones of various sizes
7. Mastic or silicone
8. Pump

Tire fountain covered with stones

Sequencing:

1. Preparing concrete solution.
2. Pour the solution onto the bottom 10 cm high and level it using a level.
3. After the solution has dried, place the tire on the bottom, having previously cut off the sidewall on one side.
4. Using mastic or silicone, glue the tire to the base.
5. Concrete is poured along the edge of the tire, thereby strengthening the structure.
6. Place the pump in the center of the tire.
7. We decorate the fountain. Using a tire

Using film

For this type of fountain you will need:

1. Thick film
2. Shovel
3. Sand
4. Pump
5. Stones of different sizes

Fountain in a pond made of film

Sequencing:

• First, you need to dig a pit, remove everything unnecessary from the hole, for example, stones, and tamp the bottom.
• Next you need to fill the pit with sand.
• The next thing to do is lay down the film. We lay it so that the edge extends beyond the hole. Then we press the film with stones along the contour of the pond.
• Then we install the pump depending on its type and instructions.
• We decorate the almost completed work of art to suit your taste.
• We fill the pond with water.

Using an old bathtub

For this case, you need to have in stock:

1. Shovel
2. Stones
3. Pump
4. Bath
5. Insulation tape
6. Metal scissors
7. Metal sheet
8. Drill

Fountain from old bath

Sequencing:

1. We dig a hole according to the size of the bathtub.
2. We lower the bathtub into the hole and plug all the holes.
3. You need to cut wide strips from a sheet of metal and lay them around the perimeter of the bathtub, pressing it down with stones.
4. You can place decorative crushed stone in the bath itself.
5. We install the pumping system.
6. It is possible to install a backlight and change the color of the water using blue. Thanks to this, the bath will not be noticeable.
7. We decorate our design.

Using a plastic bottle

For such a fountain, so to speak, you need to have:

1. Plastic bottle
2. Gvozdik
3. Insulating tape
4. garden hose

Practicality in everything!

Sequencing:

1. Remove all stickers from the bottle.
2. Punch holes in the bottle with a hot nail.
3. We install the hose in the bottle and wrap it tightly with tape.
4. We place our structure in the planned location and turn on the pressure.

This mini fountain is suitable for watering your vegetable garden.

Home Decorative Fountain

For this we need:

1. Flower pot
2. Glass paint
3. water pump
4. Outlines
5. Decoration for aquarium

Fountain from a flower pot

Sequencing:

1. We paint the pot with paints.
2. Make a small hole at the bottom of the pot.
3. We mount a pump under the pot stand.
4. We pass the tube through the hole made.
5. We put pebbles on the bottom.
6. We make decoration.
7. Fill the container with water.

Decor

Decorating your fountain will further highlight how unique it is. You can put it next to the pond natural stones, you can even different colors, display indoor plants, put up various figures of toys or animals, etc.

Illumination of the structure can amaze your guests with its originality. This is done using special equipment. Lamps are placed around the perimeter of the structure, and lighting is installed at the bottom.

Plants and decor for the fountain

At the bottom of the reservoir you can place aquatic plants, and plant shrubs around it.

Fountain care

After you make a fountain at home, it will, of course, need to be well looked after. In order for order to be maintained, the water to be clear, and the building to have a pleasant appearance, it is important to constantly clean the container. Using special devices, you can remove leaves and similar things from the pond that can spoil the water and also damage the equipment.

When summer season ends, you will need to drain the water from the reservoir, remove the equipment into the room, and cover the rest with oilcloth to protect it from dirt.

Making a fountain with your own hands on a summer cottage or in your apartment is not so difficult and does not require large material expenditures. Before erecting a structure, you need to find out what its shape, size and location will be. You can place it anywhere - in your garden or near the gazebo. Subsequently, the fountain needs to be well looked after - monitor the cleanliness and water level, and also remove fallen leaves.

This type of structure is often installed in summer cottages. A fountain can decorate any free area or become its oasis. If you use your imagination and use various elements decor, the fountain will look even better and more original.

How to install a fountain in your garden (video)

Who said that a fountain is exclusively an outdoor fixture? Modern decorations of this type are used with equal success both outside the house and indoors - it all depends on the size and design. For apartments and houses, as a rule, small fountains are used, which are called “home fountain”. It’s about them, or rather about their variants self-made, will be discussed in this article.

A person can contemplate three things for a long time: for a long time he is unable to take his eyes off the flame, flowing water and on how someone else works. It is for this reason that the most common decorations in houses and apartments are all kinds of fireplaces and fountains. In this article we will talk about fountains - together with the Dream House website we will deal with the question of how to make a home fountain with your own hands? We'll consider various options self-production of this decor and, most importantly, we will understand the principle of creating such things, knowledge of which will allow you to independently design these products at home.

Do-it-yourself home mini fountain photo

Home fountain: how it works

Most of you will probably be surprised at how simple a fountain is - one might even say that by the standards of modern technologies This is an elementary thing that does not cause any difficulties in manufacturing. If you understand its design, then it can only be divided into several individual parts. Plus or minus, of course, since there is no limit to perfection, and it can be improved, as they say, ad infinitum.

As for the operating principle of such devices, there is nothing special to understand - the movement of the liquid simply loops. There is a container from which the pump pumps out water and supplies it to the nozzles of the fountain - flying out in the form of a beautiful decorative stream or flowing down like a waterfall, it returns back to the same container, from which, again, it is sucked in by the pump and sent to the next annular cycle. This is the whole fountain.

How to make a fountain at home: options

Among the most common options for making home fountains with your own hands, you can highlight just a couple more or less successful designs. To be frank, only one is completely successful - the first variation, although acceptable for a house or apartment, still has several significant drawbacks.

Depending on the required sizes, you can also install intermediate containers - create a so-called cascade of waterfalls, which will look much more attractive. The principle of manufacturing such fountains is no different from a single waterfall - the only thing that is added here is one or more intermediate containers. In such a situation, water is supplied by a pump to the upper container, from where it flows by gravity into a reservoir located just below. In turn, water will flow from this reservoir into a container located below - with this approach to business, the number of containers can be unlimited.

Home fountain photo

How to make a home fountain with your own hands: installation without a pump

Let me make a reservation right away that this is not a perpetual motion machine, and such a fountain will not be able to work indefinitely - this is an excellent toy that clearly demonstrates the work of the laws of physics and nothing more. Depending on the containers used in the design of such a fountain, you can count on 10, 15 minutes, perhaps even half an hour of operating time - then you will need to recharge, which you will get tired of doing in the very near future.

We are talking about, for the operation of which three containers are required, connected in series to each other by tubes - this is a completely sealed system that works thanks to air lock. From the receiving bowl, water flows into the lowest, and most importantly, empty container - it presses on the air in it, which, in turn, creates pressure in the upper container (it contains water). It is this pressure that causes the water to rise like a fountain. What is most interesting is that the rise of the jet can be quite large and reach 1 m in height. Moreover, this fountain can even be somewhat “automated” - organize its recharging with less time and effort. Undoubtedly, this is a noteworthy invention of mankind, which is worth devoting a separate article to, which we will do in the future.

How to make a home fountain with your own hands: Heron's fountain photo

In conclusion to the topic of how to make a home fountain, a few words about very attractive additions that will allow you to contemplate not only the appearance of flowing water, but also observe various effects. The very first thing that comes to mind here is . You can organize it different ways, but the most interesting of them is the use of a small electrical generator. A small device bought in a store is quite capable of making the LEDs glow - you can place them as you like and anywhere, the main thing is not to forget that water and electricity are incompatible things in principle.

The modern rhythm of life, created by people, tires them and exhausts them nervous system constantly experiencing stress. Daytime overexertion often leads to sleep problems, and in the fight against this trouble a small indoor fountain becomes our reliable ally.

The main advantages of decorative home fountains are aesthetic pleasure and air humidification. If there is a small fountain in the room, then there is no need for an air humidifier, and besides, the “fountain” method of humidifying the atmosphere looks more natural. If this fountain is quite large, then it will easily create the most comfortable microclimate in the home for all its inhabitants: people, plants and animals.

Selecting a fountain for the interior

When choosing a decorative home fountain, you should take into account the size of the room. IN spacious room small desktop version the fountain can simply get lost, but floor mini fountains for an apartment with a bowl more than a meter in diameter, they will certainly become one of the centers of attention in the entire room - they will sufficiently humidify and refresh the air. It is also effective in the interior of an apartment if there is a sufficiently large free space look artificial wall compositions , which are a decorative drip or thread-like fountain. True, we should not forget that when arranging wall fountains, heavy building materials are used, such as cast iron and stone, so such decorations can only be started against a strong and reliable wall.

Depending on the interior of the room, you need to choose the material of the fountain, which is usually glass or artificial stone. In a room decorated in minimalist or hi-tech style, fits in perfectly stele, shrouded in a film of falling water (the so-called “ wet wall"), especially considering the fact that occupies one of the main roles.

To the bedroom it is best to find small decorative tabletop fountains and waterfalls, in evening time capable of serving as an exquisite night light. Tabletop fountains with lighting are especially valued - dim light combined with the quiet murmur of water will become best background for going to bed (especially for children). As you can see, in these cases we can already talk about a therapeutic effect decorative fountain, and, therefore, his functionality are expanding even more. And if you buy a fountain model in St. Petersburg not only with illumination, but also with fog, you will provide your bedroom not only with additional decor, but also with an element that creates an intimate atmosphere.

An ideal sculpture would be one depicting grotto, waterfall or water mill. Typically, waterfalls sold for such premises are equipped with flower pots where you can plant live plants, as well as lighting and an additional humidifier. A niche under the stairs, by the way, can also be a very suitable place for installing a “mountain waterfall” there.

If you have a question about where to buy a fountain for your home, contact the World Wide Web - the search engine will probably give you several addresses of the stores closest to you or show you on which sites you can order these fountains. But at the same time, if you are planning to buy home fountains in an online store, ask how noisy its pump is. Usually pump power directly affects the noise level of the structure , so you shouldn’t chase too powerful options. The sound of the water should prevail over the sound of the pump running.

Fountain lighting

Even the most trivial fountain can be made magical if you apply lighting to it, which can be different:

Using underwater lighting arises Effect glowing water . If at the same time you want to make a floor fountain for your home with lighting with your own hands so that it turns out to be a real holiday extravaganza, then you need lighting, rotating using a special mechanism. A very important aspect of underwater lighting equipment is laying the wires in a waterproof busbar. For greater safety, it should be equipped with an automatic circuit breaker that trips when current leaks. According to safety requirements, only 12-volt lamps can be used for underwater lighting: halogen, fiber optic or LED, connected via a transformer.

For water surface lighting It is better to place the lamps above the water along the perimeter . To emphasize an individual element of the composition, a beam of directional light is used. Spotlight you can draw attention to one detail.

Varieties of unusual indoor fountains

Fountains-pictures

Water elements, which are indoor decorative fountains for apartments in the form of paintings, look very unusual and interesting. For example, the painting depicts a landscape with a waterfall, and the entire landscape, as usual, is painted, but the water in the waterfall is real. At the same time, the design of the fountain is such that the water does not fall on the floor at all, but is captured by a special drain built into the frame, from where it returns to the tank, closing the cycle. You can buy a decorative fountain-picture in almost any souvenir shop - today they are in great demand, so sellers strive to keep up with fashion and provide the buyer with all the latest in interior design.

Fountain "wet wall"

An aqua interior can be created not only with traditional indoor tabletop fountains, but also with more unusual means. One of these techniques is the fountain " wet wall": on a wall lined with ceramics, stone or waterproof mosaic, water flows at different speeds drops, trickles, and finally streams of water. A waterproof drainage device is placed in the floor, from which water returns to the top. A variety of modes of water supply, lighting and wall covering allows you to obtain numerous transitions and effects. Such a wall of water amazes, shocks, makes you dumbfounded, but will not leave anyone indifferent. Of course, the price of floor-mounted indoor fountains and waterfalls may be prohibitively high for people of average income, and only wealthy people can afford to buy an indoor fountain of a similar design and scale. However, do not despair - we will tell you how to make an indoor fountain with your own hands, and you will understand that it is not so difficult, and such a miracle can be made with your own hands using ordinary materials.

The floor version of an indoor fountain can be surrounded indoor plants, for which it will create a favorable microclimate. If you use special settings in a decorative fountain, you can achieve a fog effect.

Fountain curtain

No less stunning is the effect of the curtain fountain, through which water flows down in a wide stream. The picture gives the impression solid water wall , which flows down the glass. If such a system is placed in doorway By equipping it with motion sensors, you can get a kind of water door separating the rooms. When a person approaches, the sensor blocks the flow, and the passage is free. Carefully thought out illumination of such a fountain will turn your apartment into a fairy-tale palace.

There are varieties of decorative home fountains depicting water columns : along special fishing line strings, water flows down from ceiling lamp continuous flow, which forms a hollow, transparent water column inside. In cross-section, such a pillar can represent a circle or a polyhedron. Often a sculpture or decorative tree. You are unlikely to be able to buy interior fountains of this design in ordinary souvenir shops, since such impressive decorative elements are often made to order.

DIY indoor fountains

A miniature fountain can unusually enliven any interior. You can even build it with my own hands, but for this you need, of course, to understand its design and think through a work plan. Knowing how to make a decorative indoor fountain with your own hands, you will save money on buying new decor, but ensure yourself a great mood for many years.

Step-by-step process for creating an indoor fountain

For this work you will need:

• Container for the future fountain.
• Aquarium pump.
• A piece of hose for cleaning an aquarium.
• Large sea shell.
• Expanded clay, shells, decorative colored primer.
• Waterproof glue.

You can choose any vessel you like as a fountain bowl, even flower pot. The main thing is that the vessel is reliable and water does not leak out of it. A pump that lifts water upward and creates a stream will be required with a sprinkler, but without a tip, taking into account the small size of the fountain bowl.

The procedure for making a fountain:

If you first learned about how to make a fountain with your own hands, then you should understand that the work is quite painstaking and creative, but its result will not only significantly decorate your interior, but will also be a source of pride in front of your admiring guests.

Decorative fountain from a flower pot

There are a huge number of master classes showing what decorative things can be made from ordinary flower pot. But today we will tell you how to make a home fountain with your own hands from the same flower pot. If you want to make a larger fountain, take large capacity, but if your plans include a small tabletop fountain, a flower pot 20-25 cm in diameter will be enough.

To make a fountain at home, you will need the following materials:

Progress

• A flower pot is needed as a bowl for a fountain; it can be painted with special paints if desired.
• Under the pan you need to install a pump that will circulate water, and you need to make a small hole in the bottom for drainage.
• A pump tube is passed through the hole, and decorative stones are poured onto the bottom.
• The entire structure is assembled and filled with water. Aquarium plants can liven up the appearance.

According to this scheme, anyone can build a miniature fountain with their own hands - all you need is desire and imagination.

We make an indoor fountain without a pump

Independent arrangement own apartment or summer cottages are preferred by many people. And sometimes, to add special elegance to the interior, the owners think about how to make a fountain without a pump, since not everyone is “friendly” with electrical appliances and their connections. You can, of course, make a decorative imitation of a fountain, for example, from paper or plasticine, but in this case you will not hear the soothing murmur real water. A small fountain can be made from a bottle or from plastic containers that are more suitable for the designed design, but you need to remember school curriculum in physics.

In order to make a mini fountain with your own hands without a pump, will be required following materials : three plastic containers, tubes, tools, adapter, sealant and decorative elements (you can come up with a composition made of stone and artificial flowers, or you can limit yourself to just one thing).

Miniature preferences

Determine the dimensions of the future product, but do not strive for gigantism. After all, a large fountain will definitely need a pump, but this is not our case. It is better to make a preliminary sketch of the fountain. If your imagination fails you, look at what a do-it-yourself fountain could look like in a photo or video - this way you will have an idea of ​​what kind final version pursuit.

Let's remember physics

It is best to base the design principle of communicating vessels , a friend from school physics. If two vessels connected by a tube are placed on different heights, then water will flow from the upper one to the lower one. But this simple system It’s better to modernize it a little: install both vessels at the same level, connecting them with a pair of tubes. The tubes are connected to a “T”-shaped adapter. If you pour water into the vessels from above, the fountain starts working.

We work with two identical vessels

Pick a pair of exactly identical vessels, preferably plastic ones. Then you will need as thin a tube as possible. Moreover, the thinner it is, the longer the fountain will function. A tube from a kitchen filter may work just fine. Holes are carefully drilled in the bottoms of the vessels, which are slightly smaller in diameter than the taken tubes. The tubes should be inserted into the holes (this happens with some interference). Then it is better to treat these places cold welding or other sealant to prevent water leaks.

The third vessel is the final one

Next, you need to move to the third vessel, the volume of which is equal to the sum of the volumes of the other two vessels or even more - so that the water poured out of them completely fits into it. Exactly in the middle of the bottom of a large vessel you need to install a “T”-shaped adapter, and holes need to be drilled in the walls of the vessel near the very bottom. Two tubes are passed through them, coming from the vessels located above. These areas should also be securely sealed. This completes the installation of the main structure of the fountain.

Installing an indoor fountain

Next, you need to install the fountain in the designated place. In this case, it is necessary to do this so that the upper vessels are located not only above the large one, but are themselves at the same level. For home use, the receiver container of an indoor fountain must be removable so that the water from it can be returned to the upper vessels. And, of course, such a fountain needs to be decorated, relying mainly on your own imagination.

Regardless of the fountain you choose, you will quickly fall in love with it for its vibrant streams of water and its calming effect on all the inhabitants of the house.

For those who want to update the exterior, make it special and memorable, we suggest using a small homemade fountain. Step-by-step instruction Making a fountain with your own hands is quite simple and anyone who has a certain set of tools and materials can create this beauty in their yard.

Installing a fountain at the dacha

The first point of the fountain installation plan is planning its size and type. Consider the size of the yard; do not make the fountain too large or small - this will not give a positive effect. visual effect. Remember, the power of pumping equipment is directly proportional to the size of the structure.

Now you should select correct area land for installation. Firstly, the fountain should be located where it can be clearly seen. Secondly, it should be close to the vacation spot. The sound of running water and cool freshness in summer heat- important components of a pleasant and peaceful holiday on fresh air. Try not to install the fountain in direct sunlight. The water will have to be changed frequently due to blooms. There is also no place for structures near trees; the roots can damage the thicket and for repairs you will have to dismantle the entire decorative element.

To install a fountain with your own hands on the site correctly, do not choose places near the walls. In this case, the structure will not avoid exposure to mold and mildew. And this, in turn, will not only spoil the appearance, but also cause an unpleasant musty smell.

Plan future buildings on the site in advance. You should not install a fountain on the road to them.

Step-by-step guide for installing a fountain in your country house with your own hands

Let's talk about how to make a fountain with your own hands using the example of a very simple design - fountain-fontanel. A structure of this type has a number of advantages:

• Spectacular appearance;
• Easy care;
• Easy access to parts for repair purposes;
• Possibility of dismantling for winter.

Having selected a place for installation, we dig foundation pit slightly larger than a fountain bowl. Additionally, a shallow hole should be dug around it. gutter(about 10 cm).

DIY fountain. Instructions in photo

At the bottom of the pit there should be sand cushion 15 cm thick. This will protect the underground part of the structure from plant roots. Level the surface and install it on it plastic bowl. We level the font, pour in and compact sand. The container should be installed in such a way that its edges protrude by 5-8 cm.

The next stage is filling plastic container under a bowl of water. There is no need to pour “heaping”; leave 4-6 cm to the edge.

Now it is necessary install a fountain and check the operation of pumping equipment. If power pumps can be adjusted, then we adjust it so that the water falls back into the bowl. The choice of equipment should be approached very carefully. Ideally, when purchasing, explain to the seller what bowl size and bowl volume is expected. Then he will help you choose equipment of the required power.

DIY fountain. Instructions in photo

After installing the bowl and pump, you need to do waterproofing fabric. We cut out a canvas with a diameter the size of a fountain pit. Starting from its center, cut strips. This must be done so that the diameter of the resulting inner circle is equal to the diameter of the structure’s bowl. We bend the resulting strips of material and lower them into the container. They can be secured using sealant. Do-it-yourself fountains always require a lot of patience and accuracy in work, especially this stage of construction.

To ensure that the base of the structure does not lose its shape and is stable, we place a couple of rods on a sealed fabric fittings, and on top of them - galvanized fine mesh. The mesh size will influence the size of stones or crushed stones used used in the decor of the fountain.

DIY fountain. Instructions in photo

The final stage of construction - decoration designs. The border of the fountain can be laid out with larger stones, but you should not make it too clear. Small stones such as sea pebbles or crushed stone are laid out on the mesh. If it is necessary to add naturalness to the fountain, then its boundaries should not be too clear. Various plants will look good along the edges of the structure.
Thematic japanese fountainfor lovers of oriental exoticism it is installed in a similar way. Step-by-step instructions for making a fountain with your own hands for the garden in Japanese style consists of the same points. You will find a diagram of the structure below.

DIY waterfall fountain

We will not build anything grandiose, but small, about 1 m high, cascading waterfall We are quite capable. It has already been described in detail above how to prepare a pit for a pond bowl. But this time we are building a waterfall. And if there is no natural elevation for him, he will have to create it himself.

Do embankment convenient in the process of digging a pit. We simply throw the earth where the slide should be and carefully compact it. For the hose supplying water to the point where the water falls, make a small groove There are holes and embankments in the wall.

DIY waterfall fountain. Instructions in photo

After the foundation pit and embankment for the waterfall are ready, we begin to cover the bottom and walls of the mini-pond waterproofing material (for example, PVC film). The fabric must be laid in such a way that it not only completely covers the bottom and walls of the pit, but also protrudes about half a meter on the sides of the pit.

Be sure to lay a pipe for supplying water to the top of the waterfall in a previously prepared channel-ditch. Bend one edge 30-40 cm up.

This time we are making a permanent structure, and therefore it is best concrete a bowl of a pond. To begin, carefully lay out metal mesh at the bottom of the pit. The waterproofing must not be allowed to become damaged. Next, pour a layer of concrete about 12-15 cm thick.

How to make a fountain at your dacha with your own hands. Photo

Now you need to prepare bowl walls. We lay out the mesh, strengthening it in the solution that has not yet hardened. You can continue installing a fountain with a pump with your own hands, which will look like a cascading waterfall, within a day. We fill the walls of the pond bowl and finish the most difficult stage of construction.

The next part of the construction is decoration the resulting structure. We build steps on a pre-compacted slide. The step should be about 30 cm and three ledges will be enough.

On the resulting flat surfaces we post it flat sandstone, pebbles or any other material to your taste. We decorate the rest of the fountain, including the film around the perimeter, with stones, crushed stone, marble or other pre-prepared materials.

All that remains is to turn on the pump and fill the font of the structure with water. We watch the stream flow steadily down the steps of the waterfall and enjoy the originality of our suburban area.

DIY stone fountain

How to build stone fountain? We'll talk about this right now. First you need to make sure you have everyone necessary devices and materials. We will need:

• Water pump (underwater with medium power is suitable);
• Plastic container for the bowl;
• A metal or PVC tube for carrying an electrical cable;
• coupling;
• Flat stones and gravel;
• Wooden bars;
• Water flow power regulator;
• Copper tube with a diameter of 15 mm.

Pit for the fountain bowl there should be a slightly larger container prepared for these purposes. By filling the space between it and the walls of the pit with soil, we will significantly strengthen the position of the bowl. As in previous cases, do not forget to create a pit at the bottom sand cushion . On top you need to lay a layer of pebbles.

Water pump fits freely in the water tank. This will make it easier to repair it if the need arises. You can protect your water tank from debris by simply fine mesh. To give strength to the structure on top metal mesh are placed wooden blocks (if desired, they can be replaced with metal fittings).

The base of the fountain will be metal pipe, which is attached vertically to the pump.

The next stage is preparation flat stones. To do this, using special tools, we make holes with a diameter slightly larger than the diameter metal pipe- foundations of the structure.

Next, using the principle of a children’s pyramid, we “place” the stones on the pipe. All that remains is to add decorative elements to the fountain and connect the pump. A very simple, but effective and beautiful fountain at the dacha with your own hands is ready for use.

A variety of do-it-yourself fountains in personal plots

Submersible fountains

If there is already a pond in the yard, then it can be used as a basis submersible fountain. The principle of its operation is simple. Water is supplied via a pump directly from the pond. In this case, to install a submersible fountain you will need:

• Pump;
• Water supply pipe;
• An appropriate nozzle for forming a water jet and giving it the correct direction.

The attachments come in a variety of different types. Eg, bell attachment is a two-disk design. The flow of water passes between them and changes when the gap is adjusted. Nozzle " geyser"—a tube narrowed toward the top—quite effectively copies the corresponding natural phenomenon.

Such structures have quite a lot of possibilities. For example, you can create the effect of a key gushing out of the ground. To do this, install the fountain yourself so that the end of the pipe does not protrude above the surface of the reservoir.

Using more complex attachments, you can significantly expand your decor options. The effect of spraying water, the simultaneous combination of several nozzles and many other variations for the choice of those who construct a fountain in their dacha.

Stationary fountains

A fountain of this type is a real find for amateurs and professionals of design art. Structures can take the form of natural stone fonts, antique structures; they are made from clay pots, plastic bottles and any material that is at hand. Particularly popular in Lately fountains for Japanese gardens.

Any frost-resistant material will do: marble, fake diamond, sea pebbles and more. To decorate such fountains, they often resort to painting. There are two ways to do it:

• Coloring the material before manufacturing the structure;
• Painting the finished figure.

The first option costs much more, but it is also much more reliable. To protect against moss, fungus and mold, it is useful to treat the fountain structure with special products.

Small stationary fountain It will look good in family recreation areas or near children's playgrounds. Our master class “Do-it-yourself fountain in the country” will help novice designers correctly build, perhaps, one of the main decorative elements in the garden. suburban area. And it doesn’t matter whether it’s a small geyser fountain or a large cascading waterfall 2 meters high. The main thing is that it pleases the owners and does not cause problems.

Video instructions for making a fountain at the dacha

A cool, babbling fountain on a hot summer day is very invigorating and improves your mood. If you don’t have the time or opportunity to get out to a real fountain, then a small home fountain is just a salvation! Moreover, make a fountain for your home with your own hands very simple. My Master Class.

For a home fountain we will need:

• flower pot (without holes in the bottom) with a tray;
• small water pump (pump for pumping water, powered by mains, sold in construction stores or markets, cost 300-600 rubles, mine is 6x4.5 cm in size and 5 cm in height);
• acrylic paints,
• paints for glass and ceramics,
• contours,
• spray paint;
• pebbles for an aquarium;
• plastic plants for aquarium;
• decorative castle, again, for an aquarium.

1. Flower pot will serve as a cup for our fountain self made . To make it look beautiful, it needs to be embellished, that is, painted.

2. I chose “ mosaic" To do this, I applied random line cells on the outside of the flower pot using a golden outline.

3. Then I filled the cells with acrylic paints, as well as paints for glass and ceramics (I used everything that was at hand and that did not require firing to dry).

4. I painted the inside of the container and tray with blue spray paint. You need to be careful here. It is better to wrap the pot with some kind of rag so that small splashes of paint do not end up on outside pot and did not spoil the drawing.

As an option: you can paint the pot and plate first with spray paint, and then start painting the outside.

5. So, the main job is done! Here's how the pan will be installed.

6. Under the tray there will be a pump for the fountain. In order for water to circulate, small holes must be made in the bottom. holes for drain. In addition, the hose from the water pump will also need to be threaded through the hole in the pan. Since our base is plastic, it is easy to melt the holes with a hot nail (heated, for example, on a stove).

7. Now the details. I lightly painted our water castle with glass and ceramic paints, and covered the circumference of the fountain with colored aquarium pebbles. Of course, you can come up with a different decor for your handmade fountain!

8. When everything is ready, you can collect the fountain. I passed the water supply tube through the window of the ceramic lock and filled the bottom with pebbles for the aquarium.

I slightly enlivened the “landscape” with branches of artificial algae.

And now he is already quietly murmuring, small, but so cute handmade indoor fountain! :)

You can find the original of this master class on its author's website

Master class tabletop waterfall, DIY decorative fountain

Author: aquamagic

Reducing indoor air humidity is a side effect of heating an apartment in winter period. Moreover, excessively dry air not only causes discomfort when breathing, but also causes an increase in the number of colds. The dry mucous membrane of the nasopharynx becomes more susceptible to all kinds of infections and viruses. That is why during heating season You should consider humidifying the air.
On sale you can find many different devices for air humidification: evaporator, steam generator, humidifier, etc. Some owners simply place an open bowl of water in the room. As you can see, there are many options, but none of them are suitable for creative people, since our imagination simply cannot accept this simple solution. After all, there is an opportunity to do something very useful and most importantly beautiful thing, with your own hands. So, after thinking a little, we found a way out by offering you, dear readers, make an indoor fountain. You can install this beauty in any convenient location: on the floor, on the table, on a stand. A decorative fountain will be an excellent interior decoration and will fit perfectly into any style decision. Moreover, the murmuring water of an indoor waterfall creates a peaceful environment conducive to rest and relaxation.
Master class tabletop waterfall. DIY tabletop fountain.
To make a tabletop waterfall-fountain craft, we first of all need a mini pump for (water circulation in the fountain) lifting water from the lower reservoir to the upper reservoir. It is best to use a pump water pump, which you can simply put in the lower reservoir (pond) and pump water up. Unfortunately, we do not have such pumps for sale, therefore, in this master class, we use a water pump from household appliances, or rather from an electric samovar (photo below).

The lower reservoir reservoir is made from plastic bottle from under oil (5 l). Cut off the lower part with a height of 5-8 cm.

A round cake tray with a diameter of 29-30 cm is used as a base. You can use any shallow plastic container.
Connection of the pump to the lower reservoir. Using a hot soldering iron, make a hole in the bottom reservoir. The hole should be 0.5mm smaller than the diameter of the pump tube. This is necessary to ensure that the connection to the pump is tight, which will avoid leakage. If you cannot tightly connect the pump to the reservoir, you can proceed as follows: put a piece of soft hose on the pump tube and thread it into the prepared hole, which will seal the connection (see photo below).

At this step you can check the operation of our fountain. Also check if there is a leak somewhere.
The above steps are only necessary if you do not have a pump pump.
Relief production. To make the relief we will use construction foam. Cover the entire base with foam to a height of 5-6cm. Wait for the first layer to harden. This will take approximately 3-4 hours and start building up the slide (base of the waterfall) (see photo below). We gradually increase the base of the waterfall by 15-17cm.

After the foam has completely hardened (after 10-12 hours), we begin creating a waterfall. We cover the bed of the waterfall with pebbles and place a small lake on top. After completing the formation of the waterfall, coat the bed well and, especially carefully, the seams between the stones waterproof glue liquid nails (see photo above).

After the glue has dried, we check the operation of our tabletop fountain - waterfall. It will not be possible to get a beautiful drop of water right away, therefore, using a gun (hot glue), we form 3-4 nests in which streams of water will form and fall down, see photo above.
Next, we proceed to decorating the waterfall and painting our tabletop fountain. Why will we prepare a special paint?

Pour PVA construction adhesive diluted 1:1 with water into a container, add color and sand. Stir and add sand until it reaches a creamy consistency. Let's prepare several shades of green and paint our craft, applying each layer after the previous one has dried.

The result of painting a decorative fountain is shown in the photo above.
Let's start making the base (pallet) for our tabletop waterfall - fountain craft.

From thick sheet cardboard we cut out a circle with a diameter of 30 cm, and another circle with internal diameter 30cm and outer diameter 32cm, strips 5 and 1.5 centimeters wide. Glue all the parts as shown in the photos above.

We install our waterfall on the base and proceed to the final stage.
Between working on a tabletop waterfall, I assembled a tree from sequins on a stone, photo below

We glue the tree into a previously prepared place and complete the work on the tabletop fountain - waterfall, covering all the flaws and minor shortcomings.

So I'm ready original craft. Looking at her, you would never think that you can create such beauty with your own hands and use available materials for this. This indoor fountain will make everyone happy. What's not an idea for a great gift?!

It would seem that when we offered you to make a fountain for your home, we were thinking about humidifying the air in the room, but in the end we not only solved this problem, but also brought a touch of originality and sophistication to your home.

Material taken from ourworldgame.ru