In order to install a door yourself, you need to have some experience and knowledge in this matter. MDF slopes front door in this case they are part of space, and quite important. Installation of slopes, which are often made of MDF, takes place on final stage installation of the door itself.

The function of MDF slopes in this case is, firstly, to improve the appearance of the structure, and secondly, to insulate the room. The installation method may be different, but it is necessary to take into account the material from which the door leaf itself is made, since this is what determines protective properties doors and others no less important characteristics. When installing a door, you need to consider the following rules:

• to ensure free opening of the door, installation of slopes must be done at the bottom of the frame (20 mm);
• slopes on the front door should be placed at different distances;
• For correct installation The door needs to be measured correctly.

Facing can be carried out in various ways. The standard method includes attaching a ready-made slope directly to the box itself. In this case, there is a great saving of time, since it is not necessary to make the slopes for the entrance doors themselves.

There is a finishing option using plasterboard or plaster. This method is considered no less popular, however, not everyone can carry out such finishing, since this requires some knowledge in the construction field.

In order to decide on the method, you need to know the type installed box. If door slopes are installed on interior design, insulation in this case is not required. Here the best option there will be cladding with decorative materials.

As for entrance doors, they require more careful and attentive work. Here, the best option would be MDF panels (fibreboard). Their popularity is quite high, since this material is not affected by temperature and dampness. The color of the panels in this case is selected in accordance with the color of the door itself. High-quality finishing includes the combined use of MDF with plaster.

Tools and materials for work

Before you start work, you need to make sure you have all the tools. To install entrance door slopes using a combined method, you will need:

• foam used to seal joints;
• primer, cement, putty, sand;
• dowels;
• mortar;
• profile used in construction;
• liquid Nails.

Manufacturing instructions

This method requires special attention, so you must follow all instructions exactly. It would be useful to watch a video on the topic: “How to make slopes.” Once the door has been installed, cracks may appear along the edges. In this case, in order to seal such gaps between the wall and the frame, special foam (mounting foam) is used. After using it, you need to wait for some time for it to harden, cut off the excess and level the surface.

Next comes surface treatment in those places where the joints will be located. The first step is to apply a primer, which will strengthen the material and improve its protective properties. The evenness of the surface can be ensured by plastering using a profile. As for the corners, they are attached to the corner using dowels.

You can start plastering, but first you need to prepare the appropriate solution. It is easy to prepare, just mix sand, cement and lime solution. In some cases, it can be replaced with putty, which is used for cladding facades. It must be applied in an even, fairly thick layer, removing excess with a wooden lath.

The corners are strengthened using a perforated profile laid in a layer of plaster. The next layer should be applied after the previous one has dried. Once the puttying process has been completed, the MDF panels can be installed. Finishing the entrance door slopes MDF panels do it yourself includes the following steps:

1. Before starting work, it is necessary to prepare the base for the slopes for the front door. The corresponding solution is placed on the surface, after which it needs to dry. A primer layer is applied.
2. MDF cutting. It is done to get three individual parts on top part structures and side.
3. Glue is applied to the upper part of the opening and the MDF panel is pressed. It must be pressed and held until the mass dries. Other parts of the slope are made in the same way. For a tighter fixation, as recommended by the builders, you can use spacers.
4. The space created during the work process is covered with small plastic.
5. The next step is measuring the angles of the opening. To prevent cracks from appearing, before installation, you need to apply the material and see how tightly it fits. Then we attach the panel parts to the corners. It must be taken into account that the corners account for half the opening angle.
6. The final stage is decoration. For this, the same material from which the door itself is made is used.

Thus, observing all the nuances and following the instructions, it will not be difficult to carry out the work efficiently, and if you still have any questions, you can watch the corresponding video.

When you decide to make repairs in own apartment or home, sooner or later it comes to replacing the doors. In order to do this correctly, the master must have some experience in performing such work, since it requires care and precision at all stages of dismantling and installation.

It is natural that Special attention should be given to finishing door slopes and openings. The quality of finishing of the doorway with MDF panels will depend on visual perception doors and repairs in general.

Types of slopes and rules for installing doors

Slopes can be divided into external and internal, according to their location relative to the room. The final stage in the door installation work is finishing the door slopes. The main thing is to solve two main problems in this process: thermal insulation and aesthetic. It is also important to choose the right construction material, which will be used for installing doors and mounting slopes.

The issue of choosing a work technology remains important. Upon acceptance the right decision, the doors will last for many years and will perform all the necessary functions. Without experience, it is difficult to make slopes with your own hands, but if you strictly follow all the recommendations, the result will not disappoint you, you can see an example in the photo.

Installation of slopes

Rules that will allow you to produce quality products installation work on the formation of slopes on the doorway:

1. The slopes should preferably be placed 1.5-2 cm lower than the level of the box;
2. the distance from one external slope to another must exceed the distance between two internal slopes;
3. In order to install doors correctly and make smooth slopes, you need to accurately measure the dimensions of the doorway.

Various finishes

Today you can use one of the types of finishing of openings or slopes MDF doors DIY panels. The easiest way is to glue a pre-made slope to the door frame. You can see what it looks like in the photo. To create it, MDF panels are used. Naturally, this will significantly reduce the time spent on finishing work and will also facilitate the efforts made. You can even do this work yourself.

The advantage of MDF panels, which are made from pressed wood waste, is that they are not afraid of temperature changes and humidity fluctuations.

If you are looking at additional decorative MDF elements, the shade of the color of the door leaf must be taken into account.

Central heating in the house involves predominantly “dry” finishing technology. For optimal thermal insulation and increased sound insulation capabilities, the box must be caulked. The joints that remain between the wall and the frame are traditionally sealed with a special solution. The panels used to cover the slopes are fixed using mastic. It is recommended to paint the slopes afterwards outer side, preference should be given to oil paint.

In houses where it is installed stove heating, predominantly use wet plaster (photo). The solution that is prepared for finishing work will include different components depending on the building material from which the walls are made, the level of moisture content in the air, etc. The main requirement will be that the plaster adheres tightly and reliably to the wall surface.

Metal doors require their own specific actions when installing slopes and finishing works. For slopes in this case it is better to use a cement-sand composition. If the slopes are wooden, then they are filled with polyurethane foam. The negative aspect of this option is its reduced insulating properties.

Advantages of different finishing methods

The main criterion when choosing the finish of a doorway, slopes, etc. is the location of the door itself. If installation work is carried out on doors interior design, then strengthen thermal insulation properties there is no need, the main thing is the aesthetic characteristics of the door and finishing work.

Finishing entrance door slopes with MDF panels, on the contrary, requires increased strength, increased protection from temperature effects and increased soundproofing properties. You can see samples of them in these photos. More often, several materials are used for these purposes.

Some of the most popular ones are plaster and MDF panels. This is the best option, which will provide protection from cold and extraneous sounds, while guaranteeing reliability and safety of external data for a long time, even during active use

Do-it-yourself combined MDF panels

1. The first step is to get rid of the gaps that have formed between the wall and the door structure. For these purposes, polyurethane foam is preferably chosen. When the cracks are filled with foam, you need to wait a little until it hardens, then use assembly knife Excess is cut off and unevenness is leveled out as much as possible.
2. After this, the installation surface is treated with a primer, this further increases the “adhesion” between the plaster mortar and the wall.
3. It is better to apply plaster along beacons, which are used as metal profiles, attached to the wall with dowels. Then the application will be as even and smooth as possible. Plaster is prepared from the following components: cement, sand, lime mortar.
4. If you need to save time and are not afraid of additional expenses, then purchase ready putty, which is adapted for facade works. External corners reinforced with a mounting profile, which is carefully pressed into the uncured solution. Final stage– finishing coating.
5. Now you can start finishing using MDF panels. The cement-lime composition serves as the basis for the slopes. When it dries, the surface is thoroughly treated with a primer solution.
6. Next, 2 side parts and 1 top part are cut out of the MDF panel. The glue is applied to the upper part of the surface of the slope and the MDF part can be pressed against it. It must be held tightly until it is completely stuck with glue.
7. In the same way, glue 2 side panels. To further ensure secure fixation, you can use spacers. It is recommended to seal the gaps that have formed between the wall and the MDF panels using decorative corner made of plastic, glue with “liquid nails”. When you cut MDF panels, you need to carefully measure all the corners to avoid mismatches during installation work.
8. The doors are finished with MDF panels.

You can also view photo and video materials about the technology of finishing doors with MDF panels.

Window and door slopes made of MDF are much more difficult to make than structures made of other materials. While any craftsman with minimal skill can handle plaster, drywall or plastic, working with wood-based boards requires almost a jeweler's precision of fit.

However, the result is worth the effort, so below I will provide all the information that needs to be studied before proceeding with installation.

Advantages of slopes made of MDF

As a rule, slopes (internal side surfaces window or doorway, not covered by a frame or door frame) after installation of the structure itself does not look attractive enough. In most cases they require, and different materials are used for this purpose.

The most commonly used slope finishing technologies include:

• plastering followed by putty;
• plasterboard covering with further finishing with decorative materials;
• finishing with plastic panels;
• clapboard cladding.

One of the design options is also covering the opening with MDF panels.

This solution has several obvious advantages:

1. The material compares favorably in strength to gypsum board and plastic lining. The structure turns out to be quite strong, and therefore, for example, finishing the slopes of the front door with MDF panels is the preferred solution: even under conditions of increased operational load, the panels will not be damaged.
2. The design technology does not contain “wet stages”. We don't have to wait for it to polymerize and dry completely. plaster mortar, which significantly reduces the time spent on finishing.
3. After covering, no additional finishing of the slopes with decorative materials is required: no putty or painting is needed, which reduces costs and work time.
4. The appearance of the structure is also very attractive. If you match the slopes on the MDF door to match the door leaf and door frame (or with window frame and sash), then the whole set will look just perfect.

If we talk about the disadvantages, then the main disadvantages will be the complexity of manufacturing that I have already mentioned, as well as the fairly high price. Yes, on related materials, such as paint or plaster, we will save, but the laminated MDF panels themselves cost a lot.

Manufacturing technology

Tools and materials

To install panels with our own hands, we need to use a whole arsenal of tools.

I usually prepare the following set for work:

• hammer drill with concrete drill;

Advice!
To install in an opening made of wood (timber or log), you can abandon the hammer drill in favor of a conventional, but quite powerful drill.

• screwdriver;
• jigsaw;
• awl for MDF (hacksaw, disc or reciprocating);
• a breadboard knife with a long, strong blade;
• hammer;
• foam glue gun;
• level;
• roulette;
• pencil or marker.

I make the slopes themselves from MDF panels 10 mm thick.

Except decorative material at work I use:

• wooden slats for the frame;
• antiseptic primer;
• repair composition for concrete or brick;
• decorative corner overlays;
• platbands;
• "liquid Nails";
• self-expanding polyurethane foam.

Preparing the opening for installation

MDF slopes can be mounted both on the opening itself and on a frame made of wooden beams. The first technique is used relatively rarely: for it successful implementation It is necessary that the edges of the doorway be sufficiently smooth.

That is why I almost always mount panels of decorative material on a frame made of beams rigidly fixed to a solid foundation.

The work is carried out according to the following scheme:

1. Using a hammer drill with a chisel attachment, I knock pieces off the slopes old plaster, which remain on the surface after replacing doors.
2. I clean the walls of the opening from dust and debris, and then check for the presence of gaps and cracks in the load-bearing surface.

1. If defects are found that reduce the strength of the base, I repair them using a cement-based or epoxy-based composition.

Important!
Cement dries more slowly, but is cheaper than more effective epoxy compounds.

1. To avoid the appearance of fungus or colonies of pathogenic bacteria, I treat all surfaces that will be hidden under the cladding with an antiseptic primer.
2. Next I mount it on internal surfaces opening frame made of wooden beams, also impregnated with antiseptic. I level the beams and fix them to the wall with express-installation dowels with plastic sleeves. To prevent the parts from moving, I hammer wooden wedges into the gaps between the frame and the opening.

1. Slopes for entrance doors and windows can be additionally insulated. To do this, I either put thermal insulation material in the cells of the frame (foam plastic is enough, but if finances allow, feel free to take mineral wool), or I blow out the space between the beams with self-expanding foam.

Advice!
When foaming, I moisturize both the surfaces themselves and the foam.
The instructions allow the installation of panels only after polymerization of the composition and cutting off excess, since otherwise there is a risk of deformation of the panels.

Installation of slopes

Now all we have to do is make the slope strips themselves and install them on the prepared frame.

I act like this:

1. I cut out three blanks from an MDF sheet: two for the vertical parts and one for the horizontal.
2. I apply the blanks to the opening and mark on them the lines along which the trimming will be carried out.

1. I trim the parts strictly to the size of the door or window opening.

Important!
There are two options here: simple and complex.
When it’s simple, we cut the panel at 90 0, and cover the gap between the parts with plastic or laminated cardboard corners.
It will be a little more difficult to trim the end of the panel at an angle of about 45 0, which will allow the parts to be joined with a minimum gap.
You can use a miter box for trimming, but it is only suitable for narrow slope strips.

1. I apply “liquid nails” to the underside of each panel, and then glue the MDF to the frame.
2. I carefully align the panels, ensuring that the gaps between them are minimal.

1. Additionally, I strengthen the fastening with self-tapping screws, tightening them at the top and bottom. I hide the screw heads in pre-drilled secret holes, covering them with decorative caps to match the panel.
2. I fill the gaps between the parts either with tinted putty or (if they are not wider than 1 mm) with transparent sealant. In the second case, I make sure that the sealant does not remain on the front surface of the slopes.
3. I complete the finishing of the opening by attaching platbands to the ends of the slope strips and to the walls located next to them.

Conclusion

Finishing door slopes with MDF panels is a rather labor-intensive process. However, despite the complexity of the technology, it is quite possible to master it - the above recommendations, the video in this article, and expert advice (including mine) will help you with this, which you can get by asking a question in the comments below.

MDF is one of the most popular materials used for finishing. Such panels look very representative and also suit any style. Very often used for finishing doorways. Let's take a closer look at how to make slopes for the front door with your own hands from MDF.

MDF slopes are a popular option for finishing a doorway

Features of the material

To complete prerequisite is to create smooth and neat slopes. Often, owners decide to do everything themselves. A wide variety of materials are used for these purposes; MDF is one of the popular options.

MDF slopes can be used for entrance doors in almost any interior. This material has a number of positive qualities:

• Strength. Resists moderate impacts and most damage.
• Decorative. It looks great and adds an atmosphere of comfort and style.
• Variety of coatings. May differ in color and type of top layer: veneer, eco-veneer, PVC, etc.
• Ease of installation. Easy to process and install with your own hands, even for a beginner.
• Imitation wood. The coating basically imitates wood texture and may look like an expensive species.
• Soundproofing. Provides additional protection from noise from outside.

The main advantages of MDF panels are their strength and ease of installation.

It should be taken into account that under unfavorable operating conditions, in particular high humidity, and also when using low-quality material, MDF can peel off over time, swell and delaminate. Also, the coating does not withstand strong impacts and contact with sharp objects.

Insulation of the opening and preparation

The first thing to start with is preparing the opening itself. It's very easy to do it yourself. First you need to free the opening from everything superfluous, in particular, from remnants construction waste. If you are afraid of getting dirty or damaging new door you can leave it there protective film or remove the canvas altogether while the work is being carried out.

First of all, remove dust and seal all cracks with foam or sealant. Then you need to take care of applying antiseptic impregnation or primers. To further insulate the opening from the cold and noise from outside the apartment, a layer of insulation should be laid along the slopes. The following are most often used as such a substrate:

• mineral wool;
• isolon;
• padding polyester;
• polyurethane foam;
• foamed polystyrene.

Proper finishing of the entrance door slopes requires a layer of insulation

An excellent option is spraying insulation, but this is a very expensive undertaking. To facilitate further cladding and final insulation of gaps, it is recommended to perform. A small layer will be enough, it doesn’t have to be perfect flat surface. Special corner profiles are installed in the corners; this will not only facilitate the leveling task, but will also strengthen such a vulnerable part of the slopes.

Marking and cutting

No less important stage in the process of finishing door slopes, rather than preparation and the actual installation itself - this means cutting the necessary fragments. In order to take measurements as accurately as possible, one tape measure will not be enough. Use a square and templates to create unique patterns.

You need to start with the bar that you plan to secure first. This is usually the top panel. Please note that in most cases the edges of the slopes are not evenly cut, but run slightly at an angle. All this should be displayed on MDF. Subsequent elements must be applied after installing the initial panel. That is why the process of marking and cutting is combined with installation.

Cutting MDF panels should start from the top strip

You can cut MDF using a hacksaw or saw, but the best option is a jigsaw. Thanks to its cutting element, it is possible to obtain a perfect cut without chips or burrs. Plus, you won't have to put in any effort.

When working with sidewalls, be sure to take into account the presence of a threshold. This important point, as it can significantly affect the height of the side bars.

Installation of panels

In order to install door slopes into the opening with your own hands, you need to complete several stages of work:

1. First you need to decide on the mounting method. If the panels do not have lock connection, the easiest way would be to secure them to the frame. As a last resort you can use aluminum profiles or wooden planks, which is more preferable.
2. Determine the level at which the trim will be placed. In this case, it is important to take into account the thickness of the panels themselves, since if the material protrudes excessively in the opening, movement may be difficult door leaf.
3. The frame is fixed to the wall using bolts. You will also need a drill for this. WITH inside you can fix the bar on itself door frame. There is also an alternative wooden frame– special guides that are installed at the corners of the opening. This option is suitable for installing L-shaped panels.
4. After the frame is fixed, MDF panels are applied to it and all excess is cut off. Can be fixed first top bar, and then proceed to the sides or do the opposite. MDF can be glued to wooden planks using liquid nails or nail it. In the latter case, small nails without heads are used.

Examples of finishing entrance door slopes with MDF panels

In order to eliminate drafts, additionally insulate slopes and provide stronger adhesion, polyurethane foam is used. It is important not to smear the MDF during the foaming process, as it will not be easy to clean.

Final finishing

After the mounting foam has dried and the glue has set, you can begin the final finishing. First of all, it is necessary to cut off all protruding areas of foam along the edges. This is best done with a painting knife. To prevent the foam from collapsing under the influence external environment it needs to be carefully puttied. To avoid smearing the new slopes, cover them with masking tape.

The final stage of installation of slopes is the installation of platbands

To give the doorway an ideal appearance, platbands are installed on top of the sealed cracks on the slopes. The last stage is masking the connection points. If you used nails, then you need to use a special mastic to match the finish or furniture stickers.

Thus, it is possible without special effort install slopes for entrance doors both from MDF and other similar materials. It is quite possible for anyone to do everything with their own hands, since they are used for work available materials and simple technologies.

To make the updated interior look complete and pleasing to the eye, you need to take care of “ small details" So, for the installed new interior door, it is necessary to select door slopes made of MDF. They will emphasize the beauty of the door leaf, help create a harmonious and holistic perception of the entire interior, and add a touch of completeness to the decor and design.

Of course, the modern market offers a lot of options, but it is the slopes for MDF doors that are most popular. What is the secret of their popularity, what variations are possible and how is installation done? Let's consider all these questions in more detail (see).

MDF door slopes: advantages and disadvantages of choice

From a technical point of view, the process of finishing slopes is a simple task, which is quite possible to cope with yourself. You just need to choose the appropriate color and texture of the MDF panels for the door slopes and begin installation.

Why the option made of MDF, and not PVC, wood, or other materials? Everything is very simple, since MDF panels have a number of undeniable advantages. Among them, it is primarily worth noting:

1. Beautiful appearance. MDF door slopes fit perfectly with any interior style chosen for the decoration of the premises. The material also harmonizes with furniture, flooring and other elements.
2. Ease of installation. If you take your time and first understand the principles of assembly and installation, then it’s quite possible to handle the work yourself.
3. Affordability. Finishing doorways MDF panels will cost an order of magnitude cheaper than veneer or natural wood. At the same time, MDF slopes are in no way inferior in appearance, aesthetic properties, and performance characteristics.
4. Additional heat and sound insulation of the premises is provided. This is an important factor for most users, which is taken into account at the stage of selecting materials for finishing.
5. Environmental safety of the material. It is non-toxic, does not contain harmful components, and has no negative impact on human health, does not cause allergic or other irritant reactions from even a sensitive organism.

Manifold color solutions, which offer MDF panels for door slopes, allows you to choose without any problems suitable option for any door, any interior design style.

MDF slopes for entrance doors - a practical and attractive solution

Almost every family has to deal with the issues of installing a front door, regardless of we're talking about about replacing an old door leaf with a new one or installing a door in a newly built house. We can say with confidence that one of the final stages in the entire installation procedure is finishing the door slopes.

The finishing of door slopes with MDF panels has proven itself to be excellent, allowing you to give the doorway a presentable appearance and neatness. At the same time, skillfully hiding the fastening elements protruding from behind the walls polyurethane foam and other consequences of installing the door structure itself.

Finishing door slopes from MDF panels allows you to:

1. Hide imperfections and unsightly consequences of installation.
2. Put the doorway and the entire “entrance group” in order as soon as possible. Compared to other finishing methods, MDF entrance door slopes require a minimum of time and effort for installation. The work is not as dirty and dirty as, for example, plaster.
3. Provide additional protection from noise penetrating into the premises, extraneous sounds, as well as protection from heat loss and cold penetration.

In terms of their aesthetic properties, slopes for entrance doors made of MDF are very often compared with analogues made of natural wood, since MDF panels differ:

• security;
• homogeneity of structure and high strength;
• resistance to the development of harmful microorganisms (MDF panels do not become moldy or rot);
• excellent performance properties (door finishing MDF slopes panels are considered a durable option, since the material does not warp, crack, swell, or deform, losing its original geometric shape and presentable appearance);
• diversity available options finishing (MDF panels for entrance door slopes can be with any type of applied relief pattern, milling, in almost any color scheme, including imitation of natural wood of various species).

What is also important is that MDF entrance door slopes are suitable as a finishing option for walls of any thickness and openings of any size.

Finishing technology and some secrets of the process

Finishing door slopes with MDF panels is not too difficult a task. If you wish, it is quite possible to design a door frame from MDF with your own hands. In this case, no effort is made, there are no significant costs for the purchase of special equipment or equipment.

The entire process of installing slopes can be divided into stages:

1. Preparing surfaces for installation. Removing contaminants from the surface of walls. Elimination of existing chips and cracks in the wall. If necessary, laying thermal insulation material. In preparation for installation finishing panels made of MDF, it is important to fix it correctly door jamb so as not to damage the wires passing here in any way.
2. Detailing. Allows you to accurately cut out all the necessary elements in the future and position them correctly on the canvas. This is what they achieve minimum flow finishing material. At this stage, it is necessary to pay attention and take into account when “taking measurements” and drawing up a diagram of the component elements, such as the presence of a threshold, differences in angles of inclination at the corners, and the overall width of the doorway.
3. The installation process itself, which can be carried out with the installation of a frame or using the adhesive method.

Since MDF is a sheet material, it will not be difficult to draw the outlines and dimensions of the parts. We take into account the width of the wall and other features of the doorway. We cannot exclude the case when during installation it is necessary to join two panels on the wall surface. In this case, installation using a frame (sheathing) is acceptable. If there are enough solid elements for finishing, then it is quite possible to install it using the adhesive method.

Frame installation

Installation of the frame involves assembly and installation wooden sheathing, which will serve as a support for the parts. Installation technology using a frame provides:

• installing slats on the wall horizontally at a distance of 30-45 cm from each other;
• fastening the slats to the wall using dowels;
• It is advisable to fill the voids between the slats thermal insulation material or polyurethane foam;
• installation of MDF parts pre-prepared in size and shape;
• they are fixed in place using self-tapping screws (the caps of the screws are recessed and covered with special covers).

In the photo, the wide slopes of interior doors or the entrance group, the panel joints are made carefully. A feeling of integrity of the entire panel is created. This is one of the signs of high-quality, professional work on finishing door slopes with MDF panels.

Talking about glue method installation, it is worth considering that it is chosen in cases where:

• the surface of the walls is well leveled and does not have significant unevenness or other defects;
• The thickness of the laying seam is minimal.

When installing MDF panels using the adhesive method, it is not always possible to use insulation. Therefore, it is fundamentally important to thoroughly seal all seams, crevices, and cracks. Also, do not forget about treating the surface of the walls with a primer.

Choosing what to glue MDF trim or other elements when facing slopes, it is better to use special adhesive compositions. This will help:

• ensure reliable grip and strong adhesion;
• prevent assembly elements from falling off in the event of mechanical impact or temperature changes.

Let's sum it up

High-quality finishing of interior doors with MDF panels, as well as the slopes of entrance doors, implies:

1. Selection of panels taking into account the style, as well as color design doorways. The interiors of rooms “in contact” with door blocks are also taken into account.
2. Ideal appearance of doors and openings in general after completion of work.
3. Absence of any types of damage on the surface of the finishing layer.
4. Ideally even joints between elements and parts.
5. The absence of protruding “caps” of self-tapping screws, which can not only spoil the aesthetic perception, but also cause injury. They definitely need to be “recessed”, covered with special overlays, or at least covered over.

Combining a large set of advantages, a variety of colors and style solutions, as well as an affordable price, MDF panels are rightfully considered the most acceptable and practical options. Especially when it comes to the need for quick and high-quality finishing door slopes. They look equally impressive on entrance group, and on interior doors. Their installation adds a touch of completeness to the design and makes the interiors more beautiful.

Front door slope made of MDF panels - video