Drywall appeared on the building materials market relatively recently. Just 15 years ago, partitions and walls of buildings were built from foam blocks or bricks. Today, drywall is gaining more and more popularity.

The main advantages of plasterboard, compared to other finishing materials, include:

• ease of installation, since any owner can handle the installation of drywall;
• the ability to make a variety of shapes;
• preservation optimal humidity in room. Due to its porous structure, the material allows steam and moisture to pass through, the costs of which it retains;
• Thanks to some types of impregnation, drywall can be used in rooms and structures with high level humidity;
• the material is very light weight, so it does not overload the structure on which it is attached;
• drywall is much cheaper than similar materials;
• The material is environmentally friendly and does not harm health.

Drywall doorways are installed using a profile with a width of 50 to 100 mm. At the same time, it is cut with your own hands to the required size.

Necessary tool

To make a doorway out of plasterboard with your own hands, you need to have the following tool:

• building level;
• screwdriver or drill with attachments;
• roulette;
• perforator;
• polyurethane foam;
• plumb line to install guide profiles;
• pencil;
• cutter.

Even with a minimal set of tools, you can quickly and efficiently make a doorway with your own hands.

Doorway installation

Before you begin installing the doorway, you need to prepare a frame for it.

Installation of the frame for the opening is carried out as follows:

• the doorway post is installed to the ceiling and floor profiles;
• intermediate racks are installed at a distance of about 50 cm from each other to each wall;
• a U-shaped section is formed from plasterboard, after which it is attached to the horizontal crossbar above the door;
• the structure is fastened with self-tapping screws;
• if the structure needs to be given additional rigidity, a wooden beam can be inserted into the doorway.

After the frame is ready, begin laying solid sheets of drywall. This is very easy to do if you follow these rules:

• the gap from the installation site of the screw to the edge of the sheet should be about 1 cm;
• the optimal distance from one fastener to another is 15 cm;
• sheets placed adjacent to each other must be located on the same profile;
• the fastener head is recessed into the sheet by no more than 0.8 mm;
• the length of the screws used should be within 2 cm;
• Next, you need to seal all the joints and carry out other cosmetic work.

Thus, by attaching sheets of drywall to the prepared frame, you will get an aesthetic and beautiful doorway.

How to reduce a doorway with drywall

When remodeling a home, owners sometimes encounter a situation where the size of the doorway requires reduction. It is very easy to do this with your own hands, but before you sew up the doorway with plasterboard, you need to apply a layer of plaster on the wall near the door corresponding to the thickness of the plasterboard sheet.

Using drywall, the doorway can be reduced in the following way:

• plaster is removed 10 cm from the edge of the doorway;
• markings are applied to the walls and floor;
• according to pre-prepared markings, the starting profile is attached to the floor and ceiling;
• Point profiles are placed on the finished starting profile, which are then connected with self-tapping screws;
• after complete installation the frame must be reduced in original dimensions and fragments cut out from plasterboard for the future structure;
• special glue is applied to areas of the wall that have previously been cleared of plaster (it is better to do this with gloves). Plasterboard sheets are attached to the applied glue and after its polymerization, the edges of the sheets are fixed with self-tapping screws;
• The doorway slopes must also be reduced in size, after which they are covered with a strip of drywall, and all joints must be sealed with your own hands.

Doorway, especially if it concerns front door, can not only be reduced, but also insulated or isolated from extraneous sounds. This is done before covering with plasterboard, after the frame is installed.

It is better to choose polystyrene foam or mineral wool boards as insulation.

Installation of a door in a plasterboard opening

To install a door in a plasterboard partition, it is necessary to install the door frame, and then hang the panel.

To ensure that the box, built with your own hands, holds tightly, it is secured with special wooden wedges. After final fastening, the wedges can be easily removed.

All parts of the box are checked for correct installation building level. If all the parameters are in order, you can use self-tapping screws to secure the door frame into the opening.

The gap between the box and the stand must be sealed with a special polyurethane foam. In order for the shape of the opening to be completely preserved, it is necessary to insert spacers during installation.

A do-it-yourself plasterboard partition with a door built indoors is an excellent solution for zoning space. The design may contain built-in shelves or recesses. They house various items: books, decorative figurines, photographs. The configuration of the partition may be different. Curved lines are very popular non-standard forms. However, many novice craftsmen believe that building such a structure is quite difficult. Next, we'll figure out if this is true.

General information

Plasterboard partition with a door: organizing the doorway

The work begins with installing the racks. They will form They are attached to guides laid on the floor and ceiling. Next, intermediate racks are installed from each wall in increments of about 60 cm. Then a small section of the profile will be needed. Its length should correspond to the width of the future opening plus 2 racks of 10 cm each. The letter “P” is formed from this segment and attached to the place of fixation top crossbar the future box is upside down. To give greater strength, install 1-2 small racks, the size of which is equal to the distance from the crossbar to the upper (ceiling) guide profile. This creates a kind of frame over the future box.

Plasterboard partition with door: installation features

The frame for the future box must be assembled in such a way that the sheets can then be correctly placed and secured. If there are errors in the assembly, subsequently, when opening or closing the door, cracks may appear on the partition at the joints of the gypsum plasterboard directly near the opening. To avoid these problems, reinforcements should be placed on both sides of the box. To do this, a beam (40x40 or 50x40) is inserted inside the racks. Such reinforcement will not only add strength to the structure, but will also facilitate its installation. If there is no timber or there is no desire to use it as additional elements rigidity, you can install another rack profile in close proximity or close to the outer rack. All parts are fastened with self-tapping screws. As an option, you can immediately install a reinforced profile with additional ones. The more there are, the higher the load that the wall with a plasterboard door in the apartment will withstand. This completes the assembly of the frame. If necessary, wiring should be installed before covering the gypsum plasterboard (if you are installing lighting for a plasterboard partition yourself). How to do original design designs? Can be used as a backlight Spotlights or LED strips.

GVL fastening

Sheathing of the frame begins with solid sheets from the wall. Fastening gypsum fiber boards is carried out in the same way as when finishing walls and ceilings. During the work you need to ensure that:

• The distance from the edge of the sheet to the place where the self-tapping screw is screwed in was in the region of 1.0-0.5 cm.
• A spacing of 10-15 cm was maintained between fasteners.
• The joining of adjacent sheets was carried out on one profile.
• The self-tapping screw head was recessed into the gypsum fiber sheet by 0.5-0.8 mm.

When constructing a wall with a single-layer plasterboard sheathing, the length of the fastening element should be no more than 2.5 cm. When finishing with two layers of gypsum plasterboard, the self-tapping screw should be no less than 4.0 cm.

Using jumpers

Often, a single sheet is not enough to cover any area. In this regard, it is necessary to increase the GVL. In this case, it is necessary to install additional jumpers at the transverse joints of the sheets. Sections of guides or CD-60 profile are used as additional racks. When installing the jumper, do not apply strong pressure to it. The sheet must be fixed in short increments, using at least 5-6 screws for each side.

Final stage

After the GVL is fixed on one side, proceed to covering the other part of the frame. You can first lay insulating material inside - insulation (mineral wool or polystyrene foam). Its width should be slightly larger than the interprofile space. Then the material will be installed end-to-end between the racks, which, in turn, will eliminate the formation of gaps. After this, the second side is covered with sheets of drywall. After completing the fastening, the joints are glued with reinforced mesh and puttied. The screw caps are also masked.

Finally

In general, even an inexperienced, novice master can cope with the installation. All the work can be done independently, without involving anyone for help. The most important thing is to maintain verticality and horizontality when installing frame elements. The position is controlled by the building level. The advantage of plasterboard is that when it is laid, it creates a perfect Smooth surface. As finishing coating can be used various materials. Wallpapering and painting are very popular. The surface is also often covered decorative plaster. Can be used more heavy materials- stone, wooden panels. But in this case, a reinforced profile is needed for the frame, and thick plasterboard is needed for the cladding. Otherwise, the structure may not withstand the load and collapse.

Change the layout, or split it into separate rooms existing premises is not difficult. To do this, you can call a team of repair specialists or do everything yourself, provided you have certain knowledge and skills. Most often, plasterboard doorways are used for interior partitions. The installation process of such a structure must be thought out to the smallest detail, since its quality and stability depend on this.

The quality and practicality of drywall in use have been proven for a long time. It is used not only as a material for finishing walls, but also as the basis of structures and partitions dividing a room into several rooms. Each such wall must have a hole for the door, which greatly complicates the installation process. It's important to remember that doorway must have a certain rigidity so that a door frame can be placed in it, facing materials, slopes. If the presence of a door is not initially planned, such a need may arise in the future. A well-installed doorway will allow you to install the door without much hassle at any time.

The process of installing a plasterboard wall:

• Frame marking;
• Frame installation;
• Wall cladding with plasterboard.

At the beginning of work, you need to draw a plan of the walls in order to avoid shortcomings and further rework. Future doorways and the width of partitions should be marked on the drawing. The first step in installing a wall is to transfer all the elements from the plan to the floor and ceiling of the room.

The presence and location of electrical wiring and electrical appliances should also be thought out in advance.

To install the frame, a guide metal profile is installed, which serves as the outline of the partition. Fastening is carried out with a hammer drill or dowel-nails. Next, vertical rack profiles are mounted, after which the frame is filled soundproofing material and stitched with sheets of plasterboard.

How to install sliding plasterboard doors in an interior partition

Sliding doors in plasterboard partition take up little space and are ideal option for small rooms.

To install such a door you will need to carry out the following work:

• Calculate the mounting height of the guide and the size of the opening;
• Mount the partition frame;
• Install the door guide;
• Install travel limiters;
• Cover the frame with plasterboard;
• Lay a clean floor;
• Hang the door leaf;
• Install platbands.

When installing metal frame jumpers are used that connect the walls of the structure to increase rigidity. Double vertical posts are also installed, because it is impossible to install lintels in the space where the door will be hidden.

Installing a plasterboard doorway with your own hands

Doorways are made using guide profiles according to pre-marked markings. Size door block significantly affects the final width and height of the opening. Before calculating the height of the opening, you should pay attention to the absence or presence of floor covering.

The process of installing a plasterboard partition with a doorway includes the following steps:

• Installation of guides and rack profiles;
• Marking and forming the design itself doorway;
• Consolidation plasterboard sheets on finished design doorway;
• Installation of a plasterboard box for an air duct.

Before starting finishing work, it is necessary to check the wiring. To improve sound insulation, it is necessary to foam the gaps between the profile and the boards.

The racks along the edges of the doorway are reinforced with wooden blocks that match the profile in size. The presence of a wooden block significantly improves the quality of installing a door into a partition from plasterboard with your own hands, and also improves the rigidity of the structure. Self-tapping screws are used to attach the bars to the profile.

How to make plasterboard doors with your own hands

The process of manufacturing and installing plasterboard doors is not complicated, but the final result largely depends on the design planning.

In the process of manufacturing plasterboard doors, the following work must be performed:

• Install the door frame;
• Cover the door frame;
• Seal cracks;
• Carry out soil and putty work;
• Carry out the final finishing of the wall.

For the frame, a cut profile is used, onto which jumpers are attached to increase the strength of the product. The frame is sheathed with plasterboard of any size and even leftovers, since the finished canvas can eventually be primed and puttyed. All cracks and chips that appear as a result of the cladding must be properly repaired. After this, the doors are painted or covered with photo wallpaper or tiles.

In some cases, the door structure is insulated with polystyrene foam, glass wool, polyurethane foam, isolon, or polystyrene, and the material is placed in an empty space and fixed with glue.

In what order is a plasterboard wall and door installed?

To isolate a passage room, you can use interior partitions, for which material with different characteristics: moisture resistance and fire resistance.

Since the material is very fragile, you should work with it carefully and carefully to avoid damage.

Stages of installing an interior partition:

• Preparatory- taking measurements, preparing materials and tools;
• Mounting- the process of installing a profile, forming an opening for a door and installing drywall;
• Finishing- wall surface treatment various impregnations, applying paint, tiles, wallpaper.

Immediately before installing the door, it is necessary to divide the material into separate elements according to preliminary marking of the boundaries. The cut line should be leveled with an edge plane. The frame is sheathed on both sides with plasterboard using self-tapping screws.

How to sheathe a doorway with plasterboard correctly

Before sheathing the wall, it is necessary to correctly cut the sheets of plasterboard construction knife. To obtain even borders, place the sheet on a horizontal hard surface and mark with a marker the line along which you want to separate part of the material. Upper layer The drywall needs to be slightly cut. After this, the sheet moves to the edge of the support and breaks. At the end, you need to turn it over and repeat the above steps again, as a result of which you will be able to separate the desired piece of drywall from the sheet.

The sheet and frame are connected using self-tapping screws. Initially, it is necessary to fix the edges of the sheet, and only then the middle. A distance between fasteners must be maintained in the range from 10 to 25 cm.

It is important to screw the screws completely into the drywall so that the caps do not stick out above the wall level.

The work is carried out in the following order:

• The first sheet is secured;
• The distance to the ceiling is measured and a piece of drywall of the appropriate size is cut out;
• In places where it is necessary to fasten the sheet to another piece of drywall or the ceiling, you need to form a chamfer;
• After the first row, whole sheets are installed under the ceiling, and the missing part is attached to the bottom.

How to install a plasterboard doorway

When remodeling an apartment, a very popular solution is to finish the doorway with plasterboard. However, it does not have to be made rectangular. Nowadays, unusual and curved doorways are in fashion, and with the help of drywall it has become possible to bring any design idea to life.

At the beginning of work, it is necessary to dismantle the old door: remove it from its hinges and remove the trim and jambs on the floor.

Installation of a plasterboard doorway is carried out in several stages:

• Installation of a rigid frame for fastening sheathing sheets;
• Installation of the upper transverse strip to fix the upper dimensions of the opening;
• Measuring the parameters of the frame according to the width and height of the doorway;
• Preparation of materials for installing doorways and sound insulation;
• Marking drywall;
• Fixing drywall sheets with self-tapping screws;
• Taping seams with sickle tape;
• Putty and primer of the doorway;
• Final decorative finishing.

We make a doorway from plasterboard with our own hands (video)

A plasterboard doorway can be the highlight of a properly chosen design. A partition with a compartment door is especially relevant in modern interior. The main advantage of this design is its ease of assembly. Thanks to this, there is no need to pay money for installing such a wall and preparing the material, because it is very easy to do it yourself.

Design of doorways from plasterboard (interior photo)

Many modern apartments do not have a layout and therefore the owners independently divide the total area into rooms using interior partitions, or use decorative partitions to zone the room.

The simplest, fastest and in an accessible way creating interior partitions are plasterboard structures . Such partitions can be either solid or with a door, and if you have the desire and time, then you can make them yourself.

Advantages of plasterboard partitions

Drywall is universal building material, which is used both for finishing a room and for creating new structures in it, including interior partitions, and for creating partitions for zoning in an office and apartment. The only things that can compete with it in terms of characteristics are: partitions made of tongue-and-groove slabs or polystyrene concrete blocks.

• This lightweight material , so the load on the structure of the house will be insignificant;
• All work with it is done by hand, without the involvement of assistants, since the material is light;
• the cost of drywall is low, as well as the materials necessary to create the frame and surface finishing ;
• material is easy to cut, it bends easily, so even arched structures are created with its help;
• installation of the frame and sheets is simple and quick;
• finishing of such structures is carried out with various materials;
• plasterboard sheets consist of natural materials, therefore they are safe for human health.

Eat different types drywall, so before buying it, you need to decide which one you need:

1. ordinary, more often gray, used in rooms where humidity is not more than 70%;
2. moisture resistant, has a green or blue color and is used in rooms where there is constantly high humidity;
3. refractory, usually used in the kitchen, where there is a possibility of strong heating of the wall, it contains fiberglass and other additives, it is red or gray in color;
4. fire-resistant moisture-resistant, it is rarely used in rooms with difficult conditions.

The thickness of a regular sheet is 12.5 mm, and to create arches they use sheets 6.5 mm thick, to give them flexibility, they are pre-moistened.

Never do doorways like this! Error when installing plasterboard partitions

A video showing a mistake made by finishers when erecting interior partitions. This applies to doors...

Installation of an interior partition

At the first stage of the work, it is necessary to determine the location of the future partition. To mark, use a plumb line and a cord, parallel lines are drawn on the floor and ceiling.

Much easier to work with laser level, but buy it only to create plasterboard wall inappropriate.

When marking, the width of the partition is also taken into account, if it is sheathed in one sheet, then 2.5 cm is added to the thickness of the frame, and if the gypsum board is laid in two layers, then 5 cm is added.

To perform the specified work, you will need the following tools:

• building level;
• measuring instruments;
• cord and plumb line, or as their replacement - a laser level;
• corner;
• electric drill;
• metal scissors or jigsaw;
• pencil;
• stationery knife;
• putty knife;
• container for plaster.

After marking, cut the profile to the required length, back walls cover with sealing tape.

Installation of profiles

Work begins with laying and securing the guide profile to the floor, after which it is installed along the entire perimeter of the future partition. The profile is fastened using self-tapping screws or dowel nails, it all depends on the material of the walls.

Now, using the rack profile forming a doorway, this must be done carefully and carefully, so that the distance between the posts at the top and bottom is the same. The verticality of the racks is checked by level, after which they are fixed.

On next stage the remaining rack profiles are mounted if you have gypsum plasterboard standard width, then the distance between them is required 60 cm.

To increase the strength of the future partition, between the vertical posts it is necessary to secure horizontal jumpers, which are cut from the same profile.

A wooden block is also installed and secured into the transverse profile located above the doorway; it should easily fit into it so as not to disturb the shape, using a square check that the angles are 90 degrees.

The remaining transverse profiles are attached to the racks; special short screws are used for this.

After the frame is created, you will see that its structure is quite rigid and durable, start laying electrical wiring. The rack profiles have holes through which it will be convenient to thread wires.

The wiring is placed in a special corrugated non-combustible insulation.

Fastening drywall

At home You can use a utility knife to cut drywall and a long ruler or staff. To do this, apply a ruler to the sheet, make a cut along the line several times, the deeper it is, the better, and then carefully break the gypsum board and get the required size.

To simplify finishing work, make a chamfer at the cut site at an angle of about 45 degrees, a plane or knife is used for this.

During the calculations, It is necessary to foresee in advance the places where you plan to mount hanging furniture or equipment.

Here additional profiles reinforced with wooden blocks must be installed, it all depends on the weight of the suspended structures.

Left place the sheet on the posts and secure it, this is done using self-tapping screws; they are installed in increments of 20 cm and slightly recessed into the sheet.

Carrying out finishing work

Installation of the frame and gypsum board is only the beginning of creating a plasterboard partition. At the next stage All seams are sealed. To do this, use sickle tape and putty. The entire surface of the wall is also puttyed.

After the base has dried, begin leveling the surface. The wall is covered with primer, which will allow the plaster to adhere better and provide additional protection GKL. Leveling is carried out with a wide spatula and finishing plaster.

Door block installation

In the prepared opening is performed installation of a door frame, do this with wedges, screws and polyurethane foam. First, the frame is aligned using wedges and fixed with self-tapping screws, after which they proceed to installing the door leaf.

The correctness of the work is checked, and the door should open and close easily. If everything is normal, then the remaining gaps are filled with polyurethane foam.

At this time, the door is in the closed position, or spacers are inserted into the frame so that when the foam hardens, it does not deform it.

The foam is cut off after it has completely hardened; if the canvas was removed, then it is hung only a day later, after installing the box.

Finishing

On last stage creating a wall from plasterboard, its finishing is carried out, for this purpose it is usually use paint or wallpaper. The frame is covered with platbands, which help hide the door attachment points.

Features of insulation and sound insulation

It is not recommended to leave a hollow partition; it will be filled with sheet or roll insulation. They are laid after one side of the wall is covered with plasterboard, and only then is it sheathed on the other side.

If you plan to install it in such a wall engineering communications or sliding door, then in the place where they are located, insulation is not laid.

To create sound insulation, use mineral wool or isover. From below, when installing the sheet, you need to leave a small gap, so stands of the appropriate thickness are installed.

In order for you to be able to create a plasterboard wall with an opening for doors yourself, must be adhered to the following tips specialists:

1. During the installation of partitions in the room must be at least 10 degrees Celsius.
2. You need to calculate required amount guides and rack metal profiles, only then purchase them. Cut them according required size You can use a jigsaw or metal scissors.
3. The sheets are laid tightly to each other.
4. To create holes for sockets, you must use special drill bits.
5. In the places where the sheets are joined, be sure to use a sickle and seal the heads of the screws well with putty, after which the entire wall is puttied.
6. As finishing materials, you can use paint, wallpaper, tiles, cladding panels and others.

Conclusion

Now you see that there is nothing complicated in the construction of plasterboard partitions and all the work can be done independently. Having studied the technology for performing the work, advice from experts and having prepared the necessary tools, feel free to begin performing the specified work.

Useful video

How to make a partition from plasterboard with your own hands, step-by-step instruction on video:

How to make a plasterboard partition with an interior door

Drywall is an excellent material for building a lightweight and inexpensive interior partition in the apartment. In addition, installation does not require much time.

A plasterboard partition can be made in the form of an arch or a door can be installed in it. You will learn how to install a door in a plasterboard partition from this article.

Construction of a doorway in a plasterboard partition

The process of assembling a plasterboard partition is described in detail in a separate article “Drywall partitions for zoning space in a room,” so we will not dwell on it, but will only briefly touch upon it.

pros

The positive aspects of a plasterboard partition:

1. Light weight allows you to build a partition without loading the floor slabs;
2. The process of assembling the structure is very simple and does not require much time for installation, in addition, it can be easily done independently;
3. Drywall and galvanized profiles are quite inexpensive, so such an apartment redevelopment will not hit your wallet hard;
4. A plasterboard partition is considered a temporary structure and does not require approval for the redevelopment of the apartment.

Installation of gypsum plasterboard partitions

First of all, markings are applied on the floor or ceiling, according to which the plasterboard partition will be installed and the place where the doorway will be made is indicated.

You need to select a door with a frame in advance and know them exact dimensions. The doorway in the plasterboard partition must be made taking into account that it can be entered door frame, which you chose, and there was a margin of about 5 millimeters on each side. The depth of the door frame should also correspond to the thickness of the wall.

After that, guide metal profiles are fixed to the floor and ceiling according to the markings.

If the partition were made with an arch, then the structure could only be sheathed with gypsum plasterboard sheets, but we are planning to install a door, so the doorway in the partition definitely needs to be strengthened.

To do this, you need to install inside the rack profiles wooden blocks the required section and tighten them to the profile with screws. This will strengthen the doorway, and the door leaf will not sag over time.

How to install an interior door in a plasterboard partition

After the wooden blocks are fixed, the frame is sheathed with gypsum plasterboard sheets and rough and finished.

Door frame installation

You can save on the purchase and make a door leaf from plasterboard, but most likely it is not worth it. Therefore, it is better to buy an inexpensive interior door made of MDF than to go through the trouble of making a door from gypsum plasterboard.

After the opening is ready, a U-shaped door frame is inserted into it, which is made from purchased hardware store wooden profile bars. The bars are screwed with self-tapping screws to the galvanized profile of the opening.

Now you can start fixing door hinges. IN Lately The most popular are two types of loops:

• hinged (overhead) butterfly hinges, which do not require cutting out an area for installation on the door leaf and frame;
• mortise, before installation it is necessary to first cut out recesses for them in the door leaf and frame.

When using hinged hinges, installing an interior door will take much less time compared to mortise ones.

If you prefer mortise hinges, you will have to work hard to cut out the pads to get them neat.

If detachable hinges are used, installation will not take much time. The lower part is attached to the box, and the upper part to door leaf, after which the door is hung.

If the hinges are permanent, you will need the help of a partner who will hold the door while you screw it to the hinges attached to the frame.

Assembling an interior door

After the door is hung, the space between the frame and the opening is foamed, fittings and cashing are installed.

Based on the nature of the materials used, plasterboard partitions are divided into simple and reinforced. In addition, there are options for products with a reinforced metal frame. The type of construction is selected taking into account technical characteristics premises. If the materials used are beams that are shorter than the height of the walls, there is a risk of getting an unreliable and fragile structure. She simply will not be able to hold the partition in the desired angle.

Working with drywall is good because it does not require any specific tools, and everything can be done using tools available to most home craftsmen. However, not everyone can live in an undivided space, and people are starting to build zoning partitions from plasterboard on their own. Today we will look at how to assemble a partition with a plasterboard door with your own hands: We will definitely attach video and photos.
Plasterboard partition with door – optimal solution problems of indoor space zoning, especially relevant for studio apartments. Massive brick walls become a thing of the past: cheap and lightweight drywall, the range of applications of which begins with leveling walls and ends with the construction of complex ceiling structures the most incredible shapes, will allow you to create a partition with your own hands with minimal costs time and effort.

• The first approach is professional. Everything is respected in it technological maps developed by drywall manufacturers. The most famous technological sheets of the Knauf company.
• The second approach is amateur. It is possible due to the versatility of plasterboard profiles.

Plasterboard partition with door, self-installation

This must be done when the partition is built in the bathroom or kitchen. After completely dry primer, you need to, checking the drawing, mark the wall, ceiling and floor. Be sure to use a level to draw clear and even lines.

The materials you will need are the sheets themselves, metallic profile 7.5 cm wide, several wooden blocks, self-tapping screws with dowels, primer, putty and sickle.
You also need to select a gypsum board before building a plasterboard partition with a door. The final stage is installing the door. It is secured with self-tapping screws. The distance between the doorway and the frame is filled with polyurethane foam.

When the entire structure of the plasterboard partition with the door is mounted and lined, you can begin finishing works. To do this you will need:

• The opening is made near the wall. In this case, a continuous metal profile is laid up to the opening on one side. Please note that on the other side it is necessary to leave space for the platband at a distance of at least 100 mm from the corner.
• The door will be located at or near the center of the structure. In this case, the installation of the profile is carried out on both sides of the opening.

How to make a wall from plasterboard and profiles with an opening for a door - instructions and drawings

Development of a partition scheme. Here you should take into account such points. Since you are installing not just a plasterboard partition, but a doorway, you need to choose a place for it in the “new wall.”

In this regard, one should proceed from the specifics of the further use of adjacent premises and their filling household appliances, furniture, and so on. On the other hand, in certain areas you will have to install small fragments of gypsum boards and install jumpers (to strengthen the frame) from profiles. Consequently, materials should be selected according to linear parameters with the expectation that after cutting them, finished “parts” are obtained. The distances from the walls to vertical racks, forming the doorway.

This is necessary to calculate the required length of the lower guide profiles, since the threshold is not made. Consequently, you will have to attach two PN slats to the floor (before the passage). Redevelopment of premises and their zoning are quite often implemented techniques that make it possible to increase comfort in the same “squares”. A plasterboard partition with a door is the most common home renovation option. If you delve into the nuances of such work, then it is quite possible to do without outside help, especially without the services of a professional.

If the partition diagram is drawn up correctly, it is not difficult to find these elements after covering the frame. Alternatively, leave marks on the floor with a pencil or felt-tip pen.

Instructions for installing a plasterboard partition with a door

Despite some shortcomings of gypsum boards, we note that competent creation and correct operation partitions made from this material will help quickly, easily and inexpensively transform the interior of a room, giving it comfort and increasing its functionality. Expert advice: Any construction works using plasterboard should be carried out at a room temperature of at least +15 C. Installation of structures is best done before finishing floors and painting work. Before creating a partition, the surface of the main floors should be leveled, filling potholes, seams and cracks with putty.

• guide profile (UW–75) 3 meters - 5 strips;
• guide profile (UW–75) 4 meters - 3 stripes;
• rack profile (CW–75) 3 meters - 9 stripes;
• plasterboard (gypsum board 1200x3000x12.5 mm) - 10 sheets.

Frame structures covered with sheets of plasterboard have long and with great success replaced partitions made of brick or wood due to a number of characteristic advantages: That’s it, that’s it, the short “theory course is over, let’s move on to the solution” practical issues. Let's look at the list first the necessary tool, we will list the materials that we will need to erect the structure, and also perform an approximate calculation of their quantity.

Plasterboard partition with door: 2 simple steps for a complex design

To increase the strength of the frame, you need to connect the racks with cross members. These are pieces of PS 80 cm long, which are bent so as to form a U-shaped element with a back length of 60 cm and shelves of 10 cm: The first size is the width of the back, the second is the width of the shelf. The table shows that the back width of the two profiles is the same. This is done so that the rack profile can be easily inserted into the guide profile.

If a single-layer laying of plasterboard sheets is used, then self-tapping screws with a length of 2.5 cm are required for its fastening. If it is a two-layer installation, then 4 cm. This takes into account the requirement that the screw must pass through the metal profile to a depth of at least 1 cm. Before building a partition, it is necessary understand that the door will create a load on the rack profiles that form the doorway. Therefore they need to be strengthened.

There are two options here: Now to the question, which profile to choose for the partition? How larger size, those stronger design, so it is better to use profiles with a back of either 60 mm or 75 mm.

Change with your own hands appearance decorating your home is the favorite thing for many owners. And drywall is a material that is a multifunctional tool in matters of repair. It is known what unusual, luxurious ceilings can be made from plasterboard, how gypsum board partitions turn one room into two, how plasterboard sheets are used to construct shelves and niches. Likewise, a doorway can be sheathed with gypsum board, and it can be done on a budget, beautifully and, most importantly, with your own hands.

How to make a doorway from plasterboard with your own hands

A doorway is most often finished with plasterboard during the process of remodeling an apartment. The simplest option is rectangular shape opening, but more and more often owners prefer to add some zest to the interior and give the doorway a curved shape.

The first stage of repair is dismantling old door. A hammer and nail puller will come in handy for this step. First, the door is carefully removed from its hinges, the trim is removed and, in fact, the door is dismantled. If jambs are fixed to the floor, they are sawed off and carefully removed.

After this comes the most important stage - covering the opening with sheets of plasterboard. This process not without some technological features.

Installation of a plasterboard doorway

Work on the construction of a plasterboard doorway is carried out in several stages:

• Rigid frame. This is the basis of the future opening, the structure on which the sheathing sheets are attached. To obtain such a frame, you need to secure a partition from the UW and CW profile systems. UW profiles are fixed at the base of the ceiling and floor - these are the base parts, and vertical rack systems of CW profiles will lie on the sides of the opening.
• To fix the upper dimensions opening, you need a crossbar - it will be placed at the top.
• Height and width the door opening will be determined by the parameters of the box.
• Cutting drywall and preparation of material. Taking into account the dimensions of the door block, as well as the room, the gypsum board is cut out. If there is a need for sound insulation, purchase mineral wool or glass wool.
• Fix sheets Drywall needs to be screwed, lowering the heads of the screws into the base by 2 mm.
• Installation is completed The seams are sealed with sickle tape, putty is applied, and a primer completes the work.

When the surface is dry, the opening awaits finishing decorative finishing.

Creating a doorway from plasterboard (video instructions)

Interior openings made of plasterboard - arch option

An arched interior doorway is a favorite interior design option for many compatriots. This is explained by the geometric perfection of the design, as well as by the fact that installation and finishing are not complicated, and thus you can modify the doorway with your own hands.

Construction of an arched opening:

• Project development. The height and diameter are determined. The easiest way is to make a small sketch on paper, which will then become the basis of a life-size template.
• Installation of metal profile. The U-shaped profile will be the best solution. It is rigid and durable, and is suitable for making arches. The length of the profile is calculated, and cuts are made on the cut part with special scissors (1 cm increments) to shape the frame. According to the template, the profile bends.
• Drywall installation- Preparation. On one side of the strip of drywall that needs to be bent, continuous cuts are made in centimeter increments. The strip is then broken along the cuts, making it possible to give it the desired shape. The bottom of the arch should be the side where the plaster is glued. And on top there will be a side with cuts.
• Arch installation. The surface of the doorway is pre-leveled, and a metal profile is strengthened on both sides of the opening. Using the template, the sides of the arch are cut out. For the sake of control, the sidewall is applied to the place. If one side has come up, the second is being prepared. That is, in this place the first sidewall will be the template. Next, you need to attach the previously curved profile to the installed straight one.

When you screw in the screws, do not press too hard on the screwdriver handle, otherwise the metal profile may bend and the structure will lose its shape.

Plasterboard finishing of a doorway in the form of an arch: types of arches

Interior openings that you can turn into beautiful arches, there are different ones. Some people prefer classics, others want exoticism or originality.

Types of arches and their features:

• Romantic. The corners of such an arch are rounded, and the upper part is straight. Not a very common option, but if you want to save on material, this type arches corresponds to this goal.
• Classic. Such arches are distinguished by their rounded top part, the radius of the arch is half the width of the doorway. Be careful those who are building this arch in a space with low ceilings– such a design will “eat up” the space even more.
• Half-arch. This is either a very small radius of the circle, or only one rounded corner. It fits in any modern interior.
• Modern. Suitable for designing thick floors. Large radius of curvature.

Video instruction: how to make an arch from plasterboard

But what to do if you decide to seal the doorway with plasterboard?

Doorways made of plasterboard: the “stitching” option

This is done in several stages, not so complicated that you can’t do it yourself.

Process step by step:

• Removing the old door and door frame.
• Cleaning the opening.
• The profile is installed on the ceiling of the opening.
• Two side racks are installed at the edges of the doorway, one in the middle (vertical).
• A strip to the size of the frame is cut out of the plasterboard, and it is attached to the metal sheathing with self-tapping screws.
• Do the same on the other side. It turns out that the sheathing is carried out on both sides.

How to seal a doorway with plasterboard (video)

Both installation and dismantling of the doorway are not so difficult. The main thing is to take correct measurements, do not be lazy to make a template, and make all the necessary cuts efficiently and accurately.

A doorway made of plasterboard has many “advantages”, the main ones being that this design is made on your own, and the material used is inexpensive. Try to transform your home in such a simple but effective way.