Looks original and stylish. A loft-style room or other interior design options will look spectacular against its background. Natural masonry is not necessary to create such a finish. You can simulate it. In this case, the masonry can be made on a different basis. under a brick, will be discussed in detail below.

Brick imitation options

Brick wall decoration (photo is presented below) will be relevant for almost any room. The masonry looks stylish and interesting. These walls allow you to create an original, modern interior. However, not everyone has them built of bricks. In this case, you can make an artificial finish. Depending on the technique chosen, it will look more or less natural. There are the following options for artificial brick finish:

• decorative tiles;
• gypsum;
• building panels;
• dye;
• wallpaper;
• Styrofoam;
• decorative plaster;
• drywall.

To choose the appropriate option, you need to consider the features of each of the listed types of brick wall decoration.

One of the popular options is the use of panels. This material has different options for the decoration of the outer surface. One of them is brickwork. These are rectangular slabs that can be made of plastic or MDF. The first of these options is suitable for installation in rooms with high levels of humidity, such as a bathroom or kitchen.

MDF boards can be used in almost all rooms. Since they are made from pressed shavings, it is better to install such panels in dry rooms.

The advantage of panels that imitate brickwork is ease of installation, low weight of the material, and ease of maintenance. If, for some reason, one area is damaged, it can be easily replaced. For this, the plates are purchased with a margin.

Wallpaper and painting

You can decorate the wall of a room with a brick using wallpaper. This is one of the easiest options. In this case, repairs can be done quickly and inexpensively. You just need to choose the appropriate pattern for the wallpaper. Modern printing technologies make it possible to create imitations that are truly brick-like. The surface may even have a masonry-like texture. Each brick will be convex and have a rough surface.

The use of wallpaper with a brick pattern is suitable for finishing even a small room. Its dimensions will not decrease. At the same time, the cost of carrying out repair work will be minimal. It is quite possible to paste over the walls with wallpaper yourself. The disadvantage of this technique is the fact that the finish will still look unnatural. The bricks will not be convex enough. Therefore, it will be noticeable that this is just a wallpaper.

Considering how to make a brick wall yourself, you should pay attention to such an option as a special painting. This technique is suitable for rooms with very flat walls. Repair can also be done by hand. Even a novice master can cope with this task. Painted walls are easy to clean.

Finishing in this case will be relatively inexpensive. At the same time, the paint can additionally protect the walls from moisture. Therefore, this option is suitable for the kitchen, bathroom, loggia.

To create such a decorative surface, you will need to purchase acrylic, water-based or elastomeric paint. Each brick can have a natural color. In some interiors (for example, in a nursery), the masonry can be bright and unusual. Each brick is decorated with colors unusual for such decoration (pink, yellow, blue, etc.).

Of course, a paint coating is not able to create the look of natural brick. However, if this is not required, this option will be one of the most preferable. For finishing, you need to mark the wall by drawing each brick. First, the surface is primed and then painted with a base color. It matches the shade of the mortar between the bricks. Next, glue all the gaps that mimic the lines of the solution. The first coat of paint is applied using a roller. You can manually add shades to the bricks. This will make the drawing look more spectacular.

Tile

Considering options for how to make a brick wall in an apartment, you should pay attention to material such as tiles. Today, many options are available for tiles that imitate brick in their appearance. At the same time, the tile has a number of advantages. Compared to natural brickwork, this finish is relatively inexpensive. Its weight will be less, since the thickness of the plates is small. You can choose a tile design for almost any interior.

Tiles can be made from different materials. It can be artificial or natural stone. Also on sale are clinker and gypsum tiles, which imitate brickwork. The choice depends on the operating conditions of the finish, as well as the budget allocated for the renovation.

Clinker tiles are made from clay and sand. Its surface can be smooth or rough. It is a strong, durable material that is not afraid of various external influences. Most often, this option is used to decorate the kitchen. This surface is easy to clean from various contaminants using detergents.

How to make a white brick wall? In this case, you can use gypsum tiles. There is material on sale that has a different shade. It is an inexpensive, environmentally friendly material. It is suitable for dry rooms.

Tiles made of natural or artificial stone are often used when creating outdoor decoration, for example, when decorating an outdoor fireplace or recreation area on your own site.

Styrofoam

Considering options for how to make a decorative brick wall, you should pay attention to another interesting approach. You can create an imitation of masonry from regular foam. In this case, the masonry will be convex and uneven. With the right finish, you can create styrofoam bricks that look a lot like natural material.

You can create such a finish in almost any room. Polyfoam is a very light material. Therefore, there are no difficulties during installation. It is especially recommended to pay attention to this option when finishing an interior plasterboard partition. In this case, polyfoam will perform the function of not only decoration, but also sound insulation.

Styrofoam bricks can be made quickly. The cost of such finishing will be minimal. To make artificial masonry, you will need to draw lines on a sheet of foam plastic that will delimit each individual brick. The material is cut with a sharp knife.

When the required number of blocks is cut, they are glued to the wall. A distance is left between each brick. After that, the surface is painted. You need to choose a coating that will be compatible with the artificial material.

You can make a similar finish from drywall. The technology is the same as when using foam. Plasterboard blocks are glued on a special composition on a gypsum base.

Decorative plaster

You can make a brick wall from plaster. This option looks impressive in the interior. With the help of this material, convex, textured surfaces are created. At the same time, the creation of such a coating does not cause difficulties.

Applied to the surface. In this case, it is not necessary to perfectly align the walls. They may have minor defects. The finish will be durable. It is laundered with household products. You can do this with your own hands. This significantly reduces the overall cost of repairs.

In addition, imitation stucco brickwork is a good insulation. Heat loss in the room during the cold period is noticeably reduced. Moreover, the owners of an apartment or a private house can choose the texture, color of decoration on their own.

When creating a plaster brick wall decoration, you can choose different shades. The texture can be very different. The final result will depend on her choice. The surface of each block can be rough or smooth. Interior design using this technique can be created in accordance with the latest fashion trends.

The disadvantage of plaster finishing is the fact that its surface is clogged with dirt, dust. Therefore, it is better not to use such materials when decorating the kitchen. In rooms, such surfaces can be easily washed using ordinary household chemicals.

Making decorative plaster bricks

Brick wall decoration can be made from And you can create them yourself. This is a creative, fun process. First you need to make the shape. It is made of silicone. Each decorative brick should be 5 to 20 mm thick. To create a shape, you need to make a base model from a solid material. It could be a real brick. It is coated with petroleum jelly, and then a layer of silicone. You can make a form with which several decorative bricks will be poured out at once.

When this stage is completed, you can start mixing the solution. Dry gypsum is mixed with water. You should get a thick mass. The form must be greased with soapy water or petroleum jelly. Next, gypsum is poured into it. This should be done carefully. The fill is leveled by drawing a regular ruler over the surface. Plaster hardens within 30 minutes.

After that, the form is carefully turned over, taking out the blanks. The result is white decorative bricks. They can be painted in any other shade. The white wall also looks interesting in the interior.

There is a simple technique on how to make a brick wall from a similar material. It is glued to a special compound (you can purchase glue for tiles). Using a notched trowel, the composition is applied to the surface. Next, each homemade block is glued to the surface.

Preparing the wall for finishing

It is quite possible to make brick-like walls with your own hands. Step-by-step instructions will help you with this. Before starting the decoration, you will need to properly prepare the base of the walls. To do this, you need to remove the old wallpaper, helmet or other material. When this procedure is performed, the surface of the base is thoroughly washed. If it is wallpaper, take it off. Old plaster also needs to be removed.

When the surface of the wall is prepared, you need to assess the extent of its damage. If the irregularities are large, they should be repaired with putty. If painting or wallpapering will be carried out, you need to create a perfectly flat surface. For this, a layer of starting and then finishing putty is applied.

When the surface is leveled, it needs to be primed. This is necessary for strong adhesion of the adhesive to the substrate. The primer may include antiseptic components. They prevent the development of mold under the finishing material.

There are different primers. They are designed to be applied to different types of substrates. There are the following types of primers:

1. Acrylic. Suitable for concrete, cement, plywood and wood walls.
2. Glyphatic. For use on metal and wood surfaces.
3. Alkyd. For wooden walls.
4. Perchlorovinyl. Suitable for concrete, metal or plaster surfaces.

Having chosen a suitable composition, it is applied in two layers. The first time a primer is applied, leaving it to dry completely. Next, you should process the walls again. After that, the surface becomes ready for further finishing.

Finishing work

Studying how to make brick-like walls in the interior, you should use a simple instruction. After preparing the base, it should be drawn. A straight line is drawn at the bottom. At the same time, you should not be guided by the floor level. A building level is applied for this work. The wall is delimited, leaving the required distance between the blocks.

The material chosen as a decorative brick must be covered with an adhesive on the reverse side. Next, according to the marking, the block is glued to the wall. First, lay out the first row from the bottom. The next row is staggered. The material from which decorative bricks are made usually does not weigh much. Therefore, it is not necessary that the blocks rest on one another.

After all the elements of decorative masonry are glued to the base, you can paint the seams in the selected color. This must be done carefully. In the course of work, a thin brush is used.

Application of plaster

When deciding how to make a brick wall in an apartment, many owners prefer plaster. You can create a textured surface from it. The markup is also generated first. The seams between decorative bricks are painted with paint of the desired color. When it dries, the surface of the wall is covered with construction tape. Special thin tapes are on sale. They are glued first along horizontal lines.

When this work is done, plaster is applied to the wall. The mixture should be fairly viscous so that it does not run or slide off the base. Pigment can be added to the composition if desired. The surface of the wall must be rough. You can also make the finish smooth.

Completion of work

How to make a brick wall from plaster? After carrying out the necessary preparation, the composition is applied to the walls from bottom to top, evenly distributing it over the surface. You need to work quickly so that the plaster does not have time to harden. After that, while the layer is still semi-wet, you need to carefully remove the masking tape. At the same time, they pull the horizontal lines. The vertical bars will also be pulled out of the solution. After this, the finish should dry well.

It can be made easier. A layer of plaster is applied to the prepared wall. Until it is completely frozen, using a knitting needle or other sharp object, markings are cut out on the surface in the form of bricks. Sand the edges with a dry brush for a more natural finish. After that, the space between each drawn block is painted. This must be done carefully so as not to go beyond the lines. The surface of decorative plaster bricks can be varnished or painted.

Having considered how to make a brick wall, you can create an original, stylish interior. The room will look interesting and unusual.

There are various options for imitating brickwork with your own hands. They allow you to create a surface that will completely repeat the brick coating. This makes it possible to bring exceptional design ideas to life, creating an interior that will be filled with beauty and comfort.

Do-it-yourself imitation of a brick wall is performed in various ways. Some of them require the necessary skills, others are almost ready-made options. Each method is suitable for a specific case.

Ready views

Currently, there are ones that completely repeat the texture of the brick. The advantage of such products is their low cost and ease of installation, which differs depending on the type of product. The following options will be highlighted:

All options have their advantages and disadvantages, but there are ways to make an imitation of brickwork - exclusively with your own hands.

Corrugated board application

The use of corrugated cardboard sheets is a rather peculiar way that makes it possible to create a decorative surface, spending a minimum of materials for this. Work requires the following components:

• Directly cardboard. You can use boxes for household appliances. The main thing is that their density is not low.
• High-quality paper napkins (firm, non-torn).
• PVA. For work, you need a large amount of glue.
• Handicraft gun (refueled with hot melt glue).
• Stationery knife, ruler and pencil.
• Paint and varnish. For the final stage of finishing.

Materials required for the manufacture of brick inlay from corrugated cardboard

Advice! Thin cardboard is not the best solution. It will not allow you to create the necessary texture. If it is not possible to use a thicker material, then you can go for some trick. It consists in the fact that the fragments are glued together to create the required thickness.

To imitate brickwork from corrugated cardboard, it is better to use dense material

The technology consists in a sequence of actions:

Thus, it is possible to form a decorative brick wall with our own hands, which does not require large financial costs.

Finished Corrugated Masonry

Using a stencil and plastering pattern

This is a simple option requiring only the utmost care. The work is as follows:

• A layer of plaster is applied to the surface. The thickness should be more than 4-5 mm, otherwise you will not get an expressive texture.
• Next, a stencil is taken. It can be rubber or plastic.
• It is well moistened with water so that the main side does not stick to the wet solution.
• The stencil is applied to the surface and pressed. It is necessary to remove it from the wall carefully, because with sudden movements you can remove part of the mixture.
• The procedure is repeated. It is important to keep in mind that the horizontal lines must match. If this is not followed, then fragmentary areas are obtained, unrelated to each other.
• At the end, the imitation brickwork is well primed and waxed. The seams are embroidered. The surface is painted with acrylic paints.

On a note! To create a more interesting effect, color is added directly to the plaster. Then it is possible to create a play of shades, because the joints are painted in other options. Do not forget that if you paint the wall directly, then after drying, the shade will become slightly darker.

A brick wall with your own hands from fresh plaster can be obtained without using a stencil. The technology is as follows:

1. Lines are drawn on the surface to indicate the seams in the brickwork. This is done a bit arbitrary to make it look more natural.
2. With the help of a narrow scraper, the plaster is removed. The joints are immediately rubbed with a dry brush. This will shape the relief and also smooth out the bricks a bit.
3. The finished wall is primed and painted.

These methods allow you to decorate only a newly made layer of plaster. If, after applying the plaster mortar, some time has passed, and it managed to dry out, then it will not work to create a brick wall using the above methods.

Putty bricks

This option is used when the idea of ​​creating a wall for a brick came some time after plastering. In this case, for its implementation, a putty is used, which is pre-painted in the desired color.

Brick-like wall made of putty

The general procedure is as follows:

• The wall is well cleaned of dirt and dust. Degrease if necessary. A layer of primer is applied.
• Marking is made on the surface. It should repeat horizontal and vertical seams so that an imitation of brickwork is obtained.
• The joints are painted over with the selected color and left to dry completely.
• Next, masking tape is glued. Its stripes should follow the painted seam lines. This is done like this: first, the horizontal lines are pasted over, and then the vertical ones (they should go over the previous ones).

Marking with masking tape for brickwork

• A thin layer of putty is applied to the surface. The required texture is formed immediately, so the layer is made uneven. You can use additional tools to help you create the relief.
• The mixture is left for a while, it should set. Now they remove the tape. This is done very quickly, because the segments are fastened together. The putty is left to dry completely.

• The layer imitating a brick wall is additionally sanded, creating an original texture.

Thus, all work is done exclusively by hand. It is possible to form an excellent decorative surface, which will be the highlight of the interior. But you need to read that the question of how to make imitation of brickwork has not only a technical side. It is much more important to correctly fit it into the decor of the room, so that there is no unnecessary severity, thoughtlessness.

Reading time ≈ 4 minutes

One popular interior decorating trend has been picking up steam lately. We are talking about such an interesting option as imitation of a brick wall - of course, many have already encountered this phenomenon more than once. Imitation - because, in fact, the wall is not brick, but simply finished in such a way that an appropriate impression is created. In this article, we will consider all the stages of how to simulate a brick wall with your own hands (see video, photo).

Markup

The first step is to prepare the walls for further processing. To do this, you need to thoroughly clean the surface: the wallpaper is peeled off, leveling is done, and irregularities are smoothed out (using sandpaper).

Next, a "model" of a brick will be needed. You can cut the end of the alleged brick from cardboard or a piece of linoleum (there are other options). Dimensions 25 x 6.5 cm are standard. It is necessary to mark the seams; indent - 1.5 cm around the entire perimeter of the workpiece from the outside. One more seam is needed in the middle - to make it look like two halves of a brick. Further, it will become clear why you need to do this.

You need to lay out the "bricks" from floor to ceiling. We retreat from the bottom 5-10 cm. Then we use a simple pencil and outline the first corner "brick".

The general technology is as follows: you need to start tracing from the corners of the wall, since these places are the most difficult, then along the edges, then we move to the center.

You can watch this process in more detail in the video.

Primer

Further, to create an imitation of a brick wall, you will need a primer; it is recommended to use a non-concrete contact one. It is diluted in a standard way, then the solution is applied to the wall using a roller. This is done so that the mixture lies clearly and firmly. This process will not affect the markup - there is nothing to worry about.

Application of the solution

Masking tape is applied to the wall, moreover, at the junction of the "bricks". It is recommended to glue the horizontal lines first, and then move on to the vertical ones. It is necessary to overlap the sticker.

We make the mortar from tile glue and plaster (50 to 50). It should be noted that an imitation of a brick wall in a plaster apartment is not only a simple, beautiful, but also a reliable finishing option.

Then the plaster is applied with a spatula (or even by hand, as it is easier and faster, but do not forget to use special gloves in this case).

This moment is very important, because if you wait, you won't be able to rip it off. In principle, this is the main secret of the technology. There are some more nuances - it is impossible to use gypsum in this case: it dries instantly - and it will not be possible to completely free up the space between the fragments.

Shaping the bricks

Next, you need to discuss another important point, namely, giving the form of imitation of brickwork. There are many ways, but the easiest one is to use a chisel, spatula, or tablespoon. This action must be carried out if the solution was applied by hand (that is, unevenly).

Surface preparation for painting

First you need to clean the surface: sweep away the dust with a broom, use brushes, paint brushes, sandpaper.

When performing repairs, quite often there is a desire to arrange a brick wall with your own hands. This work can actually be done using conventional plaster mixes. It is very important to choose the right place where such an accent will effectively emphasize the individuality of the interior.

When choosing the type of interior decoration for your home, you have to take into account many factors. A brick wall is one of the ways to follow the fashion trend. This type of decor can be performed on an entire wall or on a separate area (arch, niche). "Bricks" play the role of an accent in the interior of the room.

Preparatory work

Before finishing, you should prepare the surface on which you plan to apply the decor. You must first remove the old coating. The thickness of the finishing layer created can be up to 1.5 cm. The imitation brick for interior decoration looks good on exceptionally flat walls. Therefore, it is necessary to check their quality level. If the deviation exceeds 2 cm / m, then the surface must be leveled with beacons (cement mortar). Leave for several days until the mixture is completely dry.

The smooth surface on which the plaster will be applied should not contain large depressions and bulges. Any defects should be repaired with a mixture. Prepared for finishing, the dried wall must be covered with a suitable primer. Without this, the solution layer can flake off over time. A primer for brick walls for plastering is selected according to the base material. It is convenient to apply the liquid with a paint roller, and in corners and other hard-to-reach places it is necessary to brush thoroughly with a brush.

After the primer has dried, the plaster is mixed. When preparing the material, the consumption of the composition should be foreseen. If the layer is laid with a thickness of 10 mm, then 8-9 kg of dry mix is ​​required for 1 m2 of surface. Standard bags are packaged in 30 kg. This amount is enough for a 3.5m² wall section. It is recommended to cover the floor with foil so as not to get dirty. The solution should be mixed with a drill with a special nozzle. The mixture should be quite thick and viscous. If you do not plan to paint the finish, then the solution can be tinted.

Brick wall decor will look absolutely natural if the seams are drawn with a special tool (jointing). But you can use another handy "tool" (broken pencil, thick knitting needle, etc.).

Create a simulated brickwork

If it is planned to cover only a section of the wall with plaster, then work should be started by applying markings:

• it is necessary to draw the finishing borders with a pencil according to the level;
• stick masking tape along the lines.

For working with plaster, two steel trowels (20 cm, 5 cm) are used. With a narrow tool, the mixture is applied to a wide one. Also small defects (protrusions, pits) are corrected with a small spatula. With a wide spatula, the base is smeared with gypsum plaster (starting from the edge), the layer is leveled. The work is carried out in separate sections, their area depends on the volume of the prepared solution (up to 15 liters are mixed at one pass). Achieving a perfectly flat surface is not worth it (natural brick does not happen like that). You can use a brick plaster stencil to apply the seams.

To draw a brick pattern on a decor, you should familiarize yourself with two technologies:

• cut the seam with a scraper;
• mark and stick masking tape before applying the solution.

Drawing seams with a scraper

In the first case, plaster brickwork is drawn after applying the solution. A rule or level (1.5-1.8 m long) is applied to the dried surface of the decor. The seams are marked with a sharp plate (the optimal width is somewhere between 0.5-1.0 cm).

The vending "drawing" of the masonry is performed based on your own preferences. Marking on the wall should be done with bandaging the seams. It is necessary to take into account the dimensions of a classic brick (250x 65x120 mm). Today, an elongated wall material is produced, or almost square. There are also embossed, textured, specially chipped and various non-standard products. You cannot draw any seams on the wall, then imitation of brick from plaster will not work out naturally.

After that, you should take a scraper, a narrow chisel, or some kind of homemade tool and carefully draw along the drawn lines, removing the plaster. This is how the seams are formed, the depth of which is 3-6 mm. It is not very convenient to do this work with a simple chisel. Excess mixture at the seams forms a "fringe", it should be constantly removed.

For a neat formation of seams, you can use jointing, it gives a convex or concave relief. A stucco brick wall is drawn starting with horizontal lines, and then short vertical lines are made. After the decor gains strength, all the imperfections of the pattern should be removed. Excess mixture formed on the bricks after the formation of the seams must be immediately removed with a dry cloth. You can walk along the edges with a damp sponge.

It is important to have time to apply the drawing before the plaster is completely dry. Otherwise, the "bricks" can be damaged. Therefore, it is recommended to process the surface in sections. After complete drying, the decor should be painted:

1. First, the entire surface is tinted.
2. Then a narrow brush should carefully go through the seams.

Forming seams with masking tape

There is another way how to make plaster bricks on the wall. In this case, future seams are marked with a pencil over the entire pre-primed, trimmed surface. Short vertical lines should be offset in relation to the top (and bottom) row by half a brick. Masking tape is glued along the markings (first horizontally, then vertically). If this process is done differently, the tape will be difficult to remove. Its ends are brought out beyond the border of the processed area.

On the surface prepared in this way, the solution is applied with a spatula. It is quickly leveled, the degree of surface smoothness can be chosen according to your wishes. It depends on whether you like embossed bricks more or absolutely even ones. After that, without waiting for the solution to dry, gently pull the ends of the horizontal adhesive tape, which leaves a pattern of seams on the decor.

Do-it-yourself imitation of a brick wall from plaster requires some experience. Therefore, it is recommended for beginners to form a drawing in the first way.

To add severity, dried "masonry" can be wiped with a stiff brush. If you walk over a completely dry wall with sandpaper, the surface will become smooth. After that, the decor is ready for coloring.

When the wall finish for a brick is made and the surface has acquired the required hardness, all unnecessary (residual mortar that violates the pattern) should be removed. The features of the finish depend on whether a colored (tinted) mixture was used or a regular one.

Decorative plaster should not remain white-gray. Therefore, a colorless wall should be painted by mixing several different shades, or stay at a ready-made tone. In this case, it is necessary to take into account the interior design and lighting features. The wrong color can ruin the whole experience.

Advantages of masonry imitation

Do-it-yourself brick wall decoration has a number of advantages:

• performance of work does not require special financial costs, time costs, professional knowledge and special skills, you need accuracy and diligence;
• you can choose the material based on your own preferences and financial capabilities (plaster, any additives, paint of the shade you like);
• plaster mixes are environmentally friendly and will not harm health;
• imitation of brickwork has good thermal insulation performance;
• the finishing layer is quite thin, due to which the space of the room does not decrease;
• a brick wall made of plaster does not require special maintenance, and will not need repair for a long time.

"Brickwork" in a modern interior

A brick wall in the interior is carried out in the design of the loft style. This method makes an effective accent. You cannot overdo it and finish the whole room "like a brick". You can give the following options for creating accents:

• the space around the opening, niche, arch, door, window, mirror is formed, this solution looks quite attractive;
• the wall is decorated with separate, scattered on the wall, "bricks", in this case the surface does not resemble real masonry, but an original decor is obtained;
• finishing one entire wall, this approach is a classic accent in the room, which is done where all the attention is paid, for example, the wall behind the TV or fireplace.

Small flaws
This type of finish can be disappointing:

• in a very modest room, where it is important to keep every centimeter of free space;
• this surface attracts dust very much, which can be easily removed with a damp sponge, but this should be done quite often;
• repairs may require additional financial costs if, before making a brick wall from plaster, you need to level the base.

But no matter what, this type of interior decoration is very popular.

Brickwork brings in the interior a unique charm and the very "zest". And if the outer cladding of a building can still be done using various types of bricks, then indoors, especially in an ordinary apartment, it is not always possible to use such a heavy finish, because additional loading on structural floors can lead to extremely unfavorable consequences.

However, there is a way out - you can create a wonderful imitation of a brick wall. There are several options for such a finish, and you can handle each of them with your own hands. The final result depends solely on your imagination and personal preference.

Before starting work, prepare the fixtures necessary for making decorative "brick" cladding. The list will vary slightly depending on the finishing method you choose, but in general you will need the following:

The simplest version of imitation of brickwork

The easiest to manufacture option for imitation of brickwork is to draw the corresponding elements of the cladding on a plain wallpaper or simply a painted wall.

Of course, in this case, there is no question of the realism and "bulk" of the masonry, however, the method has a number of great advantages, namely:

The disadvantage, as already noted, is the unnaturalness of the facing. And the finished result looks, to put it mildly, not very attractive. Therefore, it is recommended to use it only in some utility and household premises such as a dressing room, garage, etc.

For living rooms, choose a more effective method of imitating brickwork from the following ones.

Using masking tape, mark out the bounding paths

We mark the window according to the template with a narrow masking tape and paint over with "brick" acrylic

Homemade gypsum bricks look just as good as factory-made trims. The implementation of such a facing does not require the performer to have special skills and large financial costs.

The first step is making a mold

Make a mold for making bricks. The thickness of an individual element can be 5-20 mm. At a lower height, the bricks will quickly break, and the use of large-sized elements will lead to a significant increase in the consumption of plaster for grouting. In addition, too large bricks will visually reduce the area of ​​the room.

The second step is preparing the solution

Prepare a solution for the manufacture of cladding elements. To do this, dilute dry gypsum with water to a state similar to thick sour cream. Lubricate the form prepared at the last stage with soapy water or simple petroleum jelly and pour the finished mass into it.

Align the fill using an ordinary ruler. Leave the mold for 20-30 minutes, then turn it over and carefully remove the finished cladding. Paint the brick the desired color. Sometimes, to obtain the required shade, the product has to be painted in at least three layers. You can varnish the brick if you wish.

The third step is cladding

Start simulating brickwork. To do this, apply the markings to the section of the wall set aside for finishing. At the bottom of the wall, set aside the starting line from which you will begin laying the plaster stones.

To fix the bricks, use an adhesive specially designed for this type of work, such as tile adhesive. Buy it from a related store.

Lay the first row of bricks in accordance with the selected joint width. Fasten further rows in a checkerboard pattern. Use a notched trowel to apply the adhesive to the wall. For more effect, you can gently break off the outermost bricks in each row to make their edges look torn and uneven.

Leave the finish to dry for 1-3 days. You can check the exact drying time of the glue on the package.

Imitation Styrofoam Brick

An imitation of a brick wall can be made from ceiling foam tiles without a pattern. The recommended size of the "bricks" is 150x70 mm. A cladding made of elements with larger dimensions will look unnatural. The procedure for making bricks is extremely simple.

First step. Lay out the tiles. An ordinary gel pen will help you with this. Do not forget to leave small allowances for the tile joints.

Second step. Use a toothpick to push in neat, straight lines along the markings.

Step three. Make a crush. Take a lid from any tin can and cut an even strip out of it. Cut off the edges from one edge of the strip, making a "sting" no more than 2 mm wide. Use this tip to push the marking lines to the end.

Fourth step. Cover the selected section of the wall with ready-made bricks. Use tile adhesive for gluing. Start the cladding at the bottom edge of the wall. The seams do not need to be filled. Leave a 1–2 mm gap between the bricks.

Fifth step. Paint the finished veneer. Apply more paint to the gaps. This will create the most realistic imitation of brickwork.

Wood bricks

Imitation of brickwork can be done very easily out of wood.

First step. Buy material for making "bricks". You can use plywood, for example.

Second step. Cut the workpiece into the required number of rectangular pieces of the same size.

Step three. Sand the front of each piece.

Fourth step. Prepare the markings on the wall.

Fifth step. Lay out the bricks according to the markings, starting from the lower opposite corners. Attach the elements at the same distance corresponding to the seam thickness you have chosen. A gap of a couple of millimeters will be sufficient. Lay out all the bricks.

Sixth step. Paint or varnish the finished masonry.

The advantage of imitation of a brick wall made of wood is environmental friendliness and impressive durability.

Decorative bricks can be made with dry tile adhesive.

First step. Dissolve the dry component in water until a mixture is obtained with a consistency close to very thick sour cream.

Second step. Divide the resulting mass into 3 approximately equal parts and add a small amount of paint to each of them. Coloring components should have a different shade.

Stir each pile thoroughly. As a result, you will get a lot of beautiful and interesting divorces.

Step three. Roll each pile into a "pancake", and then cut the resulting product into identical bricks. Let the elements dry.

Repeat the above steps until you get the required number of bricks.

Fourth step. Cover the wall with finished bricks. Use tile adhesive to fix the elements.

Fifth step. Fill the seams with a specially formulated compound. It is best to keep the core slightly darker than the cladding.

Sixth step. Cover the finish with a couple of coats of varnish.

Finishing decorative cladding

First step. Mix red and light ocher.

Second step. Add some whitewash to the mixture.

Step three. Treat decorative masonry using the tampon method. To do this, take a sponge, dip it into the thick mixture prepared in the previous steps, and evenly distribute the composition over the lining.

Fourth step. Take liquid paint that is brown or close to it. Spray paint over the veneer with a toothbrush.

For a more dramatic and natural look, you can use a different color technique for each row. For example, you can treat the second row of masonry with hematite with cold diluted water, cover the third row with a mixture of sienna and white, etc. Apply all coloring compositions according to the same tamping technique. Alternate shades in order.

Finish off with a couple of coats of varnish on the imitation brick wall. If you want to give the veneer a matte surface, gently sand it with fine-grain sandpaper.

You don't need to be a great master to create an imitation brick wall yourself. Choose the method you like the most and start finishing in accordance with the instructions.

Happy work!

Video - Imitation of a brick wall with your own hands