Grill scoop dimensions. DIY metal barbecues: sizes, photos and ideas for different models. Barbecues for insertion are equipped

Accessories for fireplaces make it easier to control the fire and make the use of this heating device safe, because thanks to them, your hands do not come into contact with the fire, and also, for example, you can quickly remove rolled out coal from the floor.

Accessories overview

Scroll accessories for the fireplace big enough. The most popular of them are included in the standard fireplace set. It always consists of:

Pokers.
Shchiptsov.
Scoop.
Panicles.

Poker for Russian stove and fireplace allows you to change the position of burning wood. It may look like a simple metal stick with a thick end or a stick with a hook. It is also given the appearance of a spear with a hook.

Using forceps, perform similar actions. However, they are the best "jeweler" because they allow you to take and rearrange a log or coal. Most often they are used to pick up those coals that have rolled out of the fireplace or stove fireboxes.

Sovcom take the ashes from the brick fireplace and, and pick up coals from the floor. True, in the second case they always use a broom. It is also used to clean the floor around the fireplace.

This is a standard fireplace set always hung on the wall or mounted on a special stand. In the first case, it looks like a horizontal bar with hooks. In the second - a view of the base with a stand attached to it. The latter may have hooks or two arches, into the middle of which each element included in the fireplace set is inserted and on which rests.

Also in demand are such fireplace accessories as:

Firewood stand.
A container or stand on which fireplace matches or a fireplace lighter are placed.
Fireplace lighter or special matches (the first is better because it speeds up ignition).
Mesh or protective screen.

Almost all of these fireplace accessories can be made with your own hands. The exception is lighters and matches. As for the material, the fireplace set can be made of steel, brass, copper and cast iron.

Brass and copper fireplace accessories are best suited for electric fireplaces. In this case, they perform only a decorative function and become covered with soot and soot. If you use brass and copper accessories in the fireplace made of brick, they need to be cleaned constantly.

Scoop

For a fireplace, the same scoop that is used for a Russian brick stove may be suitable. To create it it is recommended take sheet steel 0.5 mm thick. The main part of the scoop included in the standard fireplace set is made from it.

Forceps

You can make fireplace tongs with your own hands in the form:

Scissors.
Tweezers.

The second version of the element included in the fireplace set is simpler. To do this, you need to take one long or two short metal strips with your own hands. Further actions the following:

The strip is heated in an oven until reddened and left to cool.
The long strip is folded in half. The fold should resemble a circle, from which two straight lines extend in one place. If there are two strips, then they are fastened with a rivet and then bent. The curve should resemble a heart.
Twist both ends around the axis as described above.
Chop again and cool in oil.
Apply a layer of black paint.

Poker and broom

The metal for the poker included in the forged set for a brick fireplace or Russian stove is processed with your own hands in the same sequence as tongs. Features of the manufacturing process:

First, one end of the round rod is pulled onto the rectangle and a small curl is made on it. After on the fork ( special device for an anvil) bend the handle.
A similar curl is made at the other end. Next, the workpiece is bent so that the plane of the curved end is perpendicular to the main part of the poker included in the fireplace set. The fold is also made on the fork.
Perform twisting.

The poker itself should be such that its length is 50-70 cm. If it is shorter, moving coals in the firebox of a brick fireplace or Russian stove will be dangerous

Regarding such an element accessories for stoves and fireplaces made of brick, like a broom, then you can make it with your own hands almost like a dustpan. More precisely, you only have to make the handle. It is better to look for the main part with pile in the store. A brush with long pile. True, the pile must be fire-resistant. After purchasing the brush, the handle is attached to its base.

If you don’t want to make a broom with your own hands, You can use a fireplace vacuum cleaner instead. This option is better, because cleaning will not be accompanied by the release of dust. Today, many people include it in their fireplace set.

Firewood stand

Firewood stands can be made from pine boards, plywood, metal strips and rods. Also, such fireplace accessories can be made from other materials.

What could it be better than rest outdoors with your family or close friends. Obviously, dishes cooked on an open fire are much tastier and more aromatic than on a regular gas or electric stove. After all, the aroma of fried meat or fish is mixed with the smell of smoke and firewood. Definitely, a barbecue is best suited for these purposes, especially since making one with your own hands is not at all difficult.

For ease of use of the barbecue, you definitely need various devices, including a poker.

Why is it needed and what is its convenience?

Poker – indispensable element, where coals or firewood are used, that is, when working with a barbecue, stove or fireplace.

Of course, you can stir the coals using improvised means, but it’s much more convenient to do this with a poker:

It has a comfortable handle to hold it.
Its length allows you to avoid burning your hands.
The end of the poker can not only rake coals, but also split firewood and pull excess logs out of the fire.

In order for the meat to cook evenly, the coals must lie level, so you have to constantly move them

How to choose a ready-made

A poker is selected according to several criteria:

By material: bronze and steel are considered the best. Light metals and cast iron will not last too long.
Length: selected according to the person’s height.
By weight: the poker should not be light, but at the same time you need to choose one so that your hand does not get too tired while working at the grill.
According to the manufacturing method: experts advise purchasing hand-forged products.

How to do

There is nothing easier than making a grill poker yourself, especially since there are currently no problems with the material for manufacturing. There are several options for using material for making barbecue fixtures:

fittings,
rod,
metal plates.

There are two manufacturing methods:

forged in a forge;
made by electric welding.

A novice blacksmith will be able to forge a poker for a barbecue, and at the same time he will have the opportunity to practice before performing more complex work in the forge. Equipment you will need is a blacksmith's forge, a small anvil and a hammer.

What is a grill poker made from? Most often this can be a metal rod with a diameter of 8-12 mm. The rod is heated in a forge, the tip of the workpiece is flattened on an anvil with a hammer, then bent to the desired shape. If it is not possible to do this in a forge, then you can freely heat the metal in a fire until red-hot and also bend it with a hammer to the required result.

Making a poker using welding is not at all difficult; for this you need:

take a metal square with a diameter of also 8-12 mm;
bend and weld the handle to the desired shape;
beat with a hammer on an anvil and cool in water;
then clamp it in a vice and rotate it several times.

That's what came out of it:

Using one of the methods described above, you can make the simplest poker for a fireplace using ordinary fittings with a diameter of 10 mm. If you have the simplest tools this will be very easy to do.

For almost any man who is familiar with metal, it will not be difficult to make a poker with your own hands

All barbecue accessories that are manufactured with my own hands, will delight you and your loved ones for many years, thanks to the fact that a lot of positive energy and emotions are invested in them.

Eh... How many of them my father remade in his time! For every taste and for any purpose. Both for raking out ash and for grain and flour. I remember he did it without welding and without a drill and without bolts. Hands grew from that place...

I would like to offer several of the most popular options.

Option for a scoop for removing ash. As source material Any metal about 2mm thick can be used. It can be galvanized or simple wire rod and aluminum. What is at hand in one word. The picture shows approximate calculations. Typically the size of the scoop should fit in the furnace vent.

We cut the metal according to the template, bend it and secure it with rivets. The handle is made from the same material. We bend it for greater stability, as shown in the figure, and at the place of attachment to the scoop, we rivet it a little - to capture most of the scoop. We attach either with rivets or bolts.

Option two is a grain scoop.

Typically, scoops for grain, flour and other bulk products are made in this form. That is, rounded. It's easier to make them.

But again, metal is needed. Although nowadays it can be replaced with plastic, in those days it was not.

So, use a jigsaw to cut out a semicircle from the board. As a handle, you can choose either wood or any other material, for example PVC pipe, suitable size. We attach the handle to the base, and cut out the scoop itself from metal, which we nail or take with screws to a semicircle from the board. That's it - the scoop is ready.

Well, another option is modern.

It can be used everywhere except elevated temperatures and various chemistry. And you can make it from plastic canisters with a similar configuration.

Do-it-yourself metal barbecues are a mandatory attribute of private households. Dimensions and photos of individual product options will help you create a unique design yourself. Useful designs often used for outdoor picnics and recreation. It will help you to make a product yourself finished drawing with everyone required sizes, which is used in this work as a sample.

A durable and beautiful grill will decorate the entire yard

Read in the article

What types of barbecues are there?

Simplified DIY metal barbecues have the shape of a rectangular body. Dimensions and photos of the devices are presented in this review. Coals are placed inside the container, which creates the necessary heat. There are a significant number of products that differ from standard models.

The following types of barbecues exist:

stationary are massive structures that are placed on a rigid base. Metal devices can become beautiful and stylish element. Such models are distinguished by their durability and variety;

Stationary barbecues

portable ones are characterized by compactness. They have less weight and are easy to transport by car. Portable products are made of thin metal, which quickly deforms;

Grillkoff Standard

collapsible models are popular due to their quick conversion into a compact form. Collapsible design characterizes the possibility of quick disassembly and assembly;

Brazier TONAR collapsible

mobile options are designs large sizes, non-collapsible variety, equipped with wheels for more convenient movement around the territory. Do-it-yourself metal barbecues are decorated with stylish decorative details. The sizes and photos of these structures vary.

An electric unit equipped with a function for automatically moving skewers has certain properties. In such a device, food is fried evenly. In full electric models Hot spiral elements are used instead of coals.

spit for barbecue

Metal structures have the following advantages:

they can be easily transported, cleaned and disassembled;
you can make the iron device yourself;
The metal retains heat perfectly, which allows you to fry the meat evenly and quickly.

Other sizes are selected based on individual preferences:

the width should correspond to the size of the skewers and be 8-10 cm smaller;
the length depends on the amount of kebab that will be fried at the same time. The distance between the skewers should be 7-9 cm. Special recesses are made for the skewers along the long side;
When choosing the size of a metal barbecue grill, you need to consider the height of the legs, which depends on individual preferences. For portable devices they are small. Welded structures have high legs;
The thickness of the material depends on the type of structure. U stationary device it can be 3 mm or more. And for a portable product, it is better to choose a material with a thickness of about 2 mm.

In some models, a second plate with longitudinal holes in the form of grates is placed on the bottom. This protects the metal at the bottom from burning out.

Step-by-step instructions and features of drawings of metal barbecues with dimensions

We build original barbecue devices with our own hands from metal. To do this you will need dimensions with a roof and detailed photos certain models. The collapsible model includes four legs, perforated walls and a bottom. Before installation, you should prepare a steel sheet, grinder, drill, fasteners and corners.

Standard assembly of the structure consists of separate stages:

Image	Stages of work
	Marks are made on the metal for the bottom and walls of the planned structure.
	The future shape is cut out along the outlined lines .
	The edges are bent and welded. Perforation holes are made using a drill.
	Chamfers are made in long walls.
	It is most convenient to make the legs from a corner, sharpen them at the bottom and weld them to the box.

The grill is made from a barrel or gas cylinder. In addition to the container, you will need a grinder, a drill, metal corners and a welding machine. First, markings are made and the upper area of the barrel is cut out. The end sections remain in place. A lid is made from the top part. The legs are made from corners. They are welded to the ends of the barrel.

Supports for skewers are made from the corners. They are welded to the inside of the product. Handles should be welded to the lid.

Helpful advice! The legs can be made from twigs. At the same time, the thread is cut and the nuts are attached. You can connect elements using bolts, which allows you to create a stronger structure.

The nuances of manufacturing collapsible options

It is easy to make dismountable installations from metal. Photo shows interesting solutions.

This design does not require welding equipment. But you will need drills, a drill, a steel sheet, nuts and angles. Just like with the non-separable version, a drawing is made and elements are cut out from the steel plate. The prepared frame is bolted to the base. For a strong connection, it is recommended to use engraver washers.

Legs are mounted on the base of the device. Pipe sections are placed on prepared pipe supports. The sides are connected using bolts. To increase the strength of the structure, it is recommended to strengthen the walls with longitudinal spokes tightened with nuts. Holes for screws are drilled in the side parts.

The legs are made from angles, while holes are drilled on the walls for connection to the legs using bolts. Final stage- This is the assembly of the structure.

The mobility of the device depends on the component parts of the device. High quality model a barbecue with a metal cauldron consists of the following components:

The fuel chamber contains two parts. A metal grate is installed at a certain distance from the bottom, which reduces the intensity of the fire.
compartment for dry fuel. Nice models equipped with a compartment for coals;
wheels in combination with a handle will allow you to make a mobile structure;
in some models it is mounted;
Additional attributes include a small table, a mechanical spit and a place for skewers.

Unusual barbecue ideas

A simple solution is to make barbecue using a barrel. The design can be with or without a lid. The barrel is divided into two parts. The top one is used as a cover, and the legs are welded to the bottom. Holes for ventilation must be made, and small shelves are attached to the edges. You can install a grill and skewers on them.

Grills with forging elements look great. They are equipped with additional attributes: stands, shelves or wheels. There are various types of barbecues designed by yourself:

The forged cast iron grill is original. It is decorated with any figures and patterns;

A car grill can be made from former vehicles. At the same time, you can get rid of the old body and make an unusual and luxurious fireplace for the yard;

construction from an old computer case;

product from;

decorative barbecues with images of animals or unusual designs.

Creating unusual designs depends on imagination and personal preferences.

Features of corrosion protection

The metal product must be protected from. For coloring, special compounds are used that are resistant to high temperatures. There are other processing methods. One of these methods is bluing. As a result of processing, a special film is formed on the surface of the metal, protecting the structure from heat.

The bluing procedure is performed as follows:

the surface is degreased;
individual elements are kept for an hour and a half in a solution of caustic soda, which is taken in 50 g doses. per liter of water.

Processing occurs at a temperature of 140 degrees. Stainless steel can be used instead of sheet metal. A device made from this material is resistant to weather conditions, collection and does not corrode. Such structures can last for decades.

An unusual solution for creating a barbecue are gas cylinders capacity 40 liters. They can be called suitable due to the fairly thick metal and a certain shape. Before use, they must be burned well to get rid of gas condensate. The wall thickness of a product made from reinforced forged steel should be about 4 mm, and from non-reinforced forged steel – from 6 mm.

To create a high-quality design, you must follow the following rules:

cutting must be done with precision, the tolerance can be no more than 0.5 mm;
the workpiece must be secured with clamps to the edge of the table;
The angle grinder should be larger. The larger the plane, the more accurate the cut.

When performing work, do not forget about safety. You need to wear protective clothing, protective gloves and goggles.

By following the installation rules, you can create a comfortable and beautiful barbecue with your own hands. Using quality materials the design will last for many years.

How to make a tin dustpan with your own hands, the necessary equipment for cleaning premises. Inexpensive homemade thing will bring a lot positive emotions while using it.

Consider a design consisting of only two parts:

Scoop bucket
pen

LADLE

Let's cut out the figure shown in the figure from galvanized sheet steel GOST 14918-80

The dotted line shows the places of bends, their radii, directions and angles.
Punch holes in the teeth or drill them with a drill. We bend the metal along the bend lines on the beam and beat it with a mallet (a flat wooden hammer) and get a scoop bucket.

If you make a false seam on the top edge of the scoop, from the side where the handle is attached (this will give the structure additional rigidity),

then on the scan it is necessary to add an additional sector with a length of 200 (mm) and a width equal to length seaming lines.

In the figure, the additional sector is indicated in blue.

PEN

Let's make it out of wooden block size 25x25x200 (mm). Secure the block with its sharp edge facing up. We plan the sharp edge of a wooden block. Install the block with the next sharp edge facing up. In this way we process four edges and get a regular hexagon.

how to make a tin scoop

Use sandpaper to smooth out the sharp edges where the hand is located. Let's cover it with protective decorative coating on wood.

Alternatively, you can use the handle from a blueberry harvester as a base.

Assembly order:

1. We use steel rivets to connect the edges obtained after bending.

2. We screw the handle with self-tapping screws and a press washer to the curved triangles of the hexagon.

3. Use sandpaper to smooth out the sharp edges on the metal.

Having an idea of how to make a tin scoop with your own hands, you can improvise and make a product of various shapes and sizes and for various purposes.

Advice:

For large-sized products, it is necessary to replace the false seaming with a wire one.
Do this on three sides of the ladle (on top of the ribs).
It is better to punch holes for rivets on a bent part.

Technology 5th grade

““Modeling an apron” 5th grade” - Artistic modeling. Applying the names of parts. Modeling the bib. Types of finishing. The process of creating clothes. Studying the material. Drawing of the base of the apron. Strap. Familiarize yourself with artistic design techniques. Repetition of covered material. Pocket modeling. Modeling the bottom of the apron. Fixing the material. Safety rules when working with scissors.

"Embroidery" 5th grade - Types of embroidery. Smooth surface. Five. Routing. History of embroidery. Embroidery. Physical education break. Your mood. Image. Magic chest. Get acquainted with the history of embroidery. Safety precautions. The young girl is not big, but she dresses the whole world. Counted embroidery. Safety precautions when working with an iron. Hand tools and materials.

“Natural fibers” - The finished fabric is dyed or printed with a design. Packaging in bales (pressing). The basis. Sewing materials science. In the spinning shop, threads are drawn and twisted from the roving. Carding shop. Pre-cleaning. Classification of natural fibers. How is the fabric obtained? Tape shop. Get yarn. Edge. A thin thread obtained by twisting fibers. Dividing the fiber into narrow strips (roving). Shuttle.

“Product manufacturing” - Selecting an option. Basics of design. Product.

How to make a tin scoop with your own hands

Product assembly. Manufacturing of the product. Transferring the drawing to the workpiece. Fundamentals of design and construction. Idea. Thinking over an idea. Drawing up a drawing.

“Design and modeling of an apron” - Design and modeling. Choosing fabric for an apron. Modeling methods. Modeling the main part of the apron. Pocket modeling. Modeling the bib. Measurements for constructing a drawing of an apron. Apron finishing options. Types of aprons. Purpose of the apron. Modeling an apron. Modeling.

“Natural fibers of plant origin” - Fabric taken from the loom. Cotton plant and cotton fibers. Natural fibers of plant origin. Types of weaves. Materials Science. Properties of cotton and linen fabrics. Fabric finishing. Primary processing of cotton. Sewing materials science. Linen. The process of obtaining fabric. Impact of various factors on flax and cotton. Fabric production. Textile.

There are a total of 29 presentations in the topic “Technology 5th grade”

5klass.net > Technology 5th grade > Treatment sheet metal> Slide 34

DIY scoop

Manufacturing technology for forged devices

(Blacksmith tools)

Everyone knows how necessary they are in everyday life. villager and summer residents fireplaces and stove appliances. Before we get acquainted with the technology of their manufacture, let's look at modern designs forges, using which you can count on success in your undertaking.

Rice. 1. Forge for “two lights” with a fan: 1 - umbrella; 2 — furnace nest (hearth); 3 - stand; 4 - fan; 5 - air duct; 6 - air damper; 7 — water tanks; 8 - partition.

Rice. 2. Cast tuyere (a) with replaceable grates (b): 1 - tuyere body; 2 - air damper; 3 - pipe; 4 - bottom cover; 5 - load.

In Fig. 1 shows a “two-fire” forge. Two blacksmiths can work with such a forge. The air supply to its centers is carried out by a fan with a 0.5 kW motor, and this supply is regulated by a special damper. Its design is shown in Fig. 2.

A modern lance is made of cast steel and has replaceable grates with different blowing holes. Holes located in a circle produce a wide torch flame, slotted holes produce a narrow, oblong flame. To heat small massive workpieces, a torch flame is required, and for local heating of a long workpiece, a narrow flame is required.

We can offer two designs of forges (Fig. 3) with hand and foot drives for air supply. If you can't find suitable fan, then “wind blower” 4 can be made from plywood the same way it was made in the old days.

Rice. 3. Ancient horns: a - with a “wind blower” and manual drive; b - with foot drive, 1 - box with sand and burnt earth; 2 - hearth; 3 - brick screen; 4 - “wind blower”; 5 - manual drive.

Rice. 4. Forging pliers: a - for round and square workpieces; b - for flat workpieces.

Rice. 5. Backing blacksmith tool: a - chisel; b - ironing board; c - acceleration; g - punch; d - cutting; e - cone; g - fork; z - slope.

Rice. 6. Poker (a) and its manufacturing technology (b - h).

Rice. 7. Grip (a) and forging sequence (b-d).

Rice. 8. Chapelnik (a) and forging operations (b - d).

To manufacture complex blacksmith products, you need to purchase: two types of pliers (Fig. 4); backing tool: chisel, smoother, straightener and punch (Fig. 5, a-d); as well as undercut, cone, fork and slope (Fig. 5, e-h).

Let's consider the backing tool of the first group. Work with it is carried out in a pair of “blacksmith - hammer hammer”.

Chisel in our case it is intended to cut metal. Depending on what material needs to be cut (cold or hot), the sharpening angle a is selected. For cutting hot metal, a is taken to be 15-30°, and for cold metal - 60-90°.

ironer used to level the forged surface of a product in a heated state.

Overclocking used where it is necessary to “disperse” - expand a part of the workpiece in a certain place.

Punchers, as the name suggests, punch holes. Each hole profile requires its own punch with a given bit cross-section.

The blacksmith holds a backing tool (chisel, smoother, sharpener or punch) and gives commands to the hammer: “hit”, “harder”, “quieter”.

The backing tool of the second group is installed with a shank in square hole anvil and is designed to perform various forging operations. The undercut allows you to cut workpieces by placing them on the undercut blade and hitting them from above with a hammer. The cone helps to straighten and produce ring elements. The fork is widely used in all kinds of bending operations. The slope makes it easier to forge conical elements of products.

Let's now consider technological methods forging devices for Russian stoves.

The poker (Fig. 6) consists of two elements: a forged hook and a wooden handle (handle).

We forge the hook from a round piece, dia. 20-25 mm. To keep it heated, we use special pliers. The first heating is to warm up central part workpiece and “pull back” the neck (Fig. 6, b) on the anvil. Then we heat the front part of the workpiece, stretch it onto a “rectangle” (Fig. 6, c) and, using a backing tool (straightening), we begin to forge the metal into a “wide wedge”. In this case, first we set the alignment in the center of the workpiece and make the first “punching”, then the second and third (Fig. 6, d). After the next heating, we make two more punches - the fourth and fifth. The surface took the shape of a wide wedge - a fan. Now it needs to be well leveled (Fig. 6, d) and pulled with a hammer to a thickness of 0.5-1 mm.

Then we proceed to molding the sleeve. Using the undercut and the back of the hammer (Fig. 6, e), we bend the sleeve.

Gradually tapping the bushing (Fig. 6, g), we obtain a conical surface.

Making the working part of the hook is much easier: we pull the round part of the workpiece until rectangular shape and bend the hook (Fig. 6, h). Now let's mechanically process the hook, drill a hole in the sleeve for the screw, drive in the handle - the poker is ready.

Grip(Fig. 7) has its own characteristics. Let us determine for which cast iron (by size) a grip is needed and set two sizes: the clearance between the horns Q (Fig. 7, a) and the diameter of the inner circle 0. The clearance between the horns should be slightly larger than the diameter of the bottom of the cast iron, and inner diameter grip 0 - slightly less than the maximum diameter of the cast iron shoulders. Thus, the housewife should have as many grips as there are cast iron pots of different sizes.

Now let's move on to making the grip itself. We make the sleeve in the same way as for the poker. After forging the other end into a rectangle, we cut it lengthwise using a chisel (Fig. 7, b) and bend it 90 degrees. one branch. After this, we extend the second branch onto the pyramid, make a small curl at the end (Fig. 7, c) and bend it 90 degrees. We heat the first branch, straighten it, pull it onto the pyramid and make a small curl at the end (Fig. 7, d). Then, after the next heating, using a fork, we successively form the grip horns (Fig. 7, e).

We process the grip with a file and insert the handle into the sleeve. Ready.

Frying pan or chapelnik(Fig. 8), as it was called in the old days, is also included in the set of accessories for the Russian stove.

The technology for making a chapel is initially exactly the same as for a grip. After the sleeve is made and the second end of the workpiece is pulled onto the rectangle, we begin to forge the hook.

First, bend it 90 degrees at the edge of the anvil. part of the workpiece and forge the edge of the fold, forming a spatula (Fig. 8, b). Then we form the hook itself, gradually bending it at the edge of the anvil (Fig. 8, c). The final bending of the hook must be carried out taking into account the shape of the edge of the frying pan (Fig. 8, d).

Fireplace appliances differ from stove appliances in their lightness, elegance and beauty. They perform not only their direct functions, but also serve as decoration for the fireplace room.

Poker(Fig. 9, a) can be made from rods of both round (dia. 12-14 mm) and square (10-12 mm) sections.

Let's consider the technology of making a poker from a rod of dia. 12 mm.

We stretch one end of the round piece onto the rectangle and make a small curl at its end. After that, use a fork to bend and form a handle. Similar operations are necessary to form a hook: drawing into a rectangle, forming at the end of a curl, and bending “on a fork.” To make the poker more elegant, we will make a twist in the middle of the rod. First, we stretch the central part onto the rectangle, and then, using a blacksmith’s (or metalworker’s) vice and a poker hook as a lever, we twist it (Fig. 9, b).

Rice. 9. Fireplace poker (a) and twisting operation (b).

Rice. 10. Scoop (a) and its forging (b-d).

SCOOP WITH A TWIST

Forceps (a) and the sequence of their manufacture (b-d).

Rice. 12. Options for forged handles (a), various shapes scoops (b) and methods of attaching them to the handles (c).

Scoop(Fig. 10) can be made like this. First, we forge the handle of the scoop using the same technology that was used when forging the poker. Only instead of a hook you need to forge a “leaf” and bend it to the shape of a scoop.

Let's consider the technology of forging a “leaf”. Having heated the workpiece, we pull its end to a “steep cone” (Fig. 10, b), then flatten it and get a “leaf” (Fig. 10, c). If we bend the handle to the shape of a scoop (Fig. 10, d) and rivet it to it with two rivets, then the scoop will be ready. The scoop is usually made of 0.5 mm thick sheet steel. First, it is advisable to make a pattern model from thick paper. You need to decide on the size and shape and only then make a metal scoop. Using a sharpened metal rod (scriber), we draw on metal sheet pattern of the scoop (Fig. 10, d), and then, using an anvil and metal strips, bend the scoop. First, the back part (1), then the sides (2, 3) and bend the upper part of the back wall (4) in the opposite direction.

Fireplace tongs(Fig. 11) we will forge using all our acquired experience. First, we stretch the central part of the rod onto the rectangle (Fig. 11, b) and using a fork, hammer and anvil horn we form a spring ring (Fig. 11, c). After this, we align the branches of the tongs along the length (if any branch turns out to be longer, then it must be heated and chopped off with a chisel). We will make the grips in the form of leaves (see technology above), and the places for holding by hand - by twisting (Fig. 11, d). These places must first be stretched onto a rectangle.

After making all the devices, they must be thoroughly straightened and blued. It will give the products a finished look and protect them from rust. The products are uniformly heated to a temperature of 300-500 °C and lowered into a tank with waste machine oil. If the bluing did not work out as expected the first time, it should be repeated. After this, the products are wiped well with a rag. Options for manufacturing forged handles are shown in Fig. 12.

DIY folding grill

A folding barbecue, made with your own hands, is convenient during transportation and does not take up much space in the car. For lovers of barbecue in nature, this design is intended, which can easily be made independently.

The design consists of four components:

Bottom (3)
side walls lengthwise (2)
side walls width (1)
legs (4)

Folding grill made of angle and sheet metal three millimeters thick. With such a thickness of metal, the impact high temperatures it does not deform. The best option, if all structural parts are made from of stainless steel– we will get an “eternal” use option.

Consists of two parts:

The circuit is welded from metal corner GOST 8509-93
the plate is welded to the contour

The size of the structure can be any, it all depends on your appetite and the amount of meat cooked at one time.

SIDE WALLS

Let's drill through holes for better combustion of coals and cut grooves for fixing the skewers at the desired angles.

By lenght

Width

To make grooves, we weld pieces of metal on both sides of the sheet.

LEGS

We will make it from metal rod GOST 2590-88, Ø12…14 (mm).

Assembly order

1. Let's bend the development of the long wall on both sides. In order for both parts to turn out identical, two sheets of blanks must be inserted into the bending machine.

2. Let's measure the distance between the two bent planes.
3. Cut the long corners to the resulting size. The corner should fit tightly into the cavity between the bent sides.
4. Let's weld the bottom.
5. Let's drill through technological holes:
– 4 for pins Ø6 (mm);
– 4 threaded M 10
6. Let's cut the thread
7. Place the side wall against the bottom and insert the pins. The wall should open to an angle from 0° to 90° (the plane of the corner will fix the angular movement of the wall at an angle >90°).

8. Let's weld the pin with inside bottom.

9. Screw the legs into the threads.
10. The side walls are the width, insert them through the grooves.

DIY scoop made of tin

A folding barbecue, made with your own hands, is ready for use.

This model will be easily disassembled and assembled within one minute, and the dirtiest surface will remain inside. We place the disassembled parts inside the grill.

As you can see, when assembled it is a small suitcase. If you want to carry it in a vertical position, you need to install a simple lock on the folding walls and attach a handle to one of them.