Not only depends on the condition of the façade appearance apartment building and the company office. When the protective layer is destroyed and cracks form, moisture begins to seep into the structure. Black spots of fungus appear in the corners. Heating requires more energy. The noise from the street is louder. Repairing the facade brings comfort back to the apartment and office. The building takes on an attractive appearance. The protective finishing layer has been restored, and the life of the house will be extended for several years.

Repair of house facade

Timely repair and finishing of the facade prolongs the life of the building and creates comfort in the home

Cosmetic repairs of facades must be carried out regularly, approximately every five years. In this case, only the finishing of the house is replaced, small thin cracks are repaired. The walls are covered with decorative and at the same time protective cladding. Regular preventative work will help to avoid in the near future the large costs of reconstructing the building frame during a major overhaul.
When water gets into a small crack, it expands when it freezes, destroying the material. The next drop will penetrate deeper. The wind blows away particles of finishing and bonding material. A broken drain does not drain water and wets the foundation, causing part of the foundation to sag. The house begins to get damp, cool down and fall apart more and more. In this case, only major repairs can restore the building.

Gutter replacement

Repairs to the facades of buildings and apartment buildings in the city are carried out by special teams equipped with lifts or climbing equipment. A private house you can put it in order with your own hands.

The sequence of work is the same:

1. Inspection of the entire facade, determining the degree of destruction and the scope of future repairs.
2. Cleaning all cracks, moisture stains, salt protrusions and places where the finish is crumbling.
3. Elimination of causes of wetting and salt formation, treatment of cleaned areas.
4. Cleaning from dirt, dust, applying a primer or protective composition to the walls.
5. Facade finishing.

If large cracks are detected, major repairs are necessary.

Crack on the facade

Cosmetic repair of a plastered facade

Brickwork and plaster suffer more than other types of finishing from destruction by rain and frost. Such buildings require regular façade repairs. These are mainly apartment buildings built in the second half of the last century.
I am constantly doing renovation work. I start by cleaning the plaster from dirt. At the same time, I tap the entire surface in search of hidden voids. These may include cracks and peeling finishes. The penetration of salt is noticeable immediately; it stands out as whitish spots. I carefully repair all defects. In places where moisture and salt accumulate, I examine the walls inside. Perhaps pores have formed on old pipes or dew accumulates due to damaged thermal insulation.

Plastering the facade

I continue after troubleshooting:

• I clean out all voids and peelings;
• I select salt plants to their full depth and treat the places where they form with a special compound;
• I first seal cracks and deep dents and apply reinforced mesh fiberglass;
• I cover the wall with a layer of plaster, embed the mesh in it vertically with an overlap;
• I install a profile in the corners to strengthen them;
• I apply a finishing coat;
• After drying, I cover it with decorative acrylic putty or paint.

Walls finished with plaster and tiles are less susceptible to damage. The seams absorb moisture and fall out. It is necessary to check and tap each one at the beginning of the repair.

Wall insulation work

Brick absorbs moisture and does not store heat well, especially silicate brick. Repairing the facade of an apartment building often includes insulation. For the correct choice of materials and type of installation, it is necessary to make a project for the reconstruction of the facade and technical specifications for the builders. This is what architects do. The work procedure remains the same, only after processing and leveling the walls is the insulation installed on the façade.

Facade insulation wooden house expanded polystyrene

For a tight fit of thermal panels, a flat surface is needed. All cracks and potholes are sealed. Then the flatness is examined using a ruler. Deviation up to 2 mm. The vertical position of the wall is checked using an angular level. When tilted, water will drain and icicles will form. To improve adhesion, the facade is coated with a primer.
The boards are glued to the wall surface special glue. It is bought ready-made in the store. It is selected based on the materials that will be glued. The insulation made of basalt and stone wool is additionally fixed with umbrella dowels. Mineral wool is placed between wooden planks and covered with fiber or film. Waterproofing is being done. Moisture removed from the wall to the outside will flow down it. Then plaster with mesh for strength and finishing. Facade repairs should be carried out in dry weather, preferably in summer.

Wall insulation work

Inspection and major repairs of the building structure

A signal for urgent major repairs is the formation of cracks from the foundation to the roof and horizontal cracks in the areas of floors between floors. This means that the house is shrinking and warping. Repair of the facade of a house should begin with a detailed examination, which must be performed in one of the specialized companies licensed to carry out this work. The causes of cracks are eliminated before façade work begins.
Basically, the distortion of the house structure causes soil subsidence on small area. It can be provoked groundwater, broken drain, violation of foundation waterproofing, simple negligence and water leakage from the water supply or sewerage system. An inspection of an apartment building is carried out not only from the outside, but also from the inside.

House in need of major renovation

A technical specification is being drawn up to eliminate the causes that caused the destruction of the house and carry out major repairs. The foundation is being strengthened and the gutters are being repaired. After this, the cracks are cut out and covered. The use of a mesh is mandatory. All work must be done by specialized organizations for the project of reconstruction and repair of the facade.

Attention! In big cities, historical places and for ancient buildings it is necessary to issue a color passport for the facade. You cannot change the color and decor without permission.

Major home renovation

Wet and ventilated façade

Insulated facades are inspected and a list of defects is compiled. This could be corrosion of the metal profile, destruction of insulation or siding panels due to moisture. Rodents love foam plastic. Mineral wool rots when exposed to moisture. Then all damaged materials are removed and defects are cleaned. The insulation is being replaced and new cladding is being done.
Finishing slabs protect external walls well from wind, rain and protect from frost. Therefore, it is enough for insulated facades to carry out cosmetic repairs every five years. It is advisable to coat cladding made of natural and artificial stone with a protective compound every three years. Apply to the seams between clinker and porcelain tiles waterproofing coating. Then the facade will need major repairs in 50 years or later.

Waterproofing coating on the seams between tiles

Do-it-yourself façade repair of a private house

The advantage of a private house is its low height. For repair work no special lifting equipment required. It is enough to make scaffolding or install sliding staircase. Caring for the integrity of the home. It is necessary to regularly inspect the house from the outside and inside for the formation of cracks, stains of dampness and salt.
Insulation and finishing should be done immediately after completion of the installation of walls and roof. Then the house will last a long time and will be cozy. The repair procedure is the same as for an apartment building. The facade is cleaned, the surface is leveled and finally decorative finishing. All work is carried out at above-zero temperatures.

Repair work has been completed

Before finishing the building, it is necessary to make calculations for the vapor permeability of the materials. It should increase from the inside of the wall to the outside. Then the moisture that gets into the masonry will be discharged outside. Load bearing capacity the foundation must be sufficient to support the additional weight of the insulation and cladding. When in doubt, use lightweight materials: foam, mineral wool, acrylic and vinyl siding on a wooden beam.

Timely repair of the cottage facade helps prevent the process of destruction external walls building, improve thermal insulation characteristics and give it aesthetic appeal. But, achieving such a result on your own is very difficult, since to perform high-quality repair work you need to have special knowledge and skills.

Major and cosmetic repairs

Taking into account the nature and area of ​​damage to the walls, there are two types of repairs to the facade of a private house:

• cosmetic. Performed when minor cracks appear and includes restoration upper layers or areas of facade finishing, without interfering with the structure and texture of the external walls of the building;
• capital. Designed to restore damage, the total area of ​​which is at least 30% of the entire facade. In addition to caulking and sealing seams, during major repairs waterproofing of walls, replacement of windows, etc. can be carried out.

Regular cosmetic repairs will avoid increasing the area of ​​damage to the walls and delay the need for major repairs.

The cost of repairing the facade of a private house

Type of work	Unit change	Price
Primer (if uneven walls)	m2	80 rub.
Facade plaster	m2	400 rub.
Laying facing tiles	m2	1100 rub.
Tiling slopes	m.p.	280 rub.
Tiling arches	m.p.	330 rub.
Installation of flashings, parapet covers	m.p.	250 rub.
Laying the border	m.p.	250 rub.
Grouting joints	m2	250 rub.
Epoxy grout	m2	830 rub.
Additional work
Preparing the area for work (cleaning, preparing a site for storing material)	-	500 rub.
Removing electrical wiring to a temporary support	-	1500 rub.
Installation of metal scaffolding	m2	85 rub.
Manufacturing and installation wooden scaffolding	m2	220 rub.
Installation support platforms	m2	230 rub.
Transferring drainage system pipes to scaffolding	m.p.	180 rub.
Installation of protective construction film on windows, doors, roofing and decorative elements	m2	80 rub.
Cleaning walls from dirt and dust	m2	65 rub.
Roof overhang lining	m.p.	680 rub.
Installation lighting fixtures	PC	700 rub.

How is the façade repaired?

Repair work on the facade of a private house includes 3 main stages:

• Preparatory. At this stage, the old facade finishing is removed and the surface of the walls is cleaned.
• Restorative. Includes work on leveling walls and sealing cracks. First, the cracks are widened and cleaned of dust, after which they begin priming. work surface facade. If necessary, the walls are plastered.
• Finishing, where the façade is faced with finishing materials. The most affordable option is painting the walls. The most expensive options include tiling or stone finishing.

At the customer's request, ebbs and gutters located on the walls can be repaired country house, as well as during the repair carried out additional work for facade insulation, replacement of cornices.

Company offer

Want to high-quality repairs facade of a private house in Moscow in a short time and at an affordable price? Then contact the specialists of the Alfacom company. We will complete work of any complexity quickly and with guaranteed impeccable quality. Our company is ready to provide both cosmetic and major repairs to the facades of cottages of various heights using only modern, safe materials and technologies.

The StroyProekt company will carry out façade repairs in Moscow and the Moscow region. We work with objects of any level of complexity and degree of damage. Our craftsmen pay special attention to the quality of the materials used. The work is carried out in strict accordance with current technologies. This guarantees long-lasting results.

What tasks does facade repair perform?

1. decorative function;
2. protection load-bearing structures from negative factors environment;
3. heat and waterproofing.

Over time, under the influence of dust, moisture, temperature changes and aggressive substances (for example, contained in exhaust gases), the coating becomes unusable. Timely repair of the facade will help restore the integrity of the protective materials and return the building to its aesthetic appearance. These works must be carried out at certain intervals. It is determined by the characteristics of the environment, the nature of the materials and technologies used.

If you ignore the repair of the building facade, the rate of wear of the load-bearing structures will increase. The service life of the structure will be noticeably reduced. The costs of maintaining it will be very high with no guarantee of a positive result. Regardless of the level of reliability, facade materials it is necessary to periodically check and carry out repairs (cosmetic or major).

Damaged cladding poses a threat to human life. Falling tiles, plaster and other materials can cause injury. Therefore, the facade must be carefully taken care of.

Major renovation of the facade

Major repairs to the façade of a house involve filling and waterproofing all cracks, seams and other damage to the load-bearing surface.

Priming provides sufficient adhesion to fix the plaster materials, after application of which the cladding is installed.

Major repairs of the facade are chosen based on the degree of damage. If there are minor defects that do not affect the functional characteristics of the cladding, it is sufficient to restore its integrity.

For the final external covering, tiles, natural and artificial stone are used, decorative brick, porcelain tiles, siding. When restoring historical buildings, materials are chosen that are as close as possible to the original ones.

The renovation of facades in Moscow is completed by applying hydrophobic coatings. This provides additional protection from moisture and aggressive substances, and also extends service life.

Upon completion of the work, the building receives an aesthetic appearance and properly functioning external elements. A wide range of products and materials will guarantee impeccable quality in the implementation of assigned tasks.

• scope of work;
• urgency;
• degree of damage;
• the nature of the materials used;
• building features (for example, the need for industrial climbers).

In our company, the cost of facade repair is determined individually for each client. We evaluate the project. Based on the information received, the most suitable technologies repair. Our craftsmen will restore and modernize the previous protective coatings.

Cosmetic repair of the facade

The most common goal of facade repair is to restore the aesthetic appearance of the structure while maintaining the functional parameters of the cladding. To achieve this task, cosmetic repairs of the facade are periodically carried out. The cost of this procedure is more affordable than a major restoration.

Facade repairs are carried out to improve functional characteristics cladding:

• increased moisture protection;
• ventilation device;
• additional thermal insulation.

Changing the appearance of a building is one of the most significant tasks repair work. Restoration of historical objects, including facades, is carried out with appropriate permits from specialized government organizations.

Cosmetic renovation of building facades in Moscow and the Moscow region extends the period safe operation structures. Load-bearing elements are reliably protected from moisture, temperature changes, fungus and mold, which can reduce the comfort of staying inside.

We work with any facades. Our goal is to restore or update their appearance, as well as improve their protective characteristics. Plaster coatings and tile cladding are most susceptible to wear. They slowly deform and collapse under the influence of moisture and temperature changes. Immediate repair of the building's facade will help to temporarily stop this process. Our specialists will select materials that ensure a long service life of the coating.

Ventilated solutions require less façade repair. Clever multi-layer construction provides effective removal moisture, as well as protection from low and high temperatures. Maximum reliability and durability are ensured subject to the correct implementation of ventilated facade technologies. This kind of work requires high precision and control. If the owner of the property decides to save money in favor of low-quality materials, the facade of the house will soon need to be repaired, possibly a major one.

We can offer our clients other types of facades

The facade is the external appearance, the face of any building. Forming the architectural environment and historical flavor of the city, the facade is the part of the structure that is most susceptible to the destructive effects of climatic and weather conditions. Rain, wind, snow, sudden temperature changes inevitably leave marks on the walls of the building.

In addition to the aesthetic component, the technical condition of the facade determines temperature regime inside the building. The costs of any most unfavorable climatic conditions are minimized by high-quality execution of façade measures.

Facade finishing is a complex of specific construction services performed by facade company. These include examination of defects and technical condition construction, cleaning, repair operations. Timely and professional cladding will preserve the attractive image of any building for a long time.

Installation of ventilated facades using curtain panels or siding is one of the most common methods of insulation. Insulation, which uses mineral or basalt wool(less often - polyurethane foam or polystyrene foam) are installed under the panels.

The layers of the ventilation facade look like this: bearing wall, insulation, air space and protective layer, that is, facing. This arrangement of layers in the structure as their thermal conductivity decreases is the most optimal. Vapor permeability resistance increases from the outer to the inner layer. Ventilated façade is fundamentally different from other methods due to air gap, which removes atmospheric and concentrated indoor moisture. It acts as a buffer in which the air temperature is higher than with outside walls Such work can be carried out at any time of the year, and no preliminary leveling of the walls themselves is required. According to experts, depending on the materials used, the first repair may be required no earlier than 25 or even 50 years.

Facade construction with siding is carried out using lathing. Here they use bars measuring at least 40x40 cm or a galvanized profile 50-80 cm. When calculating the size of the sheathing, the thickness of the insulation is taken into account, as well as a 20 mm gap for air ventilation. The pitch of the sheathing is chosen so that the insulation is laid with a slight compaction without trimming. When purchasing material for insulation, keep in mind that its total area should exceed the total area of ​​the facade by approximately 5%. The waterproofing is attached with an overlap of 10 cm in the direction from bottom to top. Siding is a fairly durable material that is also resistant to temperature changes and precipitation.

In addition to vinyl and steel siding, block house, facing brick, porcelain tile, etc. are also used for cladding a house.

One of the popular facing materials steel three-layer sandwich panels. Here the top and bottom layers are rigid aluminum sheets, and the intermediate layer is polyethylene. All parts are fastened together by hot pressing. Sandwich panels can have either a smooth or corrugated surface. This material is quite lightweight, so it is recommended for use where it is undesirable to increase the load on the foundation.

The so-called “wet” facade is another method of insulation. It begins with insulation being placed on top of the glue, followed by a reinforcing layer, and structural plaster is laid on top. In order for wet installation to hold as firmly as possible, it is also necessary to use a primer. It improves adhesion to the polymer-cement adhesive base and strengthens the wall surface. You will also need a base profile that serves as a support for the insulation and ebb. To protect against accidental damage to corners, special perforated corners. The thickness of the insulation itself is selected individually and is 20-150 mm. Installation starts from the corner. The insulation board is coated with a thick layer of glue along the edges, and it is applied pointwise in the middle. After drying, additional fastening is carried out using dowels - umbrellas. Their number is calculated to be approximately 6-7 per 1 m2 of wall. Facade fiberglass mesh with a density of 140-160g/m2 is used as a reinforcing material. Apply along the grid decorative plaster. If necessary, the plaster is painted in at least two layers.

Types of facades

Regardless of which method of constructing the facade is chosen, sooner or later it will require one or more types of work. These include:

• Sealing seams is a set of measures aimed primarily at quickly insulating the facade and extending it performance characteristics without the need complete renovation. For this purpose, the interpanel joints are finished, gaps and cracks are eliminated.
• Restoration is a concept that implies prevention, renewal and preservation of the external appearance of a building. Such facade finishing is considered quite voluminous and labor-intensive. Restoration work on the facade requires a highly professional approach, especially when it comes to buildings of historical and cultural significance.
• Hydrophobization is one of the most pressing tasks, since it helps protect the facade from various damage associated with exposure to precipitation and temperature changes. During such work, the outside walls of the building are treated with a special protective solution that prevents salt from escaping.
• Washing is a process that façade builders perform most often; embassy washing will allow you to update the appearance of a building in the shortest possible time. However, such work is considered quite dangerous, since it is often carried out at heights. In this regard, they must be trusted experienced specialists, who will not only strictly adhere to the necessary safety measures, but will also quickly identify suitable cleaning and detergent products.
• Repair and finishing works, implying a wide range of measures - from improving individual elements of the building to overhauling the entire structure.

In addition to its main purpose, most of the types of work mentioned can also be aimed at solving problems in the field of energy saving. They are successfully used here modern technologies and building materials.

Features of the event

Today there is a wide variety of facing materials to suit every taste and budget. Almost all of them have good performance characteristics.

However, in terms of installation, there are still some features and differences that are worth paying attention to. Arrangement of facades from:

• Metal cassettes are made based on design features this material. There are metal cassettes of open and closed type.

In the first case, fastening occurs by step-by-step installation material on vertical racks frame. Here you need to pay attention to the fact that the side shelves of the next panels overlap the previous ones. According to standards, the depth of entry should be no more than 2.5 cm, and the installation step of fasteners should be 20-25 cm. Since when installing panels open type Since all their fastening points are in plain sight, it is recommended to select fasteners of the same color as the cladding material itself.

Closed-type installation is carried out by screwing screws on the upper part of the panel to the sheathing, and its lower edge is secured to the panel located in the bottom row. Only very thin cassettes are suitable for such work; the place of their fixation is hidden.

The facade, made of metal cassettes, has a rather attractive futuristic appearance, and it is also considered quite durable.

• Porcelain tiles are produced in several stages, the first of which is preparatory work, consisting in marking and fencing the territory, ensuring a convenient location and accessibility of materials and equipment used during installation. Next stage– marking. The installation locations of load-bearing and support brackets and the fastening of profiles are indicated. This is followed by the installation of brackets. To do this, you need to drill the corresponding holes in the wall with a hammer drill, install a paronite gasket, and then install the supporting brackets using dowels and a screwdriver. Next, thermal insulation and protection from wind and water are installed. Insulation boards are installed in a checkerboard pattern from bottom to top. Upon completion, holes are drilled through the wind-waterproof film and insulation boards for disc-shaped dowels. The fifth stage is the installation of vertical guide profiles and fire shutoffs. To minimize deformations due to temperature changes between adjacent profiles, it is recommended to leave a gap of 8-10 mm wide. The last stage is the cladding with porcelain stoneware slabs.

The facade made of porcelain stoneware is characterized by a high degree of fire safety, frost resistance and is able to maintain its original appearance for a long time, despite the vagaries of the weather.

• Fiber cement panels, which are based on ventilated-type hinged facades. This design consists of a frame and cladding, which are installed on the outside of the building. At the first stage, brackets are installed, which are screwed to the wall using dowels or anchors.

Next, a layer of thermal insulation is laid ( mineral wool or thermal insulation board), the thickness of which should be 10-15 mm. After which you can begin installing the system of profiles and guides. The main vertical profiles are laid out in the shape of the letter P, and the additional ones - in Z- and L-shaped zigzags.

The final stage is the installation of fiber cement panels. As a result of such work, a small gap is formed between the frame and the cladding, allowing air masses to move freely.

Such a facade not only looks stylish and modern, provides an acceptable temperature regime indoors, but is also very
effectively protects the building from the damaging effects of the environment.

• A natural stone requires careful and attentive preparation. This is due to the fact that such finishing material must be laid out only on clean and flat surface no chips, depressions, oil stains or paint. Before finishing the wall, the stone should first be laid on the ground to form a pattern. Then glue is applied to it or cement mortar. After this, the material is pressed against the wall. The final stage is jointing, which involves filling the space between the stones.

In order for the stone facade to acquire a more beautiful appearance and also be protected from the negative effects of precipitation, after the solution has dried, it must be treated with a water-repellent liquid.

• Clinker tiles begins with preparing the base. Surfaces are leveled using plaster and putty, impregnated with primer and primer. The clinker is glued only to a completely dry base, so you need to wait for it to dry and not carry out work during even light rain. Marking must be carried out - starting from the top of the window slopes, horizontal stripes(it is necessary to make a small 3-5 mm overlap for a high-quality finish upper slope). Next, a solution is prepared from a special adhesive composition, which is applied to the wall with a notched trowel. After this, the tiles are laid, on the inside of which the prepared mortar is also applied using a regular spatula. The recommended joint width is from 10 mm to 14 mm. For ease of installation and finishing, some manufacturers produce special corner tiles; otherwise, the edges of the cladding are trimmed using a grinder or an electric tile cutter. The final stage is unstitching.

The facade made of clinker tiles has an attractive appearance, is durable, resistant to mechanical damage, exposure to ultraviolet radiation and temperature changes.

• Aluminum cassettes performed in two ways - with hidden and open fastening. The second is simple and fast. The elements that make up the structure already have holes for installing self-tapping screws. Aluminum cassettes are fixed on a metal profile. Such façade structures allow easy replacement of any part.

Method with hidden fastening allows you to obtain an almost perfectly flat surface, but is characterized by higher complexity. Such facade cassettes there is only one bent side (cassettes for mounting with visible fastening have two), which has a special edge that allows you to fasten the upper and lower cassettes together. Otherwise, the installation sequence is almost identical: first, the lathing is installed from a special cellular profile, then thermal insulation (special slabs or ordinary mineral wool) is laid in the cells, then wind and water protection is installed. All layers are secured with dowels. Afterwards, the profile is mounted into which the aluminum cassettes are installed.

This type facade does not overload the walls, is resistant to various negative impacts and hides all the shortcomings of the main walls, making the building much more beautiful.

Dowels are first installed in the drilled and dust-free holes, and then the brackets are screwed in. Next, insulation boards with slots made in them at the places of the brackets, as well as a waterproofing membrane, are installed. The resulting composition is fixed using disc-shaped dowels. Now you can install the guide profile, and on it - the hooks to which the cladding will be attached. It should be noted that the width of the gaps between the panels should not exceed 12 mm.

The resulting facade has a spectacular, extraordinary appearance, and the walls are protected from temperature changes, moisture and other destructive influences.

• Plaster facade differs in that in this case special building mixtures are used, which require dilution with water. The technology for installing such a facade is quite simple. First it is applied to the wall glue mixture, to which slabs of synthetic or mineral origin are attached. Following them comes additional mechanical fastening in the form of “mushroom” dowels.

The last stage of such work is decorative plaster finishing.

Distinctive feature The “wet” facade is that it allows you to solve two important problems - to insulate the walls and achieve a beautiful architectural design of the building.

• Repair of facades involves carrying out work at heights using special equipment and building materials. It can be divided into three types: cosmetic repairs, which are carried out in a short time with minor damage to the external cladding (plaster or paint); major renovation of the façade of the building, involving a significant amount of work and large quantity time costs; partial renovation facade - this is the restoration of a separate part of the building.

Making a choice in favor of one material or another for facade finishing, in any case, you should rely on your own taste and the opinion of professionals.

Prices per m2

The cost of facades mainly depends on their type. In addition, it is necessary to take into account the material, as well as additional issues that the construction organization will undertake. This includes dismantling the old cladding, applying a primer, removing efflorescence, etc.

Today, the average cost of major activities is as follows:

However, it is worth remembering that the cost of materials only increases from year to year. Following them, prices for façade installations are rising. Therefore, the sooner you start decorating the facade of your house, the sooner it will begin to bear its positive fruits in the form of a beautiful external appearance of the building and an increase in its thermal insulation properties.

№	Title of work (without materials)	Unit	Price, ₽
	Wall insulation
1.	Installation of the first layer of insulation	m 2	80
2.	Installation of the second layer of insulation	m 2	80
3.	Installation of insulation fungi (1st and 2nd layer)	m 2	90
4.	Installation of insulation on slopes	m.p.	50
5.	Membrane installation	m 2	60
6.	Installation/dismantling of scaffolding	m 2	95
7.	Installation + relocation of the lift	m 2	150
	Subsystem installation
8.	Marking of brackets	m 2	150
9.	Fastening brackets (anchors)	m 2	20
10.	Installation of T-profile	m 2	350
11.	Z-profile installation	m 2	325
12.	Installation of L-profile	m 2	290
13.	P-profile installation	m 2	270
14.	Installation/dismantling of scaffolding	m 2	95
15.	Installation + relocation of the lift	m 2	150
	Installation of slopes
16.	Fire cut-off installation	m.p.	100
17.	Installation of the starting profile to the window	m.p.	55
18.	Slope trimming	m.p.	70
19.	Installation of a slope on a subsystem	m.p.	75
	Installation of cladding
20.	Metal cassettes	m 2	455
21.	Porcelain tiles	m 2	560
22.	Fiber cement boards	m 2	690
23.	Composite	m 2	510
24.	HPL panel	m 2	700
25.	KMU panel	m 2	640
26.	Metal siding	m 2	350
27.	Linear panels	m 2	390
28.	Clinker tiles	m 2	1600
29.	A natural stone	m 2	2400
	Wet facades
30.	Preparing the walls	m 2	90
31.	Installation of the starting profile	m.p	52
32.	Installation of insulation (with glue)	m 2	75
33.	Plaster base layer	m 2	230
34.	Installation of slope angles	m.p.	49
35.	Finishing putty	m 2	270
36.	Slope putty	m.p.	160
37.	Primer(3 layers)	m 2	75
38.	Painting(2 layers)	m 2	80
39.	Installation of decor on windows	m 2	470
	Facade restoration
40.	Sealing seams	m.p.	270
41.	Removing old putty	m 2	140
42.	Facade cleaning	m 2	23
43.	Gluing reinforcing mesh	m 2	260
44.	Facade plaster (3 layers)	m 2	380
45.	Primer (3 times)	m 2	70
46.	Painting	m 2	80
	Mobilization of the construction site
47.	Change houses 3x6m. (rent)	1 month	9 000
48.	Garbage container	1 month	6 000
49.	Biotoalet (1 piece)	1 month	4 000
50.	Security (1 post)	1 month	45 000
	Working documentation
51.	Geodesy	m 2	55
52.	Design	m 2	100
53.	PPR	m 2	25 000
54.	KMD	m 2	25 000
55.	Anchor testing	m 2	20
56.	Feeding fungi	m 2	20