Many lovers homemade equipment are engaged in the development and production of all-terrain vehicles on caterpillar tracks.

The most different solutions when bringing ideas to life, but the biggest problem for enthusiasts of this type of transport was and remains the tracks. Of course, no one forbids using factory-made movers in your samples, but you would like an all-terrain vehicle (or snowmobile) made by yourself to have homemade tracks. Let's look at some methods for making tracks that have shown fairly good performance.

The simplest option

A caterpillar propulsion system for snowmobiles and light all-terrain vehicles can be made on the basis of an ordinary bushing-roller chain and conveyor belt. To make such a caterpillar, there is no need to have special tools or equipment; everything is done “on the knee”.

Transport tape caterpillar

To extend the service life of the tape, it is advisable to sew its edges with fishing line in increments of about a centimeter (just as seamstresses do overcasting the edges of fabric), this will protect the tape from fraying. The connection of the tape into a ring can be done in any way in an accessible way, for example, use a hinge like a piano loop, or sew the ends of the tape (less reliable way).

The thickness of the tape should be selected based on engine power. When using motorcycle engines domestic production, good results shows a tape with a thickness of 8 - 10 millimeters, which is used on agricultural conveyors.

Despite the ease of manufacture, such a homemade snowmobile track has a decent service life and is also easy to repair if necessary.

Tire tracks

It is quite common among DIYers to make tracks from car tires. For this purpose, tires from trucks are selected, preferably with a suitable tread pattern (there will be less work with the bus in the future).

Tire caterpillar

To make such a caterpillar, it is necessary to cut out the sides from the tire, leaving only treadmill. This work is quite labor-intensive and requires a lot of patience, since the only tools used are a well-sharpened shoe knife.

To simplify the work, you can wet the blade in a soapy solution from time to time, then the rubber will be cut easier. Alternatively, one could consider using homemade devices for cutting, or use a jigsaw on which a file with a fine tooth is attached (it is also better to moisten the file with soapy water).

First, the beads are cut off from the tire, then, if necessary, excess layers are removed from the underside of the resulting ring (if the track is too hard). After this, if the tread pattern does not satisfy the designer’s requirements, a new lug structure is cut.

A homemade caterpillar made from a tire has an undoubted advantage over the model described above, since it has an initially closed circuit, which means its reliability will be many times higher. The downside is the limited width of the finished track, but if necessary, you can use a double and triple-width option.

Belt tracks

An attractive option because of its relative simplicity is to make a caterpillar with your own hands.

Belts with a wedge-shaped profile are connected into a single unit using lugs attached to the belts using rivets or screws.

Thus, you get a caterpillar track with already existing holes for the drive sprocket (for this you only need to leave gaps between the belts).

There are many ways to make caterpillars - the main thing is to have desire and patience, and then everything will work out.

A DIY caterpillar can be made by any craftsman. If you have been thinking about how to make a caterpillar for a long time, then you should read the recommendations presented. To carry out the work, you can use a variety of tools and materials. It is, of course, permissible, if necessary, to use a caterpillar that was produced in a factory. But it will cost much more than if you do the manufacturing yourself. The article will present several options for making tracks, one of which you can choose for yourself.

A simple option for making a caterpillar

A do-it-yourself caterpillar can be made using the simplest technology. This will take you a minimum amount of time. The caterpillar mover can be made on the basis of a bushing-roller chain, as well as a conveyor belt. To carry out the work you need to prepare a certain set of special tools or equipment. In order to extend the life of the tape, it is recommended to sew its edges with a fishing line, strengthening it at a distance of 1 cm. It is necessary to use the principle that seamstresses use to overcast the edges of fabric, which will protect the tape from damage.

A caterpillar can be made with your own hands by connecting elements into a single ring; this can be done in several ways. So, it is permissible to use a hinge like a piano hinge; you can also use a less reliable method, which involves sewing on the ends of the tape. It is important to note that the thickness of the tape must be selected, which corresponds to the power of the motor. If you intend to use an engine from a domestically produced motorcycle, then you can use a tape whose thickness is 10 mm, similar to that used on agricultural conveyors.

If you make your own caterpillar using this technology, you won’t have to spend a lot of effort. Despite the fact that this model of caterpillar is quite simple to make, it has a long service life and a long service life.

Making caterpillars from car tires

You can make your own caterpillar using car tires. To carry out the work, it is necessary to select tires borrowed from trucks; it is recommended to use suitable drawing tread, while you will spend less effort when working with the tire. The manufacture of such a caterpillar must be done by cutting out the sides from the tire, while leaving space for a treadmill. It is worth considering that this work is quite labor-intensive and requires the application large quantity patience and strength, you must use only a well-sharpened shoe knife.

In order to spend less effort when making a caterpillar for a car with your own hands, you can wet the blade from time to time using a soap solution. As alternative solution You can use a device designed for cutting; it is also possible to use an electric jigsaw. A file with small teeth must first be attached to the latter; the file must also be pre-moistened with water; such manipulations must be carried out periodically during the work process.

Work technology

Do-it-yourself tracks for a car must be made using a technology that involves the initial removal of the tire beads, then, if necessary, you need to remove the excess layers that are located on the wrong side of the formed ring; this is necessary if the track has increased hardness. If the tread pattern is not suitable, then you need to cut a new structure, which will be necessary so that the structure can cling to the soil.

A snowmobile track made with your own hands according to the scheme described above will have many advantages, even if compared with the option described above. This is due to the fact that it has a closed loop, which indicates reliability. But there are also disadvantages, one of which is expressed in the limited width of the track, but if there is a need, then a double width can be used.

Making a caterpillar from belts

Next option caterpillars are especially attractive because you don’t have to waste extra effort during the work. Before you begin, you need to prepare belts that have a wedge-shaped profile. They have to be connected into one whole using soil hooks that are fixed with screws; rivets can be used as an alternative solution. The result is a snowmobile track, created with your own hands, which has holes intended for the drive sprocket. In order to create the holes, you will need to leave some space between the straps.

Another option for making a caterpillar

Before you make a caterpillar with your own hands, you need to choose a technology for carrying out the work. It is also possible to use the method presented below. The propulsion frame can be welded using pipes that have rectangular section. It is recommended to connect them using a frame, this will make the structure collapsible. The splined part can be borrowed from Buran, this will allow drive shafts, you need to weld the splined part of the shafts, which are borrowed from Oka, to them. It will also be necessary to use brake discs. When working on the front shafts, you need to install brake mechanisms on them. Some part of the gearbox housing needs to be cut off. Making a caterpillar with your own hands will allow you not only to save money, but also to move through snowy areas without any problems. This design can be used for a long time without the need for repairs.

(ArticleToC: enabled=yes)

This cheerful caterpillar made from a tire with your own hands will decorate not only the playground, but also garden plot. After all, every owner of a house or cottage wants to make his piece of land cozy and different from others.

Those who have unlimited finances resort to the help of landscape designers who build decorative pond, alpine coaster, fountains and other exterior elements.

But no less beautiful things can be created with your own hands, using, it would seem, waste materials – plastic bottles And car tires. Craftsmen easily turn them into wonderful garden furniture and delightful flower beds, swimming pools and fairy-tale characters, elephants, giraffes, frogs, etc.

All you need to make a tire craft is patience, a sharp knife, brushes and paints.

The tires selected for the job must be clean and dry to prevent the paint from peeling.

Making a caterpillar that kids love and makes adults smile is very easy. First, the tires are painted in bright colors, and when they dry, they dig into the ground using one of the proposed options given below.

Flirty caterpillar in a Panama hat

Scared caterpillar with cute spring horns

Tires can be dug in at the same level or at different levels, i.e. the first and all odd ones - to a shallower depth, the second and even ones - deeper.

Face design

There are also several options for this:

• it can be drawn on plywood, giving it a funny shape and attaching it to the front of the first tire;
• secured on both sides to the side holes of the first tire using self-tapping screws;
• create using for eyes plastic lids or wheels from a children's car.

Making antennae

Springs and wire, plastic pipes and bottles are suitable for antennae. You can decorate the craft by attaching a flower to your head.

Coloring

As a rule, the caterpillar is painted green and green-yellow. The antennae are made yellow, and the eye color is made according to desire or available material.

The process of creating crafts from tires is much simpler and cheaper than from metal or wood, and their service life is many times longer. The products are bright and exclusive. And to create it, neither material costs nor special professionalism are required.

• It is recommended to dig in the tires close to each other so that if the child slides off, he cannot get hurt or get stuck between them;
• There is no need to choose tires that are too bald to prevent your baby from slipping. If there are no others, they can be coated with glue before painting and sprinkled with sand, allowed to dry and then painted.

A simple option for making a caterpillar

Craft tools and materials

Depending on how long the caterpillar made from a tire will be with your own hands, stock up required quantity tires But, basically, four are enough.

In addition to tires you need:

• a piece of wire and fiberboard;
• paints: black, green, yellow and red;
• tassels;
• self-tapping screws;
• jigsaw;
• screwdriver

Tire selection

For this option, three tires of the same size and one tire of a smaller diameter for the head are enough.

Having finished with the choice of tires, they proceed to cutting out circles (2 pieces), which cover the holes in the head (smaller tire). This is done using a jigsaw. A funny face is subsequently drawn on the fiberboard. It is screwed to the tire with a screwdriver.

To make the antennae, we used aluminum wire coated with insulation. To secure them, drill holes in the right place, thread wire through them and twist the ends.

After this, they move on to the longest task - painting the caterpillar from tires with their own hands. The tread is painted in grass color, and the sides are painted in bright yellow.

The head is painted the same color as the protector. On it, after the paint has dried, the face of the caterpillar is drawn.

All that’s left to do is dig the craft into the ground.

To do this, dig holes as deep as a spade bayonet. They put three tires in them, cover them with earth, and compact it well. The fourth tire with a painted muzzle is attached to the first “second floor”. You can see how it looks in the photo.

Looks like it turned out to be quite a fun craft! Such a nice caterpillar, installed on a playground, is well suited for children's fun.

Moreover, the children will not only enjoy playing with such a cute craft, but will also be able to relax after active games, comfortably sitting on the back of a good caterpillar.

Other tire crafts

In addition to it, on the site you can install a snowman of tires, a bunny, a car, a swing and many other crafts made from material that was doomed to be recycled, but has taken on a new life.

And, if a team of Smeshariki also appears, be sure that the guys will be delighted with their favorite cartoon characters.

Video: DIY tire caterpillar

57212 10/08/2019 7 min.

Owners of walk-behind tractors are increasingly going to all sorts of homemade products various components for this unit.

As a result we get attachments, made with your own hands, transforming a walk-behind tractor into a more powerful one, by installing a new engine, as well as many different modifications and additions.

Of course, all this is not due to a good life, because most owners of a walk-behind tractor strive not only to save on its purchase, but also to reduce the costs of its further operation.

In particular, many want to make homemade tracks for walk-behind tractors, thereby wanting to improve the cross-country ability of their units.

The resulting walk-behind tractor on tracks will perform a slightly different role in a person’s personal household, because it is already becoming a full-fledged vehicle, somewhat reminiscent of a caterpillar tractor.

Accordingly, a much wider scope of work opens up before him, which largely justifies this kind of independent alteration.

About the device

Tracked walk-behind tractors are much less common than their wheeled counterparts. The explanation for this is quite clear - wheeled walk-behind tractors Cayman, Patriot, Texas, Foreman, Crosser, Viking, Forza are more suitable for plowing land, i.e. its design is most suitable for working on the ground.

Thus, all conversions of a wheeled walk-behind tractor into a tracked walk-behind tractor involve the additional attachment of one wheel on each side. As a result, we get a 4-wheeled walk-behind tractor, on which you can already put on tracks (homemade or store-bought, for example, Buran caterpillar).

By the way, additional wheels can be made removable so that you can quickly turn it back into a standard walk-behind tractor for working in the garden. This can be achieved by attaching these wheels to an axle that we already have in stock, through a flexible or rigid transmission.

This solution is the most appropriate, because there is no need to weld additional fasteners.

As for the design of such walk-behind tractors, they are completely identical to wheeled walk-behind tractors:

• Engine. Tracked models use a more powerful 4-stroke engine, which has an axle locking function.
  

  This is important because it allows the crawler to turn in place without making a full circle to turn.

• Transmission. Gearbox, gearbox and clutch system - this standard set is also included in the design of tracked walk-behind tractors.
• Chassis. Here, in principle, everything is clear from the name - the design uses tracks instead of a wheelbase. As already mentioned, in the case of alteration, one roll is added to the existing pair of wheels on each side, on which a homemade caterpillar is already put on.
• Controls. They are located on the control handle, including various clutch levers, emergency engine stop, etc.

Before we begin to describe the method of making tracks yourself, it would not hurt to evaluate the offer of some special stores that sell walk-behind tractors and related materials. In particular, we will estimate the cost of some types of tracks for well-known walk-behind tractors.

Snowmobile attachments for the Neva walk-behind tractor

Thus, the tracks for the Neva walk-behind tractor, the price of which is about 28 thousand rubles, is a full-fledged snowmobile attachment. Seats for drivers can be purchased separately, thanks to which the Neva walk-behind tractor becomes similar to a mini tracked tractor, albeit with lower performance indicators.

Technical data:

• developed speed (with Neva walk-behind tractor) – about 18 km/h;
• total weight of the console – 37 kg;
• length – 100 cm;
• width – 60 cm;
• height – 34 cm;
• number of passengers – one driver and one passenger.

For more information about the caterpillar drive for the Neva walk-behind tractor, watch the video:

In addition, an attachment to a walk-behind tractor on tracks is available for sale, designed for attachment to the Agat and Salyut models. Its cost is 25-27 thousand rubles. In this design there is no possibility of attaching a driver's seat, which somewhat limits the possibilities of this device.

However, it is quite suitable for off-road and snowy driving. Snowmobile attachments on tracks to walk-behind tractors are quite common, as evidenced by a fairly large number various models in online stores.

Their distinctive feature is the ability to control them not only with two hands, following the walk-behind tractor, but also while sitting in a folding sled, which, however, must be purchased separately.

Considering that average price for such attachments is about 30 thousand rubles (plus the price of folding sleighs - about 5 thousand rubles), we can say that making tracks yourself is a fairly optimal solution for those who do not have the opportunity to spend extra cash for purchase.

Necessary materials

As mentioned earlier, to transform the Sadko, Don, Huter, Profi, Plowman, Champion, Carver, Husqvarna wheeled walk-behind tractors into a tracked walk-behind tractor, you will need a fairly powerful engine with axial locking.

Power is important because such a walk-behind tractor will be used on a fairly complex surface, the maneuverability of which requires additional technical data.

To summarize a little, we can highlight the main materials that we will need:

• The presence of the walk-behind tractor itself with a gearbox with a powerful 4-stroke engine with axle locking.
• A couple of extra wheels so you can pull the track on them.
• The homemade caterpillar itself, made from available materials.
• Depending on what material will be used in production, we may need two large car tires or transport tape.

Using these materials, you can make a fully functional crawler walk-behind tractor.

At the same time, you can make a full-fledged mini tractor on tracks if you add an additional cargo platform, or use it as an all-terrain vehicle in the snow by adding a platform on skids. In general, there is complete scope for imagination.

Step-by-step instruction

Many people ask the question - how to make tracks on a walk-behind tractor with your own hands? To answer this question, let's look at a few effective ways self-made tracks proven in practice.

From a transport tape to increase the cross-country ability of an all-terrain vehicle

One of the most simple methods It is considered the manufacture of a caterpillar from a transport belt using a bushing-roller chain. The ease lies in the fact that to make them you do not need to use a large number of tools and aids.

To extend the service life of our transport tape in the device of a caterpillar walk-behind tractor, you can sew it along the edges with fishing line, observing a step of 10 mm. To connect the tape into the ring we need, you can sew it along the ends, or use a hinge.

Particular attention should be paid to the thickness of the transport belt, because it directly depends on the degree of load on the unit. The optimal choice would be a tape with a thickness of at least 7 mm. In addition, we need to take care of an additional wheel on each side.

You can take it from an old car, but remember that the diameter must be identical to the wheel on the walk-behind tractor.

Tracked module made from a tire

Caterpillars made from tires for walk-behind tractors are also a fairly common homemade product, characterized by a highly reliable design. However, in order for the resulting crawler walk-behind tractor to be practical, you need to take care of finding the right car tires.

Owners farms are increasingly resorting to purchasing special technical devices- grain crushers, with the help of which you can process raw materials, thus preparing feed for food yourself. By following the link you will learn how to make a grain crusher from washing machine with your own hands.

On the domestic market of agricultural machinery there are various options cultivators not only of Russian, but also foreign production. The Mantis cultivator is a reliable and practical technique that will last for decades.

IN Lately Small-sized agricultural machinery is very popular, allowing it to do the same work as their “big brothers”, but at the same time they cost an order of magnitude less. everything about various types and characteristics of mini grain harvesters.

In particular, they must have the necessary tread pattern, preferably from tractors or large machines. The tread pattern is very important because it acts as a lug and also increases the track's grip on the surface.

Let's divide the manufacturing process into several steps:

• Having found suitable tires, we need to cut out a track for the tracks. This is quite a labor-intensive job that will take a lot of time.
• For cutting, you can use a well-sharpened shoe knife, which should be soaked in a soapy solution from time to time - this will help cut the rubber better.
• You also need to cut both sidewalls off the tires. To simplify the process, the sidewall can be cut using electric jigsaw with fine teeth.
• If necessary, remove excess parts from inside the tire. This manipulation must be performed if the track is too hard from the inside.

The advantage of this method is that there is no need to connect it into a ring, because the tire already has a closed structure. This increases the reliability of such tracks, which is quite important under heavy load conditions.

However, such caterpillars are obtained of a rather limited length - exactly along the length car tire.

How to make a homemade caterpillar from belts and chains

All-terrain vehicles on tracks from a walk-behind tractor can be made using the most ordinary belts with a wedge-shaped profile. The belts are connected to each other by means of a lug, attached to the belts using rivets or screws.

Another way is to make a track from chains of the same size. Many summer residents have similar material in bulk in their garages, which simplifies the search process. The entire manufacturing process comes down to the following points:

• Take two chains of the same size.
• The last links of these chains must be opened and then connected into a closed ring.
• Next, we clamp the links and weld them.

The chains are fastened to each other using lugs, which can be made from ordinary steel plates required thickness. They are connected to the chain using bolts.

Motoblock on Buran tracks

If you do not want to make caterpillars yourself, you can borrow one from old technology. For example, a walk-behind tractor on Buran tracks performs quite well.

It is advisable to use old part, because the new Buranovskaya caterpillar will cost quite a lot, and the purpose of such alterations is maximum savings on costs.

Additional tips and warnings for making your own goose

Before you start making homemade caterpillar, you need to clearly understand its necessary parameters. The fact is that if a very high caterpillar is manufactured, the center of gravity of the walk-behind tractor itself will be changed, which will inevitably lead to certain problems when turning, i.e. the unit will fall on its side.

To avoid this, the second driven axis needs to be increased by a few centimeters. You can also slightly expand the wheelbase of your existing walk-behind tractor. To do this, you can purchase a bushing in a special store, and then install it on the drive shaft.

In addition to the engine power requirements, it is worth paying attention to its cooling system. The fact is that air cooling does not cope very well under high loads, which leads to significant overheating of the motor.

Thus, it is better to give preference to a water-cooled engine, which shows more stable performance.

Conclusion

Attaching tracks to a walk-behind tractor allows you to significantly increase the cross-country ability of this device. This leads to an increase in the range of potential jobs that the resulting walk-behind tractor can handle. In other words, the tracked base in some positions outperforms the conventional wheelbase.

However, such a modification of the walk-behind tractor is not suitable for all owners of these units. First of all, we're talking about about the special requirements for the engine used, which must have sufficient power.

As for the conversion process, they are quite possible at home, so this is a significant alternative to tracked attachments sold in stores, like many others

To increase the throughput capacity of a walk-behind tractor and use it as an all-terrain vehicle or snowmobile, you can equip it with tracks. You can buy them ready-made, but they are expensive, and it’s not always possible to find them the right option to your walk-behind tractor. There are several ways to make a caterpillar for a walk-behind tractor with your own hands.

How to make a caterpillar on a walk-behind tractor with your own hands

If you wish, you can independently modify your walk-behind tractor, turning it into a tracked all-terrain vehicle or snowmobile. The main rule is that you should consider what work the tracks are intended for in order to choose the right material, because they must be not only durable, but also extremely light.

Having available materials and correctly calculating the length of the caterpillar, you can make it yourself using simple improvised means.

First of all, you need to equip your walk-behind tractor with an additional pair of wheels. A caterpillar track will be put on each side pair.

The length of each of the two goosenecks will be equal to the circumference of one wheel and the distance between the axles of each pair of wheels, multiplied by two.

Important: the wheels on the walk-behind tractor must be the same diameter.

Materials for homemade products can include:

• conventional conveyor belt and bush-roller chain;
• car tires;
• belts and chains.

So, let's look at several options for making a goose yourself, depending on the material used.

From a conveyor belt

This method is the simplest because it does not require a large number of special tools and auxiliary materials.

• When choosing a tape for a caterpillar, give preference to a strip whose thickness will be at least 7 mm - after all, it bears a fairly large load. The coupling with moving parts will be provided by a bushing-roller chain.
• To give the tape strength and increase its service life, it is recommended to stitch it along the edges with fishing line using frequent stitches in increments of about 10 mm.
• It is also necessary to sew the tape along the ends to connect it into a ring required diameter, or use hinges reminiscent of a piano canopy for greater reliability.
• Make sure that the additional wheelset that you install on the walk-behind tractor frame is the same diameter as the main wheels on the walk-behind tractor.

From a tire

It’s enough to simply make a durable, reliable gooseneck for a walk-behind tractor from a tire. The manufacturing process from a car tire will not take too much time, since it does not need to be stitched and lugs built up - the tire itself is a closed structure with a tread for traction.

Tires from truck or tractor wheels that have a pronounced tread pattern are best suited for caterpillar tracks.

The manufacturing process is divided into several stages:

1. Using a very sharp knife dipped in a soapy solution to enhance the cutting ability on rubber, cut the gooseneck tape to the required width.
2. The sidewalls of the tire are cut off with a jigsaw using a fine-tooth file.
3. Hard parts on inside tires are also cut using a knife or jigsaw.

However, here there are several points that you should pay attention to:

• The tread pattern must be clearly defined, since its reliefs are a kind of lugs that increase the adhesion of the moving mechanism to the surface.
• The length of such a caterpillar is limited by the diameter of the tire, so before attaching an additional pair of wheels, you should take this into account.

From belts and chains

In order to make a tracked all-terrain vehicle from a walk-behind tractor, you can use ordinary belts with a V-shaped profile. The belts are connected to each other by lugs attached to them with rivets or screws. Thus we get a belt track.

To make a track from chains (chain tracks), you need to take two pieces of the same chain required length.

• The end links of both segments are unclenched in order to connect them into two closed rings.
• The loosened links are clamped again and then welded to secure the fastening.
• Sections are cut from steel of the required thickness that will serve as lugs.
• The lugs are bolted at both ends to the links of both closed chains, thus forming a raised track on the walk-behind tractor.

Homemade tracks for caterpillars

Tracks for a homemade goose can also be made independently from any suitable material. The main thing to consider is what load you are going to give to your walk-behind tractor.

From plastic pipes

You can use pieces of plastic pipe as tracks for a snowmobile gooseneck. For this purpose, plastic water pipe Cut No. 40 into pieces equal to the width of the caterpillar. By using circular saw saw each section lengthwise into two equal halves, or use circular saw on wood.

The resulting tracks must be attached at regular intervals to the conveyor belt with No. 6 furniture bolts with large hemispherical heads.

From wooden blocks

Sometimes, if the load on the goose is not very large, you can use birch blocks as tracks. They are not particularly strong for heavy loads, but they are lightweight, affordable, and a track with such tracks can be repaired in any convenient location.

Iron tracks

The most reliable are metal tracks made of high-quality iron. Metal pipes or profiles cut into pieces of the required length are suitable for this purpose. Profile metal pipe cut according to the same principle as plastic, and attached to the conveyor belt with bolts.

However, metal tracks, despite their noticeable strength, also have their drawbacks: they are heavy compared to plastic and wood, and can bend during use. To straighten the track, you will need to remove it from the gooseneck, and this is a labor-intensive operation.

When choosing the material from which the track tracks for your mini-all-terrain vehicle will be made, you should evaluate the degree of load and operating conditions. Light polyethylene or wooden tracks are perfect for overcoming snowy expanses, but to use a walk-behind tractor as a mini-tractor, it is still better to make a caterpillar with metal lugs.

Buy a hitch and a trailed one for a walk-behind tractor in online stores

Do-it-yourself caterpillar for a motorized towing vehicle

A motorized towing vehicle, popularly called a “motor dog,” is ideally suited for use in northern latitudes with good snow cover. Using a walk-behind tractor, you can independently make an alternative to a dog sled, a high-speed tracked vehicle that can tow a sled with a person or a small load in the snow.

Making a caterpillar for a motorized dog with your own hands is not at all difficult.

You can use an old gooseneck from a Buran snowmobile. To increase chassis, you should cut it in half and build it up using inserts. The tracks can be carriages from the old Buran. Three carriages with rollers are enough. They also need to be sawn and extended with inserts.

In the absence of old spare parts, a caterpillar for a motorized towing vehicle can be made from improvised materials using one of the methods described above. For example, from a conveyor belt.

For production you will need:

• conveyor belt with a width of 22 cm;
• metal bars for reinforcement;
• hardwood timber blocks for track tracks.

We bring to your attention a video showing the caterpillar manufacturing process.

Making a caterpillar for a walk-behind tractor is a simple process, although it requires sufficient quantity time. It is also necessary to make every effort and skill to ensure that all links of the goose are located at an equal distance from each other. This will help to avoid distortions and sliding of the caterpillar track from the load-bearing surfaces.