The advantages of paper wallpaper are their “breathing” abilities and low cost. The first property keeps the walls in good condition: fungus and mold do not form on them, and they are the most environmentally friendly finishing material. The range of patterns differs not only in patterns and shades, but also in texture: there are embossed wallpapers consisting of 2 layers of paper. They are called duplex, have a stronger base and, accordingly, a longer service life.

Simple single-layer wallpaper (simplex) has a fine structure, as a result of which the walls require careful preparation before gluing. It is a perfectly flat and smooth surface that conveys all the beauty of paper wallpaper, otherwise cracks and differences in the plaster will be clearly visible through the paper.

Preparation for gluing

The work can be easily completed by one person. The main condition for a quality result is following the standards that determine how to properly glue paper wallpaper without disrupting technology. Glue should be purchased for lightweight wallpaper, for example, KMC. Typically it is prepared in the following way:

Thickened glue should not have lumps; you can get rid of them by thoroughly mixing it again. Rolls that do not require adjustment of the pattern are cut into strips, the length of which is equal to the height of the wall + 5 cm for the addition. The excess is cut off during gluing with a wallpaper knife along the line where the floor and wall meet. For convenience, a metal spatula is applied.

The last stage of preparation is priming the surface for better adhesion of wallpaper and plaster. The primer is applied with a wide brush or roller from the ceiling to the floor. Corners should be treated especially carefully, as they may cause the canvas to peel off after drying. It's important to wait completely dry primers.

Gluing paper wallpaper? Features of the work

The finishing material tends to tear after getting wet if handled carelessly, so all actions must be performed carefully and carefully. First of all, glue is applied to the wallpaper strip. It unfolds on a table or on a clean floor with the wrong side out. The glue is applied with a roller or brush, while ensuring that there are no dry islands, especially at the edges.

• take the edge of the strip and fold it towards the middle;
• repeat the action from the opposite edge;
• Fold the resulting fabric in half.

Thus, the strip is folded in four, the front side is not smeared with glue, but the back side is saturated, folded inward. You should wait 2-3 minutes, and this time will be enough to apply glue to the wall (from top to bottom along the width of the wallpaper strip). Next, the canvas is applied to the wall. There is no need to unroll it in advance, just turn the edge 1/4 of the canvas and attach it to the wall directly under the ceiling. Then the strip must be gradually unfolded, pressing it against the wall.

Having glued the wallpaper, use a special spatula or dry roller to smooth it from the center to the edges. Excess glue extending beyond the strip on the sides should be blotted with a soft cloth. The peculiarity of paper wallpaper is that it always shrinks, so the strips are glued overlapping. The width of the overlay is 0.5 cm. This technique eliminates the gap that forms when the paper dries if the strips are glued end-to-end. Thus, the next sheet is applied to the wall in the same way as the previous one, but with an overlay of 5 mm.

The sequence of work is as follows:

• First, the walls from the window to the door are covered;
• then short sections: above the window, door, under the windowsill.

If the wallpaper has a large pattern, you should follow the step size, which ensures that the pattern matches. It is usually indicated on the packaging, but it is better to control it yourself when cutting the roll into strips. During and after work, it is imperative that there is no draft in the room: the window and door must be tightly closed. If this simple rule is not taken into account, the paper wallpaper will dry too quickly and may peel off.

Features of gluing to the ceiling

Finishing the ceiling with paper wallpaper is an easy way to give it freshness and newness in a short time. However, the work is physically more difficult to carry out than pasting walls, since your arms must be constantly raised above your head. That is why you may need an assistant to support the canvas. Experienced craftsmen It is recommended to carry out gluing by folding the pre-spread canvas into an accordion shape. Then press it to the ceiling, gradually unfolding it and moving from one wall to another.

It should also be taken into account that paper wallpaper is easily torn, so there is no need to pull on the canvas that is already glued to the ceiling. If it is noticed that it does not fit correctly, for example, it is slightly skewed, it will have to be completely peeled off and reattached. A guarantee of even gluing of the first strip will be a strip drawn in advance on the ceiling with a pencil, indicating the place of its application. Leveling and removing air from under the wallpaper is done with a roller or a special spatula.

The question of how to glue has arisen for everyone who has at least once done own apartment repair. It would seem that there is nothing complicated about this, but not everyone’s results meet their expectations. Applying wallpaper correctly is an art, and with the advent of new types, the technology for working with them also changes. But paper wallpaper is always at the peak of popularity. They are loved for their variety of colors and patterns, low cost, environmental friendliness and ease of operation. They are suitable for either, or office.

Often duplex wallpaper has a textured surface. The pattern is obtained by rolling a textured roller under pressure over a still damp paper web. After this, paint is applied. Such duplex wallpaper is called embossed. They should be glued end to end.

• Embossed wallpaper is the most durable among paper wallpapers. They are not only durable, but also have high decorative qualities.

Non-woven

Paper products are particularly durable and have a pleasant-to-touch surface. non-woven wallpaper. They are easy to glue, since the glue is only applied to the wall. Among the features of this type is durability; they can be repainted several times.

Advice! When purchasing colored wallpaper with a pattern, it is important to ensure that all rolls are from the same batch. Shades may vary greatly, which will affect the final result.

Vinyl

Vinyl wallpaper on paper based the most wear-resistant. The top layer is a vinyl coating of various textures and colors. This wallpaper is durable and heavy. Visually, they can be easily confused with embossed paper ones, but the latter are inferior in quality.

Selecting wallpaper glue

What glue should I use to glue paper wallpaper? It all depends on the thickness of the coating. A universal option is cellulose-based CMC glue. It is suitable for both thin and embossed, even for vinyl wallpaper. The only difference is in the concentration of the solution.

Important! The thinner the paper, the more liquid the composition should be.

When purchasing special adhesives, you should pay attention to the manufacturers' recommendations. Adhesive for paper backing is usually inexpensive and comes in three types: for light, medium and heavy wallpaper.

• For embossed, non-woven and paper-based vinyl rolls, vinyl adhesive works equally well.

Advice! Any wallpaper can be pasted over using PVA or bustilate. These compounds guarantee reliable adhesion of the paper to the wall, even for heavy canvases.

Wallpapering

Before gluing paper wallpaper, you need to decide how it will be done - end-to-end or overlapping. Typically, a roll of paper has a side edge. Thin wallpapers can be glued overlapping, due to the edges of the canvas they will fit well to each other.

Advice! If the fabrics are thick or embossed, the edge will only get in the way, and unaesthetic stripes will appear at the joints. In this case, it is better to cut off the edge and glue the wallpaper itself end-to-end.

Non-woven and vinyl wallpapers are also glued end-to-end; the technology can be seen in the video.

Advice! On the wallpaper label you can find information about how many centimeters are required to fit each strip. This data must be taken into account when calculating the required number of rolls. When purchasing, it is always better to take one more than required.

Preparing the walls

Before you start gluing, the walls need to be carefully prepared:

1. . Use a spatula to carefully pry off the joints and peel off the fabric. If the wallpaper is firmly glued, then it should be moistened with warm soapy water. In some places you can make cuts so that water gets onto the glue.
2. Clean painted walls with sandpaper or wire brush. All peeling areas must be sanded thoroughly. Water based paints or whitewash must first be soaked and the residue removed with a spatula.

1. The cleaned base must be cleaned of dust and inspected for defects - unevenness, cracks, etc. All defects must be treated with a primer and puttied. When the putty has dried, sand it down to the same level as the wall, and then coat it with primer again.
2. Wallpaper will stick better if the walls are first coated with a primer. This may be a special penetrating composition for water based or highly diluted glue.

Tools

The right tools will make the wallpapering process easier:

1. Scissors or utility knife.

1. Pencil and tape measure.

1. Wide brush and roller.
2. Glue tray.
3. Sponge and soft cloth.

Marking and cutting

Measure the height of the wall. Roll out the roll with the wrong side up and make a mark on it corresponding to the measurement. Cut into several strips of the desired length.

Advice! If the ceiling or floor is uneven, then when cutting it is worth adding another 5-10 cm to the height of the wall, this will help to stick it accuratelystripes. When cutting wallpaper with a pattern, you need to take into account the tolerance. Add a value from 5 to 30 cm to the length of the wall and cut the wallpaper into appropriate pieces.

Fold each piece of paper with its short sides towards the center and leave for a few minutes so that the paper is well saturated with glue.

This must be done before gluing paper-backed vinyl wallpaper or other severe types. This action will help avoid bubbles and prevent peeling.

Advice! It is better to glue thin wallpapers immediately, in some cases, as with, applying glue only to the wall.

Advice! Before gluing or heavy embossed ones, it is advisable to also apply glue to the walls using a roller.

When the strips are saturated, you can start gluing them:

1. The first strip is applied to the corner closest to the window.
2. The canvas is leveled from top to bottom. First, press the middle and level it to the edges using a dry soft fabric. While it's smoothing out top part, there is no need to unfold the bottom.
3. Excess glue must be removed immediately with a damp sponge.
4. Each strip is tightly fitted to the previous one, butt or overlap, taking into account the tolerance.
5. The joints need to be ironed additionally, preferably with a rubber roller. This way they will be less noticeable.
6. IN last resort the doorway is covered.

Advice! When gluing wallpaper, you should make overlaps on the ceiling and floor - 5 cm in each direction. When the canvas is smoothed, you can cut off the excess with a sharp stationery knife.

Wallpaper is the most common finishing material. Today they are presented in a wide range on the market. This material is used both for cosmetic and European-quality repairs. It will be useful for every owner who wants to change the design of the walls to know whether the overlap is correct.

In contact with

Features of the work

You can find two main types in the store classic wallpaper. Simplex is a single-layer material that has a small thickness and is relatively inexpensive. Duplex like more modern look, is a two-layer product. On upper layer a pattern is applied. Duplex options can have a foamed, textured or smooth surface.

More recently, American wallpaper paper embossed. Their difference lies in environmental friendliness and high performance characteristics. They are presented in a wide range of colors. Thanks to these advantages, the material is ideal for decorating children's rooms and bedrooms.

The materials are glued using a similar technology. Of course, there are some peculiarities here. It all depends on the type of material used. Thus, simplex products have a small thickness, so the walls must have a perfectly flat surface. The small thickness also has some advantages. Simplex materials can be glued both end-to-end and overlapping. As for duplex products, they are laid only end-to-end.

The choice and application of glue is also important. The applied glue is left for 15 minutes to thicken.

Attention! When purchasing a material, you should first ask your consultant about the specifics of its gluing. This is especially true for American counterparts.

How it is produced. To carry out quality work, it is necessary to take into account some gluing features. You should start with the choice of glue.

The peculiarity of paper wallpaper is that it is susceptible to any option. This can be non-woven glue or homemade paste. The latter is used when it is not possible to purchase a regular adhesive.

The paste is made on the basis of water and flour, it is well suited for gluing more dense materials. But anyway, what glue to use for paper wallpaper?

Special glue, which is sold in powder form, is very popular. Before carrying out finishing work, it is necessary to prepare the adhesive solution in advance. It's being flooded sufficient quantity water and left in the room where repairs are being carried out. The powder dissolves completely in 10 hours or more. The composition is stirred periodically, which will speed up the dissolution process.

Surface preparation

When decorating a room. The final result will depend on this - aesthetic appearance and coating strength.

Wall preparation is carried out in the following sequence:

1. . This applies to rooms that were previously subject to cosmetic repairs. In new buildings this point is omitted. Old finishing material must be carefully removed from the walls. This process is very labor-intensive and dusty. To speed it up, you need to stock up on all the necessary tools.
2. Padding. When the old coating is removed, the walls are treated with a primer solution. This will improve surface adhesion and eliminate dust.
3. . With its help, irregularities are eliminated. If the wall is smooth and has no flaws, then the putty is applied thin layer. This will create an ideal base for the canvases and ensure their strong fixation.
4. Priming is carried out at the final stage of wall preparation. It is best to do this a few hours before finishing work, as the surface must dry.

In this way, the walls are prepared for gluing. To ensure the quality of finishing work, it is necessary to strictly follow the given algorithm.

Cleaning the surface of old wallpaper

Required Tools

When carrying out finishing work, you will need tools.

Among the main ones it is worth preparing:

• pencil,
• ruler and tape measure,
• scissors,
• stationery knife,
• bucket,
• glue tray,
• rollers and brushes,
• wallpaper spatula,
• stepladder

The presence of all these tools and devices will allow you to quickly and efficiently finish the job. Particular attention should be paid to the choice of rollers. To do this, you will need several types: a paint roller is used to apply glue to the walls, and a joint roller is used to roll the joints of the canvases.

Technology

After with preparatory work will be completed, you can begin to directly decorate the room. DIY paper wallpapering begins with cutting the material.

Roll cutting

You need to approach cutting the canvas very carefully. This is especially true for materials with patterns; you must try to glue them so that the pattern matches. In the case of plain materials, gluing can be done without any problems.

First you need to unwind the roll on the floor and cut off individual strips according to the height of the walls. If the products are monochromatic and do not have a pattern, then you can cut several pieces at once. Otherwise, you will have to select a pattern. To do this, you need to unwind the roll and attach the cut piece to it. This will allow you to compare the drawing.

You can use a utility knife or sharp scissors to cut the paper. A cutting line is drawn in advance, which will allow cutting to be done efficiently and evenly.

Where to start

During finishing work, it is important to decide where to start finishing.

Today there are several options for solving this problem:

1. From the door, the panels are glued strictly vertically. To make your work easier, you can use this as a guide. doorjamb. In this case, you need to check with a plumb line.
2. From the corner. It is recommended to use this method only if the corners in the room are perfectly even.
3. From the middle. This technology for gluing paper wallpaper allows you to improve the aesthetics of the coating. But here you need to take into account the length of the wall and the width of the canvas.
4. From a major landmark. If there are several windows in the room, then it is better to start gluing from one of them. In the future, this will avoid problems with joining the panels.

The choice of gluing method must be approached very carefully. The aesthetics of the coating will depend on this.

You need to start gluing wallpaper from the window

How to apply glue

The glue is applied to the back side of the canvas over the entire area. Dry areas are not allowed. Dense products are folded in half. After this, glue is applied top and bottom, as well as at the joints. You can also lubricate the wall over the entire area where the canvas is attached.

Of course, lubrication vertical surfaces glue is not always used. In this case, you need to study the instructions supplied with the products. Also, the answer to this question can be depicted in the form of special pictograms on the label.

Angles

Often, when gluing in corners, people make serious mistakes, which leads to a decrease in the aesthetics of the finish. If the corner is perfectly flat, then there will be no problems with pasting it.

So, how to glue paper wallpaper correctly:

• stick the canvas in the corner so as to cover the adjacent one, and no more than 2 cm;
• carefully trim off excess fabric with a stationery knife;
• finish the adjacent wall.

If the angle is uneven, the grip can be up to 8 cm. In places where the paper wrinkles, you can make several cuts. This will remove any unevenness.

Wallpapering corners

How to get rid of bubbles

Bubbles sometimes form during gluing, how you can eliminate them.

Today there are several methods to solve this problem:

1. Smoothing. Using a dry cloth or a special spatula, smooth the newly pasted canvas. In most cases, this will remove bubbles and unevenness.
2. Using a syringe. Glue is taken into it and carefully injected into the problem area. After this, the canvas is smoothed, pushing out excess adhesive.
3. Using a razor. This method is used in cases with large bubbles. IN problem area an incision is made with a razor. After this, glue is injected. All work must be done very carefully, as there is a risk of cracks.

Finishing without bubbles is quite difficult, but these methods will solve the problem.

Smoothing with a special spatula

Butt gluing

It is quite difficult to glue paper wallpaper end-to-end, but it is worth considering some nuances. This is especially true for direct joining of canvases.

So, how to properly glue paper wallpaper:

• this method should be used on surfaces without differences;
• during work, there is no need to open windows and doors, otherwise this will lead to rapid drying of the paper and divergence of the joints;
• indoors you can create a greenhouse effect using a bowl of water;
• when joining, you need to move the entire canvas from the edge;
• It is not recommended to stretch the fabric too much, since after drying they will tighten and cracks will form at the joints;
• drafts and sudden temperature changes will reduce the integrity of the coating;
• The glue is applied in an even layer over the entire area.

Now you know how glue paper wallpaper end to end.

The peculiarity of simplex products is that they are small in thickness and have low strength.

These features should be taken into account when carrying out finishing work:

1. Thin wallpaper Recommended for use as an ideal finishing touch smooth surfaces. Due to their small thickness, they cannot hide surface unevenness.
2. The glue is applied very carefully. You should not leave the material in this condition for a long time, otherwise it will become wet and damaged.
3. Finishing is carried out both end-to-end and overlapping.
4. Simplex products have low strength, so you need to work with them very carefully. Especially after applying glue.

These are the basic rules for working with thin fabrics. Of course, do not forget about preparing surfaces for finishing. The aesthetics of the coating will depend on this.

Wallpapering at the joint

Repair is a labor-intensive process, so many people try to finish it as quickly as possible.

How fast stick:

1. The right choice of products for gluing. To spend Finishing work quickly, it is worth using plain materials.
2. Savings are not appropriate. Cheap products have low strength, so problems may arise with them. It would be better to opt for quality materials.
3. There is no need to carry out work alone, as this will take quite a lot of time and reduce the quality of the finish.
4. Self-adhesive products on back side have a coating of dry glue that is activated when exposed to water.
5. A special glue, the use of which will not only improve the quality of finishing, but also the time it takes to complete it.
6. Preparing the walls. If the surface is perfectly flat, then the work can be done easily and quickly.

Useful video: how to properly glue paper wallpaper?

Now you know, how to hang paper wallpaper without seams or overlap with your own hands. With a little effort, you will get beautiful, smooth walls.

Paper wallpaper remains the most common and at the same time inexpensive option wall decoration inside the apartment. Their main advantage is low cost, ease of operation, and a good, aesthetic result.

Paper wallpapers are made in a wide range of types and types:

1. Smooth. They are made entirely of paper, the design is applied using the usual printing method.
2. Double (duplex wallpaper). They are glued together: one layer is the base, the second is the drawing itself. They have an additional coating that protects against external mechanical influence; during production, the layers are pressed together. Duplex wallpaper is more durable and is not afraid of moisture and direct rays of the sun.
3. Embossed. They are also double-layered, but the pattern is three-dimensional and the relief is clearly visible.
4. Structural. The design is made by adding various crushed materials to the paint - sawdust, sand, nut shells.
5. Foam wallpaper. Canvas with a three-dimensional pattern made using special technology.
6. Moisture resistant. Covered with a special water-repellent layer that protects against slight exposure to moisture.

Advantages and disadvantages

Despite the huge assortment presented in construction stores, paper wallpaper for walls can be divided into two main types:

• simplex (single-layer);
• two-layer or duplex wallpaper.

Their main advantage is environmental friendliness. Paper webs, as well as the glue used to work with them, are made from natural ingredients and are completely non-toxic. Therefore, paper wallpaper can be used even in children's rooms, where the environmental component is very important.

Paper wallpaper - environmentally friendly pure material, which is often used to decorate children's rooms

The disadvantage of all paper wallpaper, regardless of type and texture, is impracticality and poor resistance to external influences.

Given the very strong susceptibility to getting wet, paper wallpaper cannot be used in rooms with high humidity such as the bathroom or kitchen.

In addition, the service life of such finishing is quite short. Usually, re-repair has to be done after 5-7 years. Also a significant drawback that significantly complicates renovation work, is the small thickness of the canvases, forcing you to carefully prepare the walls before pasting. Through paper wallpaper, even embossed, all the imperfections of the wall surface will be clearly visible.

So, you have chosen the design that suits you, cleared the room and got to work. DIY paper wallpaper sticker has some features. To hang wallpaper correctly, without subsequent surprises, you should consider some general recommendations, which will allow you to avoid errors during the work process:

1. Study the recommendations from the wallpaper and adhesive manufacturer. On the roll itself you will find information on how to glue this type of paper wallpaper. Manufacturers also indicate whether to glue them end-to-end or overlapping.
2. Prepare the walls, this is the most important point, give them some time Special attention. The surfaces must be thoroughly cleaned, and, if necessary, all possible irregularities and cracks must be puttied. A primer must be applied to the prepared walls. You should start gluing only after the last one has completely dried.
3. All switches and sockets are disconnected from the network and freed from external boxes; they can be put back in place after completion of work.
4. The gluing of the first strip must be approached with the greatest responsibility; the quality of gluing of all other strips will depend on the correctness of the work.
5. There should be no drafts in the room where the work takes place, otherwise all the work will go down the drain. The canvases may simply peel off.
6. Wallpaper coverings made of paper, which are not intended to be glued end-to-end, are equipped with a special edge, but it should be noted that gluing with an overlap is only suitable for thin sheets. Thick wallpaper, such as embossed duplex wallpaper, is best glued end-to-end, so the seam will be less noticeable. In this case, if there is an edge, it will need to be cut on both sides.

Wallpapering difficult areas

People who do not have construction experience often wonder how to glue paper wallpaper in the corners so that there are no folds and the canvas holds firmly. First of all, you need to take into account that in such places it is better to glue the wallpaper overlapping. To do this, when gluing the strips, make an overlap of 1–2 cm onto the adjacent wall, after which the next strip is glued end-to-end to the corner. Embossed and other embossed duplex paper wallpapers require a different approach. They need to be overlapped, followed by trimming along the double joint and removing excess material. More information about that.

Pasting walls with paper wallpaper. Sequence of work

Tools, utensils and devices that need to be prepared in order to work efficiently:

• a special knife (ask in the store) or wallpaper scissors. These tools must be in good condition and well sharpened;
• a pencil, or better yet more than one. You definitely need a tape measure and a long meter ruler;
• a bucket or any capacious container for glue, brushes and a regular fur roller for applying the adhesive solution;
• special roller for wallpaper;
• sponge for removing excess glue;
• pieces of clean cotton rags.

Cutting and marking the wall

To cut the canvas correctly, you need to roll out the roll inside out and measure the height of the wall, adding about 5 centimeters. Paper wallpaper without a pattern is cut into several strips at once; if there is a pattern, you need to ensure that the pattern matches. If you are not sure that the walls in the entire room are the same height, each strip should be cut with a margin of 7-10 cm.

In order for the canvases to be glued correctly vertically, the walls will have to be marked. You need to start marking from the window, clockwise.

Preparation of canvases

Before gluing paper wallpaper, they must be thoroughly lubricated with glue. It will be correct to apply glue to the canvases, spreading them out on big table. But if this is not the case, try to keep the area on the floor always clean and the glue does not get on the front side of the wallpaper.

Place several strips so that the distance from the edge of the table is about two centimeters, after which, on top, butt to the edge, place the strip that you will work with first. This is done so that when spreading the canvas on the surface of the table, glue does not get on and stain the wallpaper with front side.

The glue is applied evenly, with a roller or brush, over the entire area, starting from the middle. You need to make sure that there are no missing sections. If the glue is applied correctly, there will be no bubbles.

The strip is folded into three quarters, starting from the top, and left for 10 minutes to soak. The glue should be well absorbed; you want the wallpaper to literally get wet.

If the canvases are very thin, then they can be applied to the wall immediately after applying the glue. Any glue that gets on the front side should be removed with a damp sponge without waiting for it to dry, but you should not rub it.

We move the next strip to the edge of the table and repeat the whole process again.

Pasting

Correctly gluing single-layer or duplex paper wallpaper to walls is actually not difficult, with due skill and accuracy. When gluing with an overlap, work begins from the window, this is a well-known rule. If there are several windows in the room, work begins on the south side. Thick embossed sheets should be carefully glued end to end.

The surface must first be marked, then straighten the folded wallpaper strip and glue its upper half. Gluing the first strip is the most critical stage, it doesn’t matter whether the wallpaper is glued end-to-end or overlapping. It must be perfectly vertical, since this determines how everything will go further. Once you are sure that everything is going as it should, release the remaining part and glue it to the wall.

Pressing is carried out with a wallpaper brush or roller, the strip is carefully smoothed from the middle to the edges. The junction with the floor at the baseboards is an important area. To obtain a satisfactory result, press the canvas against the baseboard with a spatula, and cut off the excess.

Both embossed and smooth paper wallpaper will lie perfectly flat on the wall, without the slightest bubbles, if the wall is well treated with glue beforehand. If necessary, carefully coat the edges with a clean brush, and carefully smooth the canvas with a roller or rag. If you do everything correctly and carefully, then when the finish dries, the result will definitely please you.

Sometimes the question arises: is it possible to do repairs without helpers, alone? Alas, it’s too much for one to glue wallpaper coverings highly undesirable. Not to mention it's more fun to work with a group, the process of covering walls requires at least two pairs of hands. This is not to say that this is completely impossible, but the result will be such that you will also have to admire it alone, since it will simply be a shame to show it to others.

Still have questions? Watch this video.

And prepare the stripes according to it. Arrows on both sides of a vertical line at the same level (straight marking) indicate that the pattern needs to be drawn up. At different levels - they are glued in reverse order, with each subsequent strip directed in the opposite direction. An arrow on one side indicates that there is no need to adjust the pattern.

The list of other basic rules for pasting walls contains the following points:

• All remnants of the previous coating are removed from the panels with a spatula, after which the surface is wetted, which is necessary for better adhesion.
• The glue is diluted according to the instructions or purchased ready-made.
• They begin to smear the strip first, and then the wall panel. The edges of the strip must be processed.
• Start applying from the top. At the same time, the wallpaper is folded. You need to glue the paper strips from the corner, aligning them vertically with a plumb line or level.
• Use a rubber roller or a dry cloth to smooth the fabric. To expel air and excess glue, do this from the center to the edges.

The paper will shrink as it dries. To prevent cracks from appearing, the strips are glued with an overlap of 0.5 cm. Subsequently, when the paper dries, the wallpaper will shrink.

It is necessary to apply glue first on paper so that during the time it is applied to the wall, the paper wallpaper has time to become saturated. If you buy ready-made wallpaper glue, before gluing paper wallpaper, mix it thoroughly, achieving a uniform consistency. The main thing is to choose the right composition to ensure reliable bonding.

What wallpaper glue is suitable for paper wallpaper?

The correct choice of glue ensures that after drying there will be no yellow spots, paper wallpaper will not fall off, but when it comes time to change it, it will easily come away from the wall. You need to choose based on the type of paper wallpaper, depending on whether it is simplex or duplex:

• Simplex. For thin paper single-layer wallpaper, compositions made from cellulose or cotton products are used. Universal ones are also suitable.
• Duplex – two-layer paper. Wallpaper is used for painting. They are heavy and thick, which requires the use of non-woven glue or CMC.

Can be glued to vinyl wallpaper composition. By adding PVA to it, they achieve greater adhesion strength. They also use bustylate or pure PVA. All information about the mixing technology is on the packaging. If it is a special adhesive for paper wallpaper, this should be indicated.

What tools will you need?

To prepare in advance, you need to purchase and prepare:

• container for mixing the adhesive mass;
• wide rubber roller;
• narrow roller and dry rags;
• spatula for mixing glue;
• wallpaper knife and scissors;
• level or plumb line;
• pencil or ballpoint pen;
• a brush with a wide blade.

Once everything is at hand, begin preparation.

Proper preparation for gluing

Once the glue is prepared, you need to get everything ready. Otherwise, you will have to throw it away as it will set and become unusable.

The preparatory process is as follows:

• So as not to get dirty flooring, it is covered plastic film. It is important that it is clean.
• The electricity goes out.
• The covers of sockets and light switches are dismantled.
• The adhesive composition is prepared.
• If there is not enough light, the socket connectors are sealed with tape, which is then removed.

How to dilute glue correctly?

Before gluing paper wallpaper, you need to cut it into strips and prepare glue. The technology is that the dry mixture is poured from an unpacked pack into a dry, clean, deep container. Water is also introduced there. In this case, you need to constantly stir until a thick, sticky mass is formed. The proportions are indicated on the packaging. Ready mixes stir enough.

IMPORTANT! Prepare enough glue to enough for 4-5 stripes. Otherwise the residue will thicken. Do not add water to make it liquid again. This mixture will not hold the wallpaper on the wall.

Surface preparation

It needs to be cleaned of the remnants of the old coating. You cannot glue paper wallpaper over whitewash and paint (oil or water-based). The surface must be cleaned of dust. Old wallpaper is torn off, glue residues are cleaned off.

Can be glued to the surface:

• covered with newspapers;
• covered with putty;
• impregnated with primer.

Glue paper wallpaper without preparation Can be used on concrete or drywall. And foam plastic will not withstand the load. This material is not strong enough.

Instructions for gluing walls with your own hands

You can glue two-layer paper wallpaper joint to joint, if this method is provided by the manufacturer. The pattern adjustment is done dry on the floor. The technology assumes that the stripes are smeared first, and then the wall. Step-by-step instruction consists of four stages.

Stage 1: diagram and marking of walls

So that the first strip is oriented vertically, towards the surface wall panel line is drawn. Its location is determined using a plumb line, laser level or level. The wall can be completely marked, which will allow you to determine the required number of strips of wallpaper.

Stage 2: preparing wallpaper

Having measured the height of the ceiling, we begin to prepare paper sheets.

Stage 3: gluing

Stage 4: final

How to glue in problem areas?

In the process you will have to glue paper wallpaper in hard to reach places. Each case is different and has a number of features. To seal areas under the window, above the doorway, behind the radiators, you need to measure and prepare the strips in advance the right size. Difficulties also arise if the room uneven walls, as well as when gluing internal and external corners.

The photo shows a diagram of gluing wallpaper around sockets and switches:

The photo shows a diagram of wallpapering behind the radiator:

Step-by-step guide to covering a ceiling

Basically the technology is identical. Is it better to glue paper wallpaper to the ceiling away from the window? It matters how the strips are glued (overlapping or butt to butt). The rest of the sequence of actions is the same.

Video instruction

For greater clarity, it is better to watch a video that describes and shows full cycle works

How long does it take for paper wallpaper to dry?

On average it is 8-20 hours. Single layer ones dry faster. At this time, there should be no drafts in the room. Drying time depends on air temperature. In unheated rooms this period can be doubled. It is prohibited to speed up the process with fans, heaters, or hair dryers.

To ensure that paper wallpaper lasts a long time and is strong, it is better to give it some time. If you adhere to the presented rules and recommendations, the renovation will please the eye for many years.