Today, paper wallpapers are still the bestsellers due to their undeniable advantages. They are environmentally friendly, so they allow the walls to breathe and do not emit unpleasant odors. The existing huge selection of various colors and the low cost of this material can satisfy the taste of the most demanding customer.

Knowing how to correctly paper, any lazy owner can quite cope with this task without resorting to the help of professionals. It will become even easier to do this if you take into account some of the builders' advice on how to do the job correctly so that you can admire the papered walls for a long time.

Preparing the walls

The quality of wallpapering largely depends on how meticulously prepared the surface of the wall. First you need to remove all old coatings. First, they are peeled off dry, and what remains must be moistened with water and scraped off with a spatula.

It is better to wet the wallpaper with a natural bristle brush. The paper surface is slightly damaged, which makes it easier to absorb water. It makes no sense to buy the advertised special gels and solutions for this purpose. As practice shows, the result from them is no more than from ordinary warm water. You need to remove old wallpaper very carefully, all without a trace. Otherwise, when applying a new coating, the remaining pieces move away from the wall, forming bubbles. The remnants of wallpaper from the floor must be removed immediately, before they have time to dry.

After cleaning the wall, you need to carefully putty all the irregularities and cracks.

How to cut the wallpaper correctly

It is very important to properly cut them (cut). If they do not require the selection of a pattern, then the strips of the required length are simply unwound from the roll and cut. This should be done face down, leaving a small allowance for trimming. If the wallpaper has a pattern, it is necessary to select the adjacent stripes so that the pattern on them coincides. It is very important to unwind the roll in the same direction. The surface to be cut must be clean and level.

Holding on to the cut, you need to push the roll, unwinding the web to the desired length. Then measure the exact length with a tape measure and mark with a pencil. After that, you should bend the strip, combining the sides and smoothing the bend, along which the incision is made in the future. It is imperative to fold the canvases with the pattern down. So that the wallpaper does not deform under its own weight, the number of stripes in a stack should not be more than ten pieces.

Glue application

The adhesive is selected accordingly. Usually, the recommended adhesive is indicated on the gluing instructions. For a heavy coating, for example, a special composition is required, designed specifically for this type of material.

How to properly glue paper wallpapers so that you do not have to re-glue them later? It is very important here to properly prepare the adhesive. Dry glue is diluted in water at room temperature. To do this, in a plastic bucket or basin, you need to create a whirlpool with a brush on a long handle and gradually pour the glue into the resulting funnel, without ceasing to thoroughly mix.

Diluting the adhesive in cold water can lead to lumps. And too warm water will affect the quality of the glue, besides, the wallpaper, when applied with a warm composition, can get wet and creep along the seams after drying.

If the base of the wallpaper is paper, then the glue should be applied directly to the canvas, leaving it for a while to allow it to soak. The swelling time depends on the thickness of the wallpaper and is usually indicated on the packaging. The denser varieties take longer to soak. Experienced craftsmen know how to properly glue paper wallpapers: this always requires very great care, since such wallpapers do not differ in strength and durability. At the slightest careless movement, they can break.

It is much easier to glue non-woven fabrics in this case, they are applied not to the canvas, but directly to the wall. To do this, you can use a roller or a wide brush.

How to glue paper wallpaper

It is recommended to start gluing wallpaper from the corner closest to the window. Moreover, this should not be done from the very corner. At the beginning, at a short distance from it, using a level and a ruler, draw a vertical strip with a pencil along the entire wall. It is from this line that the pasting should begin. What is the best way to glue paper wallpapers? It is much more convenient to do this together, when one on a stepladder aligns the upper part of the canvas, and the second makes sure that the edge of the strip is aligned with the drawn vertical line. If glue accidentally gets on the front side of the wallpaper, wipe it off immediately with a dry soft cloth.

It is recommended to remove the skirting board before pasting the walls, if possible. Many people know how to glue paper wallpaper correctly. However, the presence of sockets and switches on the wall can create certain difficulties. Before starting work, such elements must be removed, while not forgetting to de-energize the room. The wallpaper is glued directly to the socket hole, and then a neat cut is made in this place. When the work is finished, the sockets and switches are reinstalled.

Features of gluing duplex wallpaper

Duplex wallpaper belongs to the category of heavy, therefore, they require the use of a specialized glue designed specifically for such a coating. They consist of several paper layers and are covered with a special compound on top that protects them from the destructive effects of the external environment. Such wallpaper can be used even in rooms with high humidity. Having a fairly large thickness, they can perfectly hide all the irregularities and imperfections in the surface of the wall. Often the canvas has to be soaked with glue for a long time before being glued to the wall.

There are no special recommendations on how to properly glue duplex paper wallpaper. The principle of pasting remains the same. The cloth, smeared with glue, is applied with its upper end to the wall, its edge is leveled along the drawn vertical line, after which it is carefully ironed with a roller or dry cloth. Ironing movements should be done in the direction from the center to the edge of the strip, achieving tight adhesion and the absence of air bubbles.

Embossed wallpaper has a relief pattern, which is created using special rollers with high pressure on the paper. Due to this texture, it is easy to hide all the roughness and unevenness of the wall. Since the embossed wallpaper is also heavy, you will need a special glue to glue it, into which you can add more PVA during dilution for reliability.

Foamed wallpaper

Such wallpapers are a kind of vinyl and are made by screen printing. They have a slightly rough, shiny surface, perfectly hide irregularities, do not stretch. There are some peculiarities of how to glue paper foamed wallpaper. Such wallpapers adhere perfectly to any surface, be it plaster or paint. The only exception is a wall covered with lime or whitewash. Only the specialized glue recommended by the manufacturer should be used. Foamed wallpaper is not able to pass moisture, therefore, in order to prevent the appearance of mold, the wall surface should be treated with an anti-fungal impregnation.

Wallpaper gluing end-to-end

This method is the most common, but not everyone knows how to glue paper wallpaper back to back correctly. To do this, you must follow a number of important rules. You should start from the corner of the wall on which the window is located. The first strip should be oriented not at an angle, which may turn out to be a curve, but at a plumb line or level. Wallpapers can have different characteristics, this must be taken into account. Each next canvas is located parallel to the previous one so that the edges touch as closely as possible.

In this case, you should not immediately glue the strip tightly so that it is possible to correct it in one direction or another. The edges of the strip should be very well coated with glue. The vertical line must be checked after applying every other strip.

You can learn from experts how to properly glue paper wallpaper, but you can only learn how to do this flawlessly by experience.

And finally, a few rules that will help to avoid various unpleasant situations when pasting walls. Before carrying out work, you must turn off the electricity. The windows must be tightly closed to exclude any drafts. The room being renovated must be warm and dry.

When renovating their apartment, novice craftsmen think that wallpapering is a common thing, and everyone can cope with it. But we dare to disappoint you, high-quality and professional wallpapering has many stages, which we will talk about in our article.

How to glue paper wallpaper - preparing the room

Before you start working with wallpaper, you need to clean the walls from the previous coating. If you had vinyl wallpaper, first remove the top layer with a spatula, and then you can peel off the remnants. When the wallpaper was glued with an overlap, the joints are evenly cut and sanded.

• If the wall has bumps and cracks, level the unevenness with putty or plaster. At the end of the work, go through the primer, then the new wallpaper will lay down smoothly and beautifully.
• If the previous coating was glass wallpaper - rinse the wall with a solvent, then putty and priming the common surface.
• To remove textile wallpaper, you need to treat the wall with a universal wallpaper remover. As a rule, this type of problem does not arise, and you can easily remove them manually without resorting to various tricks.
• When you decide to apply the wallpaper, where there used to be paint, you need to remove the paint with a special solution. Then scrape off the wet paint with a spatula, and put the rest of the putty in an even layer.
• Walls made of fiberboard, chipboard and drywall are pre-primed and sanded. Pay particular attention to board joints and screw and nail holes.

How to glue paper wallpaper - cut wallpaper

After you have prepared the wall for wallpapering, proceed to cut the roll. It is advisable to have an assistant in this matter.

• The first step is to check that the serial numbers of the wallpaper have the same values. Also look in the instructions for the wallpaper, how best to glue this type - in the joint or overlap.
• Measure the height of the wall with a tape measure, and mark the measurements with a pencil. Add 5-7 cm of stock to the measurements.
• Prepare a wallpaper knife and a metal ruler for easy cutting.
• Measure and cut 5 to 10 strips at a time.

How to glue paper wallpaper - dilute glue

The work is done by one person, without any difficulty. The main condition for getting a good result is following the rules without breaking the sequence. It is recommended to purchase the glue for light wallpaper, the usual preparation is as follows:

• Pour cold, clean water into a container. To dilute a medium pack of glue, you need about 5-7 liters of water.
• Stir gradually and pour out the glue.
• Stir the mixture well and leave to swell for 10-15 minutes.

The finished glue should not have a liquid consistency and lumps; to get rid of the latter, stir the glue by pressing the lumps.

How to glue paper wallpaper - we process it with glue

This type of wallpaper has a tendency to tear after glue gets on it, so all work should be done carefully and carefully.

• The wallpaper strip must be unrolled on a flat and clean surface - a table or a floor.
• It is recommended to apply the adhesive with a roller or a wide paint brush, taking care that there are no dry spots.
• To avoid getting glue on the front side, take the edge of the strip and fold it towards the middle, repeat the procedure from the other edge. Next, fold the canvas in half.
• Leave the strip on for 4-5 minutes to absorb the glue. During this time, glue the wall to the width of the wallpaper strip.

How to glue paper wallpaper - wallpaper gluing

• Begin to glue the wallpaper from the top line of the marking, gradually expanding along its entire length.
• Next, you need to smooth out the glued strip; for this purpose, use a dry cloth or rubber roller.
• Smoothing is carried out in the form of a Christmas tree - imagine that you are drawing a Christmas tree with a roller, moving from the middle to the edge, sketching each branch. With these movements, we get rid of air bubbles and level the surface.
• To glue the next canvas in a joint to the previous one - attach the strip as much as possible to the edge of the already pasted strip. Smooth the edges of the strips especially carefully at the joint and remove excess adhesive from the front side with a dry cloth.

After pasting the wallpaper, wait until it is completely dry, and only then proceed with unnecessary cutting. Cut off unnecessary edges with a utility knife.

There is a kind of test among the people. Before starting life together, a young couple is recommended to glue the wallpaper together. Of course, every family has its own method of gluing paper wallpaper, and it has been passed down from generation to generation.

But not everyone succeeds in sticking it, so that after that you do not have to finish something and redo it. Despite the seeming simplicity, this process has many nuances that you need to know.

Benefits of paper wallpaper

Despite the fact that today you can buy modern non-woven or vinyl wallpaper, the demand for old paper does not fall at all. This is due to a large number of positive features:

• Price. The cheapest rolls cost surprisingly little. The price range is very large, anyone can find embossed wallpaper at a suitable price.
• Range. The choice of patterns and colors is truly impressive. Some models are simply indistinguishable from expensive branded models.
• Suitable for rooms with humidity up to 60%.
• Environmental friendliness. Unlike other types, they are 100% environmentally friendly.
• Air circulation. The wallpaper is breathable without any problems and does not cause an allergic reaction. They can be safely glued in the children's room.

So that such paper canvases do not lose their appearance, do not allow direct exposure to sunlight or high humidity. On the other hand, even if this happened, you can re-glue it again, the main thing is to know how to glue paper wallpaper.

Some features of gluing

When choosing wallpaper, you need to understand that they come in different varieties, for example, from one layer and from two. The former, of course, are not very durable, but the latter are much stronger. This can be seen if you peel off the old duplex wallpaper.

The bottom layer or the layer that is in the base usually does not have any patterns and is intended to be glued to the wall. At the factory, it is bonded to the second outer layer. They can be plain or embossed.

To stick a simplex or single-layer wallpaper, you need to understand that the wall must be perfectly flat. Otherwise, a thin canvas will not be able to hide flaws, and in some cases, on the contrary, will expose them.

The positive thing is that they can be glued with an overlap. Some people even put them on old wallpapers, if they are in good condition, of course. As for the duplex, it is better to stick such a canvas end-to-end.

In general, it is better to consult a specialist in a hardware store before gluing paper wallpaper. They usually know exactly what kind of wallpaper and how to glue it, as well as how long it should sit with the spread glue.

Preparing the walls

Good preparation is at the heart of the success of any undertaking. The first step in updating a room is to remove all old wallpaper. Next, you need to carefully examine the entire surface for cracks and irregularities. All the bumps and pits must be aligned so that the base is a flat surface.

If duplex wallpaper can still hide some old small protrusions and irregularities, then thinner simplex wallpapers will not be able to do this. After completing work with the walls, you need to purchase some tool:

• glue and some kind of container for it, a bucket is better,
• good medium-sized roller,
• a wallpaper knife and sharp scissors just in case,
• wet sponge,
• get some newspapers, you can old ones,
• level,
• pencil and long ruler,
• two tassels - large and small,
• wallpaper spatula (plastic),
• if the walls are high, then you will need another ladder or stepladder.

The final stage of preparation is to remove everything unnecessary from the room, close the windows and the door so that there are no drafts. It is better to turn off the electrician. If the glue will be smeared on the floor, then it is worth spreading some old wallpaper, oilcloth, newspapers or something else.

You can clearly see how to prepare a wall for gluing paper wallpaper in the video:

Wall marking and wallpaper preparation

Before you start gluing the embossed wallpaper with an overlap, you should make sure once again that there is enough canvas. There should be one more roll, or even two. If the wall is the same in height along the entire perimeter, then you can immediately cut the required number of strips.

Important! It is always worth leaving an allowance of 10-15 cm on each side.

If the embossed wallpaper has a pronounced pattern, then you will have to pick it up and only then cut off the necessary strips. You need to be especially careful when gluing end-to-end.

In order for the first strip of the canvas to be perfectly vertical, you need to draw a vertical line on the wall exactly along the level at a distance from the corner equal to the width of the wallpaper. Experts recommend performing this step also in the case when thin wallpaper is glued, not only end-to-end, but also with an overlap.

The good old ones will help with this: a pencil, a ruler and a rope with a plumb line. Of course, if there is a laser level, then this greatly simplifies the process.

The actual gluing

Old wallpaper has been torn off, new embossed wallpapers have been bought, the walls are prepared, everything you need is there - you want it or not, but you need to glue it back to back or overlapping. If the room allows, then it is better to spread the strips and spread them calmly with glue.

It is necessary to soak the wallpaper well with the glue base, while this is happening, so that the smeared canvases do not interfere, they can be folded in half and removed to the side. As soon as time passes and the strips themselves are ready, you can start gluing the first one.

Advice! To make dense glue-based wallpaper soaked better, experts recommend slightly warming up the mixture and applying in two layers.

It is most convenient for someone to help, for example, a friend, parents or significant other, but you can do everything yourself. To make the process of gluing the wallpaper end-to-end more fun and without incident, you need to distribute responsibilities.

For example, one person will stand on a stepladder or stool and apply flat glue and iron them. Another should carefully feed the prepared canvases. It is important not to wrinkle the edges so that there are no difficulties when gluing end-to-end.

If the wallpaper is smooth, then it is very convenient to level it with a plastic spatula. Embossed wallpaper, the top layer of which is embossed, is unlikely to survive this. Therefore, it is better to level them with a roller.

You need to carry out in the direction from the middle to the edges. This is done in order to expel all air bubbles. If any remain, this can lead to deformation of the wallpaper, and it will not matter at all how they are glued, end-to-end or overlapped.

When smoothing along the edges, glue will periodically pop out. To remove it, it is enough to take an important sponge and gently run it along the glue base. Nothing should remain on the canvas.

Advice! If the wallpaper is very light, then this procedure should be carried out very carefully, and even better, put some paper for the printer.

Thanks to this, no marks or stains will remain in the overlapping or butt joints of the wallpaper.

If you want a beautifully pasted overlapping wallpaper at the base of the room, then experts recommend stopping periodically, moving away from the wall a couple of steps and looking closely at it. Thus, you can replace some flaws and fix them in time. When the glue-based canvas dries up, it will be too late to change anything.

To consolidate this all with an example, just watch the video:

How to glue in problem areas

Four smooth walls without windows, doors, corners and generally without anything is the dream of everyone who has glued wallpaper at least once. But, this does not happen and everyone will have to face places that cause certain difficulties, for example:

• all corners of the room,
• space behind the battery,
• sockets,
• openings above the doors.

Advice! So that in such places there are no difficulties, you need to remember one rule - you do not need to glue the entire strip of wallpaper to the corner. There, only a part is always used and glued end-to-end, if it does not work, then you can overlap.

In the case when the angle itself is perfectly even, then no difficulties should arise. The strip is cut in such a way that the grip on the next wall after the corner is no more than 1-2 cm. And then everything is as usual.

As for the battery, of course, the best option is to remove it. If it is not possible to do this, then you need to glue at least 10 cm deep on each side. Sometimes there is enough space to accommodate a large piece.

If it comes to the sockets, then you need to remember if they are de-energized, but it is better to go and check again. After that, you can safely remove the top cover and stick the canvas on top. Next, using a clerical knife, a hole is carefully cut out. Do not worry too much if the edge turns out to be uneven, all these shortcomings will be hidden by the lid.

If you want to decorate the wall with special borders, it is very important to wait until the wallpaper is completely dry. Depending on the adhesive base and the canvas itself, this process can take from 12 hours to 32. In most cases, specialists continue to work in exactly one day.

You need to remember well a few fairly simple tips that will help you avoid mistakes when gluing paper wallpaper back to back or overlapping. Better to try once than to suffer and redo it later.

To get a complete picture of how to glue paper wallpaper, you can watch the video:

And prepare strips according to it. Arrows on both sides of the vertical line at the same level (direct marking) indicate that the pattern must be drawn up. At different levels - they are glued in reverse order, when each next strip is directed in the opposite direction. An arrow on one side indicates that there is no need to adjust the pattern.

The list of other basic rules for pasting walls contains the following theses:

• All remnants of the previous coating are removed from the panels with a spatula, after which the surface is wetted, which is necessary for better adhesion.
• The glue is diluted according to the instructions or purchased ready-made.
• First, the strip begins to smear, and then the wall panel. The edges of the strip must be finished.
• They begin to apply from the top. In this case, the wallpaper is folded. You need to glue paper strips from the corner, placing them vertically with a plumb line or level.
• The fabric is smoothed with a rubber roller or dry cloth. To expel air and excess glue, this is done from the center to the edges.

The paper will shrink as it dries. So that no cracks appear, the stripes are glued with an overlap of 0.5 cm... Subsequently, when the paper dries, the wallpaper will shrink.

It is necessary to apply glue first on paper, so that during the time when they smear it on the wall, the paper wallpaper has time to soak. If you buy ready-made wallpaper glue, before gluing the paper wallpaper, mix it thoroughly, achieving a uniform consistency. The main thing is to choose the right composition in order to ensure a reliable bond.

Which wallpaper glue is suitable for paper wallpapers?

The correct choice of glue ensures that no yellow spots appear after drying, the paper wallpaper does not fall off, but when the time comes to change it, it will easily come off the wall. You need to choose based on the type of paper wallpaper, depending on whether it is a simplex or a duplex:

• Simplex. For thin paper single-layer wallpaper, formulations made on the basis of processed cellulose or cotton products are used. The versatile ones also fit.
• Duplex - double layer paper. Wallpaper is used for painting. They are heavy and thick, which requires the use of non-woven glue or CMC.

It can be glued to the composition for vinyl wallpaper. By adding PVA to it, they achieve greater adhesion strength. They also use busylate or pure PVA. All information about the mixing technology is on the packaging. If it is a special glue for paper wallpaper, this should be indicated.

What tools do you need?

To prepare in advance, you need to purchase and prepare:

• container for mixing the sticky mass;
• wide rubber roller;
• narrow roller and dry rags;
• a spatula for mixing glue;
• wallpaper knife and scissors;
• level or plumb line;
• pencil or ballpoint pen;
• brush with a wide butt.

After everything is at hand, they begin to prepare.

Correct preparation for gluing

After the glue has been prepared, everything needs to be ready. Otherwise it will have to be thrown away as it will set and become unusable.

The preparatory process is as follows:

• In order not to stain the floor covering, it is covered with plastic wrap. It is important to keep it clean.
• The electricity is cut off.
• Covers for sockets and light switches are dismantled.
• An adhesive composition is being prepared.
• If there is not enough light, the sockets are sealed with tape, which is then removed.

How to properly dilute the glue?

Before gluing the paper wallpaper, you need to cut it into strips and prepare the glue. The technology lies in the fact that the dry mixture is poured from the unpacked pack into a dry, clean, deep container. Water is also introduced there. In this case, you need to constantly stir until a thick, sticky mass is formed. The proportions are indicated on the packaging. It is enough to mix the ready-made mixtures.

IMPORTANT! Prepare enough glue to enough for 4-5 pages... Otherwise, the residue will thicken. Adding water to make it liquid again is prohibited. This mixture will not hold the wallpaper on the wall.

Surface preparation

It needs to be cleaned from the remnants of the old coating. It is impossible to glue paper wallpaper on whitewash and paint (oil or water-based). The surface must be free of dust. Old wallpaper is torn off, the remnants of glue are peeled off.

You can glue on the surface:

• covered with newspapers;
• covered with putty;
• impregnated with a primer.

Glue paper wallpaper without preparation possible on concrete or drywall... And the foam will not withstand the load. This material is not strong enough.

DIY wall sticking instructions

Two-layer paper wallpaper can be glued joint to joint, if this method is provided by the manufacturer. Fitting is done dry on the floor. The technology assumes that the stripes are first smeared, and then the wall. The step-by-step instruction consists of four steps.

Stage 1: scheme and wall markings

In order for the first strip to be oriented vertically, a line is drawn on the surface of the wall panel. Its location is determined using a plumb bob, laser level or level. The entire wall can be marked out to determine the required number of strips of wallpaper.

Stage 2: preparing wallpaper

Having measured the height of the ceiling, proceed to the preparation of paper canvases.

Stage 3: gluing

Stage 4: final

How to glue in problem areas?

In the process, you will have to glue paper wallpaper in hard-to-reach places. Each case is different and has a number of features. To glue the areas under the window, above the doorway, behind the batteries, it is necessary to measure and prepare strips of the required size in advance. Difficulties also arise if the room has uneven walls, as well as when pasting inside and outside corners.

In the photo, a diagram of gluing wallpaper around sockets and switches:

In the photo, the scheme for gluing wallpaper behind the radiator:

Step-by-step guide to gluing the ceiling

Basically, the technology is identical. Unless, it is better to glue paper wallpaper on the ceiling from the window. It matters how the strips are glued (overlap or butt-to-joint). Otherwise, the sequence of actions is the same.

Video instruction

For greater clarity, it is better to watch the video, which describes and shows the full cycle of work.

How long does paper wallpaper dry?

On average, it is 8-20 hours. Single layers dry faster. At this time, there should be no drafts in the room. Drying time depends on the air temperature. In cold rooms, this period can be doubled. It is prohibited to speed up the process with fans, heaters, hair dryers.

In order for the paper wallpaper to hold for a long time and firmly, it is better to give a margin of time. If you adhere to the presented rules and recommendations, the repair will delight the eye for many years.

Few people in our country have not tried it at least once wallpapering... Of course, you can hire a designer, a team of finishers and return to a house smelling of fresh renovation. Or you can survive the very search for the desired color, arguments with your spouse, children about the pattern and tone, pasting, which lasted almost until the morning, and the first rays of the sun playing on a piece of wallpaper that has lagged behind the wall ...

How glue paper wallpaper and get pleasure from it, we will find out today.

History of paper wallpaper

Paper wallpaper has been used by humans for decoration for many centuries in a row. For the first time, the Chinese began to paste over their home with rice paper. Later, the secret of making paper became available to the inhabitants of Japan. And around the 12th century, the question of "how to glue paper wallpaper" was also puzzled in Europe. Here they decided not to weave the pattern on the canvas, as on carpets, but to apply it to the finished surface.

And today, when the stores are full of vinyl, non-woven and other wallpapers, and fashion designers advise you to simply paint the walls, paper wallpaper do not go out of style or become less popular than they used to be. Why? The pros are obvious:

• Paper wallpapers are cheap and affordable for every pocket
• Pape the room with paper wallpaper, if desired and with some skill, anyone, even a teenager
• Paper wallpapers are easily glued indoors, where the humidity is less than 40-60%, that is, almost everywhere in the house
• Paper wallpapers are environmentally friendly, they are easily air-permeable, and have some sound-absorbing ability.

There are, of course, disadvantages - paper wallpapers are fragile, quickly fade in the sun and absorb odors.

Preparation for gluing paper wallpaper

There is nothing more difficult to repair than choosing a wallpaper, especially if you do it together with the other half. As a rule, tastes differ and a compromise is impossible, and therefore the question "how to properly glue paper wallpapers" sometimes freezes at the level of "how to choose them." In this case, try to take into account the recommendations of the designer:

1. Paper wallpapers are made in one layer, drawing a drawing from above, - simplex... The main plus here is the price and simplicity. A summer cottage option if you don't have a chalet or a villa outside the city. Wallpaper consisting of two layers - duplex- more reliable, they fade less and are lenient to a wet wipe in case of contamination.
2. A large pattern looks great in a voluminous room, but it will not fit into a small room at all. The same with a small drawing, only exactly the opposite - in a studio apartment, for example, it will simply get lost and merge into one canvas.
3. Dark rooms are "lightened" with pastel, warm wallpaper, and those facing the sunny side can be glued a little darker, adding a rich tone.
4. The interior should be in harmony with the wallpaper in the room, because the classic small flower will completely "kill" your high-tech headset. The textiles are also kept in tune with the general mood.
5. Shades of red are exciting, deep brown is depressing, turquoise is refreshing, yellow is uplifting, but if it is of a toxic acid shade, it causes irritation.

The next moment of preparation for gluing is cleaning the surface of the walls from old wallpaper, paint, putty and leveling, priming the walls. This stage is the most boring, tedious, but almost the most important - when paper wallpaper dry, all the irregularities will immediately catch your eye.

Often old wallpaper does not want to part with the wall. They need to be wet, wait a little and clean off with a spatula. Sometimes such wallpaper is ironed with a hot iron through a wet cloth, and ammonia or soda is added to the water.

Before gluing the wallpaper, you need to turn off the electricity in the dashboard and remove the covers from the switches and sockets. We apply the canvas to the wall and make a cross-shaped incision at the place of the outlet. So the paper strip will stick to the wall much better, and bend the corners and, if necessary, cut a little.

If it is possible to remove the old skirting board, it is better to do this, and after gluing the wallpaper, replace it with a new one. In this case, the bottom of the wall will look perfect.

What glue to glue paper wallpaper

What is good about paper wallpaper is its susceptibility to glue. There are few brands that these wallpapers will not succumb to. You can put paper wallpaper on non-woven glue - it won't fall off! If there is no glue or it has run out, but for some reason it is impossible to get into the store, you can glue the wallpaper with homemade paste: pour flour into the water, stir and bring to a boil. Remove immediately, mix, cool slightly. Thicker wallpaper sticks better with warm paste.

However, if there is a special glue for paper wallpaper the price of which suits us, we will use it. Most often they use glue for paper wallpaper - CMC. Sold in powder form. If not left in a humid room, it will not deteriorate for a long time. Pour the glue with warm water and mix thoroughly. Then it is left in the room where the wallpaper will be glued, for 10-12 hours, until it is completely dissolved. Stir occasionally. Initially we pour a little water, but later we add it to the state of jelly, while constantly stirring.

Glue "Bustilat" and "Gumilax" are also suitable for paper wallpaper. The preparation is about the same as the CMC, but it is also worth reading the instructions on the box before work.

How to glue paper wallpaper

Even in the store, you took into account all the signs, letters and numbers on the rolls of wallpaper and now, having opened it before gluing, you see that they are the same in tone. The paper wallpaper is accompanied by an edging. Sometimes it goes only from one side, and sometimes from both. If the wallpaper is thin, then you can overlap, then we cut off the edge only on one side. If they are tight, this seam will become noticeable, therefore we cut off both edges and glue back to back. We are very attentive to the window: we glue it from the window, on the right side, and cut it off on the right too. And then it is more convenient to remove the edge from the left.

Cutting and trimming is a very important stage. We measure the height of the space that we will glue, adding a little "to the stock". If the drawing is small, this "stock" will be enough for 10 cm, but for a large one it is worth adding all 30. Sometimes the floors and ceilings in apartments are so crooked that only a horizontal curb can correct the situation. In accordance with the first strip, we cut the second, with the second we level the third and further. It is very important not to confuse the direction of the wallpaper when cutting, it is especially easy to make a mistake if it is a floral pattern.

Regular scissors are completely unsuitable for cutting wallpaper - the edge may turn out to be uneven. We pick up a special wallpaper knife, measure a straight line by level or with a ruler with a triangle, mark it with a pencil, bend it exactly according to the marking and cut it.

The remaining scraps must be rolled up and removed, as they will be useful for small areas near windows, doors, and later for minor "patch" repairs, especially if children are growing up in the apartment.

Before gluing the first panel, a vertical line is marked on the wall. To do this, you can use plumb line, rubbed with chalk, or better - laser level. All subsequent canvases must be glued strictly vertically. We begin to glue the wallpaper from the window. Mark a vertical line on each wall.

It is especially difficult to glue the corner: we cut off the wallpaper in such a way that the overlap on the other wall at the widest point (our apartments usually have almost no even corners) is no more than 3-5 cm. ... The next strip is glued immediately from the corner along the newly exposed vertical line.

The wallpaper will lay on the wall evenly, without bubbles, and will not fall off, if you first smear the wall with glue at the distance of the strip, apply the glue on the strip evenly and, applying the wallpaper to the wall, go from top to bottom along the strip with a rubber roller or a soft clean cloth, smoothing every centimeter and expelling air from the middle of the panel to the edges. If the need arises, we smear the edges with a thin brush and re-pass it with a roller or napkin.

The glue that appears on the front side of the wallpaper must be immediately removed with a damp sponge, otherwise it will appear ugly on the wallpaper after drying.

Thick paper wallpaper should be rolled into twos after spreading it with glue and wait five minutes until it gets soaked. Thin wallpaper is glued immediately.

Wallpapering is more a collective affair than an individual one. Of course, one person with experience and skill will be able to paste over a room, but together it is much easier to do this. And if you allow children to spread glue on a wall or canvas, hard work will turn into family happiness!

In order for the wallpaper to dry faster and remain on the wall, hugging it tightly, it is necessary to exclude the slightest possibility of a draft. It is also better not to use an electric heater so that it dries naturally.

If a paper border was planned, you can glue it only when the wallpaper is completely dry.

Sometimes a nuisance happens, and new wallpapers are torn. This place can be sealed by picking up the pattern and using a sharp knife to cut out of the patch exactly the piece that will be inserted into the damaged place. When the wallpaper is dry, you will not find trouble if everything is done carefully.

Let's summarize our conversation on how to glue paper wallpaper videos by watching and noting for ourselves the nuances of future repairs: