In this article we will look at methods for attaching suspended ceilings of the three most popular designs:

• plasterboard;
• PVC panels;
• rack and pinion

The CD profile is mounted in two ways. The first involves creating a square one in 60 cm increments over the entire ceiling area. The second one requires installing a profile in increments of 40 cm, but only along the length of the drywall sheets. In this case, the frame will be more economical, since a smaller amount of profile is needed to create it.

After fixing the frame, the plasterboard is hemmed to it with self-tapping screws. The seams between adjacent elements are reinforced with reinforcing mesh or serpyanka. All irregularities, as well as holes for self-tapping screws, are puttied in at least two passes. Before subsequent finishing (painting or wallpapering), the surface of the sheets is primed.

The frame itself is fixed to the concrete floor using 60*4 mm screws and plastic dowels. In this case, it is worth excluding the use of wooden choppers, since they can change their size with changes in humidity. If the ceiling is wooden, then the frame is secured using ordinary self-tapping screws with a length of 50 to 100 mm.

If you want to do multi-tiered structure, then the ceiling levels located below are hemmed to the profiles of the upper tier. But don't even think about fixing the bottom tier to drywall. Over time, such a ceiling will simply collapse.

Useful little things

The design of suspended ceilings made of plasterboard and galvanized profiles is not complicated and therefore you do not need special knowledge to install it. But still, during the work some nuances should be taken into account.

It takes from 60 to 100 screws to fix one sheet of plasterboard. On straight sections, the step between fastenings can be 25 cm, on curved sections - 15 cm.

The edges of adjacent sheets are always fixed to one profile. If this is impossible to do, then you can do the following. First, one sheet is hemmed to the profile. Then the profile is hemmed to its edge so that half of its width protrudes beyond the edge of the drywall sheet. After this, the next sheet of material is hemmed to this protrusion.

The seams must be reinforced. Otherwise, you will experience cracks in the ceiling. If you don’t have serpyanka or reinforcing mesh on hand, you can get by with regular paper tape.

In order to obtain a curved surface of a large radius, a sheet of drywall is moistened with water. For small radius bends, the cardboard on the reverse (outer) side of the bend is cut or pierced with a special perforating roller.

In order to get a multi-tiered ceiling, it is not at all necessary to install a second-level frame. To do this, simply hem it to the main level next row sheets of plasterboard, cut to in the required form. Of course, such a tier is attached to the profile, and not directly to the sheets of plasterboard of the first level.

PVC panels

The next type of suspended structure that we want to consider is PVC panels. This ceiling is made independently using wall plastic panels(more details: " ").

Compared to drywall, the material does not offer many possibilities, but at the same time it is very cheap and easy to install. Often such ceilings are installed in damp rooms, that is, in bathrooms and toilets.

Installation diagram

First let's look at wooden houses, since the method of fastening in them differs from other types of buildings. The most in a simple way For the ceiling lining, the panels will be fastened to a sheathing made of timber with a cross-section of 30*30 mm. Of course, this method is only suitable for dry rooms.

If height ceiling beams is large enough, then the sheathing can be not assembled, but the panels can be hemmed directly to the beams. The step between fastenings should not exceed 50 cm, the recommended step is 40 cm. If the cells are fastened less frequently, the panels may sag over time.

How to fix a suspended ceiling in an ordinary city apartment with concrete floor?

• In rooms with constant temperature and low level humidity can be mounted wooden sheathing. The timber is hemmed directly to the ceiling, with a fastening step of 40 cm. In this case, the frame is placed perpendicular to the direction of the panels without the use of additional hangers. Minor differences in the height of the main ceiling can be compensated by placing a gasket of appropriate thickness under the block. The horizon of the sheathing is checked with a level. It is recommended to process wooden elements antiseptic, then the ceiling is guaranteed to last for many years, not succumbing to deformation and rotting.
• For rooms with high humidity or unstable temperatures best mount for PVC panels there will be a galvanized profile. The principles of its installation are almost the same as the design used for gypsum boards. A UD profile is installed around the perimeter of the room (read: ""). The CD profile is mounted perpendicular to the panels. The fixation step is 40-50 cm. In this case, the profile can be attached both to the ceiling itself and to hangers.

Useful little things

To fix the frame, plastic dowels and 60*4 mm screws are used. If you need to secure a large section of the ceiling to a small number of hangers, then it is better to replace the screws with anchors. In this way, greater reliability of fastening can be achieved.

PVC ceiling edged with both a special profile and the most ordinary plinth. Moreover, in the case of baguettes, you should not have any difficulties with fixing the last panel. It is simply fastened with screws, and the fastening points are covered with a plinth.

Slat ceiling

Another equally popular way to create suspended ceilings is the use of aluminum slats. The suspended ceiling is fastened to factory traverses, which cannot be replaced by timber or profiles.

What, then, is such a ceiling good for if it does not allow the use of other types of frames and costs significantly more than the systems listed above?

The material of the slats is aluminum. It is not afraid of corrosion even in conditions of high humidity. Over time, the panels do not change their physical properties.

Suspended ceiling fasteners are aluminum profiles or galvanized steel construction. The service life is almost unlimited. At the same time, throughout its use, you are unlikely to encounter a situation requiring surface repair.

Aluminum slats are not afraid of flooding by neighbors above. It will be enough to wipe the ceiling surface with a sponge and detergent.

Installation diagram

How to fix such a ceiling? The work steps resemble the assembly procedure of the previous two types of suspended structures. Guide rails are attached along the perimeter of the wall, which will also hide the edges of the panels. Traverses are hung on the suspended ceiling mount, which are aligned strictly horizontally. It is to them that the slats are attached. The type of suspensions themselves largely depends on the distance to the base ceiling and the material of the traverses. Therefore, the same direct hangers that are used for the ceiling frame made of gypsum plasterboard can be used here.

But often the aluminum ceiling is hung on special spring hangers, which long distance before overlap they are installed on springs. The free ends of such knitting needles are bent for greater reliability of fastening.

How to attach slats to traverses? To do this, they are simply inserted into place and snapped into place. At the walls, ceiling elements are cut both in length and width.

If you use perforated slats, then in this case there is no need to remove ventilation duct below ceiling level. But such a solution is unacceptable for kitchens with gas stoves.

Slatted ceilings will be great solution for bathrooms, toilets and kitchens. But for the bedroom and living room it is better to choose a different type of hanging structure. This is where cleanliness comes into play. aesthetic side. Although some caveats may be made here. For a living room interior designed in a high-tech style, an aluminum slatted ceiling with a mirror surface can be an ideal option.

Installation of a suspended ceiling, detailed in the video:

Conclusion

You can read more about each type of suspended ceiling on the pages of our website. There you will also find photos of certain constructive and design solutions. And remember that we have reviewed only a small part of the suspension systems available on the market today. Each of them has its own advantages and disadvantages. Therefore, the most important point when installing ceilings is right choice appropriate design.

We hope that this article helped you understand how a suspended ceiling is attached. We wish you success in your renovation.

To get a suspended ceiling, you first need to install a frame onto which the main decorative elements are already attached. Depending on their type, the installation scheme of the guide elements is selected. The frame also consists of moldings, which are installed at the corners, and hangers, which are responsible for adjusting the structure in height. The latter can take the form of brackets, metal rods or ordinary wire. Installation is carried out along the installed guides decorative elements. If used plasterboard sheets, then it is mandatory to putty and paint them.

Where to order the installation of a suspended ceiling in Moscow?

Our company is engaged in the installation of suspended ceilings of varying complexity in Moscow. We guarantee high quality of work performed, regardless of the materials used, design solutions, contour or purpose of the room. Installed ceiling will not only be durable, but will also fully perform the necessary functions. High quality is ensured by step-by-step control of work performance, using only professional equipment and tools, extensive experience in this field. We also always take into account the customer’s requirements, and if necessary, provide advice on all issues of interest.

A suspended ceiling is a structure that is attached to base surface, but is located at a distance from it. This type of finishing is very popular, as it does not require leveling the main ceiling. Designs developed different types, from them you can create complex multi-level or standard flat surfaces. It is thanks to the variability and perfection of the finished ceiling that suspended systems are used very often. Install simple designs you can do it yourself.

Design suspended ceiling consists of a frame and casing. The base, as a rule, is metal, it holds all the finishing. Sheathing can be made of different types of materials: slabs, plasterboard sheets, PVC panels, slats.

Advantages of hanging structures:

• There is no need to level and repair the base;
• You can hide protruding communications and beams;
• The suspended ceiling provides additional sound and heat insulation;
• This finish does not require repair for a long time;
• Designs can be given an unusual complex shape Thus, zone the room or visually change the proportions of the space.

The cost of finishing with suspended structures is slightly higher than plastering and painting the base ceiling, but the investment will quickly pay for itself, since repairs will be required in at least ten years.

Preparing the base surface for installation of a suspended ceiling

In this case, alignment is not required. The only thing that needs to be done is to check the reliability of the base ceiling, its strength and ability to support a heavy structure.

If there are damaged areas of plaster on the ceiling or peeling paint, then the surface must be cleaned so that fallen pieces do not clog the space between the base and the finish.

It is necessary to install electrical wiring lines in advance, mark the location of lamps, ventilation, fire protection system, video surveillance and other communications.

One of the most important stages work - determining the level of installation of a new ceiling. A hydraulic level will help you cope with this work. How to use it, watch the video.

Suspended plasterboard ceiling

Plasterboard structures can be given any complex shape. It is this material that is given preference in the construction multi-level ceilings. The frame for such structures is made from special profiles. There are two main types: ceiling guide (it is attached along the perimeter of the walls) and rack ceiling (connects guide elements and creates a plane for attaching plasterboard sheets). To fix the racks to the base ceiling, special elements with perforations for self-tapping screws are used - hangers.

To make a curved frame, you can use a special arched profile or make notches on the sides of the rack profile and give the desired bend.

To create corners, you need to make V-shaped cuts in the sides of the rack profile and bend them to the desired degree.

How to make a frame:

Next, you need to cover the resulting frame with sheets of plasterboard. To do this, you need to measure the area on the ceiling, cut off the required fragment from the plasterboard and secure it with self-tapping screws on the guide and rack profile.

To make an even cut, you need to mark a sheet of drywall with a pencil, attach a rule or a long ruler to it and cut it upper layer stationery knife. Then bend the sheet so that the gypsum filler bursts along the intended line, and cut the second sheet of cardboard.

The plasterboard box needs additional finishing. First it must be primed, then the joint lines of the sheets, screw heads and corner connections. Next, the surface can be painted with enamel, water-based or oil paint.

Suspended ceiling made of PVC panels

Most a budget option suspended ceiling finishing – PVC panels. They do not require additional finishing or repairs during operation. Plastic can withstand high humidity and low temperatures well, so this type of finish can be used in the bathroom, on the balcony or veranda. Panel structures are very easy to clean - any dirt can be removed from them with a damp cloth. The width of standard parts is 25 and 50 cm.

The panels are equipped with grooves into which each subsequent sheet is installed and hides the place where the previous one is attached to the frame. This ensures not only ease of installation, but also tightness and durability of the finish.

To make a frame you can use metal profiles for drywall or wooden beam. The sheathing pitch should be no more than 50 cm. The panels are very light, so only perpendicular posts are enough.

Don't forget about fire safety. Electrical wiring lines under the ceiling made of PVC panels must be hidden inside the corrugation.

The kit for installing a suspended ceiling consists of a U-shaped guide plastic profile and the panels themselves. The guide elements need to be installed around the perimeter of the room; the ends of the panels will be installed in them.

Panel installation:

At the final stage, a decorative plinth is installed. You need to glue it on liquid nails. Apply glue only to the side that will be adjacent to the wall.

Armstrong type suspended ceiling

Armstrong ceilings consist of a suspended base and slabs. The frame remains partially open during installation, so its visible parts are given an attractive appearance. The materials for making plates can be: pressed mineral fiber, glass, plastic. The convenience of this design lies in free access to communications hidden under the ceiling.

The frame structure, made of load-bearing and transverse profiles, is supported by spring hangers, which are easily adjusted in level. Instead of spotlights or chandeliers for Armstrong, it is advisable to use special built-in lamps, which are selected according to the size of the cells and plates.

Armstrong ceiling installation:

During installation mineral slabs Clean gloves must be used in the cells. This is due to two reasons: the surface of the parts gets dirty easily, and mineral fiber can be irritating to the skin.

Slat ceilings

The slatted ceiling design consists of narrow and long panels and hanging frame. Reiki are made from metal and plastic. The frame is assembled from adjustable hangers and universal support rails. Along the walls, the structure is held in place by guide angles. The panels are fixed to the rail with special latches, so no additional fasteners are required.

Reiki are presented in a huge assortment. You can choose elements of different shades, materials and textures that will harmoniously complement the interior of the room. There are two types of rail fastening possible:

Ceiling installation is carried out in several stages:

At the final stage you need to install decorative profile, if used open system fasten the slats, and glue the baseboard around the perimeter.

The choice of design and materials for a suspended ceiling depends on many factors. If the installation is done by hand, then its complexity matters. Play a big role performance characteristics material. For rooms with high humidity And low temperatures it is necessary to select a material that is resistant to these influences. The difficulty of maintaining the structure also matters; for example, in the kitchen it is better to install a ceiling made of plastic, metal or glass. It will be difficult to remove grease and fumes from the painted surface of drywall.

Armstrong ceiling systems are known as prefabricated suspended structures consisting of metal frames and mineral fiber boards. You can easily hide communications under them and they will not spoil the appearance of a room decorated in a classic style.

Advantages and disadvantages

Most often, Armstrong ceilings are installed in public institutions, when decorating offices, retail establishments, cafes, and they also fit well into the decor of apartments.

Among the advantages of these ceiling structures are:

• low cost;
• no need for preliminary preparation base base;
• sufficient degree of sound and heat insulation;
• a wide variety of slabs allows you to implement any design solution;
• simple installation of Armstrong suspended ceiling, which does not require the participation of professionals;
• the ability to make communications and ventilation systems invisible;
• providing easy access to the ceiling space for inspection and repair;
• trouble-free installation of lighting devices;
• it is possible to dismantle and reuse elements of the system, since it is completely dismountable.

Armstrong has few disadvantages:

• it lowers the height of the room by no less than 20 centimeters, so using it in apartments is not always possible;
• the ceiling cannot be installed in a room with a non-standard configuration;
• the design will not protect furnishings in the event of a leak from above;
• it does not tolerate high moisture, from which organic slabs begin to get wet and undergo deformation.

The popularity of such ceiling systems, due to their numerous advantages, does not decrease. It is quite simple to install the Armstrong ceiling yourself, both in the office and in a residential area.

Features of the structural device

Armstrong ceilings consist of a frame made of metal slats assembled in the form of cells measuring 60x60 centimeters. Soft or hard tiles of a certain size are laid on them.

Rigid elements are made from the following materials:

• whole or perforated sheets of metal;
• tree;
• plastic;
• mirror;
• glass.

Soft boards are made from organic or mineral materials. IN Lately due to the fact that preference is given to environmentally friendly finishing materials, mineral products have become used very rarely, since they contain mineral wool, the smallest particles of which, upon penetration into the respiratory system, cause serious harm to human health.

To install an Armstrong-type suspended ceiling, soft organic tile elements are often used. They contain recycled cellulose raw materials, so they are completely safe, weigh little and are easy to cut if necessary.

To build the frame and finish it you will need:

1. Ceiling tiles with dimensions of 60x60 centimeters.
2. The supporting profile is T-shaped, 370 centimeters long. It is installed parallel to the short side of the room and, if necessary, extended using standard fasteners or the excess part is cut off.
3. The transverse T-shaped profile is 60 centimeters long.
4. Longitudinal T-shaped profile 120 centimeters long. It is attached to the supporting profile with an interval of 60 centimeters.
5. Ceiling suspension with hook and rod. The rod is attached to the ceiling with dowels or anchors, and the hook is attached to the supporting profile. The length of the suspension is adjusted with a clamp and thereby ensures a horizontal position of the frame.
6. L-shaped wall profile 300 centimeters long. It is installed along the perimeter of the room using a level.
7. Dowel or anchor. When the Armstrong ceiling is attached, these products serve to fix the suspension to the rough base.
8. A cut ceiling slab designed to fit the parameters of the room.

The profile for assembling the frame can be metal-plastic or metal, coated with a powder coloring composition. The standard width of its shelves is 15 or 24 millimeters. In the first case, the profile is used for the construction of lightweight structures using organic tiles.

The second option is used in the construction of metal, glass, mirror ceiling structures with a large number built-in elements. For fastening Armstrong to the ceiling, if it has heavy weight, use reinforced suspensions.

The frame is fixed using standard fasteners; as a rule, it requires minimal adjustment, since it is assembled in the same way as a designer, quickly and simply.

By the way, if you wish, you can make tiles for Armstrong yourself from MDF or wood panels. Their design gives the interior a unique style.

Calculation of components

Before installing the Armstrong ceiling, you should calculate the materials that will be required for the work, for which you measure the length and width of the room. Taking these parameters into account, their number is determined.

When heavy lamps or ventilation system elements are to be installed, experts recommend additionally using hangers. All necessary materials It is advisable to order with a small margin, since adjustments may be required during the work or the product may be damaged.

Preparing the base

As with the installation of other types of ceiling structures, before installing the Armstrong ceiling, a number of preparatory measures are carried out. This suspension system makes the condition of the rough foundation completely invisible.

The preparatory stage consists of removing the old one that has become unusable finishing material. When paint or whitewash adheres firmly to the surface of the ceiling, it is permissible not to remove it.

If areas of the finish peel off or a layer of plaster falls off, they can damage the installed tiles. For this reason, they must be removed and the cracks filled with putty. Before installing Armstrong ceilings in a room where there is a high probability of leaks, the rough base should be waterproofed.

Since there will be a gap of 20 to 25 centimeters between the ceiling and the surface of the structure being installed, heat and sound insulation materials can be placed in it. Before placing them, first of all, for the fiber boards of the heat insulator, a sheathing is assembled from wooden blocks, positioning it in such a way that it is slightly offset in relation to the suspended frame.

Step-by-step assembly of the Armstrong ceiling

When starting work, you need to use the instructions for installing the Armstrong ceiling.

Installation is carried out in several stages:

• Marking the level of the structure. The successful outcome of the entire work largely depends on the correct execution of this stage. To carry out markings use laser level. It starts from the lowest of the four corners of the room. It is laid aside from the ceiling average length suspension so that it can be adjusted in the direction - both up and down. Level from this point, lines are drawn along both walls, the corners adjacent to them are marked, and then the lines are continued on all other walls. At the last corner the lines should meet.
• Fastening wall profiles. When installing L-shaped elements, dowels and screws or anchor bolts are used at intervals of 50 centimeters down the shelf and aligned according to the previously marked line. The profile is bent at the corners, first cutting the shelf.

• Installation of ceiling suspensions. These frame elements serve to attach the supporting profile. To place ceiling hangers in the required location, you should map out the location of the slats in advance. They are installed parallel to the short wall of the room in increments of 120 centimeters. For convenient installation, you can draw corresponding lines on the ceiling or use a chalk cord for marking. Next, according to the diagram, they mark the places where the suspensions are attached. In accordance with the installation instructions for Armstrong suspended ceilings, these components should be located at a distance of no more than 120 centimeters from one another and 60 centimeters from any wall. They are secured with anchor bolts or dowels. To do this, drill holes according to the markings and fix the suspension to the eye of the rod.
• Installation of suspensions for lighting fixtures. The places where the installation of lamps and split system units is planned must be additionally reinforced with suspensions, placing them with a slight offset relative to the main components of the frame. The hanger hook often interferes with the installation of elements, so it is advisable to place the hanger with an offset of 5 - 10 centimeters.
• Installation load-bearing profiles . They are placed according to pre-applied markings and secured using hanger hooks to the holes in the profile. It is necessary that the ends of the support rails rest against the L-shaped shelf. When the length is not enough, it needs to be increased by using a standard lock located at one of the ends of the rail. If necessary, the profile can be trimmed. Read also: "How to assemble the Armstrong ceiling - installation sequence."

• Alignment. It is necessary to achieve a horizontal arrangement of the load-bearing elements by adjusting the length of the hangers. To do this, first compress the butterfly clamp and move the hook and rod in the required direction. Then the clamp is released and thereby fixes the length of the suspension. To control the ceiling plane, use a level and tightly stretched cords.
• Assembling the structure frame using profiles of transverse and longitudinal types. Longitudinal profiles having a length of 120 centimeters are installed between load-bearing elements in increments of 60 centimeters using fasteners on the profile. To avoid cutting the edge slabs again, you should adjust the distances from the walls, making them symmetrical. Transverse products 60 centimeters long are mounted in the gap between the longitudinal slats using conventional fasteners.
• Installation of built-in elements. As indicated in the Armstrong ceiling installation instructions, after completing the frame assembly, you should begin filling the cells with slabs and installing built-in appliances. First, communications laid under the surface are prepared for connection. suspension system- ventilation ducts and electrical wiring. To do this, they are brought to the locations of the blocks and lamps. LED, raster or fluorescent lamps are inserted into Armstrong lighting size 590x590 millimeters. They are brought under small angle relative to the plane of the ceiling and unfold diagonally to the opening, aligning it with the cell. As a result, the lamps end up on the guide profile. Through neighboring empty cells connect the devices to the power cable.

• Installation of spotlights and split ceiling systems. They can also be used in Armstrong ceilings. To do this, holes are made in the slabs in accordance with the size of the lighting fixtures. After the tiles are returned to their place, point devices are connected. Air intakes are installed in the same way ventilation systems. It is better to install split system blocks in the most fortified places, for example, in a corner.
• Laying tiles. Blind elements are placed in place in last resort. They need to be brought into the cell diagonally and placed on the guides, then, lifting from below and turning, put in place.

The nuances of installing a ceiling structure in an apartment

With the task of how to install Armstrong in apartments standard layout, it is not always possible to cope. If the ceiling height exceeds 275 centimeters, installation is carried out using standard technology. In this case, the surface of the structure must be located at a height of at least 250 centimeters - this value is provided for by SNiP.

When ceilings are lower, then Armstrong can be installed in rooms where people stay periodically, for example, it could be a corridor.

Since such a ceiling has a low price, does not emit substances harmful to health, and is easy to install and maintain, the main thing is to choose the right one for it. quality material and corresponding design.

Combined from gypsum plasterboard and panels

Today we have to figure out how to install a suspended ceiling. We will look at two popular, affordable and practical solutions- from plasterboard and plastic wall panels. So, let's go!

About materials

First, we need to decide on the choice of one material or another. Both solutions, which we are about to get acquainted with, have a number of common and individual features.

General Features

Like any other, structures made of gypsum plasterboard and plastic panels allow:

• Hide any defects and unevenness of the floor;

• Hidden wiring, ventilation or any other utility networks;
• Avoid preparing the floor surface (stripping old coatings, sanding, etc.);

However: in damp rooms it is worth treating the surface of the ceiling with an antiseptic primer. It will prevent the formation of mold in conditions of limited ventilation.

• In both cases, on a lathing or frame made of galvanized U-shaped profile. Installation of gypsum boards and panels on timber is practiced, but in vain: the hygroscopicity of wood often leads to warping of the ceiling frame when seasonal changes humidity.

Differences

They relate to the performance properties of the two materials.

(including green, moisture resistant) does not tolerate direct contact with water. Gypsum is gypsum: moisture makes it loose. That is why gypsum boards should not be used in a bathroom or toilet that is periodically flooded by neighbors.

After the flood: gypsum board needs repair

PVC wall panels, on the contrary, have hygroscopicity tending to zero and will not be damaged even by prolonged immersion in water. After the next flood, you will only have to wipe off the drips.

With heat resistance, the picture is the opposite: gypsum board without any negative consequences tolerates heat up to 100-120 degrees. PVC at this temperature undergoes thermal decomposition, releasing hydrogen chloride, which has an extremely pungent odor.

Practical consequence: in plastic ceiling You should not install recessed lamps with halogen and incandescent light bulbs with a power exceeding 40 W. LED and fluorescent lamps can be installed without power restrictions.

Finally, gypsum board in combination with gypsum putty allows you to create structures with complex curved surfaces, arches and vaults. Honeycomb panels, which have limited flexibility, do not provide this opportunity.

Frame with a curved transition between levels

Frame

Do-it-yourself installation begins with assembling the frame.

For this we need:

Image	Description
	CD profile (ceiling, 60*27 mm). In the domestic naming system it appears under the name PP. This is what the horizontal lathing of a single-level ceiling will consist of; it is also used for the manufacture of racks of ceiling boxes and transitions between levels.
	The UD profile (ceiling guide, 27*28) is also known as PNP. Its task is to ensure fastening of the horizontal sheathing to the walls, as well as the racks to the floor surface.
	With a significant span between the walls, the lathing must be supported not only on the wall guides. Her additional fastening direct ceiling hangers will provide the ceiling.
	Dowel-nails will allow you to reliably and with minimal costs time to secure the wall guides. The most popular fastener sizes are 6*60 and 6*40 mm.
	Wedge anchors will perform the same functions when installing guides for a box or transition between levels, as well as suspensions. Unlike dowel-nails, they adhere perfectly to the hollow-core floor slab and do not threaten the ceiling to collapse in the event of a fire.
	Self-tapping screws for sheet metal connect the profiles to each other. Their optimal length- 9 mm. The presence of drills and press washers is welcome.

What is the procedure for installing a suspended ceiling at the frame assembly stage?

Single level

1. Mark the line along which you will attach the guides to the walls ceiling profiles. Marking is done according to a level (preferably a laser or water level) using a painting cord or a ruler with a pencil;