Technoelast TKP slate gray is a waterproofing roofing material Premium class with excellent performance characteristics. It is a canvas with a base made of reinforced fiberglass, which is coated with bitumen-polymer binder on both sides. The bitumen layer contains various additives and modifiers, which improves the properties of the material. To protect against mechanical influences, ultraviolet radiation and increase heat resistance, a coarse-grained gray slate coating is applied to the upper side of Technoelast TKP. The lower part of the panel is protected by a polymer film with the logo of the manufacturer.

Roll roofing Technoelast TKP gray slate is produced by TechnoNIKOL. It has quality certificates and is highly reliable and durable. The material can be used as roofing and waterproofing of foundations, basements, bridge spans, swimming pools and others engineering structures. The service life is at least 25 - 30 years.

Advantages and features of Technoelast TKP

Technoelast roll waterproofing has excellent performance characteristics. Its installation can be done at any time of the year, even in winter at temperatures down to -30 °C.

Main advantages of the material:

• withstands large mechanical loads;
• absolute waterproofness;
• high heat resistance and biostability;
• large margin of safety and durability;
• resistance to rotting and ultraviolet radiation;
• simplicity and high speed of installation;
• versatility – wide scope of use;
• preservation of consumer properties in wide range temperatures

It is worth noting that the base price of Technoelast TKP gray slate will not be very low - it is at the average level among weldable materials of its class. However, its purchase is justified due to its long service life and reduced roof operating costs. After all, the degree of wear of the material after five years of operation will be only 22%. And if you use it as the top layer of a roofing carpet, then the first leaks due to wear may appear no earlier than 18 years after installation.

Scope of application and installation features of Technoelast TKP roll roofing

The material has high tensile strength and excellent waterproofing characteristics. It is recommended to use it for the top layer soft roof on concrete foundations or durable cement-sand screeds. Slate topping on outside roll reliably protects it from negative influence various factors: sunlight, precipitation, mechanical damage. It can also be used when doing repair work and for moisture protection of foundations, swimming pools, basements, tunnels and other structures with increased reliability requirements.

Technoelast is laid by fusing using a gas torch. The canvases are laid overlapping on a previously cleaned and primed base. By the way, the logo, which is applied to the protective film on the bottom side - on the deposited layer, serves as a kind of indicator during the installation process. When exposed high temperature it changes color and shows whether the covering bitumen is sufficiently heated to ensure reliable fixation of the panels to the base.

The online store “Roofing and Insulation” offers to buy Technoelast TKP gray slate at an economically feasible and competitive price. And a flexible system of discounts will allow our customers to purchase this popular material from the TechnoNIKOL concern at an even more attractive price, without even leaving their office or home. Call, ask questions to managers or place an order directly on the website!

Reading time ≈ 3 minutes

Technoelast is a built-up roofing material for the construction of flat roof, protection building structures from negative impact water. It has high strength and elasticity: it retains flexibility at a temperature of minus 25 degrees, ductility at -40 degrees. Thanks to such properties and positive customer reviews, it is popular in different regions, but is widely used in northern regions, areas with high ground pressure.

The basis of this material is fiberglass, fiberglass, polyester. They are coated with bitumen-polymer binder, coarse/fine sprinkles (red, green, gray colors) or polymer film.

Technical characteristics of technoelast

Technical characteristics of technoelast grades: EKP, TKP, EPP, HPP:

Main types of technoelast

According to the scope of technoelast, type protective level The following modifications are distinguished:

• Technoelast EPP- polyester-based material with a high-strength protective film. It is very strong and has a stretchable lining level. Used for the base layer flexible roofing, its waterproofing, waterproofing of the floor, foundation, basement, utility rooms;
  • E - polyester
  • P - film
  • P - film
• Technoelast EKP- polyester base with coarse powder and a layer of polymer film. Due to its increased reliability, it is used for the upper level of a flat roof, barn roof, garage;
  • E - polyester
  • K - baby
  • P - film
• Technoelast HPP- fiberglass base with a protective polymer layer. Used for waterproofing floors, basements, foundations, flat roofs, vapor barriers, garage roofs, utility rooms, pipe insulation;
  • X - canvas
  • P - film
  • P - film
• Technoelast TKP- the base is fiberglass with a polymer film and coarse-grained topping. Suitable for the top level of a flat roof, garage roof, cottage, barn.
  • T - fabric
  • K - baby
  • P - film

There are 2 groups according to purpose:

• Technoelast K- for arrangement of the upper level of the roof. For its production, shale coating is mainly used, which protects against solar ultraviolet radiation;
• Technoelast P- when installing the lower layer of the roof. Fine-grained powder protective film prevent material sticking.

Advantages

• durability - the material is designed to last 30 years;
• elasticity - retains plasticity under severe temperature fluctuations, can be lengthened, stretched, and can be fused onto building structures of various shapes;
• high quality - high-quality bitumens are used for production;
• reliability - successfully resists mechanical, air, and biological influences;
• Can be used on any surface;
• technoelast has good waterproofing, excellent sound absorption, and retains heat;
• environmental friendliness - does not provide harmful effects to nature, man;
• good adhesion - the artificial rubber in the composition provides strong adhesion to different surfaces;
• ease of installation and installation.

Technology development does not stand still. This also affected construction market. More and more advanced materials are being created that have high levels of strength, durability and reliability. One such material is EPP technoelast, specifications which makes it the most popular. This article describes what technoelast is and where it is used. Its modifications and composition will be considered, as well as what the letters E and P mean for the technical characteristics of the EPP technoelast.

What is technoelast?

Technoelast is a rolled roofing material that is characterized by high reliability, waterproofing capabilities and high strength. Thanks to its properties, technoelast can be used in any climatic conditions. Technoelast is used for covering roofs, waterproofing foundations, swimming pools, garages and other structures.

The production technology consists of applying a layer of a mixture of bitumen, SBS thermoplastic (and its modifications) and filler on both sides to a durable and fairly flexible base. SBS is an artificial rubber, and fillers can include talc, dolomite and other substances. The top and bottom layers are film or crumbs. It is the film that protects the material from gluing during storage in a roll, and it is also melted during the installation of technoelast. The crumbs can be either coarse-grained or fine-grained. Shale, sand, etc. are used as it.

Explanation of the abbreviation and main modifications of technoelast

Technoelast is available in several modifications, each of which has its own conditions and area of ​​use. And the letters indicated in the modification are deciphered as follows:

• The first letter of the abbreviation is the material from which the base is made. It can be: polyester (ester) - E, canvas - X or fabric - T;
• The second letter of the abbreviation is the type of top protective layer. It can be: crumbs - K, film (or fine-grained topping) - P;
• The third letter of the abbreviation is the type of undercoat. It also comes in two types - crumb (K) and film (P).

Depending on the combination of these layers, the Technonikol company offers several types of technoelast:

• Technoelast EPP is a waterproofing material for various construction projects. Apply it as various types, and for waterproofing floors, buildings, foundations, boiler rooms, swimming pools and other buildings. In addition to absolute waterproofness, it also has high elongation and high heat resistance. EPP is made from which SBS thermoplastic and filler are applied. The bottom layer is a film, and the top layer is a fine-grained topping. If it is used as waterproofing for building structures, it is fused in two layers using a torch.
• Technoelast EKP is a roofing waterproofing material that is used as upper layer. It is often used with EPP technoelast, thereby increasing reliability roofing works. EKP is characterized by high heat resistance and tolerates low temperatures (down to -30 o C). The main layer for the production of ECP is polyester (which is not subject to rotting) with a layer of bitumen, thermoplastic and filler. The top is covered with a large mineral film, and the bottom layer is a protective film.
• Technoelast TKP is used as a roofing material for the top layer of roofing sheets. It can also withstand high loads, so it is often used as a waterproofing agent for underground objects. The rolled material has high strength, increased reliability, and is resistant to steam and temperature changes. The base of the TKP technoelast is fiberglass, which is covered on top with SBS bitumen and thermoplastic. The top layer is crumbs, and the bottom layer is film.
• Technoelast XPP is a waterproofing material that is mainly used as a bottom layer for roofing, foundation, swimming pool, etc. It is resistant to frost and heat.
• TKP roll material consists of fiberglass coated with SBS-modified bitumen and filler, and film. Due to the absence of polyester and crumbs, it has the smallest thickness - 3 mm.

Technical characteristics of EPP technoelast

Technical characteristics of waterproofing technoelast EPP:

• top coating - film without logo; bottom covering - film with logo;
• weight not less than 4.95 kg/m2;
• the tensile strength of polyester during longitudinal stretching is at least 600 N, and at transverse stretching it is at least 400 N;
• thickness - 0.004 m;
• heat resistance - no less than 100 o C;
• length - 10 m, width - 1 m;
• complete waterproofness throughout the day at a pressure of no less than 0.2 MPa;
• moisture absorption during the day is not more than 1% of the mass;
• the flexibility temperature on the beam with radii of 0.025 m and 0.01 m is not more than -25 o C;
• the weight of the binder on the fusion side is not less than 2 kg/m2.

The characteristics of the produced technoelast correspond to the technical characteristics of EPP technoelast according to GOST 30547-97.

Advantages and disadvantages

Like any material, EPP technoelast has its advantages and disadvantages.

Advantages of technoelast:

1. Long service life. Waterproofing can last up to 30 years.
2. High quality raw materials for the production of technoelast.
3. Resistant to various types of impact - mechanical, biological, air.
4. It can be used on any surface.
5. Environmentally friendly. That is, it does not harm either humans or the environment.
6. High elasticity with large temperature fluctuations.
7. Has high thermal technical characteristics. Technoelast EPP also has high waterproofing and excellent sound absorption.
8. Easy to install and adjust.
9. Strong adhesion to a variety of surfaces.

Disadvantages of technoelast:

1. When installing, it is important that the surface is level.
2. Small selection of colors.
3. Burner heating takes longer.
4. The cost is above average.

Application area

Waterproofing with technoelast has gained great popularity for various construction work. Due to its technical characteristics, EPP technoelast is used primarily where protection against moisture penetration is needed. It is also used as a material for roofing carpet.

If repairs are necessary, technoelast is applied in one layer. If a new coating is needed, then two layers are required. At the same time, the top layer looks quite attractive, which allows you to avoid unnecessary expenses on a decorated coating.

Installation and storage

For long term waterproofing service, it must not only be selected correctly, but also correctly laid and secured.

The sequence of work is as follows:

1. The surface to which the technoelast will be attached must be thoroughly cleaned of dust. If there are potholes and holes, they should be cemented. Then degrease the surface of the structure.
2. To ensure adhesion of the technoelast, the base must be coated or diluted with bitumen mastic with gasoline (proportions 1:3).
3. At this step you need to roll out and cut the panel.
4. Warm up the bottom layer gas burner and press to the base. All subsequent sheets are fused with an overlap of 9-10 cm.

Storing technoelast is quite easy. First of all, it should be placed in a room with dry air, which is well ventilated. Rolls should be placed on shelves in a vertical position and in such a way that they are away from heating devices at a distance of no closer than a meter.

If you need to ensure maximum waterproofing, then ideal solution There will be technoelast EPP. The technical characteristics of the rolled material allow it to serve reliably and for a long time.

Multifunctional SBS (polymer)-modified, weld-on roofing and waterproofing material of increased reliability.
Flexibility on the beam R = 25 mm, not higher than - 25 0 C, heat resistance + 100 0 C

Designed for installation of roofing carpets for buildings and structures, waterproofing foundations and other structures with increased reliability requirements in all climatic regions. The element of Technoelast is the cold of the polar night and the constant pressure of man-made groundwater. It is used where other materials are unlikely to provide the required level of protection against water. Technoelast is always where serious construction projects. It is there where only the highest reliability is needed.

Technoelast review

Technoelast is intended for installing roofing carpets on buildings and structures, waterproofing foundations and other structures with increased reliability requirements in all climatic regions. Technoelast's element is the cold of the polar night and the constant pressure of man-made groundwater. It is used where other materials are unlikely to provide the required level of protection against water. Technoelast is always there where serious construction projects are implemented. It is there where only the highest reliability is needed. Technoelast is produced by applying a bitumen-polymer binder containing bitumen, SBS thermoplastic and fillers to a fiberglass or polyester base. Coarse-grained K, fine-grained coating M and polymer film P are used as a protective layer. Technoelast is fused using a propane torch.

Features of Technoelast

Technoelast is biostable.

Application area

Designed for installation of roofing carpets on buildings and structures and waterproofing of building structures.

Structure of Technoelast

Technoelast is produced by double-sided application of a bitumen-polymer binder consisting of bitumen, styrene-butadiene thermoplastic elastomer and filler onto a glass or polyester base. Coarse-grained and fine-grained dressings and polymer films are used as a protective layer.

Technoelst brands

Depending on the type protective layers and areas of application Technoelast is available in the following grades:

TO

With coarse granular topping front side and polymer film or fine-grained coating on the surface to be welded; used for installing the top layer of roofing carpet;

P

With fine-grained powder or polymer film, or a combination thereof, on both sides of the canvas; used for installing the bottom layer of roofing and waterproofing building structures (foundations, tunnels, etc.).

Table Characteristics of Technoelast

800/900

Parameter name		TO	P
Cover type:	top	film	film
bottom	slate	film
Weight, kg./sq.m. no less		5.0	4.6
Tensile strength in longitudinal/transverse direction, N, not less	on polyester	600/400	600/400
	on fiberglass	800/900
	on fiberglass	294	294
Thickness, mm		4.2	4
Water absorption for 24 hours, % by weight, no more		1	1
Weight of binder on the welded side, kg/sq.m., not less		2	2
Loss of powder, g/sample, no more		1
Flexibility temperature on timber R=25mm, оС, not higher		-25	-25
Flexibility temperature on the beam R=10 mm, °C, not higher		-25	-25
Binder brittleness temperature, °C, not higher		-35	-35
Waterproof for 72 hours at a pressure of at least 0.001 MPa		absolute
Waterproof at a pressure of at least 0.2 MPa, for 2 hours			absolute
Length\width, m		10x1	10x1
Heat resistance, °C, not less		100	100

Manufacturing jobs

according to the "Guidelines for the design and installation of roofs from bituminous materials"TechnoNIKOL" Corporation" can be used in all climatic regions according to SNiP 23-01.

• from the factory price we subtract a part (quite large) of our dealer discount;
• We minimize the cost of material delivery;
• Our warehouses are open at night because... night transport is cheaper;
• Delivery to the regions is carried out by factory vehicles.

We deliver Technoelast during the day and at night, it is possible different kinds car awnings (rear, side, top). For large orders we offer object discounts. We create prefabricated vehicles with different brands of TechnoNIKOL waterproofing. We successfully work with regions.

Technoelast marking

In order not to make a mistake with your choice, we suggest that you familiarize yourself with the product labeling:

• E, T, X– designation of the base on which the material is made, E - polyester, T - fiberglass, X - fiberglass;
• P, K- designation of the upper protective layer of the roll (P-polyethylene film or K-stone chips);
• P- designation of the bottom protective layer of the roll (polyethylene film);
• Number at the end of the marking indicates the weight of one m2 of material (the larger the number, the thicker the material).

Varieties of Technoelast

• Technoelast P(lining) - for the bottom layer of the roofing carpet and for waterproofing works for various purposes (internal and outer side roll protected plastic film).
• Technoelast K(roofing) - for the top layer of the roofing carpet (in this case, the lower part of the roll is protected with plastic film, and the upper part is protected with coarse-grained coating of various colors).

Technoelast based fiberglass - This is Technoelast XPP, Technoelast Thermo XPP, used for waterproofing and roofing work on unloaded structures with a low slope, which during operation do not experience high tensile and tensile loads.

This is Technoelast TKP, Technoelast Thermo TKP, has best characteristics to break.

These are Technoelas EPP, Technoelast EKP, Technoelast Thermo EPP, Technoelast Thermo EKP, they have excellent tensile characteristics, therefore they are used in more critical areas of roofing and waterproofing. Special grades are used in accordance with the manufacturer's recommendations.

Production and use of Technoelast

Technoelast is produced by applying a bitumen-polymer binder consisting of bitumen, SBS (styrene-butadiene-styrene) polymer modifier and mineral filler(talc, dolomite, etc.). Coarse-grained and fine-grained dressings and polymer films are used as a protective layer.

Technoelast is one of the most the best materials Premium class, which are produced in Russia. Different brands Technoelast is used:

• for waterproofing the foundations of buildings and structures for various purposes;
• for waterproofing bridges, tunnels, overpasses, underground structures;
• for waterproofing flat roofs and low-slope roofs, as well as “breathable” and “green” roofs;
• to protect building foundations from radon and methane gas;
• for installing roofing carpet using a fire-free method;
• for roofing and insulation at facilities where increased heat resistance of materials is required (withstands heating up to 140 degrees);

Laying can be done all year round. Even with very low temperatures it does not lose its elasticity and strength, in the heat it does not stick together and does not “flow”.

Special brands of Technoelast

TechnoNIKOL company produces Technoelasts special purpose- This is waterproofing, which is designed to solve very specific problems.

• -bitumen-polymer waterproofing material, which can withstand heating up to 130 degrees; no other rolled waterproofing material has such heat resistance. Produced on a base of fiberglass and fiberglass. It is used for waterproofing in hot regions and places with high operating temperatures.
• - self-adhesive baseless bitumen-polymer hydro-vapor barrier material. Used for waterproofing shallow foundations, waterproofing interior spaces under screed, vapor barriers of building structures. Installation using a fire-free method is possible at sites where the use of open flames is prohibited; installation on flammable substrates is possible.
• - bitumen-polymer waterproofing material intended for waterproofing reinforced concrete slabs of the roadway of bridge structures, for installing a protective adhesion layer on a steel orthotropic slab of spans of bridge structures, as well as for waterproofing spans with reinforced concrete slab roadways on which asphalt concrete pavement, including those made from cast mixtures with temperatures up to 220 °C, is laid directly on the waterproofing.
• is a rolled spacer soundproofing material for soundproofing floors between floors of buildings. Material prevents spread impact noise, transmitted by load-bearing structures building.
• is a bitumen-polymer waterproofing material. It is used for waterproofing buildings and structures with gluing to mastic. This technology allows you to combine the benefits of waterproofing from roll materials(with high physical and mechanical properties) and seamless monolithic mastic waterproofing. Used for fire-free mastic installation.
• -bitumen-polymer waterproofing material. It has improved fire-technical characteristics according to SP 112.13330: flame propagation group RP1 (non-flame propagation); flammability group B2 (moderately flammable).
• - This is a rolled hydro-gas insulating material. It is used for hydro- and gas insulation of underground parts of buildings and structures. Protects against exposure to radioactive gases, including Radon gas. It is used as an outer (ground-facing) layer in two-layer waterproofing.

If you have any questions about roll waterproofing Technoelast - call and ask our managers, we will try to answer everything.

BUY IN ONE PLACE, SAVE ON DELIVERY, TAKE USE OF REGULAR CUSTOMER DISCOUNTS