Flower pots are quite popular, and you can find a lot of instructions on how to make them online. In one of ours, we already told you how to make hanging flower pots with your own hands, but today we offer you a different approach. There is no need to make the pots themselves; we offer completely ordinary flower pots to turn them into hanging ones.

Materials and tools for making hanging flower pots:

• 3 small flower pots with planted plants
• a roll of thin clothesline
• 15 untreated wooden beads, approximately 18mm in diameter
• 9 wooden beads with a diameter of 25 mm
• 11 beads with a diameter of 38 mm
• ¼ inch copper tubing
• pipe cutter
• acrylic paint
• tassel

DIY hanging flower pots

Paint the beads in different colors. If you want the paint to lay down in an even layer, the beads can first be sanded with sandpaper.

Advice: The easiest way to dry beads is by placing them on a wire.

A rather interesting effect is obtained if you paint the beads for each pot in different shades of the same color.

Pull two ropes through each group of beads. In our case, to make each pot, a pole of ropes was used, tied at the top into a knot.

Beads can be placed in any order. In our case, their diameter first increases and then decreases.

Decide on the height at which you want to fix the wooden beads, and tie a knot in this place on each pair of ropes.

Separate each pair of ropes, and knot the left rope from the first pair with the right rope from the second. In the same way, tie all six ropes in pairs. Repeat the procedure again, moving downwards.

Tie all three pairs of ropes in one knot, trim the ends of the ropes, or leave them as is.

Using the same principle, we make the second hanging pot.

Cut the copper pipe into lengths of about 70 mm.

Alternating multi-colored wooden beads and pieces copper tube, decorate each pair of ropes. In this case, it is better to use small beads so that their diameter is not much larger than the diameter of the tubes.

Secure the beads and tubes with knots.

Separate each pair of ropes and tie them to ropes from adjacent pairs. Repeat the same, moving down slightly. Tie all the ropes into one knot.

Place a flower pot in each of the resulting rope sleeves. Now all that remains is to hang the pots in the window or doorway, decorate your veranda or living room with them.

To decorate hanging pots, it is not necessary to use wooden beads and copper tubes; it all depends on your imagination.

Original article in English.

Any room has a finished look if there are plants in it. They not only decorate the interior, but also give comfort and bring joy. In addition, plants are known to purify the air, which is very important especially for urban residents.

Growing plants is a lot of work that requires time and skill. Each plant has its own characteristics, living conditions, needs a certain humidity, temperature, and light.

Gutter: a simple DIY hanging garden idea

An original idea for a hanging garden would be a gutter; this simple device will wonderfully decorate both city apartments and any garden or cottage.

In order to turn the idea into reality, you will need gutters (several pieces), hooks, metal cable and clamps. Let's make holes along the gutter and thread metal cables into them on both sides; secure the cables with clamps from the bottom of the structure. On the next gutter, following the first example, you should drill holes and thread the cables parallel to the first one. The structure will not move if the fastening points are strictly below each other. All that remains is to attach the hanging garden to the hooks, fill it with soil and plant the plants. Master Class:

Preparing the gutter

Clips and cable

Drilling holes

We stretch the cable

We install fasteners

Hanging the gutter

Planting plants

The kindergarten is ready

A similar idea for hanging gardens, implemented more simply - using plastic bottles. It’s not so impressive to make it, but doing it with your own hands is quicker, simpler and more accurate than anyone can do.

Hanging baskets made of climbing plants

There is a huge selection of special hanging pots with a tray for excess moisture. They can be made of any material: wood, metal, woven from branches, ropes. In addition, you can easily make a hanging flower pot yourself without special effort from improvised means.

Plants hanging on a special flowerpot made of rope or cord look very beautiful. Good choice For such decorative tableware, a fern or ivy hanging in the air will become, as if hanging in the air. Or use regular hanging pots for flowers and houseplants.

Hanging flower pots - the simplest solution

Using saw cuts of various tree species, you can make original hanging pots for the same ivy, as well as vines. An original pendant made from bamboo sticks or slats, as well as a piece of wood in which you can make a small depression, will successfully combine several types of plants that do not have a very developed root system. Or you can use bags made from regular fabric. This is how you can decorate a fence at your dacha.

Baskets made of galvanized wire have become widespread. They are the most durable and quite an unusual design solution. You can also make a hanging garden from ordinary galvanized or painted buckets.

An interesting idea is to make a hanging garden without using any pots or things that replace them at all. We'll just have moss balls hanging on twine with green plants growing out of them. Here is the instruction “”, and here is what will happen in the end:

Hanging garden- piece of art

Hanging garden in pockets

A hanging garden in pockets is quite an unusual solution for placing plants. You can sew the pockets yourself or use a ready-made organizer for tools; you will also need a cornice and hooks.

The most important thing is to find a place for our future device under a canopy, so that in rainy weather excess water does not get into the pockets. We install the cornice in the chosen place and hang our canvas with pockets on the hooks. Now we fill the pockets with soil and plant the seedlings. All that remains is to attach wooden block for gravity and the hanging garden is ready! Instructions:

Hanging garden in pockets at the dacha - growing greens

We fasten the block

Planting plants

We fill up the earth

Sew pockets

Hanging garden upside down

Very creative idea for a hanging garden - use special upside-down pots. The plants in them do not grow as they should, but upside down. These original pots are called Sky Planter - search on the Internet, and they were invented by Patrick Morris.

How it works:

Hanging garden: A new idea from old boots

A pair of old boots lying around in the closet will fit well into any garden. Any boots made of any material and absolutely any size are suitable for decoration. Let's make a hole in inside shoes and insert a hook into it, which can then be secured anywhere. The main thing is that the hooks are strong, since a boot with soil can weigh quite a lot, and when watering our “ flower pot" will become much heavier.

Hanging plants will look especially good in such an interesting device. various colors and varieties.

Hanging pots for the garden with hanging plants Did you like the article? Share on social networks!

Sooner or later, in the lives of many flower growers the question arises: “Where to put it?!” The place is over! Indeed, green pets have filled all available places and surfaces, and are threatening to evict their owners from their legally occupied bed. Household members are shouting indignantly that there could be fewer plants, but who will listen to them? How can you refuse cacti, violets, ficus and other beauties, nurtured with such labor and love? And there is no need to refuse, because relatives are making noise, most likely, just for show, but they themselves secretly admire the green kingdom and proudly tell their friends: “And we have such a monstera!” In half the room! and casually examine the less well-groomed specimens of these acquaintances.

However, the reaction of others still does not solve the problem of the place, and here you have to call on your imagination and skillful hands to help. It’s good if your hands are in the right place and your imagination is in order. And if not, we’ll try to help with our imagination in this article, and I’m sure one of the male half of your large family will have skillful hands.

On the Internet you can find many ideas for creating all kinds of walls, shelves and stands, but in this article we will look at those that are located directly on the window. This will solve the problem of lighting without additional lighting, and will not require extra space in an already crowded house.

Ampelous plants on the window

For this option, we will need several anchors with a hook; select the diameter depending on the expected weight. I think 6 mm will be enough (anchors for an 8mm drill are used in the photo). Drill or hammer drill upper slope We drill holes in the windows and insert an anchor. Anchor - from the word anchor, is a metal hook with a spacer part at the opposite end. It is inserted into drilled hole and twist the hook clockwise. At the same time, the spacer mechanism expands and is held tightly in the hole, like an anchor. On such a hook, unlike a self-tapping screw on a dowel, you can even hang a swing.

So, it's done! All that remains is to hang the pots with plants. This placement option is suitable if you have both wooden and plastic windows. Designed primarily for hanging plants, but in conditions of acute shortage of space, any small plants can be planted in hanging pots. For example, I have a cryptanthus growing in such a pot, although it is not a hanging plant at all; in a hanging pot, a herbivorous cat cannot reach it.

Thus, you can use anchors to hang plants above the window and in the immediate vicinity of the window if drilled into the ceiling ( ceilings always concrete, so drill only with a hammer drill). If you don’t have anchors, you can use self-tapping screws with dowels or hooks with dowels; you can hang a cord or a chain of flower pots on them, but the hook is more reliable - the rope won’t just fly off from it.

Shelf for flowers on ribbons

We call it student among ourselves. The idea arose while living in a student dormitory, where this model was quite easily created by fragile girls to house the state supply of cosmetics. Afterwards it was modernized and implemented for plants.

We will need a board whose length is slightly less than the width of your window, but it is better to use 10mm thick plywood. You will also need several meters of fabric belt (also called a harness, used for making reins and other economic needs) and 4-8 self-tapping screws. This option is only suitable for windows with wooden frames.

Calculating the length of harness you need is very simple. Either empirically, or using the formula 2ШД+4ВП+10 cm, where ШД is the width of the board, VP is the height from the attachment point to the shelf. We divide our ribbon in half and cut it. Fold it in half and screw the ends of the harness to the frame with 2-4 self-tapping screws. After this, we lay the board on the resulting loops, maintaining its horizontal position. That's it, you can put flowers. Of course, the appearance of such a shelf, to put it mildly, is not very aesthetically pleasing for an apartment, but it is quite suitable for placing flowers on a balcony, on a veranda, or in a country house.

Let's improve this placement option: instead of a board or plywood, we use a plastic tray. It is more effective - the sides will not allow the pots to move and fall, and if you place many small pots on it, for example, with cacti and other succulents, then it is easy to remove all the pots at once along with the tray. For fastening we use tapes that are sold in any sewing supply store: keeper tape, hem tape (for trousers) or belt tape (belts and bag handles are sewn from it).

Glass shelf for flowers on metal corners

Suitable only for those who have wooden windows. Needed metal corners with a stiffener, which are sold at any hardware store and wooden slats 3.5-4 cm wide and 1.5-2 cm thick.

The corners can be taken in lengths of 10 cm and 25 cm. The rail is cut into strips according to the width of the future shelf, and attached to the corners with screws. Glass was ordered from a hardware store according to the specified dimensions. The width of the glass was 25cm, length 110cm (this length at three corners). The edges of glass shelves need to be sanded to avoid cutting. The glass is very easy to sand, for this I first took coarse sandpaper, then medium sandpaper, all for about 15 minutes of work. But it seemed to me that this was not enough, so that the veil on the window would not touch or tear at the corners of the glass shelves (and they are very wide), I cut off the corners of the shelves on one side - the one away from the window.

These shelves are convenient because the glass is not secured with anything, it can be removed at any time to wash the windows, etc. And so, in general, a very stable design. I have one glass on a rail and on double-sided tape - for reliability.

Side shelves for flowers on the window

Author Marta. This placement option is similar to the previous one. Materials: two slats, 2 cm thick, 3-4 cm wide, the length of the slats is equal to the height of the window opening. The slats are attached to self-tapping screws with dowels at two points (top and bottom) of the side slope of the window. Metal corners with stiffening ribs, approximately 10-15 cm long, are attached to these slats. At a distance of approximately 40-50cm from each other. Shelves made of thick plywood, 10mm thick, are installed on the corners. Approximate dimensions of the shelves: 20-25cm by 30-35cm. These are the dimensions for the window opening panel house. In a brick house, the walls are thicker and the length of the shelves can be up to 50cm. Sheets of plywood prepared for shelves need to be sanded so as not to get a splinter and varnished or painted with enamel.

An alternative to such shelves can be wall planters or decorative hooks for hanging pots. By the way, it is necessary to make a reservation that the shelves placed on the side slope of the window have one drawback: the flowers standing closer to the window are illuminated better, and those that stand “second” are worse. Therefore you need to either install fluorescent lamps from the side of the room, or periodically turn the flowers on the other side towards the light, or change places. The same flowers that are placed in the photo in the very top tier receive the least amount of light; the most important ones should be placed there. shade-tolerant plants, or install additional lighting from above.

Placing plants on a trellis

“I have quite a lot of large pots containing single stem plants, I tried to plant some little ones in them, but I didn’t really like it and they liked it, and it’s difficult to find an ideal community. So the solution was this: take a lattice suitable in size (I make it myself either from slats, or from cut wooden rulers, assemble it into any convenient shape, or twist it with thin wire or PVA), and install it on the pot, and you can put anything you like on the lattice, and there’s a lot of space savings are saved and decorativeness is not only preserved, but also acquired! " Photo by Natalya Matyushevskaya:

We make a note: this method is convenient when there is space under a large plant in a wide pot, and you can place several small pots with medium-sized flowers (for example, mini violets, fittonias, rooting cuttings of other plants). Even in this case, you cannot place other pots on the grid too tightly, otherwise the soil in the pot under the crate will not dry out and breathe well, which will have an adverse effect on the “mother” plant.

Hanging shelf on the window

We will need: 4 anchors with a hook (these were mentioned above), two 10mm pieces of plywood from which we will make shelves, a thin metal cable or strong rope. We fix the anchors in the upper slope, measure the required length of the cable, secure it on the hooks and in the corners of the first board using fasteners (you can screw in the same hooks as on top, but smaller). WITH reverse side We also attach fastenings to the boards, and we also fasten them to the second board on one side. We connect the boards with cables so that the bottom one lies on the window sill, and the entire structure is stretched quite tightly. When placing pots with plants on the lower shelf, the loaded upper shelf will hardly swing.

This system can be used only for one shelf, which will be the length of the entire width of the window, with the only difference being that it will have to be secured on six or more hooks in the upper slope.

Shelves for flowers wide window sill

The simplest shelf option is a prefabricated shelf from a hardware store. There is no need to describe - everything is clear from the photograph. The shelf is corner, can have 3-5 tiers. It has a disadvantage - the sides steal light (they block the lower plants). Therefore, additional lighting may be needed. The west-facing window shown in the photo has a lot of sun, so there is no need for additional lighting. It is advisable that the shelf be made only of light plastic, White color reflects light and the window will be brighter.

A more complex and expensive option is a glass shelf on metal holder legs. The shelf shown in the photo was made according to a sketch in a company that manufactures custom furniture. But if you have the opportunity to visit the store furniture fittings, and there is a handicraft man in the house, you can make such a shelf yourself. The shelf can be corner made of rounded glass or rectangular.

Another type of shelf is a metal flower stand, originally its length was about 2 m (see photo). last photo). The shelf was sawn to the height of the window opening and inserted into the spacer. Because The window is plastic so as not to scratch the slopes; pieces of foam plastic are placed under the ends of the rack. Polystyrene foam can be replaced with a piece of isolon, folded in several layers. Below are a few more photos of forum members who have adapted whatnots and stands for flowers on window sills.

Sincerely, Oksana Dyachenko ()
Natalia Rusinova ()

Indoor flowers in flowerpots are a wonderful way to decorate an apartment or house, making the room more lively and cozy.

In this article we offer you interesting ideas how to make beautiful hanging flower pots using a variety of materials, such as wood, leather, twine and other available materials.

Also 5 step-by-step master classes with diagrams and photos on how to weave flower pots quickly and easily with your own hands and create a truly beautiful decor interior

Leather hanging planters easy to make, but look very original. Add a little style to your home interior along with this wonderful leather planter. It can definitely become the highlight that makes the interior unique.

Master class: leather hanging planter

Necessary materials:

• Distilled (purified) water
• Tracing paper (21x28 cm) and 4 pieces of strong rope (or leather laces), each approximately 90-120 cm in length
• Leather dye (optional) and gloves
• Leather (square size 30x30 cm)
• Packing tape, a pencil and a utility knife
• Computer and printer (to print the template) and template
• Sponge for wetting and staining

Step by step diagram:

Step 1: Preparation and Placement

Print the factory hanger template on tracing paper. Place the template down on the wrong side of the leather and select perfect place placement (not too close to the sides, and to avoid any defects in the skin).

Step 3: Soften the skin

Dip the sponge into purified water and then apply the moisture evenly to the skin. Repeat this step at least three times until the skin looks like it can't take in any more water. This will soften the skin and make it easier for us to weave the flowerpots.

Step 4: Transferring the Template

Now place the template on the previously selected location and tape it to the sides so that it does not move to the sides. With a simple pencil draw the lines printed on the tracing paper by pressing the pencil with medium strength. Be careful and don't miss any line.

Step 5: Cutting

Now remove the template from the leather to see how the design has been transferred to the surface of the leather. Using a utility knife, make cuts along the lines.

For convenience, you can first cut a circle along the outer contour. The cuts should be clearly along the drawn lines.

Step 6. Coloring

Note: This step is optional and depends on the color you want and the materials you have on hand. In our case, we painted the leather dark brown.

After the skin has dried from moisture (at least one hour), apply the desired dye. Apply the paint using a sponge (wearing gloves) until the desired effect is achieved.

As the leather dries, pull it back a little at a time to create a voluminous shape. You will start to see the skin deforming, continue pulling and stretching it to create the shape of the pot for the pot as it should be when finished.

Step 8: Hanging

• After that, how the skin dries completely, and the shape of the planter is formed, punch four holes in the top to thread the ropes through.
• You should place them evenly, at the same distance from each other, so that the hanging flower pot does not tilt in one direction.
• Take four ropes (regular or leather) and tie a knot on each of them, tightening it tightly at the end.

Step 9: Decoration and installation

Add tassels, beads, rivets- everything you need to achieve the desired style in the end. At the top of the hanging cords, gather all four of them together and tie them into a knot.

You can use this knot to hook onto a ceiling hook and/or ring. See if the length of the pendant suits you; if necessary, tie the knot at a different level.

Hanging planter made from straws

This pot will suit the interior with an innovative touch. Transform and complement your home decor with these neon straws and thread stands. Moreover, even 15 minutes will be enough for you!

Necessary materials:

• Neon threads
• neon straws (8 pieces per pot)
• flower pots for indoor flowers(we used white ones from melamine)
• house plants (succulents)
• scissors

How to weave - instructions:

Step 1: Cutting the threads

Cut eight pieces of neon cord, each 90-150 cm long, depending on how close to the ceiling you want to place the pots.

Step 2: Making a Knot

Take the newly cut strands together and tie a knot at one end, creating a tassel from the small excess cord at one end.

Step 3: Divide the threads into sections

Lay out the rope into four sections (like a cross shape). That is, two ropes in each section.

Step 4: Cutting the Straws

1. Cut off the small part of the straws that is separated by the spring. Then cut it in half. Take eight of these small pieces and thread a thread into each of them.
2. Push the straws towards the center(knot) and make a knot on every two threads (in sections). This is what it will look like:
3. Arrange the threads again in a cross shape, two threads per section. Only now, to form a section, take one thread at a time from the previously adjacent sections.
4. Cut the straws into pieces (16 total needed), each of which should be the size of a part of a straw, which is separated by a spring.
5. In each of Thread 8 pieces of straws and make knots on the threads from one section.
6. Similarly, arrange 2 threads in a cross shape, one from adjacent sections.

Add the third and final set of straws to the threads and tie adjacent threads (similar to the previous set).

Step 5: Hanging

All that remains is to hang the flowerpot and insert a flowerpot with indoor flowers into it. Make several pieces, then together they will create a beautiful composition.

And neon straws will also glow a little at night, which will look very original.

Macrame flower pots

The macrame technique probably has the most variations in making pots. They can be either very simple, which can be done in literally 10-15 minutes with your own hands, or complex with many hours of work. Practice weaving first on easy ones, hone your skills, and then improve.

Master class: Do-it-yourself macrame weaving

Macrame is back in fashion again, as is handicrafts in general. In this master class you will learn how to make a hanging plant pot with your own hands using this technique. There is nothing complicated, just follow the instructions and you will succeed!

Necessary materials:

• 3 cords 2.5 m long and 0.5 cm thick
• Metal ring with a diameter of 2.5-3 cm
• Hook (on the wall, slot) to hold the macrame while working
• Scissors and colored rope
• Glass pot in the shape of a ball with a diameter of 20 cm
• Drainage stones and soil
• Houseplants that climb (eg Stephanotis)
• Decorative moss (optional)

Step-by-step instruction:

Step 1: Thread the ropes into the ring

Pull all three ropes through the metal ring until the ring is in the middle of the ropes. Thus, you now have six ropes to work with, each 1.25 m long.

Step 2: Making a Knot

1. Of all tie a knot with six ropes right next to the ring. Make it as tight as possible; to do this, after forming the knot, pull each rope separately.
2. Hang the ring on a hook (if there is no hook, then use a separate small rope to tie it to a cabinet handle or something like that, the main thing is to secure it). This will allow you to use both hands while working.

Step 3: Divide the cords into groups

• Separate the cords into three groups, two in each. Tie a knot in each pair 45cm below the ring. You will have three knots at the same level, make sure they are tight.
• Take one rope from two adjacent pairs and tie them together approximately 12 cm below the previous node.

Repeat the previous step with the remaining ropes so that they are all tied together. This will create a zigzag pattern between the cords.

Step 4: End Node

1. Approximately 12 -15 cm below the second set of knots, gather all six ropes together to make one large end knot. Pull each cord individually to make the knot as tight as possible.
2. Look what you need to leave the length and cut the ropes to the required size.
3. Wrap colorful threads around the rope in several places, creating blocks several centimeters long. This stage is decorative and is performed at will. Now the macrame pendant is ready and you can place the pot in it.

Step 5: Planting indoor flowers

To the bottom glass pot Place drainage stones to create a layer about 2.5 cm high. Fill the rest of the bowl with soil.

1. Remove the plant from the temporary pot and place it in glass vessel. Apply water and press down on the soil to compact it. You can place decorative moss on top of the soil., optional.
2. Place the glass bowl with the flower over the lowest node and spread the ropes to the sides to secure well.
3. Straighten the plant if it gets tangled in the strings. Hang it and admire the beauty of the plant and your own product.

Macrame patterns for flowerpots

Here are a few more patterns for those who want to master macrame weaving. They are very simple - suitable even for beginners. We look at the photo and repeat. Clothesline or thin twine are perfect materials. The minimum consumption for a hanging planter is 10 meters of rope.

Wooden flower pots

Wood also provides a fairly wide range of actions, various shapes and colors. Choose what you like best and create.

Master class: hanging wooden planter

This hanging planter will wonderfully complement your home interior. It’s quick and easy to do, and it won’t cost you a lot of money on materials either. The optimal solution for an apartment.

Necessary materials:

• Wooden plate and saw
• House plants and flowerpots
• Rope and metal ring
• Drill and sandpaper
• Paint and brush

Step-by-step manufacturing scheme:

Step 1: Making Wooden Squares

Think about how many tiers your flower stand will have ( there are 4 here, but you can do more or less ). Select the houseplants you want to place there.

Based on all this, cut from a wooden plate required quantity squares.

1. To do this, turn the pot upside down and place it on a plate, circle it and leave it on the sides approximately 5 cm each, thus determining the size of the square.
2. Using a saw make squares.

Step 2: Making holes for the pots

1. You already have a circle drawn on the tree from the top of the pot, now you need to draw another one in the middle so that their centers coincide, but the diameter of the new one is about 1-2 cm smaller.
2. This value depends on how quickly the pot you will place in the stand increases towards the top, and also you want so that the wooden square is almost at the very top, or in the center of the pot.
3. You can take another pot that is the same size as the stencil and trace it.

• Use a jigsaw to cut out this new circle. For convenience, you can first make a hole with a drill and, starting from there, work with a jigsaw.
• The pots should now fit inside the squares.

Step 3: Hanging Holes

At the corners of the squares you need to make holes for the rope so that they can be hung. To do this use drill with a diameter of up to 1 cm.

Step 4: Paint the tree

Using sandpaper, remove roughness and unevenness that formed after sawing and drilling. Now the wood can be painted or simply treated with an antiseptic. In this case, dark brown paint was used.

Step 5: Paint the pots

Pots can also be painted, if desired. Casual strokes of white paint look good on plain clay pots. You can skip this step.

Step 6: Putting it all together

In order to fasten the wooden squares together, we need a thick rope: cut 4 ropes of 180 cm each (for the given number of tiers). Stretch one rope into each corner hole of one of the squares and tie a knot at the end, this will be the lower part of the structure.

Tie one more on each rope knot at 25-30 cm higher than the previous one and thread the ropes into the holes of the next square. Check that everything is level and the second tier is clearly horizontal above the first, adjust the knots if necessary. The second tier is ready. Repeat these steps with the remaining tiers.

Step 7: Plant the Plants

A practical advantage of such a hanging stand is that water that may flow down after watering from the top plant will drip onto the bottom one. So a stand for the pot is needed only on the lowest tier (if you use it outdoors, you can do without stands at all).

You can also place coffee filters or similar water-absorbing materials in the bottom of the pots, this way the water can drain out but the soil won't fall out through the hole.

TIP: To prevent the bottom pot from falling off the stand if someone accidentally snags the string, superglue it to the pot.

Step 8: Transplant the plants into prepared pots.

If you glue the base of the lower pot before inserting it into the wooden square, it will look like the photo below. If you want the bottom pot to be inserted into the tree in the same way as the others, then first replant the plants, insert the pots into the holes in the tree, and only then glue the stand to the bottom one.

Step 9: Hanging

1. To hang this structure, thread the ropes through a metal ring and tie a knot, or bend them over and tie another thin rope around them.
2. Adjust the rope so that all tiers are horizontal and level.

This stand is good, just don’t forget that the flowers need sufficient quantity Sveta.

A hanging stand is a wonderful solution for those who love flowers, but do not have enough space to display them.

Pot made of copper pipes

The manufacturing principle is similar to that described in the previous master class, only here copper tubes are used (and they are folded into a slightly different pattern). Of course, these materials will be more expensive than straws, and cutting them is not so fast, but in general there is no difficulty, and it turns out beautifully and with high quality.

TIP: If desired, the copper tubes can be replaced with plastic cocktail straws

Necessary materials:

• 2 m copper tube with a diameter of approximately 3 mm
• Mini pipe cutter
• Strong thread or fishing line
• Leather string (length depends on how high you want to hang the pot)
• small pot
• Plant

Step by step weaving:

Step 1: Cutting the tubes

You need to cut the tube into the following pieces: 20 pieces 4 cm long and 5 pieces 24 cm long. Cut the long pieces first, and then the small ones, it will be more convenient. Use a measuring tape for measurements.

Step 2: Start folding the tubes

Tie a knot at one end of the fishing line, and thread the other through 5 small pieces of tube so that you get a pentagon (that is, you need to pass the fishing line through the first piece of tube twice).

Step 3: Continue making pentagons from small tubes

• Thread the line through 4 tubes of the same size, and then through the tube of the previously formed pentagon. Now the fishing line is in the tube connecting the pentagons, and you need to bring it through the upper tubes of the newly obtained pentagon to its left edge.
• Don't worry if they don't look perfect, everything will straighten out when you hang and place the pot.
• Then do the same in the same way 2 more pentagons, there should be 4 pieces in total, and they should be located as in the photo below.
• Now bring the line through the tubes to the bottom of the outer pentagon and put the tube on it. Next, thread the line through one edge of the other outermost pentagon.

This is what you should get:

Pass the line through 2 more tubes, and then through the edge of the pentagon, as in the photo below. It should look like something like a flower, or rather like this:

Step 4: String Long Tubes

1. Bring the line to one of the highest points of the structure (between the two upper tubes of one of the pentagons). Now the fishing line needs to be threaded through a long tube.
2. Thread the line through another long tube, and then direct it to the next highest point of the pentagon structure (any one, not necessarily the adjacent one).

1. Thread the wire through the 2 small tubes to reach the next one top point. Now pass through another long tube, the line will come out to the junction of the long tubes, return the line back down through one of the previous two long tubes. Attach the fourth tube in the same way.
2. Now all you have to do is attach the last tube, but first place the pot in the middle of the structure, otherwise later it will not fit between the tubes.
3. Now attach the last tube. This is what you should get:

Step 5: Attach the leather lace

Cut about 30cm of leather cord and attach it to the connecting point of the long tubes. You can tie a knot, but here, for aesthetics, we used hot glue to secure the neatly folded end of the cord. This is what it looks like:

To prevent the gluing area from being visible, cut another small piece of cord, secure it with hot glue, and wrap it around the cord by which we will hang it.

Trim excess fishing line and cord. And the last step: plant your favorite indoor plants!

Where to hang the pots

Moreover, in the summer, plants can be placed both inside and outside the house, but since it’s cold now, we’ll focus on indoor ones. You can green any room in your apartment, kitchen or hallway, the main thing is to take into account the needs of the plants and the right amount of light. In fact, each version of a hanging planter can be placed in any room of the apartment, so it is only your design decision.

Of course, you can just put a flower pot on the windowsill or bedside table, and it will already look good. But if you try a little more, you can decorate appearance pots, and more optimally use the space of the apartment, at the same time arranging the plants and not taking up extra space with them (with hanging flower pots).

Above the workplace

Here, a hanging planter will not take up much space, especially since we always try to place the work table closer to the window, which will really appeal to indoor plants.

In the bedroom

Placing plants in the bedroom is not only beautiful, but also very useful. They enrich the room with oxygen. How nice it is to wake up among greenery. Try hanging a pot of plants in your bedroom.

In the kitchen

This perfect option, you will never snag or overturn a flowerpot. The flowerpot looks very homey in the kitchen!

On the balcony or in the chill-out area

If the area of ​​your apartment allows, then with the help of hanging flower pots, you can green up an entire room and make a mini-garden. But spruce does not have enough square footage - you can arrange a comfortable seating area on the balcony.

Pot ideas from scrap materials

If you show your imagination, you can make a hanging plant pot from absolutely any available materials. Starting from old cans, bottles to unnecessary towels and T-shirts.

From beads

If you have old beads lying around and you don’t know what to do with them, then here’s one option to solve the problem - decorate the pots.

From baskets and pots

Such pots can be used for a single pot or for several at once. Such wicker baskets will probably be found in many homes. They often lie idle, and in vain they will make an excellent hanging for flowers.

Flowerpots in high-tech style

Modern pendants made of concrete or brass will fit into modern style apartments.

From bottles

Probably the cheapest of all methods, but it looks no worse than the others. We collect empty plastic and glass bottles and make original flower pots.

From moss and shells

Many people at home have shells brought from the seas, and if you drill a small hole and plant small succulents there, you can create a mini-pots. The main thing is in quantity, 3-8 pieces will create an excellent hanging garden.

It’s difficult to imagine your favorite garden without flowers, since they are a stylish addition and an integral part landscape design. Compositions planted in unusual, original plant pots made by hand look especially impressive. Creating beautiful flower pots with your own hands from scrap materials is not only useful, but also a very exciting process. Step-by-step master class on making original flowerpots with detailed description And visual photo, later in our article.

What can you use to make a flowerpot with your own hands?

Today, specialized stores offer a wide range of various decor and garden decorations for every taste, including original flower pots. However, even with such an abundance of goods, it is not always possible to find what you need. There is only one way out of this situation - try to make a flowerpot yourself.

Oddly enough, the most unusual decorative flowerpots are made from ordinary material. You just need to be smart and give free rein to your wildest ideas and fantasies. Pots made from household items will look most harmonious in the garden. They are the ones who add real zest to your yard, creating the effect of grace and refined nobility.

Second life for old shoes

Surely at your dacha you have old shoes, which you haven’t worn for a long time, but you didn’t dare throw it away. The perfect way to breathe into her new life- make an original flower garden out of it.

To do this you will need an unnecessary pair of old shoes, the help of skillful hands and a little free time.

Step by step guide

1. Pour into the bottom of the shoe fertile soil(preferably black soil), then plant seeds or seedlings of your favorite plants in it;
2. Water the resulting decorative flower garden warm water and put it somewhere in visible side Houses;
3. To prevent excess moisture from accumulating inside, several small holes can be made in the sole;
4. To give the composition a more interesting look, the boots can be painted in any color you like.

Decorate your shoe with your favorite flowers and plants - great idea for the creative summer resident

Absolutely any shoes can be used as footwear: rubber boots, sneakers, sneakers, sandals, galoshes, low shoes, sandals, burkas. As for flowers, it is better to give preference to bright, unpretentious, low-growing plants.

Important! Pots made from old shoes should have holes to drain excess water. Otherwise, the roots may rot, which will lead to the death of the plants planted in them.

Flower pot made of cement, rags and burlap (photo)

A flower vase made of cement and rags looks very original and impressive. The method of making the product is quite simple and does not require special skills or tools. Enough to have on hand cement mortar And unnecessary waste textile production.

Important! Before drying, a rag soaked in liquid cement mortar can take any shape, so such compositions can be made in any form.

So, for work we need:

• Panels of rags of the required size. You can use torn burlap from cereal or sugar;
• Components for preparing concrete (water, cement, sifted sand or fine gravel);
• Patterns made to your taste. You can use ready-made ones, such as a bucket, pan, old vase, etc.

Step-by-step master class on making flower pots

1. Prepare according to the required proportions. To make it easier to work with the material, the solution should have the consistency of liquid sour cream;
2. Wrap a dry cloth around the pattern. If the size is appropriate, dip it in the solution and hold it there for about a minute;
3. Place a dampened rag over your workpiece and allow it to dry for 12 hours;
4. After completely dry remove the pattern. The flowerpot made of cement and rags is ready.

Good to know! The time for cement to set and harden in the sun is reduced to 2-3 hours.

If you don't like cold and grey colour concrete, or you are simply tired of it, dilute it with bright contrasting colors, so the flowerpot will look more elegant and fun.

Miniature garden made of tin cans (photo)

One of the most favorite materials for making flower pots is tin cans.

• Why are they so popular among those who love to create? Everything is very simple. Metal cans come in many colors, shapes and sizes, so you can use them to create a magnificent flower arrangement that will attract admiring glances.

The undeniable advantage of making such floral decorations is the minimum investment of effort and time while obtaining the most creative result.

To make a flowerpot from tin cans, usually the following materials are required for work:

• Cans;
• Nails and hammer;
• Colored acrylic paints, swing hand;
• Wooden base for fixing cans

Manufacturing Guide

1. To give the composition certain outlines, all jars are painted in bright colors;
2. After complete drying, a hole is made in the bottom of the jar to drain excess moisture;
3. All that remains is to secure the jars to the chosen base, pour soil into them and plant flowers.

To add more expressiveness to the product, you can apply patterns to the slightly dried surface or decorate it with a variety of buttons, ribbons, beads or beads.

Unnecessary teapot as a flower garden

Found in the garage old kettle? Don't rush to throw it away. You can make a beautiful decoration from it that will look original in your garden. In addition, creating crafts with your own hands will help not only realize your creative potential, but also save money.

A can of acrylic or aerosol paint will help restore the product to its original appearance. Using a stencil, you can also apply various patterns to the surface of the teapot.

Important! To prevent the paint from swelling over time, the surface must be well prepared before application.

A pot made from a teapot is mobile and, if necessary, can be moved to another place

• For those who don't want to bother with painting teapot, you can leave everything as is. A worn and tarnished metallic hue with light touch has its own special charm from time to time. The cold shine of polished metal looks no less advantageous.

Using an old teapot as a flowerpot is a rather bold and creative decision.

Vase made from improvised materials: step-by-step master class

Today, folk craftsmen and Hand Made craftsmen make original flowerpots with their own hands from almost any material that they can get their hands on. Ideas for creativity and inspiration can be drawn from anywhere, including the Internet.

The photos of beautiful flowerpots posted in our article once again prove that there are no limits to a person’s imagination. Innovative solutions and unusual super ideas allow you to create real works of art.

• If wooden sticks glue together into a hollow cube, so that each new row forms free space, and each subsequent one overlapped it, we get unusual flowerpot, which is perfect for small plants. You can place it anywhere, for example on a windowsill or hang it on a rope, after planting indoor flowers in it.

• Plastic bottles. Probably none garden craft or decoration cannot be done without their participation. Working with this material is very convenient and simple, the main thing is to take precautions. The simplest thing you can make from is a hanging flower pot.

However, use plastic bottles, it is possible not only in decorative purposes. You can plant seedlings in them vegetable crops, therefore this material is also a favorite among amateurs.

• You can weave a flowerpot with your own hands from ordinary rope. The shape of the product can be different: cylindrical, round or cone-shaped, the main thing is that the plant being planted fits freely into it. As a material for weaving, some craftsmen use thin vine branches or artificial rattan threads.

• If you approach the creation of decorative flower pot More thoroughly you can make a more interesting and large-scale composition. Hanging old unnecessary boiler over an improvised fire made of flowers and logs, you can get a very interesting result that will not remain without the close attention of your guests.

Important! To highlight and emphasize the beauty of the composition you have created, you can fence it with a border of ordinary stones, slightly drowning them in the ground.

Boxes for flowers and seedlings

• Summer residents are resourceful and thrifty people, so they never throw away anything, including cuttings from boards and other lumber. After all, they make excellent wooden boxes, which can be used as flower pots.

In order to make a flowerpot from boards, you can get by with minimal carpentry skills, and the only tools you need are a hacksaw, nails and a hammer.

• Good to know! Wooden boxes can also be used for planting seedlings different cultures. Only for this purpose, in the upper boards, it is advisable to make special holes for the hands so that they can be carried comfortably and safely.

Beautiful flower beds made from old things

Oddly enough, but old bike, which has not been driving for a long time, may still be useful to you as decorative decoration. There is no need to violate the integrity of the structure. Just use it as a living flower bed. Additional contrasting elements in the form of flowers and plants will turn an old bicycle into a real masterpiece of art.

Flower pots made from a bicycle - everything ingenious is simple

• By showing your imagination, you can get a unique hanging decoration with flowers from an ordinary bird cages. Just place a pot or container with low plants in it and decorate it with some decoration.

Important! A cage pot will look more elegant and noble if you use a decorative vintage cage in the Provence style.

• For craftsmen with golden hands, make decorative flowerpot for the garden with your own hands in the form of a cart will not be difficult. To do this, you will need a special tool and certain skills in handling wood and metal.
• To improve your mood and give yourself a lot of fun positive emotions, you can quickly and efficiently make flower pots from ordinary trash cans made of shiny metal. For ease of movement, rotating cranks can be attached to the bins. different sides furniture wheels.

As you can see, having at hand suitable material It’s very easy to make a flowerpot for your garden with your own hands. To make simple products, no skills are needed. Even a child can cope with this task. As for more complex products, you can’t do it without the help of adults.

The creative process of creating flowerpots is not only creative, but also educational. Therefore, even the youngest children can be involved in this exciting activity.