GOST door and window latches. Damn.8. Mortise screwdriver type ZR3

GOST 5090-86

Group Zh34

INTERSTATE STANDARD

LOCKING HARDWARE PRODUCTS FOR WOODEN WINDOWS AND DOORS

Types and main sizes

Locking fitting for wooden windows and doors. Types and basic dimensions

Date of introduction 1987-07-01

Resolution State Committee USSR Construction Affairs dated July 25, 1986 N 102, the date of introduction was set to 07/01/87

INSTEAD 5090-79*
________________
*Probably an error in the original. Should read: INSTEAD GOST 5090-79. - Database manufacturer's note.

REISSUE. November 2000

1. This standard applies to locking products for wooden windows and doors used in the construction of residential and public buildings.

2. The designation, name and recommended area of application of locking products are given in the table.

The main dimensions of locking products must correspond to those indicated in Figures 1-13.

The main dimensions of connectors, stops, handles and trims intended for completing transom fixtures or mortise screws must correspond to those specified in Appendix 1.

Examples of installation of transom devices, a connector for transoms with triple glazing and a mortise screw type ZR1 are given in Appendix 2.

3. Technical requirements, completeness, acceptance rules, control methods, labeling, packaging, transportation, storage and guarantee period operation of locking products must comply with GOST 538-88 and additional requirements of this standard.

4. Wrap-ties of type ZR1 were allowed to be manufactured until 01/01/90.


Type designation	Name		Drawing number
	Transom device	For transoms of public buildings with paired or separate sashes up to 1300 mm wide
	Transom device	For transoms of public buildings with paired or separate sashes up to 830 mm wide
	Espagnolette consignment note	For window sashes with a height of more than 1100 mm and balcony doors with paired or separate bindings and canvases
	Espagnolette consignment note	For window sashes with paired or separate sash heights up to 1100 mm inclusive
	Mortise bolt	For double doors
	Mortise tie wrap
	Mortise screwdriver
	Mortise screwdriver
	Mortise screwdriver	For casement windows and balcony doors
	Wrap invoice	For bathroom doors
	Wrap invoice	For window vents in residential buildings
	Overhead gate valve	For casement windows and balcony doors in residential and public buildings
		For windows and balcony doors with paired frames and leaves

Damn.1. Transom device type PF1

Transom device type PF1

Damn.1

Note. Size mm, where is the width of the transom taking into account the overlap.

Screws 1-4x30 according to GOST 1145-80 or according to GOST 1146-80 (4 pcs.).

Example symbol transom device for twin transoms:

PF1 GOST 5090-86

Same for separate transoms with connector version 1 and distance between transoms equal to 53 mm:

PF1-1-53 GOST 5090-86

Damn.2. Transom device type PF2

Transom device type PF2

1 - latch; 2 - frame; 3 - corner block; 4 - cord

Screws 1-4x30 according to GOST 1145-80 (12 pcs.).

An example of a symbol for a transom device for paired transoms with a limiter:

PF2 GOST 5090-86

The same, for separate transoms with connector version 1 and a distance between transoms equal to 53 mm:

PF2-1 - 53 GOST 5090-86

Damn.3. Consignment latch type ШН1

Consignment latch type ШН1

1 - locking plate; 2 - guide; 3 - bolt-bar; 4 - frame; 5 - pen; 6 - deadbolt

Note. Size +30 mm, where is the height of the sash or door leaf taking into account the float.

Screws 1-4x30 (16 pcs.) - for fastening the body and locking strips and 1-4x18 (12 pcs.) according to GOST 1145-80 or GOST 1146-80

ShN1 GOST 5090-86

Damn.4. Consignment latch type ShN2

Consignment latch type ShN2

1 - locking plate; 2 - guide; 3 - frame; 4 - pen

Damn.4

Note. Dimension +30 mm, where is the height of the sash, taking into account the overlap.

Screws 1-4x30 (8 pcs.) - for fastening the body and locking strips and 1-4x18 (8 pcs.) in accordance with GOST 1145-80 or GOST 1146-80 - for fastening the guides.

An example of a symbol for a latch:

ShN2 GOST 5090-86

Damn.5. Mortise bolt type ШВ

Mortise bolt type ШВ

Damn.5

Screws 1-4x30 according to GOST 1145-80 (5 pcs.).

An example of a symbol for a mortise latch:

ShV GOST 5090-86

Damn.6. Mortise screw-tie type ZR1

Mortise screw-tie type ZR1

Screws 1-4x25 or 1-3x25 according to GOST 1145-80 (2 pcs.) and pins (4 pcs.).

An example of a symbol for a tie wrap with a P1 type handle:

ZR1-1 GOST 5090-86

Damn.7. Mortise screwdriver type ZR2

Mortise screwdriver type ZR2

Damn.7

Screws 1-425 or 1-325 according to GOST 1145-80 (4 pcs.).

ZR2-1 GOST 5090-86

The same, with a P2 type handle and an overlay:

ZR2-2 GOST 5090-86

Damn.8. Mortise screwdriver type ZR3

Mortise screwdriver type ZR3

Damn.8

Screws 1-4x25 or 1-3x25 according to GOST 1145-80 (2 pcs.) and screws VM4-6g x 35.36 GOST 17474-80 (2 pcs.).

An example of a symbol for a screwdriver, version 1, right-hand version, with handle type P1:

ZR3 - 1-P-1 GOST 5090-86

The same, version 2, left version, with handle type P2 and overlay:

ZR3 - 2-L-2 GOST 5090-86

Damn.9. Mortise screwdriver type ZR4

Mortise screwdriver type ZR4

Damn.9

Note. The shape and dimensions of the bolt can be similar to the bolt of types ZR2, ZR3.

Screws 1-4x25 or 1-3x25 according to GOST 1145-80 (2 pcs.). and pins (2 pcs.).

Note. Holes with a diameter of 4.3 mm should be located on the axis of symmetry of the screwdriver body.

An example of a symbol for a screwdriver with a P1 type handle:

ZR4-1 GOST 5090-86

Damn 10. Invoice wrapping type ZF1

Invoice wrapping type ZF1

Screws 1-4x30 according to GOST 1145-80 or GOST 1146-80 (4 pcs.).

Note. It is allowed to place screws on the screw body within 45° from vertical axis.

An example of a symbol for a screwdriver with a striker plate version 1:

ZF1-1 GOST 5090-86

Damn 11. Invoice wrapping type ZF2

Invoice wrapping type ZF2

Screws 1-3x20 according to GOST 1145-80 or GOST 1146-80 (4 pcs.).

An example of a symbol for a right-hand wrap:

ZF2 P GOST 5090-86

The same, execution 2:

ZF2 P-2 GOST 5090-86

Damn.12. Overhead gate valve type ZT

Overhead gate valve type ZT

Screws 1-3x25 or 1-4x25 according to GOST 1145-80 (4 pcs.).

An example of a symbol for a gate valve with overlay:

ST(+15) GOST 5090-86

The same, without float:

ST() GOST 5090-86

Damn 13. Screed type ST

Screed type ST

Damn.13

Screw VM6-6g x 55.36 according to GOST 17473-80, GOST 17474-80 or GOST 17475-80.

Screws 1-3x25 according to GOST 1145 (2 pcs.).

An example of a screed symbol:

ST GOST 5090-86

5. ZR4 type screws are intended for completing windows and balcony doors manufactured on automated lines installed at woodworking plants before 01/01/86.

6. Bolts of mortise bolts and screws in open position should not protrude above the front surface of the strips or fall inside the body by more than 1 mm.

7. The dimensions of the bolt and locking strip of bolts of types ShN1, ShN2 and gate valves of type ZT must ensure an interference fit of at least 3 mm when connecting them. The thickness of the locking strips of these products should not be less than 1 mm.

8. The cord of a PF2 type transom fixture must move freely along the rollers, without jamming and not slip off them.

9. Wrapping types ZR1, ZR2, ZR4 and ZF1 should be made double-sided, types ZR3 and ZF2 - in right and left versions.

10. The bolt of the 3T type valve must be made of steel rod.

11. The shape of the handles, linings, the cross-section of the bolts of overhead latch bolts, as well as the pointed part of the pins for screwing, are not established by the standard.

12. Locking products must have a protective or protective-decorative coating in accordance with GOST 538-88 for 2, 3 or 4 (C) groups of operating conditions GOST 9.303-84.

13. Bolt-rods of overhead latches should be tested for strength during acceptance and type tests.

Tests are carried out on a bench by applying a force of 800 N (78.4 kgf) to a fixed bolt-rod for 1 minute at a distance of 5 mm from the attachment point perpendicular to the plane of the bolt attachment.

After testing, the latch bolt should not be deformed.

14. Transom devices of types PF1, PF2 and wrappings of types ZR1, ZR2, ZR3, ZR4 must be equipped with the following parts specified in Appendix 1:

- transom devices of types PF1, PF2, installed on transoms with separate frames, - with two connectors, design 1, 2, 3, 4 or 5 (drawing 1, 2, 3, 4, 5);

- transom devices of type PF2, installed on transoms with single or paired sashes, - two limiters (Fig. 7);

- transom devices of type PF2, installed on transoms with triple glazing, - two stops and two connectors (Fig. 6 and 7);

- screws of type ZR1 - with handles of type P1 (Fig. 8);

INTERSTATE COUNCIL FOR STANDARDIZATION, METROLOGY AND CERTIFICATION

INTERSTATE

STANDARD

HARDWARE PRODUCTS FOR WOODEN WINDOWS AND DOORS

Specifications

Official publication

Form standards

GOST 5090-2016

Preface

The goals, basic principles and basic procedure for carrying out work on interstate standardization are established in GOST 1.0-2015 “Interstate standardization system. Basic provisions" and GOST 1.2-2015 "Interstate standardization system. Interstate standards. rules and recommendations for interstate standardization. Rules for development, acceptance, updating and cancellation"

Standard information

1 DEVELOPED by the private institution “Certification Center for Window and Door Technology” (CSODT)

2 8NESSEN Technical Committee for Standardization TC 465 “Construction”

3 ADOPTED by the Interstate Council for Standardization, Metrology and Certification (protocol dated November 22, 2016 No. 93-P)

4 By Order of the Federal Agency for Technical Regulation and Metrology dated November 28, 2016 No. 1804-st, the interstate standard GOST 5090-2016 was put into effect as a national standard Russian Federation from July 1, 2017

5 83AMEN GOST 5087-60. GOST 5090-86. GOST 5091-78

Information about changes to this standard is published in the annual information index “National Standards”. and the text of the changes and amendments is in the monthly information index “National Standards”. In case of revision (replacement) or cancellation of this standard, the corresponding notice will be published in the monthly information index “National Standards”. Relevant information, notices and texts are also posted in information system for general use - on the official website of the Federal Agency for Technical Regulation and Metrology on the Internet ()

In the Russian Federation, this standard cannot be reproduced in whole or in part. replicated and distributed as an official publication without permission from the Federal Agency for Technical Regulation and Metrology

GOST 5090-2016

1 area of use............................................... ....1

3 Types and symbols...................................................2

4 Technical requirements................................................... .3

4.1 Design requirements...................................................3

4.2 Strength requirements.................................................... 3

4.3 Requirements operational characteristics.............................4

4.4 Requirements for the quality of protective*decorative (protective) coatings................................4

4.5 Requirements for materials...................................................4

4.6 Completeness................................................... ....5

4.7 Marking................................................... ......5

4.8 Packaging................................................... ........5

5 Acceptance rules......................................................... ......5

6 Test methods................................................................... .....6

7 Transportation and storage...................................................6

8 Manufacturer's warranty................................................................... ..7

Appendix A (informative) Designs of hardware....................................8

Appendix B (informative) Components for transom fixtures..................................22

Appendix B (for reference) Examples of installation of transom devices.................................25

GOST 5090-2016

INTERSTATE STANDARD

HARDWARE PRODUCTS FOR WOODEN WINDOWS AND DOORS Technical specifications

Locking fitting for wooden windows end doors. Specifications

Introduction date - 2017-07-01

1 area of use

This standard applies to locking, fixing and auxiliary hardware for wooden windows and doors used in the construction of residential and public buildings, and establishes requirements for design, performance and strength characteristics. acceptance rules and control methods.

8 of this standard uses regulatory references to the following interstate standards:

GOST2.601-2006 Unified system of design documentation. Operational documents GOST 9.014-78 Unified system of protection against corrosion and aging. Temporary anti-corrosion protection of products. General requirements

GOST 9.303-84 Unified system of protection against corrosion and aging. Metallic and non-metallic inorganic coatings. General requirements for selection

GOST 9.308-85 Unified system of protection against corrosion and aging. Metallic and non-metallic inorganic coatings. Accelerated corrosion test methods

GOST 538-2014 Lock and hardware products. General technical conditions

GOST 1145-80 Screws with a countersunk head. Design and dimensions

GOST 1146-80 Screws with a lolulot head. Design and dimensions

GOST9012-59 (IS0410-82. ISO 6506-81)Metals. LoBrinell hardness measurement method

GOST 10354-82 Polyethylene film. Specifications

GOST 12301 -2006 Boxes made of cardboard, paper and combined materials. General technical conditions

GOST 12303-80 Packs made of cardboard, paper and combined materials. General technical conditions

GOST 15150-69 Machines, instruments and others technical products. Versions for different climatic regions. Categories, operating, storage and transportation conditions regarding the impact of environmental climatic factors

GOST 17474-80 Countersunk head screws of accuracy classes A and B. Design and dimensions GOST 17475-80 Countersunk head screws of accuracy classes A and B. Design and dimensions

Official publication

GOST 5090-2016

GOST 16242-72* Statistical acceptance control based on an alternative criterion. Control plans

GOST 24033-60 Wooden windows and balcony doors. Mechanical Test Methods

GOST 25951 -83 Polyethylene shrink film. Specifications

Note - When using this standard, it is advisable to check the validity of the reference standards in the public information system - on the official website of the Federal Agency for Technical Regulation and Metrology on the Internet or using the annual information index “National Standards”, which was published as of January 1 of the current year, and on issues of the monthly information index “National Standards” for this year. If the reference standard is replaced (changed), then when using this standard you should be guided by the replacing (changed) standard. If the reference standard is canceled without replacement, then the provision in which a reference is made to it is applied in the part that does not affect the reference.

3 Types and symbols

Table 1

fork products	Conditional	No er figure
Transom device		For transoms of public buildings with paired or separate sashes up to 1300 mm wide
		For transoms of public buildings with paired or separate sashes up to 830 mm wide
Shling invoice-		For window sashes over 1100 mm high and balcony doors
		with paired or separate bindings and canvases
		For window sashes with paired or separate sashes with a height of more than 1100 mm inclusive
mortise screw		For casement windows and balcony doors
Overlay wrap		For bathroom doors
		For window vents in residential buildings
Invoice		For casements of windows and balcony doors of residential and public buildings

		For windows and balcony doors with paired frames and
		canvases
Retainer		For windows with paired sashes
		For windows with separate sashes
Peephole		For entrance doors to apartments
door chain		For entrance doors to apartments
Door stop		For doors
Window stop		For windows with split sashes
Square
		For fastening tenon joints

* In the Russian Federation, GOST R ISO 2859-1-2007 is in force. Statistical methods. Alternative sampling procedures. Part 1: Sampling plans for successive lots based on acceptable quality levels.”

GOST 5090-2016

End of table 1

product type	Conditional
Handles		For windows and balcony doors of residential buildings
		For windows and internal doors buildings
		For entrance doors to apartments and internal doors and windows of public buildings
	RS200. RS250. PC300. PC400. RS500. PC 600	For entrance doors to buildings
Knobs-buttons		For interior doors of residential buildings and bathroom doors
		For internal doors of residential buildings

3.2 Designs and main dimensions of hardware for various purposes are shown in Figures A.1-A.21 of Appendix A.

3.3 The main dimensions of connectors, stops, handles and trims intended for completing transom devices and mortise screws are indicated in Appendix B.

Examples of installation of transom devices and a connector for transoms with triple glazing are given in Appendix B.

4 Technical requirements

4.1 Design requirements

4.1.1 Products must comply with the requirements of GOST 538. of this standard and the sample standard approved in the manner established at the enterprise.

4.1.2 Products must be manufactured according to design documentation developed taking into account the requirements of this standard.

4.1.3 This standard does not establish the shape of handles, linings, the cross-section of the bolts of overhead bolts, as well as the pointed part of the pins for screws.

4.1.4 The cord of a PF2 type transom device must pass over the rollers freely, without jamming and not jumping off.

4.1.5 The bolts of mortise latches and bolts in the open position should not protrude above the front surface of the slats or fall inside the body by more than 1 mm.

4.1.6 Dimensions of bolts and locking strips of overhead latches of types ШН1. ШН2 and surface-mounted valves ЗТ must ensure an interference tension of at least 3 mm when connecting them. The thickness of the locking strips of these products must be at least 1 mm.

4.1.7 Wrappers of type ZF1 should be made double-sided, types ZRZ and ZF2 - right and left-handed.

4.1.8 The design of the latches should provide for the possibility of installing them on both right and left window sashes.

4.1.9 The viewing angle of the door peephole must be at least 120 degrees.

4.1.11 The design of detachable connections of products must exclude the possibility of their spontaneous separation after installation on window and door units.

4.1.12 Moving parts of products, depending on their purpose, must be fixed in the outermost positions. if necessary, in intermediate positions.

4.1.13 The design of products must provide them reliable fastening throughout the entire service life.

4.2 Strength requirements

4.2.1 The strength of hardware products is characterized by resistance to static, dynamic or impact loads. Products whose operation is associated with the need to bear loads are tested for resistance to the specified loads.

GOST 5090-2016

4.2.2 The bolt-rods of overhead latches must be strong and withstand a load P = 800N.

4.2.3 Door chains must be strong and withstand a tensile force of 1960 N.

4.2.4 Handle brackets must be strong enough to withstand the following loads:

Along the handle-bracket parallel to the plane of its fastening (Table 2);

Perpendicular to the axis of the handle-bracket (Table 3).

Table 2 - Strength of handle-brackets under load along the axis of the handle-bracket parallel to the plane of its fastening

’ e is the width of the load application area e of the average size of the handle-brace.

4.2.5 Handle-buttons of types RK1 and RK2 must be durable under the action of the loads given in Table 4.

Table 4 - Strength of handle-buttons under loads

4.3 Performance requirements

4.3.1 Performance values are set in project documentation taking into account the efforts made by a person for the operation of products, as well as depending on the purpose and area of application of the products.

4.3.2 Moving parts of products must move without jamming.

4.4 Requirements for the quality of protective and decorative (protective) coatings

Hardware must have protective or protective-decorative coatings in accordance with GOST 538, depending on the groups of operating conditions 1-Evil GOST 9.303. taking into account the scope of their application, climatic versions U. UHL. TV. TS. TM and placement categories 2-4 according to GOST 15150.

4.5 Material requirements

4.5.1 For the manufacture of hardware parts, use following materials: steel, aluminum alloys, copper alloys, plastics, glass regulatory documents(ND). approved in accordance with the established procedure.

GOST 5090-2016

4.5.2 Pins must be made of zinc-aluminum or other alloys with a hardness of 50...90H8.

4.5.3 The invoice for the gate valve type ZT must be made of steel rod.

4.6 Completeness

4.6.1 Each product must be supplied complete in accordance with the requirements of the RD for products specific types, design documentation and contracts.

4.6.2 Hardware, taking into account functional features should be equipped with screws in accordance with GOST 1145. GOST 1146 or screws in accordance with GOST 17474 and GOST 17475.

4.6.3 Hardware must be provided with a label (if necessary, a passport) in accordance with GOST 2.601. as well as (if necessary) instructions for operation and installation (installation).

4.7 Marking

4.7.1 Each product must be marked with the manufacturer’s trademark and design option. The location of marking is indicated in the working drawings.

4.7.2 The consumer packaging must indicate:

Name, address, trademark of the manufacturer;

Name and symbol of the product;

Number of products in the container;

Stamp of the technical control service;

Packer number, packing date (month, year);

Coating corrosion resistance class.

4.8 Packaging

4.8.1 Products must be stored and transported in packaged form.

4.8.2 Products of the same type must be packaged in consumer packaging and then in transport packaging. The method of packaging products must prevent their spontaneous movement and ensure the safety of products with their components and fasteners.

4.8.4 For packaging handles, fasteners, latches, mortise bolts, door and window stops, couplers, angles, it is allowed to use UM-1 packaging material in accordance with GOST 9.014. Fasteners must be wrapped and bundled with the products.

4.8.5 A packing list containing information according to 4.7.2 of this standard is included in each package. Individual packaging may include a label containing the same information.

5 Acceptance rules

5.1 Products must be accepted by the technical control service of the manufacturer for compliance with the requirements of this standard, as well as additional requirements specified in the contract for the supply of products.

5.2 Quality finished products confirm:

Incoming inspection of materials and components;

Production operational control;

Shift acceptance control of finished products;

Acceptance tests of a batch of products carried out by the technical control service of the manufacturer;

Periodic testing.

5.3 Procedure input control materials and components are established in the technological documentation taking into account the requirements of the RD for these materials and components.

5.4 The quality of manufacturing of product parts during the production process is confirmed by conducting production operational control at all stages of the technological cycle.

5.5 Acceptance quality control of finished products with a batch size of 90 pcs. inclusively carried out by the method of continuous control (piece by piece). With a batch size of 91 pcs. and more acceptance inspection should be carried out in accordance with GOST 18242. Product acceptance inspection plan - in accordance with GOST 538.

GOST 5090-2016

5.6 Acceptance tests of each batch of finished products are carried out by the technical control service of the manufacturer. The procedure for conducting acceptance tests is established in the quality control systems of the manufacturer.

5.7 Periodic tests

5.7.1 Periodic tests of wraps, door chains, transom devices must be carried out at least once every three years. During periodic testing, products are checked within the scope of acceptance control for compliance with the requirements of 4.2 and 4.3 of this standard and the requirements of ND for products of specific types.

5.7.2 At least three products are selected for periodic testing. If at least one product fails the test, double the number of tests should be carried out. If the results of repeated tests are unsatisfactory, the products are considered to have failed periodic testing. The batch of products is rejected.

5.7.3 Qualification tests are carried out for all indicators in accordance with the requirements of this standard and ND for products of specific types when putting the product into production.

5.7.4 Testing of products for certification purposes (if necessary) is carried out within the scope of periodic testing.

5.7.5 If changes are made to the design, materials or manufacturing technology, type tests of products are carried out to assess the effectiveness and feasibility of the changes made. The scope of type tests is determined by the nature of the changes. Products that have passed acceptance control are subjected to standard tests.

5.7.6 After the expiration of the warranty period of storage of products, the packaging, labeling, completeness, and appearance are checked. absence or presence of corrosion, operability.

6 Test methods

6.1 Methods for testing products during shift acceptance inspection and acceptance testing of batches of products carried out by the technical control service of the manufacturer are established in the RD for specific types of products.

6.2 Dimensions are checked universally measuring instrument. Appearance and the color of the products is checked visually by comparison with a reference sample. The operation of moving parts is checked manually, performing product operation cycles at least five times.

6.3 Testing of products in terms of strength and performance characteristics is carried out according to the methods of testing laboratories, taking into account the requirements of this standard and in accordance with GOST 24033.

6.4 All strength tests are carried out according to the following scheme: the applied loads are brought to the standard ones and left applied for 1 minute. After removing the loads, the condition of the test sample is visually checked.

6.5 When testing the strength of bolts-rods of overhead bolts, a load of 600 N is applied at a distance of 5 mm from the fastening point perpendicular to the plane of installation of the bolt.

6.6 When testing the strength of handle-brackets and handle-buttons, depending on the type and type of handle, the loads given in Tables 2-4 are applied.

6.7 The corrosion resistance of coatings is tested in special chambers in a neutral fog of 5% NaCI in accordance with GOST 9.306 and the working methods of testing laboratories. Evaluation of test results - in accordance with GOST 536. Tests for corrosion resistance of coatings must be carried out on the product in assembled form or on its individual parts.

6.6 Completeness, packaging and labeling are checked visually for compliance with the requirements of the design documentation.

7 Transportation and storage

7.1 Products are transported by all types of transport in covered vehicles in accordance with the rules and conditions for loading and securing cargo in force for the corresponding type of transport.

7.2 Storage conditions for products - according to group 2. Transportation conditions - according to group 5. established by GOST 15150.

GOST 5090-2016

8 Manufacturer's warranty

8.1 The manufacturer must guarantee compliance of products with the requirements of this standard and ND for products of specific types, subject to the conditions of transportation, storage and operation, as well as subject to the presence of a single marking of the manufacturer’s trademark on the main parts of products supplied to the market as a whole product or as a set of individual parts.

8.2 Warranty period - no less than May 24 from the date of start of operation or from the date of sale through the retail chain.

8.3 Guaranteed shelf life is one year from the date of manufacture.

8.4 In case of delivery of products after the end of the warranty storage period, the products must be checked by the manufacturer (supplier) or consumer.

GOST 5090-2016

Appendix A (reference)

Hardware designs

Application - Dimension L (h * 13) mm, where B is the width of the transom taking into account the overlap.

An example of a symbol for a transom device for transoms with paired overpayments:

PF1 GOST 5090-2016

The same for transoms with separate covers with a connector and a distance between transoms of 53 mm:

PF1-1-53 GOST 5090-2016

Figure A. 1 - Transom device type PF1

GOST 5090-2016

) - latch: 2 - body: 3 - corner block: 4 - cord

An example of a symbol for a fanlight device for paired fanlights with a limiter:

PF2GOST5090- 20f$

Figure A.2 - LF2 type transom device

GOST 5090-2016

Example of latch symbols;

ShN1 GOST 5000-2016

Figure A.Z - Overhead latch type ShN1

GOST 5090-2016

Note - Size S w (H* 30) mm. where H is the height of the sash, taking into account the overlap.

An example of a symbol for a latch:

ShN2 GOST 5090-2016

Figure A.4 - Shn2 type overhead latch

GOST 5090-2016

Shut-off Version 1 (right opening)

Version 2 (left opening)

An example of symbols for a screwdriver version 1 (right) with handle P1 style

ZRZ-1-P-R1 GOST 5090-2016 The same version 2 (left) with handle type P2 and escutcheon:

ZRZ-2-L-R2 GOST 5090-2016

Figure A.5 - Mortise screw type ZRZ

12 min, ii i12max 50 max

GOST 5090-2016

Striker plates

Execution 1 Execution 2

An example of a symbol for a sealed screw type ZF1 with a shut-off valve, version 1.

I like

STATE STANDARD OF THE USSR UNION

LOCKING HARDWARE PRODUCTS FOR WOODEN WINDOWS AND DOORS TYPES AND MAIN DIMENSIONS

Locking fittings for wooden windows and doors.
Types and basic dimensions

GOST 5090-86

Group Zh34

1. This standard applies to locking products for wooden windows and doors used in the construction of residential and public buildings.

Drawing 1. Transom device type PF1
	Note. Dimension L = B + 13 mm, where B is the width of the transom taking into account the overlap. Screws 1 - 4 x 30 according to GOST 1145-80 or according to GOST 1146-80 (4 pcs.). An example of a symbol for a transom device for paired transoms: PF1 GOST 5090-86 PF1-1-53 GOST 5090-86.
Drawing 2. Transom device type PF2
	1 - latch; 2 - body; 3 - corner block; 4 - cord Screws 1 - 4 x 30 according to GOST 1145-80 (12 pcs.). An example of a symbol for a transom device for paired transoms with a limiter: PF2 GOST 5090-86 The same, for separate transoms with connector version 1 and a distance between transoms equal to 53 mm: PF2-1-53 GOST 5090-86
Drawing 3. Shn1 type consignment latch
	1 - locking plate; 2 - guide; 3 - bolt-bar; 4 - body; 5 - handle; 6 - deadbolt. Note. Dimension L = H + 30 mm, where H is the height of the sash or door leaf, taking into account the overlap. Screws 1 - 4 x 30 (16 pcs.) - for fastening the body and locking strips and 1 - 4 x 18 (12 pcs.) in accordance with GOST 1145-80 or GOST 1146-80 - for fastening the guides. ShN1 GOST 5090-86
Drawing 4. Shn2 type consignment latch
	Note. Dimension L = H + 30 mm, where H is the height of the sash, taking into account the overlap. Screws 1 - 4 x 30 (8 pcs.) - for fastening the body and locking strips and 1 - 4 x 18 (8 pcs.) according to GOST 1145-80 or GOST 1146-80 - for fastening the guides. An example of a symbol for a latch: ShN2 GOST 5090-86
Drawing 5. Mortise bolt type ШВ
	Screws 1 - 4 x 30 according to GOST 1145-80 (5 pcs.). An example of a symbol for a mortise latch: ShV GOST 5090-86
Drawing 6. Mortise tie wrap type ZR1
	Screws 1 - 4 x 25 or 1 - 3 x 25 according to GOST 1145-80 (2 pcs.) and pins (4 pcs.). An example of a symbol for a tie wrap with a P1 type handle: ZR1-1 GOST 5090-86
Drawing 7. Mortise screwdriver type ZR2
	Screws 1 - 4 x 25 or 1 - 3 x 25 according to GOST 1145-80 (4 pcs.). ZR2-1 GOST 5090-86 The same, with a P2 type handle and an overlay: ZR2-2 GOST 5090-86
Drawing 8. Mortise screwdriver type ZR3
	Screws 1 - 4 x 25 or 1 - 3 x 25 according to GOST 1145-80 (2 pcs.) and screws VM4 - 6g x 35.36 GOST 17474-80 (2 pcs.). An example of a symbol for a screwdriver, version 1, right-hand version, with handle type P1: ZR3-1-P-1 GOST 5090-86 The same, version 2, left version, with handle type P2 and overlay: ZR3-2-L-2 GOST 5090-86
Drawing 9. Mortise screwdriver type ZR4
	Note. The shape and dimensions of the bolt can be similar to the bolt of types ZR2, ZR3. Screws 1 - 4 x 25 or 1 - 3 x 25 according to GOST 1145-80 (2 pcs.) and pins (2 pcs.). Note. Holes with a diameter of 4.3 mm should be located on the axis of symmetry of the screwdriver body. An example of a symbol for a screwdriver with a P1 type handle: ZR4-1 GOST 5090-86
Drawing 10. Invoice wrapping type ZF1
	Screws 1 - 4 x 30 according to GOST 1145-80 or GOST 1146-80 (4 pcs.). Note. It is allowed to place screws on the screw body within 45° from the vertical axis. An example of a symbol for a screwdriver with a striker plate version 1: ZF1-1 GOST 5090-86
Drawing 11. Invoice wrapping type ZF2
	Screws 1 - 3 x 20 according to GOST 1145-80 or GOST 1146-80 (4 pcs.). An example of a symbol for a right-hand wrap: ZF2 P GOST 5090-86 The same, execution 2: ZF2 P-2 GOST 5090-86
Drawing 12. Overhead gate valve type ZT
	Screws 1 - 3 x 25 or 1 - 4 x 25 according to GOST 1145-80 (4 pcs.). An example of a symbol for a gate valve with overlay: ZT (h + 15) GOST 5090-86 The same, without float: ZT (h) GOST 5090-86
Drawing 13. Screed type ST
	Screw VM6 - 6g x 55.36 according to GOST 17473-80, GOST 17474-80 or GOST 17475-80. Screws 1 - 3 x 25 according to GOST 1145-80 (2 pcs.).

The main dimensions of connectors, stops, handles and trims intended for completing transom fixtures or mortise screws must correspond to those specified in Appendix 1.

Examples of installation of transom fixtures, a connector for transoms with triple glazing and a mortise screw type ZR1 are given in Appendix 2.

3. Technical requirements, completeness, acceptance rules, control methods, labeling, packaging, transportation, storage and warranty period of operation of locking products must comply with GOST 538-88 and additional requirements of this standard.

4. Wrap-ties of type ZR1 may be manufactured before 01/01/90.

An example of a screed symbol:
ST GOST 5090-86

5. ZR4 type screws are intended for completing windows and balcony doors manufactured on automated lines installed at woodworking plants before 01/01/86.

6. The bolts of mortise latches and screws in the open position should not protrude above the front surface of the slats or fall inside the body by more than 1 mm.

8. The cord of a PF2 type transom fixture must move freely along the rollers, without jamming and not slip off them.

9. Wrapping types ZR1, ZR2, ZR4 and ZF1 should be made double-sided, types ZR3 and ZF2 - in right and left versions.

10. The bolt of the 3T type valve must be made of steel rod.

11. The shape of the handles, linings, cross-section of the bolts of overhead latch bolts, as well as the pointed part of the pins for screws is not established by the standard.

12. Locking products must have a protective or protective-decorative coating in accordance with GOST 538-88 for 2, 3 or 4 (C) groups of operating conditions of GOST 9.303-84.

13. Bolt-rods of overhead latches should be tested for strength during acceptance and type tests.

Tests are carried out on a bench by applying a force of 800 N (78.4 kgf) to a fixed bolt-rod for 1 minute at a distance of 5 mm from the attachment point perpendicular to the plane of the bolt attachment.

After testing, the bolt-bar should not be deformed.

14. Transom devices of types PF1, PF2 and wrappers of types ZR1, ZR2, ZR3, ZR4 must be equipped with the following parts specified in Appendix 1:
- transom devices of types PF1, PF2, installed on transoms with separate frames, - with two connectors of design 1, 2, 3, 4 or 5 (drawings 1, 2, 3, 4, 5);
- transom devices of type PF2, installed on transoms with single or paired sashes, - two stops (Fig. 7);
- transom devices of type PF2, installed on transoms with triple glazing, - two stops and two connectors (Fig. 6 and 7);
- screws of type ZR1 - with handles of type P1 (Fig. 8);
- wrappings of types ZR2, ZR3, ZR4 - with handles of type P1 or P2 with overlays. The number of P2 type handles and escutcheons must be specified when ordering. Feedback Auto RU

Price 5 kopecks

STATE STANDARD OF THE USSR UNION

TYPES AND MAIN SIZES

GOST 5090-79

Official publication

USSR STATE COMMITTEE FOR CONSTRUCTION AFFAIRS Moscow

STANDARD

STATE

USSR UNION

LOCKING DEVICES FOR WINDOWS AND DOORS

TYPES AND MAIN SIZES

GOST 5090-79

Official publication

Page 8 GOST 5890-79

Mortise bolt type NTV

Screws A4X30 according to GOST 1145-70 (5 pcs.).

An example of a symbol for a mortise latch:

ShV GOST 5090-79

DEVELOPED

Ministry of Industry building materials USSR State Committee for Civil Engineering and Architecture under the USSR State Construction Committee

PERFORMERS

N. D. Popkov (topic leader), V. A. Bondareva, N. G. Korolev, A. A. Zuev

INTRODUCED by the USSR Ministry of Construction Materials Industry

Deputy Minister N.P. Kabanov

APPROVED AND ENTERED INTO EFFECT by Resolution of the USSR State Committee for Construction Affairs dated March 30, 1979 No. 47

UDC 683.35/37:006.354 Group Zh34

STATE STANDARD OF THE UNION OF THE USSR

LOCKING DEVICES FOR WINDOWS AND DOORS

Types and main sizes

Locking window and door fittings.

Types and principal dimensions

Instead of GOST 5090-73

By Decree of the USSR State Committee for Construction Affairs dated March 30, 1979 No. 47, the introduction date was established

from 01.01. 1980

Failure to comply with the standard is punishable by law

1. This standard applies to locking devices for wooden windows and doors used in the mass construction of residential and public buildings.

2. Symbols of types and names of locking devices, the recommended scope of their application are given in the table.

The types and main dimensions of locking devices must correspond to those indicated in the drawing. 1-13.

The main dimensions of connectors, stops, handles and linings intended for completing transom fixtures and mortise fittings, respectively, must correspond to those indicated in the drawing. 1-7 given in mandatory Appendix 1 to this standard.

Examples of installation of transom devices of types PF1 and PF2. tilt-and-turn device and mortise screw type ZR1 are given in recommended Appendix 2 to this standard.

Transom device

Tilt-and-turn device

Espagnolette consignment note

Mortise espagnolette Mortise fastener

Mortise screwdriver

Overhead screws Overhead screws Overhead bolts Screed

For transoms of public buildings with paired or separate sashes up to 1300 mm wide For transoms of public buildings with paired or separate sashes up to 830 mm wide For casement windows with paired sashes up to 400 mm wide

For casements of windows with a height of more than 1100 mm and balcony doors with paired or separate sashes and leaves For sashes of windows with paired or separate sashes with a height of up to 1100 mm inclusive For double-leaf doors

For windows and balcony doors with paired frames and leaves

For casement windows and balcony doors Same

For bathroom doors

For vents in production repair work For window sashes of residential buildings during renovation work For windows and balcony doors with paired frames and leaves

GOST 5090-79 Page 3

Transom device type PF1

Note. Dimension L=B+70 mm, where B is the width of the transom taking into account the overlap

Screws A4X30 according to GOST 1145-70 or according to GOST 1146-70 (22 pcs.).

An example of a symbol for a transom device for paired transoms:

PF1 GOST 5090-79

PF1-1-53 GOST 5090-79

Transom device type PF2

latch; 2-body; 3-block corner; 4-cord.

Screws A4X30 according to GOST 1145-70 (10 pcs).

An example of a symbol for a transom device for paired transoms with a limiter:

PF2 GOST 5090-79

The same, for separate transoms with connector version 1 with a distance between transoms equal to 53 mm:

PF2-1-53 GOST 5090-79

GOST 5090-79 Page 5

Tilt and turn device type UP

horizontal hinge; 2-angular support; a-hinge vertical

Screws A4X30 according to GOST 1145-70 (15 pcs.).

An example of a symbol for a right-hand tilt and turn device:

UP-P GOST 5090-79

Page 6 GOST 5090-79

Consignment latch type ШН1

Locking plate version 2 Y

shut-off

Note. Size £=#+30 mm, where H is the height of the sash or door leaf, taking into account the overlap

Screws A4X30 according to GOST 1145-70 or according to GOST 1146-70 (20 pcs.).

Type of designation for a latch with a locking plate, version 1:

ШН1-1 GOST 5090-79 The same, with locking plate version 2:

ShN1-2 GOST 5090-79

GOST 5090-79 Page 7

Consignment latch type ShN2

Locking plate version 1

L/wjma shut-off

version 1

Note. Size 1-I+30 we, where I is the height of the sash, taking into account the overlap.

Screws A4X30 according to GOST 1145-70 or according to GOST 1146-70 (16 pcs.).

An example of a symbol for a latch with a perky bar, version 1:

ShN2-1 GOST 5096-79

The same, with striker plate design 2-

ShN2-2 GOST 5090-79

/ GOST 5090-86 Hardware locking products for wooden windows and doors. Types and main sizes.

Updated: 02/09/2006

GOST 5090-86

Group Zh34

STATE STANDARD OF THE USSR UNION

LOCKING HARDWARE PRODUCTS
FOR WOODEN WINDOWS AND DOORS

Types and main sizes

locking fitting for wooden windows and doors.

types and basic dimensions

Date of introduction 1987-07-01

APPROVED AND ENTERED INTO EFFECT by Resolution of the USSR State Committee for Construction Affairs dated July 25, 1986 No. 102

5. REISSUE

1. This standard applies to locking products for wooden windows and doors used in the construction of residential and public buildings.

The main dimensions of locking products must correspond to those indicated in the drawing. 1-13.

The main dimensions of connectors, stops, handles and trims intended for completing transom fixtures or mortise screws must correspond to those specified in Appendix 1.

Examples of installation of transom devices, a connector for transoms with triple glazing and a mortise screw type ZR1 are given in Appendix 2.

4. Wrap-ties of type ZR1 may be manufactured before 01/01/90.

5. ZR4 type screws are intended for completing windows and balcony doors manufactured on automated lines installed at woodworking plants before 01/01/86.

Type designation	Name		Drawing number
	Transom device	For transoms of public buildings with paired or separate sashes up to 1300 mm wide
	Transom device	For transoms of public buildings with paired or separate sashes up to 830 mm wide
	Espagnolette consignment note	For window sashes with a height of more than 1100 mm and balcony doors with paired or separate sashes and leaves
	Espagnolette consignment note	For window sashes with paired or separate sash heights up to 1100 mm inclusive
	Mortise bolt	For double doors
	Screw - mortise tie
	Mortise screwdriver	For casement windows and balcony doors
	Mortise screwdriver
	Mortise screwdriver
	Wrap invoice	For bathroom doors
	Wrap invoice	For window vents in residential buildings
	Overhead gate valve	For casement windows and balcony doors in residential and public buildings
		For windows and balcony doors with paired frames and leaves

Transom device type PF1

Note. Size +13 mm, where is the width of the transom taking into account the overlap.

Screws 1-4x30 according to GOST 1145-80 or according to GOST 1146-80 (4 pcs.).

An example of a symbol for a transom device for paired transoms:

PF1 GOST 5090-86

The same, for separate transoms with connector version 1 and a distance between transoms equal to 53 mm:

PF1-1-53 GOST 5090-86

Transom device type PF2

1 - latch; 2 - body; 3 - corner block; 4 - cord

Screws 1-4x30 according to GOST 1145-80 (12 pcs.).

An example of a symbol for a transom device for paired transoms with a limiter:

PF2 GOST 5090-86

The same, for separate transoms with connector version 1 and a distance between transoms equal to 53 mm:

PF2-1 - 53 GOST 5090-86

Consignment latch type ШН1

Note. Size +30 mm, where is the height of the leaf or door leaf, taking into account the overlap.

Screws 1-4x30 (16 pcs.) - for fastening the body and locking strips and 1-4x18 (12 pcs.) in accordance with GOST 1145-80 or GOST 1146-80 - for fastening the guides.

An example of a symbol for a latch.

ShN1 GOST 5090-86

Consignment latch type ShN2

Note. Dimension +30 mm, where is the height of the sash, taking into account the overlap.

Screws 1-4x30 (8 pcs.) - for fastening the body and locking strips and 1-4x18 (8 pcs.) in accordance with GOST 1145-80 or GOST 1146-80 - for fastening the guides.

An example of a symbol for a latch:

ShN2 GOST 5090-86

Mortise bolt type ШВ

Screws 1-4x30 according to GOST 1145-80 (5 pcs.).

An example of a symbol for a mortise latch:

ShV GOST 5090-86

Mortise screw-tie type ZR1

Screws 1-4x25 or 1-3x25 according to GOST 1145-80 (2 pcs.) and pins (4 pcs.).

An example of a symbol for a tie wrap with a P1 type handle:

ZR1-1 GOST 5090-86

Mortise screwdriver type ZR2

Screws 1-4 25 or 1-3 25 according to GOST 1145-80 (4 pcs.).

ZR2-1 GOST 5090-86

The same, with a P2 type handle and an overlay:

ZR2-2 GOST 5090-86

Mortise screwdriver type ZR3

Striker plate Version 1

Version 2

The rest -

see version 1

Screws 1-4x25 or 1-3x25 according to GOST 1145-80 (2 pcs.) and screws VM4-6g x 35.36 GOST 17474-80 (2 pcs.).

An example of a symbol for a screwdriver, version 1, right-hand version, with handle type P1:

ZR3 - 1-P-1 GOST 5090-86

The same, version 2, left version, with handle type P2 and overlay:

ZR3 - 2-L-2 GOST 5090-86

Mortise screwdriver type ZR4

Note. The shape and dimensions of the bolt can be similar to the bolt of types ZR2, ZR3.

Screws 1-4x25 or 1-3x25 according to GOST 1145-80 (2 pcs.). and pins (2 pcs.).

Note. Holes with a diameter of 4.3 mm should be located on the axis of symmetry of the screwdriver body.

An example of a symbol for a screwdriver with a P1 type handle:

ZR4-1 GOST 5090-86

Invoice wrapping type ZF1

Screws 1-4x30 according to GOST 1145-80 or GOST 1146-80 (4 pcs.).

Note. It is allowed to place screws on the screw body within 45° from the vertical axis.

An example of a symbol for a screwdriver with a striker plate version 1:

ZF1-1 GOST 5090-86

Invoice wrapping type ZF2

Version 1

Screws 1-3x20 according to GOST 1145-80 or GOST 1146-80 (4 pcs.).

An example of a symbol for a right-hand wrap:

ZF2 P GOST 5090-86

The same, execution 2:

ZF2 P-2 GOST 5090-86

Overhead gate valve type ZT

Screws 1-3x25 or 1-4x25 according to GOST 1145-80 (4 pcs.).

An example of a symbol for a gate valve with overlay:

ZT (+15) GOST 5090-86

The same, without float:

ZT () GOST 5090-86

Screed type ST

Screw VM6-6g x 55.36 according to GOST 17473-80, GOST 17474-80 or GOST 17475-80.

Screws 1-3x25 according to GOST 1145 (2 pcs.).

An example of a screed symbol:

ST GOST 5090-86

6. The bolts of mortise latches and screws in the open position should not protrude above the front surface of the slats or fall inside the body by more than 1 mm.

7. The dimensions of the bolt and locking strip of bolts of types ShN1, ShN2 and gate valves of type ZT must ensure an interference fit of at least 3 mm when connecting them.

The thickness of the locking strips of these products should not be less than 1 mm.

8. The cord of a PF2 type transom fixture must move freely along the rollers, without jamming and not slip off them.

9. Wrapping types ZR1, ZR2, ZR4 and ZF1 should be made double-sided, types ZR3 and ZF2 - in right and left versions.

10. The bolt of the 3T type valve must be made of steel rod.

11. The shape of the handles, linings, the cross-section of the bolts of overhead latch bolts, as well as the pointed part of the pins for screwing, are not established by the standard.

12. Locking products must have a protective or protective-decorative coating in accordance with GOST 538-88 for 2, 3 or 4 (C) groups of operating conditions of GOST 9.303-84.

13. Bolt-rods of overhead latches should be tested for strength during acceptance and type tests.

After testing, the latch bolt should not be deformed.

14. Transom devices of types PF1, PF2 and wrappings of types ZR1, ZR2, ZR3, ZR4 must be equipped with the following parts specified in Appendix 1:

Transom devices of types PF1, PF2, installed on transoms with separate frames, - with two connectors of design 1, 2, 3, 4 or 5 (drawings 1, 2, 3, 4, 5);

Transom devices of type PF2, installed on transoms with single or paired sashes, - two stops (Fig. 7);

Transom devices of type PF2, installed on transoms with triple glazing, - two stops and two connectors (Fig. 6 and 7);

Screws of type ZR1 - with handles of type P1 (Fig. 8);

Screws of types ZR2, ZR3, ZR4 - with handles of type P1 or P2 with overlays. The number of P2 type handles and escutcheons must be specified when ordering.

15. The value of transom devices of type PF1 and latches of types ShN1 and ShN2 must be indicated when ordering.

ANNEX 1

Mandatory

Accessories for transom devices

and mortise screws

Connectors for transoms with separate and separate-paired

bindings

Version 3