Today we will figure out how to produce hydraulic calculation heating systems. Indeed, to this day the practice of designing heating systems on a whim is spreading. This is a fundamentally wrong approach: without preliminary calculation We raise the bar for material consumption, provoke abnormal operating conditions and lose the opportunity to achieve maximum efficiency.

Goals and objectives of hydraulic calculations

From an engineering point of view, a liquid heating system seems to be a rather complex complex, including devices for generating heat, transporting it and releasing it in heated rooms. Ideal operating mode hydraulic system heating is considered to be one in which the coolant absorbs maximum heat from the source and transfers it to the room atmosphere without loss during movement. Of course, such a task seems completely unattainable, but a more thoughtful approach makes it possible to predict the behavior of the system in different conditions and get as close to benchmarks as possible. That's what it is the main objective design of heating systems, the most important part of which is considered to be hydraulic calculation.

The practical goals of hydraulic calculation are:

1. Understand at what speed and in what volume the coolant moves in each node of the system.
2. Determine what impact a change in the operating mode of each device has on the entire complex as a whole.
3. Determine what performance and performance characteristics of individual components and devices will be sufficient for the heating system to perform its functions without significantly increasing the cost and providing an unreasonably high margin of reliability.
4. Ultimately, to ensure a strictly dosed distribution of thermal energy across various heating zones and to ensure that this distribution will be maintained with high constancy.

One can say more: without at least basic calculations it is impossible to achieve acceptable operating stability and long-term use of equipment. Modeling the operation of a hydraulic system, in fact, is the basis on which all further design development is built.

Types of heating systems

Engineering calculation tasks of this kind are complicated by the high diversity of heating systems, both in terms of scale and configuration. There are several types of heating junctions, each of which has its own laws:

1. Two-pipe dead-end system a is the most common version of the device, well suited for organizing both central and individual heating circuits.

The transition from thermal engineering calculations to hydraulic ones is carried out by introducing the concept of mass flow, that is, a certain mass of coolant supplied to each section of the heating circuit. The mass flow is the ratio of the required thermal power to the product of the specific heat capacity of the coolant and the temperature difference in the supply and return pipelines. Thus, in the sketch heating system mark the key points for which the nominal mass flow is indicated. For convenience, the volumetric flow is determined in parallel, taking into account the density of the coolant used.

G = Q / (c (t 2 - t 1))

• Q - necessary thermal power, W
• c— specific heat coolant, for water accepted 4200 J/(kg °C)
• ΔT = (t 2 - t 1) - temperature difference between supply and return, °C

The logic here is simple: to deliver required amount heat to the radiator, you must first determine the volume or mass of coolant with a given heat capacity passing through the pipeline per unit of time. To do this, it is necessary to determine the speed of movement of the coolant in the circuit, which is equal to the ratio of the volumetric flow to the cross-sectional area of ​​the internal passage of the pipe. If the speed is calculated relative to the mass flow, you need to add the coolant density value to the denominator:

V = G / (ρ f)

• V - coolant movement speed, m/s
• G—coolant flow, kg/s
• ρ is the density of the coolant; for water it can be taken as 1000 kg/m3
• f is the cross-sectional area of ​​the pipe, found by the formula π-·r 2, where r is inner diameter pipes divided by two

Data on flow and speed are necessary to determine the nominal diameter of the decoupling pipes, as well as the flow and pressure of the circulation pumps. Devices forced circulation must create overpressure, allowing to overcome the hydrodynamic resistance of pipes and shut-off and control valves. The greatest difficulty is presented by the hydraulic calculation of systems with natural (gravitational) circulation, for which the required excess pressure is calculated based on the speed and degree of volumetric expansion of the heated coolant.

Head and pressure losses

Calculation of parameters using the relationships described above would be sufficient for ideal models. IN real life both the volumetric flow and the coolant velocity will always differ from those calculated in different points systems. The reason for this is hydrodynamic resistance to the movement of the coolant. This is due to a number of factors:

1. The forces of friction of the coolant against the walls of the pipes.
2. Local flow resistance formed by fittings, taps, filters, thermostatic valves and other fittings.
3. The presence of branches of connecting and branch types.
4. Turbulent turbulence at turns, contractions, expansions, etc.

The task of finding the pressure drop and velocity at different areas systems are rightfully considered the most complex; they lie in the field of calculations of hydrodynamic media. So, the friction forces of the fluid about internal surfaces pipes are described by a logarithmic function that takes into account the roughness of the material and kinematic viscosity. With the calculations of turbulent vortices, everything is even more complicated: the slightest change in the profile and shape of the channel makes each individual situation unique. To facilitate calculations, two reference coefficients are introduced:

1. Kvs- characterizing the throughput of pipes, radiators, separators and other sections close to linear.
2. K ms- defining local resistance in various fittings.

These coefficients are indicated by manufacturers of pipes, valves, taps, and filters for each individual product. Using the coefficients is quite easy: to determine the pressure loss, Kms is multiplied by the ratio of the square of the coolant velocity to the double value of the acceleration of gravity:

Δh ms = K ms (V 2 /2g) or Δp ms = K ms (ρV 2 /2)

• Δh ms — pressure loss at local resistances, m
• Δp ms—pressure loss at local resistances, Pa
• K ms - local resistance coefficient
• g—gravitational acceleration, 9.8 m/s 2
• ρ - coolant density, for water 1000 kg/m 3

The pressure loss in linear sections is the ratio of the channel capacity to a known capacity coefficient, and the result of the division must be raised to the second power:

P = (G/Kvs) 2

• P—pressure loss, bar
• G - actual coolant flow, m 3 / hour
• Kvs - throughput, m 3 / hour

Pre-balancing the system

The most important final goal of the hydraulic calculation of the heating system is to calculate such throughput values ​​at which each part of each heating circuit receives a strictly dosed amount of coolant with a certain temperature, which ensures normalized heat release to the heating system. heating devices. This task seems difficult only at first glance. In reality, balancing is accomplished by control valves that limit the flow. For each valve model, it is indicated as the Kvs coefficient for fully open state, and a graph of changes in the Kv coefficient for different degrees of opening of the adjusting rod. By changing the capacity of the valves, which are usually installed at the connection points of heating devices, it is possible to achieve the desired distribution of the coolant, and therefore the amount of heat transferred by it.

There is, however, a small nuance: when the capacity changes at one point in the system, not only the actual flow rate in the area in question changes. Due to a decrease or increase in flow, the balance in all other circuits changes to some extent. If we take, for example, two radiators with different thermal power, connected in parallel with a counter-movement of the coolant, then with an increase in the throughput of the device that is the first in the circuit, the second one will receive less coolant due to an increase in the difference in hydrodynamic resistance. On the contrary, if the flow decreases due to the control valve, all other radiators located further along the chain will automatically receive a larger volume of coolant and will need additional calibration. Each type of wiring has its own balancing principles.

Software systems for calculations

Obviously, performing manual calculations is justified only for small heating systems with a maximum of one or two circuits with 4-5 radiators in each. More complex systems heating with thermal power over 30 kW require integrated approach when calculating hydraulics, which expands the range of tools used far beyond the limits of a pencil and a sheet of paper.

Today there are enough a large number of software, provided by the largest heating equipment manufacturers such as Valtec, Danfoss or Herz. Such software systems use the same methodology that was described in our review to calculate the behavior of hydraulics. First, it is modeled in a visual editor exact copy the designed heating system, for which data on thermal power, type of coolant, length and height of pipeline differences, used fittings, radiators and underfloor heating coils are indicated. The program library contains a wide range of hydraulic devices and fittings; for each product, the manufacturer has determined the operating parameters and basic coefficients in advance. If desired, you can add third-party device samples if the required list of characteristics is known for them.

At the end of the work, the program makes it possible to determine the appropriate nominal diameter of pipes and select sufficient flow and pressure of circulation pumps. The calculation is completed by balancing the system, while during the simulation of hydraulic operation, the dependencies and impact of changes in the capacity of one node of the system on all others are taken into account. Practice shows that mastering and using even paid software products turns out to be cheaper than if the calculations were entrusted to contract specialists.

Regulatory and methodological documents are provided that regulate the design of surface drainage and treatment systems (rain, melt, water-washing) Wastewater from residential areas and enterprise sites, as well as comments on the provisions of SP 32.13330.2012 “Sewerage. External networks and structures" and "Recommendations for calculating systems for collecting, draining and purifying surface runoff from residential areas and enterprise sites and determining the conditions for its release into water bodies" (JSC "NII VODGEO"). The specified documents allow for the diversion for treatment of the most contaminated part of surface runoff in an amount of at least 70% of the annual volume of runoff for residential areas and enterprise sites close to them in terms of pollution, and the entire volume of runoff from the sites of enterprises, the territory of which may be polluted with specific substances with toxic properties or significant content organic matter. Common design practices reviewed engineering structures separate and all-alloy sewerage systems that allow short-term discharge of part of the wastewater during intense (storm) rains of rare frequency through separation chambers (storm discharges) into a water body. Situations related to refusals of the territorial departments of the State Expertise and Rosrybolovstvo to approve the implementation of activities on planned capital construction projects on the basis of Article 60 of the Water Code of the Russian Federation, which prohibits the discharge into water bodies of wastewater that has not been subjected to sanitary treatment and neutralization, are considered.

Keywords

List of cited literature

1. Danilov O. L., Kostyuchenko P. A. Practical guide on the selection and development of energy-saving projects. – M., JSC Tekhnopromstroy, 2006. pp. 407–420.
2. Recommendations for calculating systems for the collection, disposal and purification of surface runoff from residential areas, enterprise sites and determining the conditions for its release into water bodies. Addendum to SP 32.13330.2012 “Sewerage. External networks and structures" (updated edition of SNiP 2.04.03-85). – M., JSC “NII VODGEO”, 2014. 89 p.
3. Vereshchagina L. M., Menshutin Yu. A., Shvetsov V. N. O regulatory framework design of systems for disposal and treatment of surface wastewater: IX scientific and technical conference “Yakovlev Readings”. – M., MGSU, 2014. pp. 166–170.
4. Molokov M.V., Shifrin V.N. Treatment of surface runoff from the territories of cities and industrial sites. – M.: Stroyizdat, 1977. 104 p.
5. Alekseev M.I., Kurganov A.M. Organization of drainage of surface (rain and melt) runoff from urbanized areas. – M.: Publishing house ASV; St. Petersburg, St. Petersburg State University of Civil Engineering, 2000. 352 p.

V. V. Pokotilov

V. V. Pokotilov

for the calculation of heating systems

V. V. Pokotilov

FOR CALCULATION OF HEATING SYSTEMS

Candidate of Technical Sciences, Associate Professor V. V. Pokotilov

A guide to calculating heating systems

A guide to calculating heating systems

V. V. Pokotilov

Vienna: HERZ Armaturen, 2006.

© HERZ Armaturen, Vienna, 2006

Preface
2.1. Selection and placement heating devices and heating system elements
in the premises of the building
2.2. Devices for regulating the heat transfer of a heating device.
Connection methods various types heating devices for
heating system pipelines
2.3. Selecting a scheme for connecting a water heating system to heating networks
2.4. Design and some provisions for the execution of drawings
heating systems

3. Determination of the calculated heat load and coolant flow for the design section of the heating system. Determination of design power

water heating systems
4. Hydraulic calculation of a water heating system
4.1. Initial data
4.2. Basic principles hydraulic calculation heating systems
4.3. The sequence of hydraulic calculation of the heating system and
selection of control and balance valves
4.4. Features of hydraulic calculation of horizontal heating systems
at hidden gasket pipelines
5. Design and selection of equipment heating point systems
water heating
5.1. Selection circulation pump water heating systems
5.2. Selection of type and selection of expansion tank
6. Examples of hydraulic calculations two-pipe systems heating
6.1. Examples of hydraulic calculations of a vertical two-pipe system
heating with overhead distribution of main heat pipelines

6.1.1.

6.1.3. Example of hydraulic calculation of a vertical two-pipe system

heating with overhead wiring using radiator valves

6.2. Example of hydraulic calculation of a vertical two-pipe system

heating with bottom wiring using HERZ-TS-90 valves and

HERZ-RL-5 for radiators and differential pressure regulators HERZ 4007

Page 3

V.V. Pokotilov: A manual for calculating heating systems

6.3.

6.5. Example of hydraulic calculation of a horizontal two-pipe system

heating using a single-point radiator valve

7.2. Example of hydraulic calculation of a horizontal single-pipe system

heating using HERZ-2000 radiator units and regulators

7.5. Examples of valve applications HERZ-TS-90-E HERZ-TS-E during construction

heating systems and during the reconstruction of existing

8. Application examples three way valves HERZ art.No7762

With HERZ thermomotors and servo drives in system design

heating and cooling
9. Design and calculation of systems underfloor heating
9.1. Design of underfloor heating systems
9.2. Basic principles and sequence of thermal and hydraulic
calculation of underfloor heating systems
9.3. Examples of thermal and hydraulic calculations of underfloor heating systems
10. Thermal calculation of water heating systems
Literature
Applications
Appendix A: Nomogram for hydraulic calculation of water pipelines
heating from steel pipes at k W = 0.2 mm
Appendix B: Nomogram for hydraulic calculation of water pipelines
metal heating polymer pipes at k W = 0.007 mm
Appendix B: Local resistance coefficients
Appendix D: Pressure loss due to local resistance Z, Pa,
depending on the sum of local resistance coefficients ∑ζ
Appendix E: Nomograms D1, D2, D3, D4 for determining specific
heat transfer q, W/m2 of the underfloor heating system depending
from the average temperature difference ∆t avg
Appendix E: Thermal Characteristics panel radiator VONOVA

Page 4

V.V. Pokotilov: A manual for calculating heating systems

Preface

While creating modern buildings Heating systems developed for various purposes must have appropriate qualities designed to provide thermal comfort or the required thermal conditions in the premises of these buildings. A modern heating system must match the interior of the premises, be easy to use and

stand for users. A modern heating system allows automatic

redistribute heat flows between the premises of the building, using as much as possible

use any regular and irregular internal and external heat inputs brought into the heated room, must be programmable for any thermal conditions the ex-

operation of premises and buildings.

To create such modern heating systems, a significant technical variety of shut-off and control valves, a certain set of control instruments and devices, and a compact and reliable structure of the pipeline set are required. The degree of reliability of each element and device of the heating system must meet modern high requirements and be identical between all elements of the system.

This manual on the calculation of water heating systems is based on the comprehensive use of equipment from HERZ Armaturen GmbH for buildings for various purposes. This manual has been developed in accordance with current standards and contains basic reference

And technical materials in the text and in appendices. When designing, you should additionally use the company’s catalogs, construction and sanitary standards, special

ancient literature. The book is aimed at specialists with education and design practice in the field of heating buildings.

The ten sections of this manual provide guidelines and examples of hydraulic

chetical and thermal calculation vertical and horizontal water heating systems with

measures for selecting equipment for heating points.

The first section systematizes the fittings of the company HERZ Armaturen GmbH, which is divided into 4 groups. In accordance with the presented systematization, we have developed

methods of design and hydraulic calculation of heating systems, which are set out in

sections 2, 3 and 4 of this manual. In particular, the principles for selecting reinforcement of the second and third groups are presented methodically different, and the main provisions for the selection are defined

differential pressure regulators. In order to systematize the hydraulic calculation methodology

various heating systems, the manual introduces the concept of “regulated section” of the circulation

ring, as well as “the first and second directions of hydraulic calculation”

By analogy with the type of nomogram for hydraulic calculations for metal-polymer pipes, the manual contains a nomogram for hydraulic calculations of steel pipes, which are widely used for open laying of main heating pipelines and for piping equipment at heating points. In order to increase the information content and reduce the volume of the manual, the nomograms for hydraulic selection of valves (normals) are supplemented with information general view valve and technical characteristics valves, which are located on the free part of the nominal field

The fifth section provides a methodology for selecting the main type of equipment for thermal

nodes, which is used in subsequent sections and in examples of hydraulic and thermal

heating system calculations

The sixth, seventh and eighth sections give examples of calculating various two-pipe and single-pipe heating systems in conjunction with various options heat sources

– furnace or heating networks. The examples also give practical recommendations on the selection of differential pressure regulators, on the selection of three-way mixing valves, on the selection of expansion tanks, on the design of hydraulic separators, etc.

underfloor heating

The tenth section provides a method for thermal calculation of water heating systems and

measures for selecting various heating devices for vertical and horizontal two-pipe and single-pipe heating systems.

Page 5

V.V. Pokotilov: A manual for calculating heating systems

1. General technical information about HERZ Armaturen GmbH products

Manufactured by HERZ Armaturen GmbH full complex equipment for water systems

heating and cooling systems: control valves and shut-off valves, electronic regulators and regulators direct action, pipelines and connection fittings, hot water boilers and other equipment.

HERZ produces control valves for radiators and heating substations with

variety of standard sizes and actuators for them. For example, for a radiator

of valves are produced the most wide range interchangeable executive me-

mechanisms and thermostats - from thermostatic ones of various designs and purposes

direct acting heads to electronic programmable PID controllers.

The hydraulic calculation method outlined in the manual is modified depending on

the type of valves used, their structural and hydraulic characteristics. We have divided HERZ fittings into the following groups:

Shut-off valves.

A group of universal fittings that do not have hydraulic settings.

A group of fittings that has in its design devices for adjusting the hydraulic

resistance to the required value.

To the first group of fittings operated in the full open or full positions

closures include

- shut-off valves STREMAX-D, STREMAX-A, STREMAX-AD, STREMAX-G,

SHTREMAKS-AG,

HERZ gate valves,

- Radiator shut-off valves HERZ-RL-1-E, HERZ-RL-1,

- ball, plug valves and other similar fittings.

To the second group fittings that do not have hydraulic settings include:

- thermostatic valves HERZ-TS-90, HERZ-TS-90-E, HERZ-TS-E,

HERZ-VUA-T, HERZ-4WA-T35,

- connection nodes HERZ-3000,

- connection nodes HERZ-2000 for single-pipe systems,

- single-point connection nodes to the radiator HERZ-VTA-40, HERZ-VTA-40-Uni,

HERZ-VUA-40,

- three way thermostatic valves CALIS-TS

- three-way control valves HERZ art.No 4037,

- distributors for connecting radiators

- other similar fittings in the constantly updated product range of HERZ Armaturen GmbH.

The third group of fittings, which has a hydraulic setting for installation of the required

O hydraulic resistance can be attributed

- thermostatic valves HERZ-TS-90-V, HERZ-TS-98-V, HERZ-TS-FV,

- balance valves for radiators HERZ-RL-5,

- manual radiator valves HERZ-AS-T-90, HERZ-AS, HERZ-GP,

- connection nodes HERZ-2000 for two-pipe systems,

- balance valves STREMAX-GM, STREMAX-M, STREMAX-GMF,

STREMAX-MFS, STREMAX-GR, STREMAX-R,

- automatic differential pressure controller HERZ art.No 4007,

HERZ art.No 48-5210…48-5214,

- automatic flow regulator HERZ art.No 4001,

- bypass valve for maintaining differential pressure HERZ art.No 4004,

- distributors for underfloor heating

- other fittings in a constantly updated range of products

HERZ Armaturen GmbH.

A special group of valves includes valves of the HERZ-TS-90-KV series, which in their

designs belong to the second group, but are selected according to the method of calculating valves

this group.

Page 6

V.V. Pokotilov: A manual for calculating heating systems

2. Selection and design of the heating system

Heating systems, as well as the type of heating devices, type and parameters of the coolant used

are taken in accordance with building codes and design assignment

When designing heating it is necessary to provide automatic regulation and devices for metering the amount of heat consumed, as well as use energy-efficient solutions and equipment.

2.1. Selection and placement of heating devices and system elements

heating in building premises

Heating design is pre-

lies comprehensive solution the following

1) individual choice of the optimal

options for heating type and heater type

new device that provides comfortable

conditions for each room or zone

premises

2) determining the location of the heating

physical devices and their required sizes to ensure comfort conditions;

3) individual choice for each heating device of the type of regulation

And sensor locations depending

on the purpose of the room and its thermal

inertia, from the magnitude of possible

external and internal thermal disturbances

tion, depending on the type of heating device and its

thermal inertia, etc., for example,

two-position, proportional, pro-

configurable regulation, etc.

4) selection of the type of connection of the heating device to the heat pipes of the heating system

5) deciding on the layout of pipelines, choosing the type of pipes depending on the required cost, aesthetic and consumer qualities;

6) selection of system connection diagram

heating to heating networks. When designing

In this case, the appropriate heat-

high and hydraulic calculations, I allow-

to select materials and equipment

heating and substation systems

Optimal comfortable conditions reached

are screwed the right choice type of heating and type of heating device. Heating appliances should be placed, as a rule, under light openings, ensuring

access for inspection, repair and cleaning (Fig.

2.1a). As heating devices

convectors. Place heating units

us premises (if there is a room

two or more external walls) for the purpose of eliminating

dation of the cold flow descending to the floor

air. Due to the same circumstances, the length

heating device should be

at least 0.9-0.7 width of window openings

heated premises (Fig. 2.1a). Floor-

The height of the heating device must be less than the distance from the finished floor to

the bottom of the window sill (or the bottom of the window opening if it is absent) by an amount not

less than 110 mm.

For rooms whose floors are made of materials with high thermal activity

ness ( ceramic tile, natural

stone, etc.) is appropriate against the background of the

vective heating using heater-

devices to create a sanitary effect with

using underfloor heating

In premises for various purposes

height more than 5 m in the presence of vertical

new light openings should be under them

place heating appliances to protect workers from cold downdrafts

current air flows. At the same time this

the solution is created directly at the floor

increased speed of cold flooring

air flow along the floor, speed

which often exceeds 0.2...0.4 m/s

(Fig. 2.1b). As the power of the device increases, the discomfort increases.

In addition, due to the increase in air temperature in the upper zone, the

heat loss from the room melts

In such cases, to ensure thermal comfort in work area and reduction

floor heating or radiant heating

using radiation heating

devices located in the upper zone at a height of 2.5...3.5 m (Fig. 2.1b). Additional

follow carefully under light openings

place heating appliances with heat

heavy load to compensate for the heat loss of a given light opening. If available in

such premises of permanent workplaces

in workplace areas to ensure thermal comfort in them using either

systems air heating, either using local radiation devices above workplaces, or using

this under the light openings (windows) for

the calculated thermal load of the device follows

protection of workers from cold downdrafts

blowing is taken equal to the calculated thermal

air flows should be placed away from

losses of this upper light opening

heating appliances with a heat load of

with a margin of 10-20%. Otherwise on

compensation of heat losses of a given light

condensation will occur on the glazing surface

saturation.

Rice. 2.1.: Examples of placement of heating devices in rooms

a) in residential and administrative premises up to 4 m high;

b) in premises for various purposes with a height of more than 5 m;

c) in rooms with overhead light openings.

In one heating system it is allowed

use of heating appliances

personal types

Built-in heating elements It is not allowed to be placed in single-layer

external or interior walls, as well as in

partitions, with the exception of the heater

nal elements built into the internal

walls and partitions of wards, operating rooms

and other medical premises of hospitals.

It is allowed to be provided in multi-layer external walls, ceilings and

floor heating elements water

heating systems embedded in concrete.

IN staircases buildings up to 12 floors

same heating appliances are allowed

place only on the ground floor at the level

entrance doors; installation of heating

devices and the laying of heat pipes in the volume of the vestibule is not allowed.

In buildings medical institutions heating devices in staircases

Page 8

V.V. Pokotilov: A manual for calculating heating systems

Heating appliances should not be placed in vestibule compartments that have

external doors

Heating devices on the staircase

the cage should be attached to separate

branches or risers of heating systems

Heating system piping should be

design from steel (except galvanized

bathrooms), copper, brass pipes, as well as

heat-resistant metal-polymer and poly-

measuring pipes

Pipes from polymer materials pro-

placed hidden: in the floor structure,

behind screens, in fines, mines and canals. Open laying of these pipelines

allowed only within the fire sections of the building in places where their mechanical damage, external

heating outer surface pipes over 90 °C

and direct exposure to ultraviolet radiation

rays. Complete with polymer pipes

compounds should be used

body parts and products corresponding

the type of pipe used.

Pipeline slopes should be taken into account

mother is not less than 0.002. Gasket allowed

pipes without a slope at a speed of water movement in them of 0.25 m/s or more.

Shut-off valves should be provided

flush: to turn off and drain water from

individual rings, branches and risers of systems

heating, for automatic or remote

tionally controlled valves; to turn off

removal of part or all heating devices in

rooms in which heating is used

occurs periodically or partially. Shut-off

the fittings should be provided with pieces

cerami for connecting hoses

In pumped water heating systems

should, as a rule, provide for

precision air collectors, taps or automatic

tic air vents. Non-flowing

air collectors may be provided at a speed of water movement in the pipe-

wire less than 0.1 m/s. Using

antifreeze liquid is desirable

use for automatic air removal

tic air vents - separators,

installed, usually in a thermal

point "to the pump"

In heating systems with bottom routing of lines for air removal, pre-

installation of air outlets is envisaged

taps on upper heating devices

floors (in horizontal systems- for each

house heating device).

When designing centralized systems

for water heating made from polymer pipes, automatic

tic control (temperature limiter)

temperature) to protect pipelines

from exceeding coolant parameters

Built-in installation cabinets are installed on each floor, in which there should be

distributors with outlets can be placed

pipelines, shut-off valves, filters, balance valves, as well as meters

heat metering

Pipes between distributors and heating devices are laid

at external walls in special protective

corrugated pipe or in thermal insulation, in

floor structures or in special plinths

sah-korobakh

2.2. Devices for regulating the heat transfer of a heating device. Methods for connecting various types of heating devices to heating system pipelines

To regulate air temperature

in rooms near heating appliances there is

blows to install control valves

In premises with permanent occupancy

nium people are usually established

automatic thermostats, providing

maintaining a given temperature

ry in each room and supply savings

heat through the use of internal

excess heat (domestic heat emissions,

solar radiation).

At least 50% of heating applications

burs installed in one room -

research, it is necessary to establish a regulatory

fittings, with the exception of indoor devices

areas where there is a risk of freezing

coolant

In Fig. 2.2 shows various options

you temperature controllers that can

be set to thermostatic temperature

diator valve.

In Fig. 2.3 and fig. 2.4 shows options

the most common connections of various types of heating devices to two-pipe and single pipe systems from-

FEDERAL AGENCY OF THE RUSSIAN FEDERATION FOR
CONSTRUCTION AND HOUSING AND COMMUNAL SERVICES
(ROSSTROY)

Introduction Section 3. General provisions Section 4. Qualitative characteristics surface runoff from residential areas and enterprise sites 4.1. Selection of priority indicators of surface runoff pollution when designing treatment facilities 4.2. Determination of calculated concentrations of pollutants when surface runoff is diverted for treatment and released into water bodies Section 5. Quantitative characteristics surface runoff from residential areas and enterprise sites 5.1. Determination of average annual volumes of surface wastewater 5.2. Determination of the estimated volumes of surface wastewater when diverted for treatment 5.3. Determination of the estimated flow rates of rain and melt water in rainwater sewer collectors 5.4. Determination of the estimated flow rates of surface runoff when diverted for treatment and into water bodies Section 6. Conditions for the removal of surface runoff from residential areas and enterprise sites 6.1. General provisions 6.2. Determination of MPC standards for pollutants when releasing surface wastewater into water bodies Section 7. Systems and structures for the collection and disposal of surface runoff from residential areas and enterprise sites 7.1. Surface runoff collection and disposal schemes 7.2. Structures for regulating surface runoff during disposal for treatment and methods for their calculation 7.3. Surface runoff pumping 7.4. Determination of Design Capacity treatment facilities Section 8. Treatment of surface runoff from residential areas and enterprise sites 8.1. General provisions 8.2. Mechanical cleaning 8.3. Wastewater treatment by flotation 8.4. Filtration 8.5. Reagent treatment of surface runoff 8.6. Biological treatment 8.7. Ion exchange 8.8. Adsorption 8.9. Ozonation 8.10. Sludge treatment 8.11. Disinfection of surface runoff Legend: BIBLIOGRAPHY Appendix 1 Classification of areas Russian Federation depending on climatic conditions Appendix 2 Values ​​of rain intensity q20 Appendix 3 Values ​​of parameters n, mr, γ for determining design flow rates in rainwater sewer collectors Appendix 4 Average duration of rain per day with precipitation Appendix 5 Methodology for constructing a graph of the probability distribution function of daily rain layers and an example of calculating the daily rain layer with a given period of a single excess of P< 1 года Appendix 6 Methodology for calculating the daily precipitation layer with a given probability of exceedance Appendix 7 Schemes for regulating surface runoff and methods for calculating the flow of wastewater discharged for treatment and into water bodies Appendix 8 Methodology for calculating productivity pumping stations for pumping surface runoff

Introduction

3. Rules for the use of public water supply and sewerage systems in the Russian Federation.

The recommendations were developed by a team of specialists from the State Scientific Center of the Russian Federation, Federal State Unitary Enterprise "Research Institute VODGEO" under the scientific supervision of a Doctor of Technical Sciences, consisting of: Candidates of Technical Sciences, Doctor of Technical Sciences, Engineer, Candidates of Technical Sciences, Doctor of Technical Sciences.

When developing the Recommendations, data from field studies obtained by specialists from the Leningrad Scientific Research Institute of AKH named after. , VNIIVO and a number of industry research organizations at enterprises in various industries, as well as data from experience in operating treatment facilities for surface runoff from urban areas and industrial enterprises, designed and built over the past 30 years.

The basis for the recommended calculation of systems for the collection and disposal of surface wastewater is the method of limiting intensities, developed and later developed by engineer, Doctor of Technical Sciences, Candidate of Technical Sciences, Doctors of Technical Sciences and A. M. Kurganov.

The authors express special gratitude to the chief specialist of the State Unitary Enterprise “Soyuzvodokanalproekt”, candidate of technical sciences for their assistance in preparing the Recommendations, as well as to the participants of the seminar of the VODGEO Research Institute “Systems for the collection, disposal and purification of surface runoff from residential areas of cities and industrial enterprises” (April 6-7, 2005 g., Moscow), dedicated new edition Recommendations for your comments and suggestions.

1 With the release of these recommendations, “Temporary recommendations for the design of structures for treating surface runoff from the territories of industrial enterprises and calculating the conditions for its release into water bodies,” published by VNII VODGEO in 1983, become invalid.

Section 1. Legislative and regulatory documents

1. Water Code of the Russian Federation of November 16, 1995.

3. Security rules surface waters. - M., 1991.

4. SanPiN 2.1.5.980-00. Hygienic requirements to the protection of surface waters.

5. GOST 17.1.3.13-86. General requirements to the protection of surface waters from pollution.

6. Rules for the use of public water supply and sewerage systems in the Russian Federation. Approved by Decree of the Government of the Russian Federation of February 12, 1999 No. 000.

7. SNiP 2.04.03-85. Sewerage. External networks and structures.

8. SNiP 23-01-99. Construction climatology.

9. GOST 17.1.1.01-77. Protection of Nature. Hydrosphere. Use and protection of water. Basic terms and definitions.

10. GOST 17.1.3.13-86. Protection of Nature. Hydrosphere. Classification water bodies.

11. SanPiN 2.2.1/2.1.1.1200-03. Sanitary and epidemiological rules and regulations.

12. GOST 27065-86. Water quality Terms and Definitions.

13. GOST 19179-73. Hydrology of land. Terms and Definitions.

14. List of fishery standards: maximum permissible concentrations (MPC) and approximate safe levels impact (OBUV) harmful substances for water from water bodies with fishery purposes. Approved by order of Roskomrybolovstvo dated June 28, 1999 No. 96.

15. GN 2.1.5.1315-03. Maximum permissible concentrations (MPC) chemical substances in the water of water bodies for domestic, drinking and cultural water use. Hygienic standards. Approved and put into effect by Decree of the Chief State Sanitary Doctor of the Russian Federation dated April 30, 2003 No. 78.

16. GN 2.1.5.1316-03. Approximately permissible levels(TAC) of chemical substances in the water of water bodies for domestic, drinking and cultural water use. Hygienic standards. Approved and put into effect by Decree of the Chief State Sanitary Doctor of the Russian Federation dated January 1, 2001 No. 78.

Section 2. Terms and definitions

For the purposes of this document, the following terms and definitions apply:

STORING CAPACITY(surface runoff storage tank) - a structure for receiving, collecting and averaging the flow and composition of surface wastewater from residential areas and enterprise sites for the purpose of their subsequent treatment.