Not many people know that blinds were invented several centuries ago. Today it is one of the most popular decorative and protective devices for windows. This article will talk about how to hang blinds on your own. plastic windows. You can find out what types of multi-leaf window curtains there are and how to properly install vertical and horizontal blinds.

Kinds

Blinds- one of the types of window curtains, devices in the form of rigid, parallel to each other and adjustable plates made of various materials- fabric, wood, metal, plastic. They have several functions:

• protect from light;
• decorate the window;
• regulate air flows.

There are several types of blinds. The most common of them are:

• horizontal;
• vertical;
• roll;
• pleated.

We suggest you understand the advantages and disadvantages of each type.

Did you know? The official history of the invention of blinds begins in 1841. It was this year that their production was patented by the American John Hampton, although the production of rigid curtains had been carried out before. So, since the 1760s, they were produced in Philadelphia by the Englishman John Webster.

Horizontal

Horizontal or Venetian blinds are thin plates (slats) that are arranged one above the other like a ladder. They are connected to each other by a cord, which allows you to open and close them, as well as adjust the height. The plates are controlled using a rotating rod. The slats can be made from different materials- wood, metal, bamboo, fabric.

The main advantages of these types of curtains are:

• good protection from sunlight;
• increased heat transfer;
• possibility of adjusting lighting intensity;
• reliability;
• durability;
• ease of maintenance and operation;
• the ability to visually expand the size of the room;
• easy installation;
• can be used for any room, including kitchen, bath, balcony;
• low cost.

There are probably no disadvantages to horizontal blinds. They can only be present depending on the material from which they are made. We will talk about them in more detail in a separate section below.

Vertical

Vertical blinds appeared somewhat later than horizontal ones - in 1960. However, they quickly gained popularity and today are successfully used to decorate various rooms.

These are plastic, metal or fabric slats suspended on a cornice in a vertical position parallel to each other and connected at the bottom with a cord. They are regulated by a side mechanism that rotates the plates - using a decorative cord (chain) they turn, and using a rope they move to one side, fully or partially opening the window.

Benefits vertical blinds are:

• versatility - the possibility of installation in window openings, to the ceiling, to the wall above the window, installation in attic and ordinary windows;
• ease of installation;
• ease of care;
• effective regulation of sunlight flows;
• good air access when darkening;
• the ability to combine with regular curtains;
• the ability to visually increase the height of the room.

Disadvantages include:

• inconvenience when moving to the side when opening the window;
• impossibility of placing flowers on the windowsill when mounted in a window opening.

Rolled

Roller blinds have recently come into the spotlight modern design apartments They are preferred by those who love coziness and comfort in their home. They are the ones who can create them in the bedroom, living room and kitchen. Besides appearance Roller blinds are more attractive than other types, while functionality also remains high.

They are designed in the form of a horizontal shaft on which a roll of fabric is wound, and a control mechanism in the form of a cord, a spring holder or an electric drive. The fabric can be lowered and raised to the desired length, completely or partially covering the window. Roller blinds are mounted in the window opening, on the ceiling or on the wall, on the window sash.

The advantages of roller blinds are:

• ease of operation;
• easy to care for - the fabric is impregnated with a dust- and water-repellent composition;
• the ability to implement any design idea;
• durability;
• good protection from sunlight and room overheating;
• the ability to create any degree of room illumination;
• environmental friendliness;
• ergonomics;
• Possibility of installation on roof windows;
• when installed on each sash, there is no interference with opening windows and decorating the window sill;
• possibility of making curtains from transparent materials.

The disadvantages include the price, which is much higher than that of the more familiar and common horizontal and vertical structures, as well as the fragility of the spring holder.

One type of roller blinds is cassette. This is an option designed for plastic windows. It is assumed that the slats or fabric roll, when closing, are hidden in a specially designed box (cassette) attached to the window sash.

This design allows you to save space, free up the window and window sill, and additionally protect the material from dust, dirt, and deformation. Cassette options are made of fabric, bamboo, aluminum, and plastic. There are three types of cassettes: round, angular and flat.

Pleated

Another option for fabric blinds is pleated. As the name already suggests, these are fabric curtains gathered into a small fold. Their choice is huge and comes in various colors, fabric density, and shapes. Some of them are sewn using a special pattern.

Thanks to this, pleated curtains can fit into any interior, creating an original atmosphere. This option is a piece of fabric that is attached to a special profile and controlled using a chain, cord or electric drive.

Advantages of pleated curtains:

• originality;
• external attractiveness;
• good functionality;
• durability;
• reliability;
• miniature design;
• the ability to design a window of any shape and from any material.

Original and sophisticated solutions The interior cannot do without the use of multi-textured blinds, i.e. those in which the slats are made of various materials using a variety of decor.

Types of material

As already mentioned, in different time blinds were made from various textures. Today, the most common materials for rigid window curtains are fabric, plastic and aluminum, and less often wood. Each of them has both pros and cons.

Fabric

Textile blinds- this is one of the best options for decorating windows and protecting the room from sunlight in apartments and houses. There are both horizontal and vertical designs.

Many people are attracted by the appearance and huge selection of colors of fabric blinds, but are put off by the idea that they will require the same care as regular curtains. However, it is not.

Textiles for blinds are impregnated with special impregnations that prevent dirt, dust and moisture from being absorbed. Maintenance will consist only of periodically wiping the material with a slightly damp cloth and vacuuming.
High-quality textile blinds do not fade, do not deform, fit into any interior, and are not too expensive. However, compared to metal, plastic and wooden structures have a shorter service life. Textile models are not the best option for the kitchen or catering establishments, as they can absorb odors.

Did you know? The first blinds were made from wooden slats. They were replaced by metal curtains. After World War II, fabrics were also used to make window security devices.

Plastic

One of the most purchased types, due to its low price and the possibility of use in various rooms- office, apartment, public, utility, high humidity. The polymers from which the lamellas are made can be of varying degrees of light transmission, of various colors, with or without patterns. They are practical, lightweight, easy to install and maintain, and are sold at the best price.
Among the disadvantages:

• creating noise in a draft, with open windows;
• some polymers turn yellow under prolonged exposure to sunlight;
• cannot be used near stoves or other heating devices due to poor fire resistance;
• release of toxic substances during a fire.

Aluminum

Along with plastic ones, aluminum blinds are also popular. They have high strength, durability, fire resistance, and the ability to withstand different temperatures and moisture. Most often used to protect windows in in public places, offices, medical institutions. They have an attractive price. They can be horizontal, vertical, cassette.

Disadvantages include heavier weight and the creation of a noise effect in drafts.

Wooden

Wooden blinds are used in certain types interior, they go well with fabric curtains and natural wood furniture. They allow you to create a warm homely atmosphere. They are reliable, strong, durable, environmentally friendly, and protect well from the sun. At the same time, they are one of the most expensive options.

Installation technology

You can install blinds without the help of professionals. We offer you instructions for working with horizontal and vertical rigid curtains.

Horizontal

Horizontal structures can be fastened in four ways:

• to the ceiling;
• to the wall above the window;
• in a window opening;
• to the window sashes.

First you need to take measurements. The height and width of the window opening are measured with a tape measure. On a piece of paper you need to draw a diagram of the window, on which you can then take measurements.

When installing curtains in a window opening their size is calculated by subtracting 1 cm from the height and 2 cm from the width.

When installed above a window opening The size of the blinds is calculated based on adding 5-7 cm to its height and 20 cm to its width.

When attached to the sash The width is measured from the joint of the bead with the window on the left side to the joint of the bead with the window on the right side, adding 1 cm.

When measuring height on a blind window 3 cm is added to the distance from bead to bead, on the sash - 4 cm.

Video: how to correctly measure horizontal blinds

Conventional horizontal blinds consist of the following elements:

• upper part - rotary axis, rollers, cornice, brackets, cord clamp, swivel mechanism, top cover;
• middle part - lamellas and plug;
• lower part - lower cornice, side covers.

For installation you will need the following tools:

• screwdriver;
• pencil;
• screws.

The technology for installing ready-made aluminum blinds on plastic windows is as follows:

1. Straighten the structure.
2. Remove the control handle.
3. Attach fasteners to the top bar.
4. Attach the structure to the installation site and mark the mounting locations for the brackets. The distance between them should be at least 60 cm.
5. Attach the brackets to the wall, window frame or sash.
6. Insert the top cornice into the brackets.
7. Open the blinds and mark the attachment points for the lower fasteners.
8. Attach the lower clamps.
9. Insert the adjusting knob.

Important!Make sure that the brackets do not get caught in the control mechanism, cord clamp or support.

Video: installing horizontal blinds

If the finished blinds are longer than necessary, they can be trimmed. To do this, you need to remove the side ones and remove the lower clamps from the bottom bar. Then pull out the knots of the cord from the two holes formed and untie them. Remove excess slats. Re-insert the cords into the holes in the bottom bar and tie knots. Replace the bottom and side clips.

It is possible to shorten the blinds in width, but this is much more difficult to do. In order not to spoil the curtain, it is better to contact a specialist. For pruning you will need a fine-toothed hacksaw. The slats should be folded into one strip and cut to the required length. Then polish the ends with a file and, if necessary, tint.

Installing roller blinds

to install roller blinds on a wall, in an opening or on a ceiling, drilling and the presence of a drill or hammer drill will be required, depending on the material from which the ceiling and walls are made. For plastic or wooden windows roller blinds secured with double sided tape and PVC staples without drilling.

If the blinds will be attached to the sash, then to calculate their dimensions you will need to know not only the width and height of the window, but also the depth of the glazing bead. The choice of system will depend on the latter size. If the bead depth is more than 1.5 cm, you need to pay attention to the Uni type system, up to 1.5 cm - Profil and Mini.
Add 3 cm to the width of the glass - this will be the width of the curtain. The length of standard curtains is about 2 m. If they are too long for your windows, they can be trimmed.

Important! The length of roller blinds is calculated based on the fact that there must be at least 50 cm of fabric on the roll.

The technology for fastening roller blinds without drilling is as follows:

1. Install a plug on one end of the roll, and a rotating mechanism with a plastic chain on the other.
2. Insert the clamp into the bracket and fasten it to the bracket.
3. Install the brackets into the roll according to the instructions.
4. Attach the curtain to the mounting location.
5. Mark the mounting locations for the brackets.
6. Check that nothing is blocking the opening of the curtain.
7. Degrease the place where the brackets are attached.
8. Place tape on the sash where the bracket is attached.
9. Degrease the brackets.
10. Unstick protective film tape.
11. Hang the blinds by pressing the tape where they are attached.

Video: how to install roller blinds

If you purchased ready-made curtain, but it does not fit your window, then its size can be reduced. In order to shorten them in width, you will need to cut the roll, the canvas and the bottom rail. It is much easier to cut the fabric to length. The fabric is cut with ordinary scissors under a ruler, and then the bottom rail is attached to it.

Installation of cassette blinds

Cassette blinds are also attached using tape. In order to install them, you must:

1. Print the product.
2. Degrease the place of attachment to the window frame.
3. Attach the cassette to the attachment point and lower the fabric to the bottom position.
4. Mark the location where the cassette is attached with a pencil.
5. Remove the protective film from the tape attached to the back of the cassette.
6. Place the cassette on the frame, press and hold for a few seconds.
7. Carefully remove protective layer tape from the top edge of the metal fabric guides on both sides.
8. Install the guides into the groove of the curtain body cassette and press down.
9. Gradually removing the protective layer of tape, press the guides parallel to the frame bead.
10. Do the same on the other side.
11. Install a limiter.

Video: installing cassette blinds

Vertical

Vertical curtains can be attached in three ways:

• in a window opening;
• to the wall above the window;
• to the ceiling.

They can have left-hand, right-hand and central control. Below you will find instructions on how to install vertical rigid curtains yourself.

In the window opening

To calculate the dimensions, you need to measure the width of the window opening and subtract 1-1.5 cm. Measure the height of the opening and subtract 1.5-2 cm. Measurements must be taken 5-7 cm deep into the opening, since it usually narrows. To make sure that after installing the blinds the sash will open, you need to measure the distance from the top edge of the sash to the upper slope of the installation point of the cornice. The distance must be at least 4.5 cm. Otherwise, you will have to measure into the overlay. Since the window may be uneven, measurements of width and height must be made at three points.

You can attach vertical blinds to a window opening in this way:

1. Mark the attachment points.
2. Drill holes.
3. Install brackets.
4. Insert the curtain rod into the special grooves on the holders and snap the locks into place.
5. Install fabric.
6. Insert weights.
7. Secure the bottom chain.

Above the windows

To calculate the size, add at least 18-20 cm on each side to the width of the window opening. You will also need to measure the distance from the ceiling to the upper corner of the slope. From top corner the slope should be retreated at least 10 cm. Measurements with fastening to the ceiling are made by subtracting 1-2 cm from the distance “ceiling - window sill”, “ceiling - floor” - 4-7 cm.

With the advent of relatively inexpensive blind systems on the market, the fight against scorching sun rays has become completely new level. Instead of reflective and tinting films, coated glass and all other nonsense, it became possible to mount blinds on plastic windows once and use the simple, but very convenient device. There is not much work involved in installing protective slats, and the process itself is not particularly difficult; you just need to carefully read the instructions for attaching blinds to plastic windows and determine for yourself the most comfortable option placement of fasteners on the window frame.

How blinds work

According to the designers, no matter which systems are selected for packaging metal-plastic windows, they look much more elegant framed by blinds than in combination with traditional curtains and curtains. The exception is fabric screens and roller shutters, which are quite suitable in design and appearance for any type of curtains. On the other hand, vertical blinds, which cover not just the glass, but the entire window opening, can hardly be considered comfortable for the home. Unless, of course, the interior of the apartment is made in an office style.

The design of blinds consists of four main elements:

• Long horizontal strips or lamellas that can rotate around their axis and thereby change the degree of darkening of the window opening;
• Suspension systems, as a rule, are several vertical nylon or propylene lines threaded through holes on the edges of the slats;
• Curtain strips with fasteners that hold the blinds in a fixed position on the plastic window;
• The control system is most often made in the form of two cords or a plastic rod attached to a small metal fork of the curtain rod.

In order to close the blinds on a plastic window, in the first case you just need to carefully pull one of the cords. Controlling the blind slats using a rod is even simpler - you just need to turn the rod a few times to close or open the slats. Of course, for normal operation it is necessary to firmly fix the brackets or cornice strip, and only then check the performance of the lamellas.

For your information! Everyone has inexpensive models blinds, despite the wide variety of shapes and designs, have the same drawback. The lamella control mechanism and fastening are manufactured with a minimum margin of safety.

Therefore, before attaching blinds to plastic windows, it is necessary to check their performance in a suspended state. The main thing is not to exert much physical effort during the first attempts to fix the structure on a plastic window and not to try to bend the fastening if something suddenly goes wrong.

In addition, often a plastic window is ordered and installed with one opening sash adjacent to the side slope. Therefore, before fastening the blinds, you need to install a limiter so that when opening the shutter wide open, the plastic window frame does not damage the fastening and slats. In this case, you can use the hint on how to attach blinds to plastic windows shown in the video:

Materials for making blinds

In most cases, the blind manufacturer suggests fixing the curtain rod to plastic profile windows or a glazing bead that seals a double-glazed window, so almost all lamella systems have a fairly low weight. The exception is models with long slats or with built-in automatic system opening-closing, such structures are best fixed on ceiling slopes or walls.

Most often, lightweight materials are used to make lamellas; the lighter the structure, the easier it is to secure it in the most inconvenient places:

• Aluminum sheet profile;
• Plastic stamped profile;
• Wooden planks made from bamboo or valuable species wood;
• Planks made of pressed wood fibers with a laminated coating.

The most expensive and capricious material is wood, despite the very beautiful design and high price, such blinds, before being fixed, often have to be adjusted to the installation location many times in order to ensure uniform tension of the canvas. The most unpretentious and crush-resistant plastic slats.

These blinds do not scratch plastic frames, they are easy to wash and clean. In some cases, if desired, the blinds can be fixed between the outer mosquito net and a plastic window. Aluminum blinds are considered the most resistant to sun exposure, so they can be mounted on the glazing of balconies, loggias, large window openings.

Installation options for horizontal blinds

There are many ways to secure the curtain rod and blinds to a plastic window, but before choosing an installation option, use good advice- do not buy ready-made blinds systems in a store, market or salon.

Advice! If you have the opportunity, order production protective cloth and fastenings in a specialized company.

• Firstly, such blinds are of better quality than ready-made ones, and even if a defect is discovered, you can always solve the problem by repairing or returning the product.
• Secondly, specialists from such companies often develop their own versions of curtain rods, which are much easier to attach to plastic windows than Chinese consumer goods.
• Thirdly, such salons hold free installation promotions, so that when ordering blinds for several plastic windows, you can install them completely free of charge and with a guarantee.

You can attach blinds to a window in the following ways:

• By inserting supporting brackets into a plastic or wooden frame using self-tapping screws;
• Glue the cornice strip to the plastic using PVC glue or secure it with double-sided tape;
• Hang the blind track on the opening sash using aluminum hooks.

In the latter case, the hooks are simply placed on the upper edge of the window, without any additional fasteners.

Before ordering, you only need to measure the size of the future canvas using the bead of the plastic window, since each apartment has its own window opening size, and, accordingly, the height and width of the glass will also differ.

Self-tapping installation

Before attaching the support bar to the plastic window, you just need to attach the assembled blinds to the top crossbar of the frame to make sure that the delivered copy fits your plastic window.

At the second stage, carefully remove the metal brackets from the curtain rod of the blinds in order to secure them with self-tapping screws on the plastic profile. It is necessary to choose the position of the fastener so that the lower edge of the bracket is in line with the bead. If the window was installed by professionals, then the conditional line between the holes for the screws will exactly correspond to the horizon. Otherwise, before fixing the brackets with self-tapping screws, it is better to once again make sure that the choice is correct using a building level.

Some craftsmen believe that it is best to secure the blinds with glazing beads; they are easier to change than to repair the plastic window profile. But the glazing beads are not always fastened rigidly enough, so over time such fasteners may simply fall apart.

In order to secure the bracket to the plastic, one self-tapping screw is enough. We pre-drill holes with a 1.5-2 mm drill and tighten the fasteners with a screwdriver. Drilling is a must; often old, dried-out plastic or wood would develop transverse cracks when trying to screw in a self-tapping screw without drilling.

In a similar way, you need to secure the lower plastic brackets; they are used to tension the blinds. On the upper eaves strip you need to install plastic “cheeks”, with which the entire structure will simply snap onto the previously installed mount.

On the bottom bar, secure the axles in the holes of the plastic fasteners. All that remains is to put on the side plugs and connect the lamella control rod.

To drill or not to drill a window frame

Owners of brand new plastic windows do not always have the fortitude to drill holes in order to secure the bracket. Old profiles and wooden frames They drill without hesitation, and new windows are such a shame. Anyone who has ever tried to attach blinds with their own hands notes that aluminum fasteners always leave marks on the delicate plastic surface of the window.

In this case, you can attach the blinds to a plastic window without drilling, using double-sided tape, PVC glue or cyacrine. The easiest way to attach the glue to the plastic surface of the window frame is with tape. The adhesive surface, treated with a modified rubber adhesive mass, can withstand loads of up to 50g/cm2. The weight of the structure is just over 300 g, so a narrow strip of 50x2cm is enough to secure a load weighing almost 5 kg.

There are plenty of double-sided adhesive tapes on the market, and there are also those on which it is impossible to attach not only blinds, but even an ordinary calendar, so before installation you need to check the strength of the adhesive tape on any plastic surface. Sometimes the kit comes with brackets printed with reverse side adhesive layer. If the purchased blinds belong to a well-known manufacturer, then you can try to secure the bar using standard fasteners. But most craftsmen prefer adhesive tape, as it gives an order of magnitude higher strength, video:

Initially, you will need to mark the mounting height of the top bar and clarify the horizontal position according to construction level. All that remains is to carefully stick a strip of tape on the back side, carefully smooth it, remove the protective film and secure the blinds to the plastic surface of the window. If you need to glue an aluminum cornice strip, then before sticking the tape you need to carefully degrease the metal using a solvent or acetone.

If you need to secure the blinds to the opening sash, it is best to use a set of special overhead hooks or clamps. It is enough to install a couple of such clamps on the upper edge of the window, and you can immediately fix the bar with the blinds. Sometimes clamps are made with an additional adhesive base to avoid waste plastic bracket from the window profile.

Conclusion

Any fastening option is designed for a long service life, but if for objective reasons you have to remove the blinds, the holes from under the screws can be sealed acrylic glue or close with a decorative plastic plug. When removing double-sided tape, a regular razor blade or sharp knife works very well. You just need to pry up the edge of the tape and carefully remove the tape; traces of the adhesive base can be easily removed with alcohol or simply wiped off with a clean damp cloth.

Large windows in an apartment or house are, of course, good. A lot comes into the room daylight, especially if the windows are new from profile or wood, allowing you to maximize the glass area. However, there is often too much sunlight, especially if the windows face south or east. escape from scorching sun There are several ways, and the simplest and most optimal of them may be to install blinds on the windows with your own hands. Other options include replacing double-glazed windows with the installation of tinted glass or using tinting film. Only this option is much more expensive and not as effective if you want to completely block access to sunlight into the room.

Types of blinds and mounting features

On this moment window manufacturing companies provide wide choose blinds various configurations and the possibility of making them to specific window sizes. Among possible variations There are several main types of blinds:

• vertical;
• horizontal;
• roller shutters (fabric, internal roller shutters).

The option of installing vertical blinds in a residential apartment or your own house is quite questionable. Still, they are too strongly associated with office space. However, they are also suitable for some design solutions interior execution. They are mounted above the window, actually instead of curtains, which further limits their usefulness.

A more extensive number of mounting options is provided by the use of horizontal blinds. They can be installed on top of the window opening and along the outer edge on the upper slope of the window and directly on window design, in this case, separate blinds are installed on each sash. The last two options will go perfectly with any curtains and curtains, and choosing the last type of installation on the window itself will not take up any space on the windowsill. Roller shutters are also mounted directly on each glass.

Choose suitable option Everyone should do it independently, based on their preferences and requirements.

Common methods of attaching blinds

Having decided on the type of blinds to be installed, you can go order them from a good window manufacturer. It’s better, of course, to contact the same company that made your windows. To order you will need to give detailed dimensions windows or the dimensions you require when it comes to blinds installed over the window opening. Blinds are made quite quickly, the technology is as well developed as the production of the windows themselves, especially since the design is quite simple.

Along with the blinds themselves, as a rule, instructions are also included, which tell in sufficient detail how to install the blinds. The whole process is quite simple, and everything can be done with your own hands. If you have some skills in working with a screwdriver, you have the necessary drills, screwdrivers and a ruler with a pencil, then you can begin the installation process and do not need the help of a master installer.

It is worth considering in detail the option of installing horizontal blinds directly on the frame of each section of the window and sash. This process the most complex and visual. Note that the installation of roller shutters occurs in a similar way.

So, the packaging from the manufacturer contains everything you need to install blinds. The main part is wound with fishing line and a control chain. All additional parts and screws are packed in bags. Everything is carefully unwound, and all trim is removed from the curtain rod. There are several ways to attach blinds to a window sash:

1. fasten with screws;
2. use brackets for fastening;
3. the old fashioned way, by drilling holes in the wall;

In the version with screws, holes will inevitably be made in the window profile. This is a reliable and durable method of fastening, especially since the tightness of the entire window and the profile in particular will not be affected. However, for some this may not be suitable, if only because the blinds may have to be removed, and then the holes will already be a significant drawback. In order to avoid these consequences, you can use the option of securing the blinds to brackets that are attached to the frame different ways not requiring the creation of holes.

Installation of blinds with drilling plastic or using a screwdriver

In the first option, using screws, it is necessary to place and mark the position of the top bar of the blinds, which will be directly attached to the window, as accurately as possible. The most common and simple option is a structure that is located along the upper edge of the double-glazed window and only with its wing-grooves enters window frame. Strict attachment to the top of the sash allows you to install the blinds yourself, even without special precision and measurements.

If you have a plastic window, then you don’t have to think about drilling at all. Most manufacturers have blind models that require screws screwed directly into the profile to securely fasten them.

example of horizontal blinds

Attach the carrier to the glass unit at the very top of the sash frame. Due to the different depth between the plane of the glass unit and the frame, the fastening plates may not fit tightly to the window profile. To eliminate this gap and securely attach the plates to the window, special U-shaped pads are used. They are placed from one to several pieces until the gap is completely closed. Mark the position of the carrier along the lower edges of the fastening plates, so that later you can use them as a guide and hang the blinds evenly on the window.

You can attach blinds to plastic windows with screws directly into the profile using a screwdriver. They will easily fit into the plastic and will hold securely. You can first mark the position of the screws and make holes in these places with a drill of approximately 1.5 mm. This, firstly, will eliminate the possibility that when tightening the screw the load-bearing part will move slightly and, secondly, will eliminate the risk of cracks forming in the profile. The latter case is practically unrealistic for new windows, but it is possible if the windows have been standing for several years or are made not of plastic, but of wood.

As soon as the last screw of the fastenings is tightened, you can begin to fasten the fishing line, which will hold the blinds in the plane of the sash when opened. To do this, two holes are made in the lower bead of the sash along the edges. They must be located strictly under the corresponding line exits on the supporting system of the blinds. A 2.5 mm drill is used. The fishing line, threaded into the blind system and lowered at the ends to the bottom glazing bead, is threaded into the special plugs that are included and tied in knots. All that remains is to thread the plugs into the holes and pull the entire line from above. The line tension should not be strong, but it should not sag either.

All that remains is to put the trim on the carrier of the blinds, check their operation and glue them in suitable fastening places for the control chain and flexible lever.

Video: attaching blinds with screws

Installation of blinds without any drilling

Using brackets can help you figure out how to attach blinds to windows without drilling. They are attached to the frame in various ways, and the support of the blinds themselves is snapped or screwed onto them. This system The good thing is that later the blinds can be easily detached for major cleaning, or you can completely remove the blinds from the window and use it without them, if necessary. In this case, there will be no extra holes left in sight, and the tightness of the window profile will not be compromised.

The brackets can be secured, as in the first case, with screws or in one of the following ways:

1. hook on top part sash profile (installed only on opening sashes);
2. using double-sided tape.

Using the first option allows you to remove even all the brackets from the window in one fell swoop and does not require any additional actions at all with screwdrivers and holes. The second installation option is similar in installation to the described option when using screws, only gluing is done rather than screwing.

Instead of holes for the holding line, special fasteners can be used, which are also glued to the bottom of the frame with double-sided tape.

Humanity has been trying to cover windows from prying eyes and sunlight since ancient times. Previously, curtains were used for this, but now blinds are becoming increasingly popular. The slats in them can be either horizontal or vertical.

Horizontal blinds are divided into different types: attic, roller, bamboo shutters, etc. Such devices have different mechanisms functioning, dimensions.

They are attached to the frames; they can be installed on top of the window block or inside the frames. It all depends on the wishes of the apartment owner and the dimensions of the window opening. Most often, such structures are installed in offices, houses, apartments, factories, retail outlets, shops. Their color palette very rich.

The product can be attached to the profile of plastic windows in two ways:

1. Using self-tapping screws. This method involves drilling. Disadvantage: after dismantling it is difficult to remove the remaining holes from the fasteners.
2. No drilling. In this case, the entire structure is less stable, but the appearance of the window does not deteriorate.

In order to install blinds on a plastic window we will need:

• Screwdriver (screwdriver).
• Slats (for each sash).
• Pencil.
• A little time and patience.
• Bottom fasteners (2 pieces per sash).
• Upper fasteners (2 pieces per sash).
• Self-tapping screws (4 per sash).

Work progress

• Unpacking, we unwind the cord for adjustment.
• We remove the adjusting bar.
• We need to put a bracket on the top of the product.
• We make a measurement. To apply markings, it is recommended to apply a spirit level so that the top plate is strictly horizontal and does not fall to the side or down. If the window itself is installed with a skew, then the installation is done based on this skew of the sashes.
• We put a mark where the self-tapping screw will be screwed in.
• We check the correctness of the marks.
• Let's try it on again and remove the brackets.
• We take the right bracket, apply it to the intended area and screw it in with a screwdriver.
• We install the second bracket in the same way.
• We put on the blinds and open them.
• We place clamps on the sides of the canvas.
• Let's check if the mechanism works.

To clean, snap off the bottom slats and pull the blinds upward. We wipe the window and put the slats in place. The dust is swept away with a broom; after cleaning, an antistatic aerosol should be treated so that the structure collects less dust.

Fastening without screws

Typically, such fasteners are used in rented areas, when the appearance of the windows cannot be spoiled.

We will need:

• Scissors.
• Double-sided tape.
• Set of blinds.
• Pencil.

Work progress

• Unpack the package.
• We remove the adjustment bar so that it does not interfere.
• Place the block with the wrong side up.
• We measure the length of the tape equal to the length housings.
• Cut off the excess tape.
• We remove protective strip and glue it to the wrong side of the block.
• We try on the location of the blinds relative to the window sashes.
• We mark the points where the ends of the blinds will be attached.
• Remove the protective strip and glue the top part.
• We press the profile well to the surface.
• We install the adjustment bar.
• We check the operation of the structure.

Important! The width of the tape should be approximately equal to the width of the block. We smooth out the tape so that there are no blisters; it should lie evenly over the entire surface.

We attach horizontal blinds to wooden windows

We take measurements

We measure the dimensions, taking into account the size of the window. When installing in an opening, subtract 1 to 2 centimeters. This is a correction for uneven slopes. After this, we determine where the controls will be located (left or right side). After this, you need to decide on the type of brackets that will be used (standard; twist model). We measure the length of the handle to control the structure; usually its standard size occupies 2/3 of the entire height of the product.

Important! The maximum width of the lamellas is about 22 centimeters. There are also larger sizes in stores, but with a width of, for example, 30 cm, no one can guarantee that the blinds will open and close well. The recommended maximum height of the structure should be no more than 2.5 meters.

How to attach horizontal blinds to look like wood

This is a design with aluminum slats that imitates natural wood due to polymer coloring. It's perfect to complement classic interior. In appearance they look like wood, but are less capricious and easy to use.

• We make outlines with a pencil in the places where the brackets will be installed. There should be at least 60 centimeters between them.
• Please note that the brackets should not interfere with the assembly of the blinds or get into the latch or other moving parts of the mechanism.
• We attach them to the sash, wall or ceiling (depending on the owner’s preferences).
• Turn the latches counterclockwise until they click.
• We place the upper part in the fasteners and screw the latches until they stop, turning them clockwise.
• We check the operation of the entire structure.

How to attach horizontal beech blinds

What you will need for installation:

• Phillips screwdriver.
• Level.
• Felt pen.
• Pliers.
• Roulette.
• Hammer.

We take measurements and markings

It is necessary to pay attention that after installation the product should not block the access to the window handle and should not interfere with closing and opening it. We outline places for installing brackets. One of the upper mounts should be located next to the mechanism. Because when folding and unfolding, a large load is placed on this place and it is easy to break the fastening.

Mark the required points with a marker. Self-tapping screws should not be taken more than 1 cm, otherwise there is a high probability of damage to the glass unit, which will lead to its depressurization. Because of this, constant condensation will begin, which will disable the window opening mechanism.

Mounting on inclined windows

• We install twist brackets on the top of the window.
• Plastic brackets are installed on the bottom.
• We fasten the cables to the bushings.
• We put bushings in the holes in the upper cornice.
• We install on brackets.
• We pass the cable through the holes at the edges of the planks.
• We put the second set of bushings in the holes in the lower brackets. We pass the cable through it and fix it with a screw at the top.
• We fix the window handle.
• We check the operation of the entire mechanism.

Differences between horizontal and roller blinds installation

Rolled - this is a single canvas wound into a roller. Such a canvas is usually fixed above the window, and the lower edge of the product is equipped with a special rail to make the structure heavier. This product open type. They are recommended to be installed above the window.

Design closed type It is a box with a roller closure and side dies that help fix the canvas to the window. They are often equipped with electric drives, which operate from a control panel. This system makes such structures more comfortable to use.

While horizontal blinds are attached to the wall, to the ceiling, they can be installed between frames (mainly used for wooden windows).

Conclusion

Horizontal blinds – universal method improve the window opening. Due to the variety of materials and colors, they are used for installation in apartments, private houses, offices, and retail outlets. Installation methods are easy to select depending on the owner’s wishes: outside, inside the opening, on the window frame, between the frames.

The most important advantage is that almost anyone can install such a mechanism with a minimum set of tools on hand (screwdriver, screwdriver, knife, hammer), a little patience and dexterity. Blinds do not block light sources completely, but help create diffused lighting.

Ten years ago, blinds were considered exclusively an office window decoration item. But recently the lamellas have changed, new design options have appeared. Designers began to use bamboo, linden logs, cherry wood and fabrics as production materials. It has become fashionable to select models for furnishing houses, apartments and public premises. When you turn to a salon or specialized store for help, you will receive competent advice from a sales consultant on installation, care and selection. If you are going to install blinds on your windows yourself, read our article in detail.

You need to know this in advance before installation!

To ensure that the blinds last a long time, try to install them carefully. If you understand the details in advance, the installation process will not take much time. The main thing is to take into account the models, installation method and take this into account during assembly. If you attach window blinds you will be directly against the wall, you need to make sure that its surface is perfectly flat.

Important point! When purchasing, be sure to check with your consultant whether all parts of the mounting set are included in the kit. There are situations when a purchase additional fastenings inevitable. It's better to take care of this in advance.

Blinds can be attached in one of four ways:

• to the ceiling;
• to Wall;
• inside the window opening;
• for each window division.

It doesn't matter which option you choose. It all depends on the individual preferences of the client. Installed on double glazed windows various forms. But the method of fastening is selected individually. The sequence of steps is approximately the same, but there are some distinctive details.

Universal step-by-step steps for installing blinds

1. Many are sure that models sell standard size and neglect preliminary window measurements . We would like to warn you: take the time to measure the height and width of the window opening.
2. Be sure to note that the length of the slats should be two centimeters shorter than the length of the window. If you envisage the option of attaching the structure to the wall, then the canvas should cover the window fifteen centimeters on the right and left.
3. Next, mark the fasteners. Make sure that there are no difficulties with the operation of the mechanisms and that they will easily allow you to open the window.
4. Using the markings, attach the necessary parts to the base. Dowels and screws are screwed into the wall or ceiling. Sometimes directly into the glass unit. Next, a cornice is hung on them, which holds the structure.
5. As soon as you finish installing the blinds, check their mechanism.

Installation of blinds on plastic windows

Installation of blinds on plastic windows is a common occurrence. Most modern double-glazed windows are made of plastic. This is a fragile material, so you need to work with it carefully. Now we will look at installation options where drilling is used:

We install vertical blinds on plastic windows

This is one of the common types. Functional features, a wide color palette, ease of care and color combinations attract buyers. That's why it's common in offices and public organizations. Installing vertical blinds will not take much time.

1. It is necessary to make markings for fastening the elements.
2. Next, attach the brackets and cornice.
3. Place runners on the cornice and attach lamellas to them one by one.
4. Attach weights to the control handle.
5. Check the operation of the structure.

Vertical blinds mounting diagram
For detailed instructions on installing vertical blinds, watch the video below:

We install horizontal blinds on plastic windows

In most cases, horizontal slats are attached to the wall. They are able to close the window opening completely, but at the same time they look aesthetically pleasing and do not “squeeze” the space of the room. There are times when they are mounted to a window. Here, the lamella parts are attached to each sash separately. The installation system for horizontal blinds is no different from vertical options:

1. We mark the places for fastening.
2. We attach the brackets.
3. We put a cornice on the brackets.
4. Checking the length.
5. We check the installation and operation of the mechanism.

Mounting diagram

To make sure the steps are correct, watch the instruction video for installing horizontal models.

We install blinds on plastic windows without drilling

If for some reason you do not want to drill a wall or a double-glazed window, you can use tape or special brackets. There are L-shaped brackets that are attached to the surface of the glass unit without drilling. They are easy to install and dismantle thanks to a simple latch. But, they are attached only to those doors that open. To attach the brackets to a closed sash without drilling, use double-sided mounting tape.

Thus, with the help of L-shaped brackets and tape, you can maintain the integrity of the window profile. Fastening with adhesive tape is less reliable than others, but if you do not overload the structure, it will last a long time.

Mounting on brackets

We install roller blinds on plastic windows

Roll models are installed in almost the same way as vertical ones. One of the most available options installation of blinds - on two brackets, which are secured using self-tapping screws.

1. We make markings for the details.
2. We fasten the brackets with self-tapping screws (make sure that they are at the same level, otherwise the blinds will hang crookedly).
3. Next, we attach the cornice with the canvas.
4. We check the operation of the structure.

Mounting diagram for roller blinds
For more details on the nuances of installing roll models, watch this video:

Installation of blinds on wooden windows

Modern models are attached to wooden Euro-windows and old Soviet ones. It’s worth noting right away that when installing on old-style windows, you need to carefully take measurements.

Please note: the glazing bead on wooden Soviet windows should not protrude beyond the plane of the frame!

Among suitable models for wooden windows: isolight, isotra, roller and rollite. These are universal models. They fit harmoniously into the interior design, regardless of its style. Are different simple mechanism management and high performance.

One of the most complex installations for wooden double-glazed windows - fastening to each section. All the necessary parts are included in the headset. Installation principles are the same as for plastic ones: using brackets or screws. If you are not afraid to make a hole in the glass unit, you will be pleased with the result. With the help of fastening with screws, the structure will last a long period of use.

Mounting to brackets is considered less reliable, but it has a huge advantage - no holes in the glass unit. When you want to remove the blinds, there will be no defects left on the window.

We install blinds on wooden windows

Let's take a closer look at the option using drilling and fastening with screws.

1. First you need to make markings for each of the fastening elements.
2. Make sure that the structure does not interfere with the opening of the window sashes.
3. Make holes for the screws. Install screws and dowels.
4. Attach the curtain rod to them.
5. Install another fastener at the regulating thread to relieve the structure from accumulating load on that area.
6. Attach the runners and slats to the cornice.
7. Check the operation of the structure.

Self-tapping screws make it easier to attach the cornice to the window. Self-tapping screws will not cause harm window profile, but work carefully during installation. If you want to remove the slats after a while, no problem. After dismantling the structure, the holes are filled with special silicone glue white– and not a single trace of the screws will remain.

Good to know! To begin with, it is better to drill holes according to the markings, and then mount the parts. Screwing in self-tapping screws individually is one of the causes of cracks. And this installation method guarantees the integrity of the plastic.

When the holes are prepared, the brackets are carefully screwed to them. Then the cornice is installed and closed. The following steps are required:

1. Install the hook into the control mechanism.
2. Install the cane.
3. Attach the tip to the cane.
4. Secure the thread with a knot.
5. Check the operation of the blinds.

Installing the lamella structure is not difficult if you follow all the requirements and work carefully. Also read the installation instructions, which are included with any model.