Modern interiors often done using drywall, which is becoming very common. This is explained by the fact that such facing material has a low cost. Often, with the help of gypsum boards, they not only align ceilings with walls, but also create original niches from plasterboard in the wall, which visually increase the space of the premises.

Using drywall, you can not only level ceilings and floors, but also create original niches in the walls.

In some cases, sheets of finishing material make it possible to expand the usable space of residential premises with specific purpose, including bathrooms. This is possible using sheets of waterproof plasterboard.

Tools and materials for creating a niche

Knowing how to make a niche from plasterboard in the wall of a room, you should prepare appropriate tools with materials, the list of which includes:

1. Special safety glasses.
2. Hacksaw.
3. Building level.
4. Side cutters.
5. Roulette.
6. Pliers.
7. Metal scissors.
8. Hammer.
9. Knife with replaceable blade.
10. Hammer.
11. Putty.
12. Fastening element (dowel-nails).
13. Screwdriver.
14. Bulgarian.
15. Drywall sheets.

Any craftsman, even a beginner, can make niches in a plasterboard wall. The design of the structure is pre-developed, and all dimensions are transferred to the drawing. The master must have an accurate idea not only of how to make a niche from plasterboard, but also of how it will look in the interior of the room.

All this will allow you to make an accurate calculation required quantity material to purchase it without extra costs. At the same time, the use of additional building and finishing materials depends on the design of the niche, for example:

1. Glue.
2. Paint.
3. Dry type construction mixture.
4. Electric tool.
5. Needle roller, etc.

Most easy option It seems possible to install one niche in a wall made of gypsum plasterboard, but it is possible to mount two or more niches in one structure. When planning the placement of a niche in the wall, the cladding of the structure is moved back to a certain distance, which is equal to the size of its depth. The width of the entire structure may not be very large, for example, 15 cm. Installation of a plasterboard niche should begin when the wall is marked according to the diagram. Then the metal profile is installed, taking into account the entire perimeter of the future niche.

Return to contents

How to make a niche from gypsum board with your own hands?

It is convenient to cut a metal profile using a grinder or metal scissors. It is important to set it correctly. For this purpose, a tape measure is used building level. You can strengthen the profile using mounting umbrellas (dowel-nails). When making a niche that is not very wide, you can use a guide profile (NP) or use a rack profile (SP).

Then they move on to assembling the frame. It is more convenient to set the guide profile from the floor of the room. All work is performed using a tape measure, which can be used to measure the required size. Measurements are taken from the surface of the base wall using a tape measure, taking into account the thickness of the plasterboard.

Traditional dimensions of drywall are 2500x1200x12.5 mm. When all the marks are made, they are connected by drawing special lines. It is required to transfer all marks for the ceiling NP (guide profile) using a plumb line. When assembling the frame, installing rack profiles required size produced vertically. The installation of the upper and lower guide profiles is also carried out.

The standard length of the profile is 3 m, so it should be cut. The profile height is measured separately, since it differs by 1-1.5 cm in different areas premises. This is due to the presence of errors allowed during the construction of any premises. Using a level, you should ensure that the racks are positioned strictly vertically.

Only after this the frame elements are secured using dowel-nails. If necessary, assemble the frame using only the guide profile. When making the transition to the floor from the wall, it is enough to make a cut with scissors to bend the profile at an angle of 90 degrees.

Having exposed the profile, it is fixed on the wall, after which the installation is carried out vertical racks with horizontal jumpers between them, taking into account the size of the niche.

Then you should install jumpers from the racks towards the wall. When installing these niches along the entire surface of the wall, it is necessary to create a fairly reliable frame. You cannot do without additional profiles with jumpers alone.

Return to contents

How are wide plasterboard niches for a bed created?

Before creating a niche from plasterboard, you should develop a design so that the metal profile is combined with the gypsum board. For example, furniture walls - slides, which are multi-level, are considered well known. They can be made independently from sheets of drywall.

Select a profile that has the greatest strength. Large niches can be made if you use a profile with a back width of 75 mm. For example, German manufacturer Knauf manufactures reliable products using the thickest metal possible.

To create a frame for the shelves, you can use a piece of profile that is solid. To do this, a frame in the shape of a rectangle is bent from this material, secured to the wall with dowels and nails. In the required place for bending, you can only cut the side of the profile. After this, the adjacent sidewalls are fastened using self-tapping screws or a cutter.

If the frame is of sufficient length, it should be strengthened with crossbars, which are spaced from each other at a distance of no more than 400 mm. Using two frames, you can make a frame for wall cabinet, if you fasten them with jumpers. By securing the frames to the floor using profiles, you can obtain a base for creating a niche in the wall. If these types of structures are combined, you can make them yourself different kinds built-in furniture with niches with shelves.

For creating original designs use a flexible profile, for example, produced by Flext. All its sections include two halves shaped like the letter “L”. They have special locks at the ends. As a result of installation, a profile of the required length is created, which makes it possible to produce a structure with a closed or arbitrary shape. By combining the Flext profile and the usual type of profile, they are used to create a frame for gypsum plasterboard walls with round or oval niches, etc.

In this master class you will find detailed description the process of installing kitchen walls and ventilation according to a finished design project. We will tell you about the features of installing a false wall with a niche using the “from the center” method and give detailed photos this work carried out by experienced specialists.

A plasterboard niche is a popular and effective interior element. She may have different shapes, but invariably emphasizes the taste of the owner of the house. We will tell and show you how to make it yourself.

If you don't have it ready professional project, create a drawing or sketch with dimensions. This way your thoughts and desires will take shape.

Please note that the parameters of the niche in this case are determined by the size of the tiles with which the inside will be lined.

After transferring the marks to the plane of the wall, we begin to secure the guides. This key moment, since further dimensions will be deposited from them.

We create the main frame from the UD profile and check its corners - they must be strictly straight. You can use a tile to check.

Then we cut out and wind the gypsum board strips that will limit the inner plane of the niche.

We install horizontal guides, which we connect to the vertical posts. In this case, the frame is built not from a common plane, but from the center of the element (niche).

Check again how the tile fits in. If there is an error, it is better to eliminate it at this stage.

Attention! When trying on tiles, take into account the putty thickness of 2-3 mm.

Pay attention to the vertical piping of the frame and guides. They are installed after the horizontal stripes.

Thus, fastening and tying the entire structure is much more reliable than if the entire frame was made separately.

We mark horizontal guides under the vertical ribs (step 600 mm).

We install the ribs themselves along the lower guide, first on internal fastenings, and then we place U-shaped suspensions under them.

View of the finished frame without the top row of vertical posts (done in the same way as the bottom one):

We cover the frame with plasterboard using standard technology.

Pay attention to how corners are cut in openings and niches (a convenient method). First, we wrap the entire sheet.

Then we cut it horizontally with a hacksaw.

And use a knife to cut it vertically. This method does not require marking and protects against errors during marking - the gypsum board is cut in place, and one of the planes of the niche serves as a guide.

Final view after installing drywall:

All that remains is to prepare the surface for puttying. We open the corners with a plaster float and the joints with a knife.

Carefully checking the accuracy of the horizontals and verticals, we sew the perforated corner with a stapler.

Final look plasterboard niche:

If in your case there is a need to use a wall to hang something, be sure to install reinforcements - double ribs. At the same time, U-shaped suspensions should be of a different class - more powerful. In the future, the niche can be given any volumetric view using various methods finishing and decorations - tiles, wallpaper, curtains, artificial stone.

In the renovation and decoration of residential premises, a person’s desire for beauty is expressed in different ways - some people want to decorate their home finishing materials incredible colors, others focus on designer furniture, and still others give preference to the structural elements of an apartment or house. In principle, both are partly right; all these methods are designed to improve the comfort of the premises and create coziness in them. But few people understand the fact that the greatest results are achieved exclusively in the process of using all methods at the same time - an apartment or house should have both good furniture, and high-quality beautiful surfaces of walls, floors, ceilings, and, of course, decorative structural elements. We’ll talk about one of them in this article, in which, together with the site, we’ll look in detail at the question of how to make plasterboard niches with your own hands, what material is needed for this and what tools are used to create them.

DIY plasterboard niche photo

How to make a niche from plasterboard: frame construction

As with all plasterboard products, the frame is the main component of the entire structure - the shape, rigidity, reliability and even appearance finished product. The final result depends entirely on how responsibly you approach the construction.

To build a niche frame from plasterboard, you will need three types of materials - these are ud guide profiles, with the help of which the structure is tied to the walls and the contours of the product are formed, cd profiles, designed to impart rigidity to the structure, and sheet thickness 12.5 mm (preferably moisture resistant, but Ordinary is possible).

How to make a niche frame from plasterboard with your own hands

Before you start work, you must clearly understand the full picture of what you want to get in the end - you cannot do without it. You may even have to draw a small sketch or a simple drawing that needs to be transferred to the wall in real size. Drywall outlines drawn on the wall will really make the job easier. You will have to draw everything - every shelf and every curve. The more precise you are, the easier it will be to create it.

Guide profiles ud are installed along the drawn contours. They are secured using dowels and a hammer drill. There will be no problems with straight sections of the structure; difficulties arise when designing radial surfaces - to construct them you will have to learn how to smoothly bend metal profiles. In principle, this is not difficult - to obtain a smooth arc, the guide profile flanges are cut in increments of 50mm. If you don’t want to do this work, then purchase a ready-made arched profile, in which the cuts have already been made at the enterprise. In my opinion this is extra waste money - quite simply (within 2 minutes) cut with a grinder or even scissors.

How to make a niche from plasterboard photo

Okay, let's move on and give our frame volume. In accordance with the required depth of the niche and plasterboard shelves, it is also necessary to install guide profiles on the floor and ceiling - their ends, located on opposite surfaces, must lie in strict vertical level. Along with the volume of the structure, the front plane of the plasterboard niche is also specified, which must be perfectly flat.

DIY installation of a plasterboard niche photo

Now let's start forming the corners - as a rule, they are made from two guide profiles twisted together. Their shelves should be at an angle of 90° relative to each other. These corner elements are installed vertically and are inserted into the upper and lower profiles located on the ceiling and floor respectively. It is imperative to check the level of their installation in two planes at once (on the front and side surfaces). If everything is in order, then you can safely fasten the guide profiles and corner post between themselves - for this, self-tapping screws ø3.5mm by 7.5mm are used (popularly called “tex” or “flea”).

Having given volumetric outlines to the frame, on next stage A DIY plasterboard niche will require you to make it rigid. There is no point in relying on drywall to cope with this task. The frame is simply reinforced - for this purpose the cd load-bearing profile is used. It is cut into small pieces, the length of which corresponds to the distance between two opposite guides, inserted across them and secured with two ties on each side. Again, do not forget to control the level and plane of the resulting surface. Such reinforcement from load-bearing profiles cd on the side faces of the structure will need to be installed with shelves in different sides- in addition to giving rigidity to the frame, they also serve as a basis for screwing drywall. And in such products you have to twist it both inside and outside the niche.

Plasterboard niches in the wall photo

After the frame of the plasterboard niche has been strengthened, you can begin to form the shelves. The principle of their manufacture is almost the same as that described above. First, using ud, a level and self-tapping screws, the plane of the shelf is set, after which it is reinforced with load-bearing profiles, the shelves located up and down, every 300 mm.

Most craftsmen (including me) practice covering it with plaster while making the frame. Before installing the shelves, the entire internal cavity of the niche is lined with plasterboard - believe me, it’s easier to fix one large sheet than to work on its individual pieces. And thanks to this approach, the structure acquires additional rigidity.

You know Golden Rule drywaller? Fewer joints means fewer headaches later. This principle applies to all products, including plasterboard niches.

In addition, this approach to business will help to diversify this tedious and monotonous work a little.

Niches and shelves made of plasterboard photo

An important point in the process of creating decorative niches from plasterboard is its illumination and noise reduction - all this must be thought through at the stage of manufacturing the frame. You need to decide on the location of the lamps and lay the necessary electrical cables, and all inner space frame fill mineral wool. In principle, if you are satisfied with a ringing hum even when objects lightly hit the niche, you can refuse noise reduction - some people are fine with this phenomenon, but some are annoyed by it.

Decorative niches made of plasterboard photo

Installation of a plasterboard niche: framing the frame

This stage of forming a plasterboard niche is quite simple and does not have any special nuances, with the exception of a few, which we will consider later.

1. Firstly, this is docking individual parts drywall. At the junction of individual parts sheet material it is necessary to install additional stiffeners, to which two separate pieces of drywall are screwed. If you ignore this nuance, then during operation you will get a crack in this place, even despite the high-quality sealing of the seams.
2. Secondly, the absence of which again leads to the appearance of cracks. At the junctions of individual sheets of drywall on their cut edges, it is necessary to chamfer.
3. Thirdly, this is the step of installing screws. It is standard and is 150-200mm.

Well, in conclusion, I would like to pay a little attention to decorating the niche, or rather preparing for this process. If you think that you can refuse to putty, then you are deeply mistaken - a plasterboard niche does not require putty only in one case, when it is tiled or tiled. It is this stage of manufacturing a plasterboard niche that is the most labor-intensive - you will have to install a huge amount perforated corners, place dozens of meters of reinforcing mesh in the corners and joints and properly fill even the smallest cavities.

Drywall is one of the most rewarding materials for design. It is quite easy to use and also has wide range applications. With the help of gypsum boards, repairs become easier, faster, and the results are more spectacular. Builders use it to construct ceilings, including several tiers.

Designers design various niches, frames, and partitions. Depending on the area of ​​application, the material is divided by thickness into: wall, ceiling, arched.

Types of plasterboard niches

Niches made of plasterboard are relevant and appropriate in any interior style. They can have several functions:

• decorative, bringing only aesthetic pleasure;
• functional, for example, hiding wires from equipment intended for books, etc.;
• technical, necessary to ensure a smooth approach to something.

The design can be of different shapes:

• vertical;
• horizontal;
• complex geometric shape;
• wavy.

Depending on the desired effect, a specific niche configuration is used. For example, to achieve visual lengthening of walls and objects, horizontal, narrow niches are used; for low ceilings, design vertical ones.

Design ideas

A niche made of plasterboard is an interior detail that is appropriate everywhere: they add relief and depth to the room, and serve extra space for storage or bundled in common geometric lines construction.

Below are just a few design ideas that decorators use most often.

A blank and monotonous wall, devoid of furniture, looks dull. A fresh solution could be a recessed space to accommodate a plasma or framed mirror.

Often they make a series of small 3D decors from gypsum board, about 5-7 cm deep, the width of the building profile and insert photos, candles, vases, etc.

Niche instead of furniture

Drywall is so convenient and durable when the load is distributed correctly that sometimes designers use it instead of furniture.

• Solution in the form shelves for placing books, household items, and equipment you often find in interiors. In this case, different planes are painted in contrasting colors to enhance the effect, and some parts are covered with glass.



• Dressing rooms in hallways also look modern and beautiful from gypsum plasterboard. The shelves can withstand heavy loads and provide additional aesthetic pleasure and ease of use.



• Location arches around the sofa or portals for the fireplace - beautiful and functional. Sheets are used for different planes different thicknesses+ available standard sizes load-bearing profile. Therefore, the minimum depth is the sum of the profile width + sheet thickness + finish.



• Creation mini wardrobe in the bedroom. Interesting design move- constructing a niche in the middle of the room, which is then closed by a sliding door going into the wall. This place is equipped for storing things, like a pantry, etc.



Niche for battery

Drywall is used to create depth for the window, and the radiator is refined, as if visually recessing it into the wall.



Ceiling

Such designs often hide the mechanisms of the cornices, create a multi-tiered top and hide LED backlight. The curtain seems to fall out of nowhere, and hidden lamps add romanticism and some mystery to the room.



Zoning

• Entire structures are constructed from plasterboard. Even half, fenced off with a semi-arch work zone from the bedroom will allow you to get a cozy workplace or just a place for inspiration. When demolishing the original walls and erecting new ones according to the project, the redevelopment should be recorded in the relevant government agencies.



• Zoning is important in children's rooms when there are several children and one room. Psychologically, each person needs to have his own personal corner.



• Division in a studio apartment. Niches in small apartments- the rescue. is able to unobtrusively separate sleeper-sofa from the kitchen. For example, in design development kitchen furniture hidden behind a plasterboard bar counter.



Types of structures

The basic principle of building niches is to first install a U-shaped profile of the required contour. And then fasten the plasterboard sheets on top. The thickness of the latter varies by 12.5 mm, 9.5 mm and 6.5 mm. Based on the above, there are three main design options:

1. Classical. That is, the formation of a frame, and then dressing it with material.
2. For decorative niches 5 cm deep, no columns are used metallic profile, and attach double gypsum boards of the required dimensions to each other. The ends are puttied.
3. Arched option. The arc is made by analogy with in the classic way with minor adjustments. Cuts are made on the profile and it is bent in an arc; a sheet of cardboard plastically follows the rounded contour.

Many people think about how to make a niche out of plasterboard themselves. In fact, it is not at all difficult, the main thing is to stick to the plan. Step-by-step instruction will help you get to your goal - a beautiful and neat plasterboard niche that can decorate any design.

Niche drawing (sketch version)

Information for developing a sketch:

• the depth of the niche in the living room (for installing a TV) is equal to its thickness plus the space that the wires will take up, electrical sockets. The screen should be flush with the edge of the opening. The same applies to other electrical equipment - only its front part should be visible;
• leave gaps on the sides and top of the niche. Your hands must fit freely through them, otherwise you simply will not be able to install the equipment. The gaps will also help to avoid overheating of electrical equipment;
• if the plasterboard niche is not floor-mounted, but built into the wall, then when laying the profiles of its load-bearing plane (the lower part of the niche), you need to take into account the load that it will absorb. It is one thing if there is a vase in a niche, and another if there is an aquarium with water;
• immediately determine where the electrical wiring will go - you will have to connect to it if you:
  • planning niche lighting;
  • you are going to install TV and audio in the opening.

The sketch will give you a visual idea of ​​what a plasterboard niche should look like and will help you calculate required quantity material. The photo shows an approximate sketch of a rather complex niche, inside of which shelves are made of plasterboard.

Sketch of a plasterboard niche

Installation of lathing (frame) from a metal profile

To install the sheathing yourself you will need:

• guide profile ud;
• CD rack profile;
• self-tapping screws (“fleas”);
• screwdriver;
• drill;
• dowels;
• building level, pencil;
• tape measure, plumb line

Tools for working with drywall and profiles

The main rule of the finisher: if you don’t want any alterations, use a building level. We set the rear plane of the frame according to the sketch dimensions and screw the guide profile onto the floor, walls and ceiling with dowels. In this “frame” we insert and fasten the vertical cd profile in increments of 50 - 60 cm. If the wall is lumpy, then the ud profile is attached to U-shaped hangers. At the junction of the rack and guide profiles, the metal is held together with “fleas”.

Front plane of the frame. We set aside the distance from the already mounted rear plane of the frame equal to depth niches. We draw a line along which the front plane of the frame will pass. Assembling the front frame.

Marking a plasterboard niche should be carried out in accordance with the horizontal level

We strengthen both flat frames with horizontal jumpers from the UD profile. We cut it into equal pieces and insert them between the vertical profiles. We fasten the intersections with two self-tapping screws. Don’t forget, in the place where you decide to make a niche, the profiles should form “windows”.

We make the frame a three-dimensional structure. We connect the front and rear planes of the frame with jumpers (ud profile). Pay attention to the photo. In places where the frame forms a niche, the profile is placed two at a time, and its shelves are turned away from each other. This gives the structure additional rigidity.

When assembling the frame, it is necessary to control each stage of work with a level, since the slightest discrepancy at the beginning of work can ultimately ruin the entire structure
Frame for a niche made of gypsum plasterboard

Electrical connection

Are you planning to make your own lighting? Start now, before the frame is covered with drywall.

Decide on the type of lighting:

• halogen spotlights, if the opening will be illuminated by several “halogens”, then it is better to place them in equal increments, the size of which depends on the power of the lamp. Connecting wires when connecting spotlights occurs using terminal blocks. At one end, the stripped wires of the lamp are inserted into this device, and at the other - the electrical wiring cable;
• LED strip practically does not heat up, is economical, but is quite expensive. It is connected via a power supply, which most often has to be purchased separately. Be careful when connecting - you will confuse “+” and “-” and the tape will burn out. The LED itself is attached to a sticky layer applied to one of its sides;
• If a plasterboard niche will be illuminated by an overhead lamp, then the frame must be provided with embedded profiles to which the lamp frame will be attached.

Electrical cables are hidden in corrugated hoses (according to the requirements of the PUE). To attach the corrugation to the wall or ceiling you will need clips (fasteners) and dowels.

Lamps for decorative niches

Cutting and covering the frame with plasterboard

The simplest of the stages is for those who do everything with their own hands, but this is where novice craftsmen make mistakes. Cutting will require all your accuracy and scrupulousness. Make a mistake in transferring dimensions, and a sheet of drywall may go to waste. For work you will need: tape measure, drywall knife, strip, pencil. Then everything is simple:

• put the sheet on the table and mark the outline of the future part;
• cutting: do not use much force - cut the paper and the plaster will break easily. We cut through the paper on the other side. Separate the part.

Options for cutting drywall. 1 - plane for drywall; 2 - knife for drywall; 3 - hacksaw for drywall; 4 - jigsaw

In order to sheathe the frame you will need: a screwdriver and self-tapping screws 25 - 40 mm long. The fastening pitch with self-tapping screws is taken to be no less than 250 mm, and in the niche area - no less than 150 mm. We retreat about 1 - 2 cm from the edge of the sheet. When sheathing the frame, make sure that the edge of the part lies on the profile - if you leave it to “sag”, a crack will definitely appear in this place.

Sheet end processing

There are many places in niches where sheets of drywall meet at right angles. The ends of such sheets must be chamfered at an angle of 45°. An edge plane for drywall will speed up this stage of work by an order of magnitude. After the edge is cut, some builders also sand the bevels with a roughing plane or hand rasp.

The edges of sheets that are butt-joined are processed at an angle of 25°. Why is this necessary? When filling a niche, a bump forms at the junction of the untreated edge. To level it later, you will have to apply a thicker layer of finishing putty. This is hard work if you do everything yourself, so they chamfer the ends of the sheets.

Processing the end of drywall with a roughing plane

Primer and putty

The order is as follows:

• we prime all the joints of the niche;
• We cover the joints with starting putty with the consistency of sour cream. Lightly mark the joint with a spatula and apply fiberglass reinforcing tape over the putty. We “smear” it into the mixture. Don’t forget to seal the heads of the self-tapping screws, of which there are especially many in the niche area;
• The second layer of the starting layer of putty is applied the next day. After drying, the joints are cleaned;
• the finishing putty mixture is applied.

To make the plasterboard niche look neat, the internal and external corners it needs to be closed perforated corner. It “sits” on a thick starting layer. The excess is removed with a spatula. The photo already shows installed corner, covered with reinforcing mesh.

Angles plasterboard structures susceptible possible damage, therefore, a perforated corner is used to protect them

Niche decor

To decorate a niche in a plasterboard wall, you can use any decorative coating - paint, mirrors, wallpaper, beautiful fabrics. There are a few simple tips, which will be useful to you.

• give preference light colors- dark openings on light walls will look like holes in cheese. Most often, plasterboard niches are painted the same color as the walls, or 1-2 shades darker. Only if the recess is well lit can rich, dark tones be allowed;
• the mirror finish of the opening visually expands its space;
• color design niches within the room should be the same.

Kitchen

Kitchen openings, first of all, carry a functional load, and only then serve as interior decoration. Microwave, refrigerator, sometimes washing machine- the kitchen is literally stuffed with appliances, all of varying sizes. But if you hide all this equipment in niches made of plasterboard and leave only the facades visible, then the room will acquire a clear geometry - without protrusions and voids. What about pots, jugs, cups, glasses? Let's make several niche shelves along the length of the kitchen with our own hands, and all these utensils will fit perfectly there. An example of this is the photo below.

Living room

Most often, niches are made in the living room to install a TV panel, video and audio equipment. The photo shows that it is design solution hides a wiring harness under the drywall, which so spoils the interior of the living room. Mount the sockets behind the equipment, in back wall opening. You won’t be able to get a full-fledged bookcase made of plasterboard, but a niche-shelf made with your own hands will hold up just fine with a dozen or more of your favorite books.

It happens that plasterboard niches are equipped for the installation of aquariums. But! It is better not to install large-volume aquariums in them. No matter how well you strengthen the load-bearing plane of the opening, under the weight of a large aquarium the profile may bend and the sheet may crack. By the way, do not forget to leave a place above the aquarium for its maintenance and cover it with a decorative panel.

Bedroom

In the bedroom there is almost always an opening at the head of the bed. Here they hang pictures, panels, glue photo wallpapers, or simply provide lighting. But, do not forget that this is decorative, not general lighting - do not place powerful lamps in the recess. If the opening is deep, decorate its space in the form of niche shelves. There will be a place for your knitting, books or mobile phone.

In small decorative niches made of plasterboard, in the bedroom or living room, you can put flowers, vases, souvenirs. The photo shows how original the collection of small paintings looks in the illuminated openings.

Design "tricks"

Design techniques include:

• a vertical niche from floor to ceiling will not make your ceilings high, but it will create the desired impression;
• horizontal openings visually lengthen the walls;
• plasterboard niches are never framed;
• the shallower the depth of the opening, the smaller the objects located here should be;
• The photo below shows one of design techniques. This color scheme visually deepens the living room niche and makes it voluminous.

We hope our instructions on how to make a niche with your own hands will help you in the difficult task of installing plasterboard structures.