Homemade products from the bridge of vases. Homemade trailer for a walk-behind tractor from the Zhiguli bridge. Making a fender liner for a walk-behind tractor (protection from dirt)

To cultivate a plot of land requires a huge amount of physical effort. For some farmers physical work gives pleasure, so they are quite satisfied with basic tools at work. But most summer residents for plowing acres on personal plot they use walk-behind tractors, which are often assembled with my own hands.

Design features

A homemade walk-behind tractor is most often used to perform simple but labor-intensive work:

  • plowing of land;
  • hilling up plantings;
  • mowing grass or tops;
  • application of organic fertilizers.

You can upgrade any walk-behind tractor with a ZiD engine or any other, make it on large wheels, with a belt drive.

Often, craftsmen prefer to reassemble such units using old spare parts from such mechanical devices:

  • chain saws of the “Friendship” type;
  • scooter;
  • motorcycle;
  • washing machine.

An electric motor may also be required in this technique, for example, to create air cooling, so the motor is from a vacuum cleaner or small refrigerator may also come in handy.

If a person owns a tool and understands the structure of equipment, then making a walk-behind tractor is not difficult. In terms of material costs it may cost minimum amount, while prices for good unit start at $300. If everything is done correctly, a new device created by yourself can be in no way inferior in reliability and performance to imported models such as Cayman walk-behind tractors.

Often craftsmen use old units from the Druzhba saw as engines. At the same time, the walk-behind tractor is easy to operate; even a non-professional or a minor can work with it. The power plant is able to withstand significant loads without stalling even at low speeds.

This indicator is important for the following work:

  • plowing;
  • harrowing;
  • harvesting.

Even branded walk-behind tractors cannot perform such work.

Advantages and disadvantages

The advantage of a homemade walk-behind tractor is that it can be made based on the needs that exist in a given farm. For example, a practical unit should do most of the work on plowing and harrowing. In accordance with these “requests”, the right size frame, the engine is adjusted so that it runs at low speeds. It is necessary to put in order the knot that secures attachments.

One of the disadvantages is that it is not always possible to perfectly fit all the blocks taken from different mechanisms to each other with your own hands.

In order for all the components to work together, you need to be fluent in many engineering professions and have a fair amount of practical experience.

How to do it?

The example that will be given below (master V. Arkhipov) will be a good illustration of how you can assemble an all-wheel drive walk-behind tractor at home with your own hands. The cables can be taken from the Ant, ZAZ, scooter, the rear axle from the VAZ, the box from the Zhiguli.. The main frame is made from pipes with a diameter of 40-45 mm. Modular hinges are installed as rods, which will be reliable " link» between the power unit, plow and steering wheel.

Another tube is welded onto the supporting frame, which ends with an axis. In this way, the tension of the cables going to the box is challenged. Tension is realized using a moving lever.

This unit has a number of advantages. First of all, we should mention the hinge block. A non-dynamic rigid connection (which is present in many models) makes the mechanism difficult to operate. Articulating joint is more productive– you can change the direction of movement during the plowing process, while the plow can remain in the furrow.

This topic is quite relevant, because due to soil resistance the car is constantly “driving” in different sides. Additional attention and effort are often required to “keep” the mechanism exactly on course.

The axis of the device is arranged according to the vector of translational motion. During plowing, the entire block is slightly “rotated”. Moreover, the optimal angle can actually be corrected using the articulated rods.

Plowing depth can be maintained automatically. It should be said that the frame is equipped with a field board. It regulates the force that is responsible for driving the plow into the ground, especially when it burrows. If it protrudes from the ground at too large an angle, then the angle of attack increases accordingly, then the unit again enters the soil by a given amount.

The future walk-behind tractor is equipped with a supporting frame and wheels, which can be made of metal; they will have good grip on any soil. To reliably “couple” the frame with the suspension, two bent tubes are usually used, between which a fuel tank is mounted.

To properly equip the engine, a bracket is used, at the end of which there is a steel axle (its length is 15 cm).

A bracket is welded to the frame itself, and the engine is placed on the axle. The entire power block is fastened with arcs. Upon completion, another shaft is installed, control cables and chains are pulled.

Such a unit can perform many various works and be a universal device. To do this, it is enough to simply replace the spare parts intended for the plow with the elements necessary for the functioning of the cultivator.

While moving, the unit deepens a furrow in the soil and at the same time places potato tubers there. To “close” the tubers, you should simply use the walk-behind tractor a second time. The algorithm for hilling plants is exactly the same.

The use of different blades allows you to adjust the working width; it is also possible to “pick up” potatoes that were not collected during the first pass. The walk-behind tractor can be used for cleaning snow and wet leaves; you just need to “pick up” the hard brush.

Any walk-behind tractor consists of the following components:

  • engine;
  • transmission;
  • controls;
  • gearbox;
  • aggregation system.

It is best to choose a two-stroke engine; a motorcycle engine from IZH-Planet is ideal for this.

Transmissions in walk-behind tractors are as follows:

  • gear (it can be found most often on tractors or tanks);
  • gear-worm;
  • complex (gear and worm) with an additional pulley.

System various elements management contains:

  • switching speeds;
  • gasoline supply;
  • brake.

The control unit consists of several levers that are responsible for:

  • speed switching;
  • fuel supply to the engine;
  • brake.

The mechanism must be equipped with an aggregation device that ensures reliable coupling with mounted equipment.

Required materials and tools

To assemble a walk-behind tractor yourself, you will need certain practical skills, as well as some engineering knowledge.

The tools you will need are:

  • welding machine;
  • grinder;
  • drill;
  • keys;
  • screwdrivers.

Consumables also needed:

  • nuts:
  • bolts;
  • counter washers.

As for materials, you will need:

  • pipes;
  • corners;
  • brackets;
  • metal sheet 5 mm thick.

Step-by-step instruction

Correct assembly begins with studying the drawings and layout of the frame, which consists of pipes with a diameter of 45 mm. The control unit is attached to the rear of the frame. In front will be the transmission and battery, which will be mounted on a small metal platform.

The motor is attached to the corners, which are welded to the frame. A cross member is welded between the corners; it will serve as a “stand” for the engine. Holes are drilled in the corners for fastening the units with bolts.

An important point is correct installation gearbox It is usually placed between the wheel and the power plant.

Often, part of the energy of a rotating element is transformed using a gearbox to attachments. The engine is cooled using air flow, for this purpose an additional electric motor is installed, which has a power supply of 12 volts.

The wheels have a diameter of 12 cm. Chains are sometimes put on the wheels for better traction with the ground.

The muffler can be used from a moped or scooter, or you can make it yourself. An important component is the small adapter that connects the pipe to the muffler. It must be made by a turner or mechanic.

The fuel tank can be made from an ordinary canister. It is enough to make a hole in it and solder the hose (you can use cold welding). All available materials are easy to get, they are inexpensive, but some components will need to be turned, that is, ordered from qualified specialists.

You can rent a welding machine and do the welding yourself.

Is it possible to make a walk-behind tractor with your own hands from the rear axle of a VAZ? It will not be possible to assemble a full-fledged walk-behind tractor, but this unit will make an excellent trailer for agricultural machinery. Of course, we will have to make a number of changes to the bridge design, but this will help us in the future to correctly assemble a new trailer frame.

Assembling a walk-behind tractor from scratch

If you are going to construct an entire walk-behind tractor with your own hands, or even an entire mini-tractor, before starting work you should think about the feasibility of implementing such a project. The modern market can offer the user many models of domestic and made in China, whose characteristics allow for work of low and medium difficulty. Moreover, the price of such equipment is quite affordable for many users. So the project to create your own walk-behind tractor should have the following advantages:

  • low cost;
  • the possibility of using old spare parts from equipment, cars or motorcycles when assembling;
  • improved performance compared to the factory equivalent;
  • additional functionality.

The project is worth implementing if at least 3 of the listed points have been met. Otherwise, the idea is not worth the cost and it is easier to buy a ready-made walk-behind tractor, even a used one, with subsequent updating of parts.

Now about the design. You need to find a drawing according to which the homemade product will be assembled. The drawing will indicate the main parts, features of their installation, as well as the method of manufacturing fasteners for spare parts. Without documentation, it will be impossible to implement the project, so the primary task is to find the most suitable drawing. After this, you can begin selecting materials.

Parts, assembly of new units and complete set of walk-behind tractor

Unfortunately, not many parts can be used from an old VAZ for a walk-behind tractor. Here is a list of what will be useful in one case or another:

  • engine, since the Zhiguli has a gasoline engine, this option is not the most economical;
  • fuel tank and fuel system parts;
  • exhaust gas removal system;
  • air filter;
  • starter;
  • steering wheel, gas and clutch levers;
  • gearbox, transfer case;
  • wheels;
  • rear axle - useful for assembling a trailer structure.

In fact, this is everything that can be used from VAZ. Homemade walk-behind tractor from the Zhiguli Bridge and similar models It is very difficult to make a VAZ without many transformations, so you have to use only individual parts of the chassis.

Usually the engine for a walk-behind tractor is a diesel one, so it’s worth delving into old motorcycle equipment, for example, the same motorcycle. There are some homemade products with saw motors, but they are used for light earthworks.

The choice of engine is very important, so focus on the type of work that will be performed by the walk-behind tractor. For medium loads with plowing the land and harvesting crops, a motorcycle engine is sufficient, but for more labor-intensive work, a car engine will be required.

In some cases, if there are not enough parts, you can buy original spare parts for walk-behind tractors and use them in the design. This option should be considered only if the drawing contains recommendations and examples for converting purchased spare parts.

Since we need to get a working prototype, try to follow all instructions as closely as possible and carry out all work according to the diagram and drawings.

Mini tractor

A mini tractor differs from a walk-behind tractor in that its power is higher, which means that the scope of application of equipment on the farm increases and changes. You can quite easily make a mini tractor from walk-behind tractors by connecting a suitable trailer. Here you can use it like factory model walk-behind tractor, and its homemade analogue. You will get this kind of walk-behind tractor from a Zhiguli bridge and with a trailer. You should still choose a diesel engine, preferably a more powerful one. This assembly option also involves the use of a special drawing.

The Zhiguli will benefit from not only the rear axle, but also the gearbox. Some modifications will be needed:

  1. The top of the gearbox is cut off, and it is bolted to a homemade frame. The pulley ratio is maintained at 1:4.
  2. A chain drive is pulled from the gearbox to the axle, and adjusting sprockets are installed with an efficiency ratio of 1 to 3.8.
  3. The bridge itself is bolted to the walk-behind tractor frame.
  4. The wheels are made from Zhiguli wheels. You can disassemble the structure along the weld seams, and then narrow the disk itself by inserting a smaller part into a larger one and scalding the resulting part by welding.

The option involves the use of 2 ready-made units: a walk-behind tractor and a trailer.

Using the VAZ rear axle

What you can definitely make with your own hands is a multifunctional trailer from the rear axle of a Zhiguli.

To do this you will need a few materials:

  • steel tubular blanks 60x30 and 25x25 mm;
  • wheels and springs from the rear axle of a Zhiguli;
  • sheet pieces of steel from 0.8 mm thick;
  • channels, duralumin sheets from 2 mm thick.

The trailer body can be assembled different ways. One of the most common options is wooden with metal corners and screw fastenings. The working process is as follows:

  1. The wooden frame is attached to metal structure rear axle.
  2. Metal parts are welded together.
  3. The transverse crossbars are made from a 25x25 mm profile; tubular blanks are useful for the spars.
  4. From 25x25 mm corners we make a metal frame for the frame and weld it to the lower bridge.
  5. Next, the beams are connected.
  6. Using springs we connect the spars to each other. To do this, the edge of the springs is carefully placed on the axis of the beams. WITH central part The structure of the beam is connected by stepladders.
  7. The last part is a triangular drawbar, which is welded from metal pipes. The drawbar is welded to the metal frame.

All that remains is to build a transition from the trailer drawbar to the walk-behind tractor.

Conclusion on the topic

It is not possible to use the entire Zhigul to assemble a walk-behind tractor. The most necessary parts of the structure from this VAZ model: rear axle, which is used mainly for trailers; checkpoint; exhaust system and gas tank.

All other spare parts are practically useless. It will take a long time to look for a suitable drawing in order to make the most of an old Zhigul in the form of a new agricultural machine. But there are similar projects, and they have been successfully implemented by other craftsmen; all that remains is to find the necessary drawings.

Many people are interested in whether it is possible to make a walk-behind tractor with their own hands. A heavy walk-behind tractor or compact-sized walk-behind tractors are indispensable assistants in agriculture, but not all farmers and summer residents have the opportunity to purchase such equipment. Therefore, if you have certain skills, knowledge and skills, you can assemble a walk-behind tractor with your own hands. In order for a self-assembled motor cultivator to serve for a long time, a project diagram is created. It is necessary to correctly measure the parts, purchase materials and tools, and complete technical drawings and dimensions of components. You can use one of the instructions from folk craftsmen who write on special forums on how to make a walk-behind tractor with your own hands.

Any recommendations on the Internet on how to make a walk-behind tractor yourself should be checked against reviews. It’s good if the users of such homemade walk-behind tractors are friends or acquaintances. Then their reviews can be trusted; in other cases, all advice on assembly and use homemade devices need to check.

How to assemble a walk-behind tractor yourself

Let's look at how to assemble a walk-behind tractor with your own hands. Parts that can be used for DIY are taken from old motorcycles and scrap metal. As an engine that is often installed on homemade motor cultivators, you can use the motor from Druzhba - chainsaws.

This engine has sufficient power to allow the use of various attachments. This significantly expands the functional use of motor cultivators. Many people install the engine from the Ant scooter on their walk-behind tractor, which has excellent characteristics and parameters for working in their summer cottage.

To create a walk-behind tractor at home, you will need the following spare parts and materials:

  • Steel corners measuring 36x36 mm or pipes 60x50x2 mm. From these parts you can assemble a frame for a walk-behind tractor.
  • Engine fully assembled.
  • Fuel tank.
  • Exhaust system.
  • Air filter.
  • Kickstarter.
  • The steering wheel on which the clutch and gas handles should stand.

The following tools will help you make a walk-behind tractor with your own hands:

  • Welding machine.
  • Drill.
  • Vise.
  • A set of horns and spanners.
  • A grinding machine on which a special disk must be installed for cutting metal.

Scheme for creating a walk-behind tractor

A homemade walk-behind tractor from a ZAZ gearbox consists of 2 wheels, is self-propelled, and is assembled with an engine that has forced cooling of the cylinder head. It is carried out using air. The motor must be selected so that it can work at different speeds, including small ones, and was capable of performing large volumes of work. You can install a motor from a scooter and remove other elements from it:

  • control cables;
  • engine mounts;
  • handles;
  • chains;
  • arc, frame.

The brakes on the walk-behind tractor are used both factory-made and our own. Homemade brakes will allow you to take into account the necessary parameters and loads.

Having everything you need at hand, you can make a homemade mini-cultivator at home quickly and without any problems. A walk-behind tractor based on the ZAZ gearbox is created as follows:

  1. A U-shaped frame is made from pipes.
  2. On lathe you need to grind the wheel axle.
  3. Make 3 homemade hinges that are installed on the front and control rods. This approach to assembly was used by designer Arkhipov when he made his walk-behind tractor. Hinges were used to connect the cultivator, steering wheel and plow.
  4. Weld onto the car frame steel pipe, on which the axis should be. It is needed to carry out the tension that is transmitted to the gearbox. In order for such tension to be constantly present, it is necessary to make a rocker arm.
  5. Weld the gear shift knob. A small piece of steel pipe is suitable for these purposes.
  6. The chassis can have chain pitches of 12.7 and 15.9 mm. The sprockets on the chain have the following characteristics: output shaft - 11 mm, secondary shaft - 60 and 20 mm, running axle - 20 mm.

The main stages of manufacturing a walk-behind tractor:

  1. The frame is welded, on which the engine must then be installed, 2 pipes in the form of an arc.
  2. The fuel tank is attached between them.
  3. We assemble the motor using a bracket, which is also welded to the frame.
  4. You need to attach a motor with suspension to the axle, and then all the parts are connected to the frame arches.
  5. The secondary shaft is mounted.
  6. Control cables are being pulled.
  7. The chains are stretched.

Transmission and clutch

A self-made motor cultivator based on a VAZ gearbox or based on a manual transmission must have an excellent transmission. It is needed in order to transmit rotating torque from the motor to the wheels, change the speed and direction of the machine. This part of the walk-behind tractor consists of units that are connected in series to each other:

  • gearbox;
  • differential;
  • clutch;
  • Transmission.

Gearboxes and gearboxes are divided into several types:

The most optimal solution- installation of a gear transmission on the walk-behind tractor, which has several forward and reverse speeds.

In motor-cultivators, you can use transmissions that consist of 2 gearboxes - a gear (mounted on top) and a worm (mounted on the bottom). This design is suitable for light and medium-sized machines, but for heavy walk-behind tractors it is necessary to install more modernized versions.

The gear-worm transmission can be equipped with a centrifugal automatic clutch. The belt drive on gearboxes of this type can also act as a clutch, which performs its functions through a tension roller and a control mechanism (rod and levers).

An important part of the transmission and clutch is the release bearing. The speed of torque transmission depends on the release bearing.

Chassis and steering

The chassis is a frame onto which all parts of the walk-behind tractor and wheels must be attached. When there is no frame, its functions are performed by the transmission, and the motor and wheels should be mounted on it.

On chassis You can install parts from a car, for example, from the rear axle of a Zhiguli.

This suitable option in order to change the distance between the wheels and set the track of the desired width. If there is no rear axle from a Zhiguli, then one from an Ant or an all-terrain vehicle will do.

It is customary to use 2 types of wheels on walk-behind tractors:

  1. Pneumatic.
  2. Weighted metal ones that have lugs. They are bolted to the wheels or welded on. Additionally on metal wheels you can attach other weights to increase the weight of the walk-behind tractor and improve traction with the ground.

The walk-behind tractor is controlled through a system of levers, gear shift rods and steering wheel. Some models have operator seats, but the vehicle is generally operated manually only. Position necessary designs possible on the following nodes.

On the left side of the steering rod there is a control lever for the clutch and emergency engine stop.

On right side gas, wheel drive and brake levers are installed.

Zhigulevsky shortened rear axle for a homemade walk-behind tractor

To build a homemade walk-behind tractor, you can use the rear Zhiguli axle (from a VAZ car), but for this it needs to be shortened. This is done simply: the axle shafts are cut, as well as the bridge body itself, of course this is all done separately and a piece is cut out. Then everything is welded, that is, the axle shafts and parts of the rear Zhiguli axle housing. Everyone chooses the appropriate track width for their homemade walk-behind tractor. In the photo, each axle shaft of the Zhiguli bridge from the VAZ-2106 car was shortened by 287 mm and as a result, the track of the homemade walk-behind tractor will be 700 mm, taking into account the width of the wheels (that is, from the middle of the wheels). It is planned to install Zhiguli wheels on this homemade walk-behind tractor. View the walk-behind tractor assembled with the engine from the Minsk motorcycle and the rear axle from the six (copy the address (select and simultaneously press Ctrl+c) and paste it into the browser window (Ctrl+v):
motoblok.populjarno.com/photo/motoblok_svoimi_rukami/tormoznoe_ustrojstvo_dlja_motobloka/zhigulevskie_kolesa_na_samodelnom_motobloke/10-0-124


Open photo Shortened rear axle of a VAZ-2106 car in enlarged form. If this is a drawing or diagram of a device, you can download it to your computer by opening it in large size and using the "Save picture as" function (right mouse button).
Please rate this material by highlighting the appropriate number of stars.

Most often, together with this material on the topic

"for a homemade walk-behind tractor"

You can view all photographs, drawings, pictures and diagrams from the category “Motoblocks from cars” by clicking on link. You will find even more materials with descriptions of how to make your own motor cultivator and accessories for it in the section “ Photos of homemade walk-behind tractors» or by making a selection from all materials on the site motoblok.populjarno.com according to the following MARKS:
from a car, wheel axle, Mechanisms, Gearbox.

Perhaps what you are looking for is in one of the most viewed sections of our website:

DRAWINGS AND PHOTOS OF HOMEMADE MOTOR-BLOCKS and ATTACHMENTS
(CLICK ON THE PICTURE or title):

Mini tractors are becoming increasingly in demand in the agricultural industry. This is understandable, because most models show fairly high power levels, which, together with enviable maneuverability characteristics, show the final quality standard. But such a device can always be made with your own hands from oka.

For owners of small land holdings, such equipment becomes completely an indispensable assistant in work, because the use of large-sized units in such areas is impractical and quite expensive. However, not every farmer can afford to purchase a ready-made mini tractor in a store.

The reason for this is the rather high price of such equipment, which consists of many factors. Therefore, more and more often you can find various homemade options manufacturing mini tractors based on a wide variety of equipment.

The understandable desire to save money pushes people to certain constructive experiments, the end result of which will be a mini tractor that is quite suitable for use.

At the same time, the base of such units can be the most various techniques, which is quite common in the households of many rural residents and farmers.

Areas of use

Due to the fact that homemade mini tractors are in many ways identical to store-bought versions, such as, according to the most various criteria, their scope of use will also be quite similar.

Any such equipment is manufactured exclusively for use in the agricultural sector, where the main requirement is ergonomics and reliability of the units.

Is it possible to make a walk-behind tractor with your own hands from the rear axle of a VAZ? It will not be possible to assemble a full-fledged walk-behind tractor, but this unit will make an excellent trailer for agricultural machinery. Of course, we will have to make a number of changes to the bridge design, but this will help us in the future to correctly assemble a new trailer frame.

Assembling a walk-behind tractor from scratch

If you are going to construct an entire walk-behind tractor with your own hands, or even an entire mini-tractor, before starting work you should think about the feasibility of implementing such a project. The modern market can offer the user many models of domestic and Chinese-made walk-behind tractors, whose characteristics allow for work of low and medium difficulty. Moreover, the price of such equipment is quite affordable for many users. So the project to create your own walk-behind tractor should have the following advantages:

  • low cost;
  • the possibility of using old spare parts from equipment, cars or motorcycles when assembling;
  • improved performance compared to the factory equivalent;
  • additional functionality.

The project is worth implementing if at least 3 of the listed points have been met. Otherwise, the idea is not worth the cost and it is easier to buy a ready-made walk-behind tractor, even a used one, with subsequent updating of parts.

Now about the design. You need to find a drawing according to which the homemade product will be assembled. The drawing will indicate the main parts, features of their installation, as well as the method of manufacturing fasteners for spare parts. Without documentation, it will be impossible to implement the project, so the primary task is to find the most suitable drawing. After this, you can begin selecting materials.

Parts, assembly of new units and complete set of walk-behind tractor

Unfortunately, not many parts can be used from an old VAZ for a walk-behind tractor. Here is a list of what will be useful in one case or another:

  • engine, since the Zhiguli has a gasoline engine, this option is not the most economical;
  • fuel tank and fuel system parts;
  • exhaust gas removal system;
  • air filter;
  • starter;
  • steering wheel, gas and clutch levers;
  • gearbox, transfer case;
  • wheels;
  • rear axle - useful for assembling a trailer structure.

In fact, this is everything that can be used from VAZ. It is very difficult to make a homemade walk-behind tractor from a Zhiguli bridge and similar VAZ models without many transformations, so you have to use only individual parts of the chassis.

Usually the engine for a walk-behind tractor is a diesel one, so it’s worth delving into old motorcycle equipment, for example, the same motorcycle. There are some homemade products with saw motors, but they are used for light earthworks.

The choice of engine is very important, so focus on the type of work that will be performed by the walk-behind tractor. For medium loads with plowing the land and harvesting crops, a motorcycle engine is sufficient, but for more labor-intensive work, a car engine will be required.

In some cases, if there are not enough parts, you can buy original spare parts for walk-behind tractors and use them in the design. This option should be considered only if the drawing contains recommendations and examples for converting purchased spare parts.

Since we need to get a working prototype, try to follow all instructions as closely as possible and carry out all work according to the diagram and drawings.

Mini tractor

A mini tractor differs from a walk-behind tractor in that its power is higher, which means that the scope of application of equipment on the farm increases and changes. You can quite easily make a mini tractor from walk-behind tractors by connecting a suitable trailer. Here you can use both a factory model of a walk-behind tractor and its homemade analogue. You will get this kind of walk-behind tractor from a Zhiguli bridge and with a trailer. You should still choose a diesel engine, preferably a more powerful one. This assembly option also involves the use of a special drawing.

The Zhiguli will benefit from not only the rear axle, but also the gearbox. Some modifications will be needed:

  1. The top of the gearbox is cut off, and it is bolted to a homemade frame. The pulley ratio is maintained at 1:4.
  2. A chain drive is pulled from the gearbox to the axle, and adjusting sprockets are installed with an efficiency ratio of 1 to 3.8.
  3. The bridge itself is bolted to the walk-behind tractor frame.
  4. The wheels are made from Zhiguli wheels. You can disassemble the structure along the weld seams, and then narrow the disk itself by inserting a smaller part into a larger one and scalding the resulting part by welding.

The option involves the use of 2 ready-made units: a walk-behind tractor and a trailer.

Using the VAZ rear axle

What you can definitely make with your own hands is a multifunctional trailer from the rear axle of a Zhiguli.

To do this you will need a few materials:

  • steel tubular blanks 60x30 and 25x25 mm;
  • wheels and springs from the rear axle of a Zhiguli;
  • sheet pieces of steel from 0.8 mm thick;
  • channels, duralumin sheets from 2 mm thick.

The trailer body can be assembled in various ways. One of the most common options is wooden with metal corners and screw fastenings. The working process is as follows:

  1. The wooden frame is attached to the metal structure of the rear axle.
  2. Metal parts are welded together.
  3. The transverse crossbars are made from a 25x25 mm profile; tubular blanks are useful for the spars.
  4. From 25x25 mm corners we make a metal frame for the frame and weld it to the lower bridge.
  5. Next, the beams are connected.
  6. Using springs we connect the spars to each other. To do this, the edge of the springs is carefully placed on the axis of the beams. The beam is connected to the central part of the structure with stepladders.
  7. The last part is a triangular drawbar, which is welded from metal pipes. The drawbar is welded to the metal frame.

All that remains is to build a transition from the trailer drawbar to the walk-behind tractor.

Conclusion on the topic

It is not possible to use the entire Zhigul to assemble a walk-behind tractor. The most necessary parts of the structure from this VAZ model: rear axle, which is used mainly for trailers; checkpoint; exhaust system and gas tank.

All other spare parts are practically useless. It will take a long time to look for a suitable drawing in order to make the most of an old Zhigul in the form of a new agricultural machine. But there are similar projects, and they have been successfully implemented by other craftsmen; all that remains is to find the necessary drawings.

who made homemade trailers for the walk-behind tractor, what hubs and wheels were installed

Vladimir (Ansbert)  What you have is what you get.

Leonid (Addalyn) SO AS NOT TO SHARPEN. WE WELD MOSKVICH AJUNCTIONS WITH HUBS

Sergiy (Upendra)  On the trailer of my MB, there is a rear beam "Moskvich" -2141, assembled

Alexander (Thomason)  it will be hard

Vasily (Agharna)  The most best option This is a trailer made from a scooter almost all the year, you just need to remove all the excess and weld a drawbar instead of the front end and you’re done.

Well, if the problem is with a scooter, then a good option is with rear suspensions from a front-wheel drive car, for example, from our nine.

Sergey (Bruno)  Front from Zaporozhets

Sergey (Bruno)

Sergey (Bruno)  Front from Lada

Sergey (Bruno)

Sergey (Bruno)

Vyacheslav (Dulcinea)  I have wheels from 3D, what hubs can they be connected to and how to make a brake

Ivan (Sealey) Wheels and hubs from agricultural machinery 4, 50x10 but no brakes.

Sergiy (Upendra)  It’s a bit difficult, depending on which MB it is for. I have a "Chinese" 8-horsepower diesel. The MB itself weighs 220 kg, the trailer 300, a total of 520, but it pulls a ton, it’s been tested, but this is in an emergency, and I’ve been driving in the range of 500 - 700 kg for 3.5 years now. We have very popular 8-10 horsepower, 6-speed “Chinese” diesel engines, viscous, durable, and easy to maintain.

Gennady (Honoura)  I took hubs and brake mechanisms from a VAZ 2109 homemade trailer weighing about 100 kg. carries with confidence. 500 kg. cargo

Gennady (Honoura)  rear hubs.

Anatoly (Kellie)  Great idea, generally perfect rear axles from front-wheel drive cars, you can make hydraulic brakes using the master cylinder from the clutch of the same VAZ - a classic, and you can also make a handbrake.

Sergey (Bruno)  but if you install a drive axle from a VAZ and make a drive from a PTO, then any mountain is nothing, but it goes through the mud like a tank.

Sergey (Bruno)  BUT! ON HARD SURFACES MUST BE TURNED OFF.

Sergey (Bruno) THERE IS ANOTHER SECRET - I WILL PUT A NIVSKAYA TRANSFER WITH A CENTER DIFFERENTIAL UNDER THE TRAILER AND THERE WILL BE ALL-WHEEL DRIVE.

Nikolay (Baladhi)  soon the new field will be improved, maybe it will be better

Tags: How to make a walk-behind tractor from a VAZ bridge

Rear axle VAZ 2101 shortened for walk-behind tractor

Our assistant MOTOBLOC | Topic author: Nikolay

Dnepr cargo motorcycle

Sergey (Kazuno)  Dnepr highway motorcycle. Without forced cooling with a load through fields and forests. The engine will suffer. In the summer heat, it instantly heats up and turns the liners.

Nikolay (Cramer)  3 years work Dnieper excellent temperature

Sanya (Chaviv)  I want to make one for myself, only from “Ural”

Sanya (Chaviv)  Tell me, what is the bridge made of?

Vladimir (Annamae)  I think from the classics.

Vladimir (Annamae)  Why are you removing comments?

Sanya (Chaviv)  Can a Muscovite be supplied with his own risors?

Evgeniy (Amadee) About 20 years ago, a guy drove around the villages in something like this, repairing sewing machines.

Evgeniy (Amadee)  The duralumin van was larger than the heel.

Nikolay (Cramer)  vase 2101 bridge

Sanya (Chaviv)  What kind of springs?

Nikolay (Cramer)  Muscovite

Sanya (Chaviv)  What about the brakes? On liquid?

Nicholas (Cramer)  cable

Homemade walk-behind tractor based on the Minsk motorcycle...

Apr 24, 2014 - A walk-behind tractor based on Minsk and a VAZ bridge... nothing shakes or dangles, well, what do you think you will do from your bridge?)).

Rear axle VAZ 2101 shortened for walk-behind tractor...

DIMENSIONS for 70 cm track, shorten the bridge of the vases - Duration: 2:18. Alexander Buek 617 views. 2:18. How to make a Trailer for a Motoblock...

Read also