There can be many types of finishing, it could be ceramic tiles, paint, plaster, wallpaper. However, if the choice fell on Italian or German vinyl wallpapers, then there is no doubt that you made the right choice - this is definitely a good wallpaper finishing material.

We will talk about how to glue wallpaper a little lower, but now we should dwell on the pros and cons of the material.

The advantages are as follows:

1. Availability of leveling properties.
2. Ease of operation and installation.
3. No harm to humans and animals.
4. Long service life.
5. Beautiful appearance.

It is impossible not to mention the scope for designer imagination, since vinyl wallpapers provide the opportunity to get creative when decorating walls. If you choose wallpaper for painting, you may have to paint it again and again, up to 20 times.

You can safely paint the meter ones yourself 3 times. In addition to the fact that the material does not cause harm and is environmentally friendly, it also has an excellent texture and can decorate any room.

Flat vinyl is denser, while foam vinyl is airier, and both options are chic for the home. Wallpapering is possible in any room. If you plan to hang wallpaper in the kitchen, then it is better to choose flat textiles rather than foamed ones; such vinyl is easier to wash. The material has no disadvantages, the only relative disadvantage is the high cost of the wallpaper.

Even more information about various types Wallpaper you can read in the following article:

Self-repair: how to do it right glue vinylnon-woven base

The first step is correct marking. Only if the markings are smooth and accurate, the sticker meter wallpaper will go perfectly. This stage cannot be ignored, especially for material with patterns and patterns; it is important that it matches. Any, even minor, deviations will be immediately visible, especially at the junctions with slopes and openings. Using building level should draw a straight vertical line.

Before drawing, you need to step back from the corner a distance that is equal to the width of the wallpaper, and subtract 20 cm. This is done to overlap the adjacent wall.

It is important to remember that the joint is not made in the corner. Then you need to work on the glue. For vinyl material a special glue has been developed, which is sold in specialized construction stores. Prepare the glue according to the instructions. Usually a pack of powder per 10 liter bucket of water is used. 5 minutes and the glue is ready. Attention! The glue should not be applied to the wallpaper, but to the wall being pasted. For uniform application, a structured roller is used. The next step is the actual wallpapering.

Pasting according to the rules: how to glue hot-stamping vinyl wallpaper

1. The first step is to print the roll, but do not cut it all out. You should lay out the roll on the floor, roll it out, lift it into baguettes and glue it. It is important to glue strictly according to the outlined markings; it must be aligned along the line.
2. As soon as the canvas is pasted, it must be leveled with a special spatula. This will allow excess glue to be expelled, and the air and wallpaper will not bubble in the future. When working with a spatula, you need to move from the middle to the edges. There is no need to be afraid of stretching the fabric; the non-woven base hardly stretches.
3. A very important step is the connection with the baguette, the upper ceiling plinth. For a good connection, use a spatula to press the wallpaper with its sharp side into the corner between the wall and the ceiling plinth. If there is excess fabric, then you need to carefully form a bend and use a stationery knife and a metal ruler to cut off all excess. The knife must be very sharp, otherwise it will not be possible to cut the wet fabric efficiently. You should also cut at the bottom; here you don’t have to be afraid to cut unevenly, since the wallpaper at the bottom is usually covered with a floor plinth.

All other panels need to be glued in exactly the same way. There is nothing complicated, the main thing is to make the joints correctly. After pasting, you can go over all the walls with a roller, this will even out the wallpaper well. This is what the whole gluing process looks like.

Choice of material: what glue to use for vinyl wallpaper on non-woven backing

Having decided to stick vinyl wallpaper on non-woven fabric, you can be sure of the right choice, since it is a beautiful, high-quality finishing material. Foam material is a modern innovation. Thanks to him you can achieve perfect renovation, even a beginner in this matter can hang wallpaper. can be on paper or non-woven basis.

Paper vinyl sheets should be glued according to the same rules as any others. There are a number of requirements for a non-woven base.

The repairman must know what kind of glue is needed for gluing. If you don't pick the right glue, That good result It won’t work, there will be a defect, since the technology is broken. The pack of glue should indicate that the composition is suitable specifically for non-woven vinyl; it is important to look at the markings on the roll.

Rules for gluing

1. Apply glue only to the surface of the wall and in the corners.
2. The walls must be coated very carefully; there should not be a single dry island.
3. The glue must be diluted to normal thickness; it should not be very liquid.

If you choose the right glue, then gluing will be quick and easy, and the repair will delight you for many years, the wallpaper will not come off, will not swell, or peel off. Yes, if after the sticker the walls become visible, you shouldn’t be afraid of it, because as soon as the glue dries, this effect will disappear. The wallpaper dries quickly, literally 12 hours.

The basis of high-quality repairs is Italian vinyl wallpaper on a non-woven backing.

Finishing materials vinyl on non-woven fabric will help speed up the process of pasting walls. The advantage of this finishing material is that during operation it does not stretch, shrink or deform. Non-woven wallpaper made in Italy is stronger and more durable. Italian finishing materials are familiar to the whole world and many production foremen repair work prefer to choose this particular material.

Reviews from professional repairmen are extremely positive, they noted that this type wallpaper:

• Has hygienic characteristics;
• Safe for humans and animals;
• Has attractiveness;
• Easy to apply and lasts for many years.

With sticker Italian wallpaper Anyone can do it, the main thing is to follow the rules, glue in even stripes, make sure when cutting that the pattern matches, use good glue, take your time. An important advantage of such canvases is that the wallpaper, if the wallpaper is pasted crookedly, can be easily removed and moved.

Modern vinyl wallpaper on non-woven backing Germany - what is it

Wallpaper from German manufacturers, as well as Italian models, are among the best. Designers are very fond of this finishing material, since there are a lot of options on the market with different textures, patterns, different color palette. Wallpaper imitating animal fur and photo wallpaper with Methylane stickers are considered fashionable today.

What is the composition of non-woven wallpaper, what properties do they have, you will learn by reading our following material:

German vinyl wallpaper can be installed in rooms of a wide variety of styles, such as:

• Classic;
• Baroque;
• Minimalism;
• Vanguard;
• High tech.

The material is of high quality, it is beautiful and durable. Wallpaper is easy to work with, so when choosing it for repair, you can rest assured that you will receive perfect result, which will please both the master and his family.

High-quality vinyl wallpaper on non-woven backing: characteristics

Vinyl wallpaper for walls is, as already mentioned, high-quality, durable, beautiful materials, which are not harmful to a living organism. How is the front layer of such finishing material used? polymer material, which gives the wallpaper excellent performance characteristics.

So, they differ from other types of wallpaper in the following characteristics:

• Resistant to fading;
• Protection against fungus and mold;
• Wear resistance;
• Water resistance;
• Easy to care for.

This current view The finishing material has a special porous structure, which makes it better than others. The canvas breathes, but does not allow liquid to pass through. It is practical and durable. Connoisseurs of reliability and beauty have long chosen this type of wallpaper, knowing its difference from other types.

How to properly paint non-woven vinyl wallpaper

Painting must be neat. If you choose vinyl for painting, then the master will have more than one option for using it. Of course, the master decides how many layers to paint, but experts recommend making a single-color coating in 2 layers. You can apply paint from the wrong side, but it will not be easy for a beginner to cope with this method; it is better not to experiment. Before painting, it is important to choose the right paint and tools.

A good paint should have the following characteristics:

• UV resistance;
• Quick drying;
• Purity;
• Covering power of the applied layer.

The paint can be acrylic, latex, polyvinyl acetate. good paint A specialist will help you choose, and even a beginner can handle painting in one tone. Painted vinyl non-woven wallpaper will last for many years.

Home gluing of non-woven vinyl wallpaper on the ceiling

Wallpaper on non-woven fabric should be installed on the ceiling area using the same technology as on the walls. It is important to adjust the wallpaper to ceiling plinth and carry out high-quality pruning. You need to stick along the direction lines.

In order to make lines you need to use:

• Lace;
• A brush.

Also, when pasting, you need to prepare a platform. This will allow you to glue the wallpaper along its entire length. The most effective solution there will be a device scaffolding. Each strip is pasted one by one and the scaffolding is moved. It is better to glue it to the ceiling together. The ceiling should be smeared as usual, and the wallpaper should be folded like an accordion, this will make it more convenient to work.

The hole for the ceiling rosette is made by piercing the wallpaper. It is very important to turn off the power supply to the panel.

How to glue vinyl wallpaper on non-woven backing (video)

So, when choosing wallpaper, you need to consider its harmfulness and environmental friendliness. Choose a style and think over the overall design. If you do everything according to the rules and are well prepared, the repair will go without any problems.

Kirill Sysoev

Calloused hands never get bored!

Content

Hundreds of types are sold in stores beautiful wallpaper. Not very popular paper options, which are difficult to use. Buyers prefer a relief pattern with a dense base. At the same time, when acquiring such a texture, you need to know how to glue vinyl wallpaper on a non-woven backing. There are several tricks that help you change the design of a room easily and quickly; it is important to follow a few rules, and then everything will work out, even for beginners.

Features of gluing vinyl wallpaper on non-woven backing

What is the peculiarity of modern wallpaper, how long does it take vinyl wallpaper on non-woven backing to dry? They differ in their density, they are created from several layers, visually they seem thicker than paper ones. This characteristic allows the fabric not to stretch even after glue gets on the surface. Once applied to the wall, they do not shrink and the pattern is not deformed. Some wallpapers can be washed; their coating is not afraid of moisture. The weight of each roll is light, and they stick more firmly to the walls.

When choosing wallpaper in a catalog or in a store, you need to understand that hot-stamped vinyl on a non-woven backing often requires adjustment. For example, photo wallpaper requires precise joining in order for the design to be harmonious. Wallpaper with embossing is purchased with a margin of 10-15%, because trimmings remain when creating a single ornament. When purchasing, it is recommended to make sure that all rolls have the same pattern and there is no difference in color. It is better to choose wallpaper from one batch.

Is it possible to paint vinyl wallpaper on non-woven backing? Some types of these coatings are specially created for painting. They are dense, not afraid of water and are not deformed by paint. Paint can be applied up to 6 times, but they show through a little, the bottom layer should not be darker when painting to get the desired result. Only the coating for interior work so as not to cause harm to those living in the premises.

Preparing the walls

How to properly glue vinyl wallpaper? The process begins by preparing the walls. It is important to remove the previous coating and level the surface. How larger picture, the better they will hide the unevenness of the walls, so do perfect angles not necessary. If you are planning a monochromatic coating or a small pattern, you should pay more attention to the condition of the walls.

How to glue vinyl wallpaper on a non-woven backing so that everything turns out perfect? It must be remembered that wallpaper is translucent. Below them you will see the drawings that are on the surface to be pasted. If the walls different color, applied thin layer plaster. If the walls are dark, it is also recommended to apply an additional lightening layer. This kind of preparation will help you avoid surprises.

Step-by-step technique for doing the job

Wallpaper plan:

• Initially, the height of the wall is measured. The strips are cut with an allowance of 5-7 cm. The strips must fit perfectly together, so it is easier to cut them from 2 different rolls one by one. It is necessary to prepare at least 4 vertical stripes before gluing. Sometimes it is appropriate to cut off all the required strips at once.
• How to properly glue vinyl wallpaper on non-woven backing? It is important to start from the window. The first strip is glued exactly vertically; if there is even a slight displacement, its angle will increase in the future, so this should be avoided. To make it perfect, draw a vertical line to help align the starting strip.

• The glue is applied to the wall surface in an even layer. Every centimeter is coated, the area being slightly larger than the size of the strip. It is recommended to apply the glue with a roller or brush in a thin layer. Additionally, glue is placed on the edges of the wallpaper to make the joints more even. There is no need to add a fixing compound to the entire canvas. After this, the first strip is applied to the wall, the reference point is the previously drawn vertical line.
• When wallpaper is on the wall, you need to smooth the surface with a roller or soft rag. There should be no bubbles, compactions or unevenness. In this case, it is possible to easily adjust the design so that it looks perfect. Sometimes glue appears at the joints; it is removed with a damp sponge. It is prohibited to smear it on the surface of the wallpaper.

• The canvases are glued end-to-end without overlap. Excess parts formed at the bottom or top are cut off. If there are sockets on the wall, it is recommended to remove them, turn off the electricity, stick the cloth, and then carefully cut a hole for the wires and return the structure to its place. All manipulations must be done carefully. And in last resort seal the space by the window. Above and below the window opening, small pieces of wallpaper are fixed, which are cut out from the remains.

Video tutorials on gluing vinyl wallpaper on non-woven backing

There are many nuances in wallpapering. For example, what glue should I use to glue non-woven vinyl wallpaper, how to dilute it and for how long to use it? Questions also arise about decorating difficult areas: corners, the space behind the radiator, above windows or doors. These features can be easily understood with the help of a video that shows in detail how such problems are solved.

Step by step lesson for beginners

How to measure the height of the wall, foam the glue, quickly cut the canvases and place them on the wall? This video will tell you about little tricks that will reduce the time it takes to create a new interior and allow you to do renovations in a matter of hours, even alone. Working with non-woven wallpaper is shown in as much detail as possible, and reviews of this lesson say that it has helped dozens of people cope with repairs without outside help.

How to properly cover walls

The walls in houses and apartments differ in materials, evenness and color. But the principle of wallpapering is the same for everyone. Detailed lesson on decorating a room modern wallpaper shows how to change the walls in a room in a short time. Using the example of two masters, it is clear not only how to choose wallpaper and place the first strip, but also how to make perfect joints, carefully fit sockets and adjust the design.

How to glue wallpaper to the ceiling

Pasting the ceiling requires special skill. The markings are not done like on the walls, and it is more difficult to align the pattern. The intricacies of this process are easy to master and are covered in detail in the video. Using the tips, you will be able to create flat surface even over your head. You just need to comply simple rules, do everything step by step and take your time.

How to glue corners

Corners in a room are the most difficult area to glue. Walls are rarely strictly perpendicular, so in this area you have to adjust the design, coming up with many tricks. An overlap is allowed for alignment, but to make it perfect, watch the video where the detailed instructions. A step-by-step demonstration will help you avoid mistakes.

Found an error in the text? Select it, press Ctrl + Enter and we will fix everything!

Vinyl wallpaper since its appearance on construction market, immediately gained well-deserved popularity. And this is no coincidence, because pass them by unique qualities impossible. What has earned the demand for this finishing material made on the basis of polyvinyl chloride, or rather, polyvinyl chloride mass applied to a paper or non-woven base? One thing is clear, this is undoubtedly the material of a generation and today there is no question of whether to use wallpaper of this class, but on what design vinyl wallpaper stop your choice.

The undoubted advantages of vinyl wallpaper with a non-woven base

This material has excellent characteristics, both technical and operational:

1. They have a very dense structure, which facilitates their use on surfaces even with some minor defects without damaging their appearance;
2. Wallpaper of this type has a minimal shrinkage coefficient;
3. It is very easy to stick such wallpaper; besides, this non-woven-based finishing material adheres perfectly to almost any surface - plaster, putty, wood, concrete and any other material. You can glue such wallpaper on both vertical and horizontal surfaces;
4. Wallpaper of this class is divided according to structure, thanks to which you can create a different interior inside the apartment.
5. Today, manufacturers have developed vinyl wallpapers for repeated painting.

As you can see, the product has an impressive list of advantages, so on the ceiling and wall surfaces of most apartments and office premises this unique material has received a permanent and well-deserved registration.

Flaws

One of the main and very significant drawbacks is the airtightness of this type of wallpaper. High density material made on the basis of polyvinyl chloride prevents normal air exchange. However, it should be noted that today manufacturers have taken this flaw into account and analogues of this wallpaper material made from foamed raw materials have appeared on the construction market, in which high air conductivity is observed, while all others positive characteristics not changed.

Wallpaper gluing technology

Now let's talk about how to glue vinyl wallpaper. Vinyl wallpaper is glued to the surface using a special glue designed specifically for this type of wallpaper. However, this does not mean that it is enough to purchase required quantity wallpaper and glue and can be dressed up in beautiful clothes walls and ceiling. Because, as with any other finishing material, you first need to properly prepare the surface of the wall or ceiling. And this stage of repair also requires sufficient quantity labor costs and time.

This process begins with removing the previous finishing material from the surface of the wall (or ceiling), regardless of what we are dealing with - old wallpaper, paint, ceramic tiles or simple whitewashing, that is, the surface should be completely cleaned and all open and invisible defects should be eliminated.

Cracks, chips, irregularities, pits and other defects should be eliminated and puttied, then the surface should be thoroughly primed and wait until completely dry.

The next step in this process is to apply a thin layer of putty to the entire surface and perform the leveling process. We have already mentioned above that vinyl wallpaper on a non-woven basis does not require ideal evenness or smoothness of the surface; their structure will disguise minor defects. After giving the putty the required time to dry, the wall should be primed.

Now it’s the turn of the wallpaper itself - you should prepare a strip of material of the required length, adding about ten centimeters to the actual length for various unforeseen circumstances, and treat their surface on the wall side with glue.

Because standard width a roll of vinyl wallpaper on a non-woven basis is one meter, then perform the calculations general need wallpaper strips for pasting a room is not difficult. Therefore, it is advisable to cut all the material at once, so as not to be distracted from the gluing process.

Then in one of the corners of the room you should draw a vertical line, which a level or plumb line will help you with, and it is better to draw the line itself with a pencil. Thus, we will set a kind of reference line, which will become the starting line in the process of wallpapering. In this place, vertically to the width of the wallpaper strip and with a slight margin, using a paint brush or roller, apply glue to the surface. Glue mixture can be applied in a fairly thick layer without thinking about saving it.

We glue the first strip exactly along the vertical mark made. And if suddenly something turns out wrong, there’s nothing to worry about, the strip can be removed and re-glued. This is also one of the undoubted advantages of vinyl wallpaper; they can be re-glued many times without damaging the material (but, of course, not indefinitely). Leveling is best done with a rubber roller and spatula. High-quality leveling will occur if you perform this process from top to bottom and at the same time from the center of the strip to the sides, squeezing out the remaining air from under the material. Having finished with the first canvas, move on to the next, exactly repeating the process of gluing the first strip, and repeat this with all the other canvases.

Vinyl wallpaper should only be glued end-to-end.

The real challenge awaits you in the corners of the room. Here wallpaper of this class should be glued overlapping. In order for the convergence of the material in this complex part of the room to be satisfactory, the wallpaper should be trimmed, leaving an allowance of five to ten centimeters on each strip. First, you need to paste the canvas, which is a continuation of the wallpaper row with a transition to another wall (there is no need to peck the strip on the other wall).

We do the same with the canvas of the second wall - we also extend it by the indicated 5-10 centimeters onto the previous canvas, and then with a sharp knife we ​​cut both canvases vertically right along the corner from top to bottom. Remove excess pieces. Thus, we made the joint directly in the corner of the room. When gluing the corner part of the room, all of the listed work should be done slowly and carefully, because this is a very responsible job. Inaccuracy or negligence can undo all the good work previously done.

It is best to apply glue on the corners with a brush.

So, we have looked at how to properly install wallpaper on a non-woven basis, and we can draw one indisputable conclusion - there is no particular difficulty in this process. As in any other stage of repair or gluing regular wallpaper, it is necessary to carefully and thoughtfully paste the wall surfaces in accordance with the recommendations given. And the result for your patience and desire will be unusually spectacular wall surfaces.

Anyone who does renovations with my own hands, wonders how to glue non-woven wallpaper, and not in vain. The procedure has a number of characteristic features, and if they are not taken into account, the quality of work will suffer. The recommendations given below will help you avoid any marriage. The wallpaper will not fall off, will not swell, will be glued evenly and will retain its attractive appearance for many years.

Rules for gluing non-woven wallpaper yourself

The pasting technique involves the use of generally accepted norms and rules. In addition, you need to take into account the characteristics of non-woven fabrics finishing materials. They are wider than paper ones and are heavier. All you need to know so that the interlining does not swell and the pattern is preserved is:

• Before gluing the walls you need to putty (if the panels are uneven) and prime.
• The direction of the pattern is indicated on the packaging using special symbols.
• Adjustment of the pattern along the edges is carried out in accordance with the instructions (straight - all strips are glued in one direction; reverse - in the opposite direction).
• The non-woven fragments are pressed against the wall from top to bottom, smoothed with a dry cloth, and the joints are rolled with a special rubber roller.
• Glue needs to be applied to the wall. Non-woven fabric allows you not to apply it on reverse side canvas bases.
• The technology involves gluing strips without seams (joint to joint, without overlap).

The temperature in the building must be constant during drying. Heavy weight non-woven finishing materials require that the glue has the appropriate thickness and viscosity. Wallpaper does not wrinkle if, after gluing, the surface is smoothed using rollers or clean rags.

Which wallpaper glue is best to choose for non-woven wallpaper?

Paper is used as the basis for wallpaper production, which allows the use of starch-containing compositions. You can glue using PVA glue or specialized mixtures. If they contain polymer components, then such wallpaper can be glued to drywall or cork without puttying. Mixtures are now being sold that include antibacterial additives that prevent mold and mildew from appearing.

This problem is solved with a primer. Before gluing, you need to take into account the thickness, size and weight of the strips. If we're talking about For massive non-woven wallpaper, a thick (viscous) solution is used when gluing. The lungs can be glued to liquid. If the wall surface has unputtyed shells, glue that has increased thickness is used. The preparation recipe is indicated in the instructions for use.

What tools will you need?

You should prepare in advance. You will need equipment and tools. Before you start working with non-woven materials, you need to think about what kind of glue to use and what you will need for this. The process cannot complete successfully without:

• wide brushes or rollers for applying adhesive;
• wallpaper knives and a wide spatula for cutting the ends of the strips;
• special equipment (electronic levels, plumb lines or levels);
• containers for preparing glue;
• clean dry rags for smoothing the surface of the wallpaper;
• stationery scissors;
• narrow rubber rollers for rolling seams (joints);
• pencils or ballpoint pens for marking.

All of the above must be available. The list does not indicate the tools necessary for the preparatory work.

Proper preparation for gluing

General requirements state that before gluing non-woven wallpaper, you must:

1. Wash the floor, or better yet, lay cellophane on it. This will save time on cleaning.
2. All electrical wiring outputs are isolated.
3. By removing socket covers and switches, the room is de-energized.
4. If natural light there is not enough in the room, the “glasses” with connectors for sockets and switches are sealed masking tape, which is then deleted.

All necessary equipment must be in good working order, clean, and preferably new.

How to dilute glue correctly?

It is best to do the preparation immediately before gluing non-woven wallpaper. Strips of the required length are cut in advance. The dry granular mixture is poured into a dry container. Then it is filled with the required amount of water. In this case, you need to continuously stir the resulting mass until the granules are completely dissolved, monitoring the consistency.

IMPORTANT! Recipe indicated on the package wallpaper glue, is designed for the entire pack, and diluting the glue in advance is impractical. Over time it thickens. Optimal quantity- 4-5 lanes.

Surface preparation

Non-woven wallpaper can be glued to:

• concrete panels;
• plastered brick walls;
• plywood or OSB;
• drywall or other prepared surface.

Laminated chipboard surfaces are not suitable, since such a surface does not absorb glue, and there will not be sufficient adhesion to non-woven elements. It is important to remove remnants of the previous coating:

• paints;
• decorative plaster;
• dry plaster;
• lime whitewash;
• old wallpaper.

The surface is cleaned of dirt, oily stains and dust, leveled (plastered) and primed. Only after this can you start gluing non-woven wallpaper.

Algorithm for gluing on walls with your own hands

First, the wall is coated with glue. The width of the treated surface is greater than the width of the roll. Lubricate with a special soft roller or a wide thick brush. When preparing the stripes, take into account the need to adjust the pattern. Non-woven wallpaper needs to be glued joint to joint.

Stage 1: diagram and marking of walls

The width of the roll is measured from the window, and a level or plumb line is drawn vertical stripe. This is a guideline so that the fragments and joints are even. By marking the wall along its entire length, you can determine the required number of solid strips, which should be cut in advance.

Stage 2: preparing wallpaper

If non-woven wallpaper is glued without matching the pattern, the fragments are cut with a small margin in length (5-7 cm more than the ceiling height). When it is necessary to adjust the pattern, the margin is made larger by the amount indicated on the packaging of non-woven wallpaper opposite the corresponding symbol.

Stage 3: gluing

The pasting process begins from the window. When applying fragments, you must ensure that they are vertical. To do this, markings are applied to the wall.

When gluing non-woven wallpaper, only the wall is covered with glue. If the canvases are heavy (with vinyl covering) it may be necessary to apply glue to both the wall and the wallpaper.

Rolling with a roller or smoothing with a rag, press the middle of the strip along the entire length, having previously unrolled the wallpaper.

Remaining air and excess glue are expelled from the axis to the edges, which are rolled with a narrow special roller for tight adhesion. There should be no overlaps.

Stage 4: final

All protruding parts of the fragment are cut off with a wallpaper knife. To ensure an even cut, apply a wide metal spatula to the cutting line. Below you can leave the wallpaper as is, since after gluing, a plinth is installed that hides the defects.

How to glue in problem areas?

These places include:

• internal and external corners;
• bay windows, arches;
• areas above door and window openings;
• walls behind batteries, etc.

To glue non-woven wallpaper in these places, you need to prepare in advance elements that are suitable in shape and size.

The photo shows a diagram of gluing wallpaper around sockets and switches:

The photo shows a diagram of wallpapering behind the radiator:

Features of gluing meter wallpaper

There are several factors characteristic of non-woven wallpaper one meter wide:

• The glue is applied only to the wall.
• If mistakes are made, you can remove the fresh canvas and re-glue it.
• It is difficult to do the work alone.
• Non-woven fabric allows you to adjust joints using the smoothing method.

Step-by-step guide to covering a ceiling

The process has a number of features. The strips are laid across the width of the room from window to door. The difficulty may be caused by the place where the chandelier is attached, but this can also be solved.

Video instruction

For clarity, before gluing non-woven wallpaper, it is recommended to watch the video. Where everyone is told technological nuances process.

How long does non-woven wallpaper take to dry?

It all depends on the temperature in the room. The higher it is, the longer it will take until it dries completely. Usually it is 6-10 hours. At this time, there should be no drafts in the room.

The pasting procedure is simple and can be done independently, without the involvement of a professional construction crew. Non-woven wallpaper is ready for painting, which is a definite plus. The only thing you need for quality repairs– accuracy and the above instructions.

Non-woven wallpaper can be of two types: with a pattern and for painting. Such products can easily disguise wall imperfections that remain after repair work. Therefore, non-woven wallpaper is used in great demand. You don't need any special skills to glue them.

You should know that the non-woven base can slide along the wall, so it will be possible to paste it without outside help. If you choose wallpaper for painting, you can easily change the color scheme of the interior. In this case, the room will always seem fresh.

Today, large-width wallpaper is used quite rarely, but you can find it on sale a large number of of this material. Such wallpapers have some advantages:

• Large-width wallpaper can significantly simplify the gluing process;
• in this case there will be a minimum number of seams that spoil the appearance of the room.

Necessary preparatory work

In order for the gluing to be done efficiently, you will need to perform some preparatory work. First of all, it is necessary to calculate with maximum accuracy the number of rolls of material that will be needed to cover the room. To do this, you will need to measure the width and height of the room on each side separately. In the process of counting required quantity rolls will need to be added to the length of the canvas a few centimeters on each side in reserve. For clarity, you can draw a diagram on paper.

When choosing non-woven wallpaper, you will need to pay attention to the batch number, which is indicated on the packaging. It should be the same on all rolls. If there is a drawing, it must also be identical.

In order for the wallpaper to fit correctly on the wall, you will need to prepare the room. The walls must be carefully leveled. This is especially important to do if you plan to stick wide wallpaper, which will not fit correctly on uneven walls. If the surface is not leveled, this will further affect the quality of the joints.

Sockets and switches will need to be removed. The wires will need to be insulated so that the adhesive mixture does not get inside the boxes. All walls will need to be thoroughly treated with a primer mixture and then dried.

To do this you will need to prepare the following items:

1. Video clip. Will be used for edge processing.
2. Polyethylene film.
3. Short bristled brush.
4. Plastic spatula.
5. Container for adhesive mixture.
6. Roller.
7. Roulette.
8. A simple pencil.
9. Level.
10. Non-woven wallpaper adhesive mixture.

Return to contents

DIY technology for gluing non-woven wallpaper

First of all, you will need to mark the walls. Non-woven wallpaper has an excellent edge and is glued end-to-end. The marking should start from the corner of the room. In these places, the canvas will be glued overlapping so that they can be processed correctly. If you plan to glue material 1.06 m wide, then you will need to set aside 1 m in all directions from the corner.

By using a plumb line or building level and a simple pencil You will need to mark a vertical line to the height of the builder. Using a tape measure, you will need to mark 1.06 m from the drawn line. Thus, you will need to outline all the walls.

If there is no pattern, you will need to use a tape measure to measure the height of the room in the place where the piece of wallpaper will be pasted, and you will need to add another 10 cm. The roll is folded onto the rolled out part so that the edges coincide. In this case, you will get an even fold. You will need to run your hand along the fold and then cut it with a construction knife. In this case, you can use a new stationery knife. In this way, wallpaper is prepared for the entire room.

The canvas will need to be rolled into loose rolls so that front side was inside. Thanks to the non-woven base, there should be no problems in this case.

Next, you will need to dilute the adhesive mixture according to the instructions. It is allowed to use only adhesive solution for non-woven wallpaper. Water is poured into the prepared container, after which the glue is poured out in a thin stream. During the preparation of the mixture, it must be constantly stirred to prevent the formation of lumps that could prevent the wallpaper from being properly applied. The adhesive solution needs to sit for a while to swell. You can install a plastic mesh in the container to remove excess glue.

The roller will need to be immersed in a container with the solution, and then passed over the mesh. Next, you need to spread glue on the wall to stick one sheet. You need to start gluing the panel from the top.

You need to grab the extreme part of the canvas, and then attach it to the wall. The roll slowly goes down; in the process you need to smooth the wallpaper from the middle to the edges with a brush. In this case, you can also use a plastic spatula, but all actions must be performed carefully, as the wallpaper may be damaged.

Non-woven wallpaper should be glued so that it fits tightly to the wall. Bubbles and folds are not allowed.

After gluing the two canvases with a roller, you need to roll the seams of the material. The piece of wallpaper that remains below will need to be carefully cut off. This should be done after the wallpaper has dried. It is necessary to calculate everything so that the baseboard installed later can cover the lower part of the wallpaper. A border of the required thickness can be installed at the top of the wall.

Return to contents

How to glue non-woven wallpaper on corners

The first step is to prepare the corner of the room. This must be done while the walls are being putty. The corners are equipped with plastic fixtures that are attached to the walls with putty. The entire product must be completely dry, only then can you begin gluing non-woven wallpaper. In the process of gluing the corner, the wall and the plastic corner will need to be thoroughly coated with the adhesive mixture.

The panels will be placed overlapping; it is not recommended to glue the whole panel onto a corner. In most cases, the corners in the rooms are not ideal, and as a result, defects may occur: the corners of the material will wrinkle, the strip will become skewed. To eliminate this, you need to glue the corners correctly.

The canvas should be glued in such a way that there is a slight overlap on the wall located nearby.

The next strip is glued on the other wall, it is glued to the corner with a slight overlap. Next, this “tail” is cut off using construction knife, you need to orient yourself along the vertical angle.

As a result, up to 2 cm of panel from the adjacent wall will be glued under this canvas, and the first canvas will rest against the edge of the corner.