• This equipment, despite its quiet operating mode, is practically not inferior in technical parameters to bulky and noisy industrial installations designed for high loads and long-term use.
• The performance of the offered compressors, depending on the model, ranges from 60 to 650 liters of air per minute. For comparison: the same parameter of a conventional piston device reaches only 520 l per minute.
• The pressure created by such a compressor varies from 3 to 13 atm. In this case, the power is from 0.75 to 4 kW, and the required mains voltage is 220 or 380 V.
• The assortment includes various models compressor equipment with a low noise threshold, manufactured at foreign factories under the brands Comprag, Remeza, etc.

To buy a quiet one air compressor at EnergoProf, contact the company's employees. Phone numbers are listed in the header of the page and in the “Contacts” section. In assortment a large number of low noise compressors of different power. Please study our offer carefully before purchasing.

Every aquarist knows a small but irreplaceable aquarium device that, under slight pressure, pumps air into the thickness of the aquarium water. Air bubbles rising to the surface create a slight seething, oxygen from the air actively saturates your pond. This burbulator is called a compressor or aerator. Aer - Latin for air.

There are several types of compressors for aquariums. The most common and long known are piston and membrane ones. Not long ago, piezo compressors of the aPUMP type appeared on the market. In addition, ordinary aquarium pumps or airlift filters can solve the problem of saturating water with oxygen.
Despite all the variety, the main drawback of all types of aquarium compressors is the noise they make. If your aquarium is located in a room where someone sleeps, the quiet operation of the compressor is one of its most important qualities. Unfortunately, there are no silent compressors - their operating principle is based on vibration.
Diaphragm compressors are considered one of the noisiest compressors. However, a membrane compressor will save you some energy costs, it has a long service life, and it almost never breaks down. Plus it's more efficient. Therefore, such an aerator can be connected to several aquariums at once.

The generally recognized leader among silent compressors are piston compressors. IN Lately Piezo compressors compete with piston aerators in terms of noise emitted. However, they also have a drawback - they are low-power and cannot be placed in containers larger than 200 liters.

When the aquarium tank is large enough - from 150 liters or more, some aquarists install two or more aerators in it. In this case, you can choose compressors different principles work - piston or piezo and membrane. The first can be turned on at night, the second - during the day.

There is one more little trick. To dampen vibration that creates noise, you can place a flat rubber or foam mat under the compressor, for example, from a computer mouse or a fragment of an old yoga mat. Sometimes aquarists take the compressor to another room and connect it to the aquarium using a long tube - an air duct. This method is not considered effective. Can you imagine how powerful a compressor must be to “push” air over a long distance?

Another device, effectively decisive issue saturating the water in the aquarium with oxygen is an aerator like the H2Show BubbleMaker - this device is installed inside the aquarium and works on the Venturi principle by “sucking” air through a tube, creating a powerful vortex of small bubbles using a rotor, without the need for a compressor.

The aquarium pump, which is the basis of all modern internal filters for aquariums, is also often used to saturate the water with oxygen. An additional function is provided by a small device that allows you to “suck” air from the surface and carry it along with the movement of water. In addition, the pump helps to coordinate the flow of aerated, oxygen-rich water, which is also the main element of biological filtration. If you have large aquarium, from 150 liters or more, it is advisable to purchase a pump that will help ensure good water circulation, thereby promoting the well-being of all inhabitants of the aquarium. The tube for sucking air from the surface also makes a specific noise - a slight whistle, which can irritate people with light sleepers. However, we have learned to solve this problem too. In modern pumps, the tubes are equipped with a small plug. By changing the position of the plug, you can get rid of the intrusive noise, or at least significantly reduce it.
The latest in a series of devices that enrich water with oxygen are airlift filters. Actually, this is a design that gives additional capabilities to any of the above compressors. The air is supplied by an aerator to a device equipped with porous materials (sponges, zeolites, etc.). Air bubbles escaping to the surface create a draft that drags the aquarium water along with it into the filter elements. Airlift filters make a constant murmur. Based on experience, almost no one has been able to reduce the noise of airlift filters.

If you are not satisfied with the quality of branded compressors for an aquarium, you can make it yourself. However, such a device will only work well if you have the skills to create such mechanisms. Homemade compressors can cause a short circuit in the water, which is very dangerous to life. Waterproofing in this case is extremely required part aerator. Well, the design of homemade devices, as a rule, leaves much to be desired.

Obviously, each of us wants to choose good, high-quality equipment that would meet our needs and requirements. This article will focus on aquarium compressors. The fundamental requirement of any aquarist for a compressor is its silent operation. Based on our own experience and collected information, we decided to make the TOP best compressors for an aquarium.The purpose of this rating is to publish the opinion of aquarists who have tested various aquarium compressors in practice.. We will evaluate the noise of the device itself; the noise from the bubbles does not count.

Compressor Schego Optimal -

aPump compressor -

Compressor Prime -

Aerator H2Show (Hydor) Bubble maker -

Ehmein compressor -

So, here is our topic.

5th place: Eheim 100/200/400

Description: modern device, which will allow you to saturate the aquarium water with vital oxygen. Suitable for both marine and freshwater aquariums. Due to its compact size, this compressor does not take up much space, and its convenient mounting form will allow you to install it anywhere. Magnitude air flow simply adjusted via a switch located on the front panel of the device. It works almost silently.

4th place: Schego Optimal

Description: The Schego Optimal compressor is one of the most popular among aquarists. Suitable for aquariums with a volume of 50 to 300 liters, productivity up to 250 l/h at a power of 5 W. Airflow can be adjusted. Low vibration makes the compressor operate virtually silent. If desired, and if you have a splitter, you can connect it to several aquariums at once. The device has legs to increase stability and, if necessary, can be hung vertically. The pre-filter is easy to change and the durable membrane ensures a long service life of the aerator.

3rd place: PRIME

Description: piezo compressor PR-4113 for aquariums up to 200 l, is on this moment the smallest and quietest in the world. The air flow pressure created by the PR-4113 compressor allows it to be used for aquariums with a water column height of up to 100 cm.

2nd place: aPump

Compressors from COLLAR are ideal for small aquariums.

1st place: H2Show (Hydor) Bubble maker

H2Show BubbleMaker is an underwater aerator that creates a powerful vortex of small bubbles, without the need for a compressor. The aerator itself is placed inside the aquarium; only the power cable and the air hose are brought out, which can be located inside the aquarium - the main thing is that its tip is out of the water. Of course, if the aquarium has such a device, a compressor will no longer be needed.
Why did we put BubbleMaker in first place? As can be seen from the description, this is not quite a standard compressor, like the ones listed above. Eheim, Prime, Schego, aPump - they are all installed outside the aquarium. BubbleMaker is installed inside the aquarium - under water. Due to this, the water absorbs any noise produced by the device. And since we evaluate specifically the noise of the compressor, BubbleMaker becomes the clear leader. You just can't hear him.

Please note that the BubbleMaker has an aeration tube from which a bubbling sound may be heard. However, with the help of a cap at the tube outlet, this noise can be leveled out, and the bubbles will become even more finely dispersed, which is very good. By the way, some aquarists use this property of BubbleMaker to supply CO2; the result is a reactor that produces bubble dust, which is very important when supplying carbon dioxide.

The only caveat of this device- the manufacturer’s recommended working depth of immersion is no more than 45 cm, although in practice there are examples successful work of this device and when installed at a depth of 55 cm.

This video shows the full power of BubbleMaker

Subscribe to our You Tube channel so you don't miss anything!

This is how our review turned out. Of course, as many people as there are, so many opinions, so study the links given above, discuss, offer your options - this will only benefit the entire aquarium community.

VISIT OUR ONLINE STORE termopro-shop.ru

The silent compressor is an independent, completely self-sufficient air center, created by the best engineers using advanced technologies. Ideal solution for laboratory, industrial or dental applications where clean compressed air, high reliability and efficiency. Thanks to their low noise level and high efficiency, they provide maximum comfort and have a long service life.

Compressors for industrial production

An excellent choice for solving production problems with minimal operating costs. Thanks to the use of advanced technologies, air compressors for industrial production are characterized by a long service life and minimal noise levels.

Silent air compressor for laboratory

This solution is designed for use in laboratories and research centers that use unique equipment. Special attention When developing compressors, reliability and efficiency were taken into account.

Silent compressor for dentistry and medicine

The distinctive advantages of equipment for medical needs are ideal fresh air, no oil contamination and extremely low noise levels. Combined with high reliability and versatility (compressors can be easily connected to any medical equipment), are an ideal solution for surgery and dentistry.

BAMBI compressors

Developed by the best engineers, BAMBI compressors are distinguished by excellent performance, versatility and reliability.

BAMBI compressors BB series

For high-quality car painting, you need an air compressor that will ensure uniform spraying of the paint material. For occasional use, an inexpensive piston compressor with average technical characteristics is quite sufficient. It’s another matter if the compressor has to work in production almost around the clock - without a powerful semi-professional, or even industrial equipment not enough. Of course, any purchase, including a budget one, must be justified by trouble-free operation and a corresponding service life. You say, this doesn’t happen, and we should immediately buy a more expensive compressor? We will disagree with you, since we are already familiar with the rating of the best compressors of different classes and, accordingly, different price categories. All you have to do is choose one of them for your task.

The best household compressors

T.n. Garage compressors are designed for short, small jobs. They cannot be connected to pneumatic equipment with high air flow rates, for example, spray guns with HVLP technology. Painting a car for such a unit is a feasible task, but it takes 2–3 times longer. This is explained by the fact that the duration of its continuous operation usually does not exceed 10–15 minutes, otherwise it quickly overheats and, in the absence of a thermal relay, fails. Hence the conclusion - even a high-quality household compressor must be used carefully and requires competent selection of pneumatic tools based on power indicators.

3 Denzel RS 1/6-180

The most inexpensive and small-sized compressor. Quiet operation
A country:
Average price: 6100 rub.
Rating (2019): 4.2

The Denzel PC 1/6-180 compressor, weighing only 11 kg, is one of the cheapest, most compact and economical. Its peculiarity is the absence of lubrication in the cylinder-piston group, and in order to reduce friction, special anti-friction materials were used in the design. As a result of this solution, the oil does not enter the air and does not mix with the paint and varnish material, so the unit is very convenient to use for painting various surfaces. The output capacity is 180 l/min, and an appropriate spray gun is needed - either an HP or LVPL system.

During operation, the compressor creates a maximum pressure of 8 bar, this indicator can be adjusted, which allows it to be used with a full range of pneumatic tools - from a wrench to an airbrush. What is important for many is that it looks great and works almost silently. Of course, the unit still cannot be called universal, because completely painting the car will take quite a lot of time. The direct drive provided by the design (a rigid connection between the electric motor shaft and the crankshaft of the air blower), although it is the simplest, does not have effective heat removal, so the compressor will have to be stopped every 10 minutes.

2 Fubag Air Master Kit

The best package. Maximum range of work. Easy maintenance
A country: Germany (manufactured in China)
Average price: 9400 rub.
Rating (2019): 4.5

The German company Fubag decided to offer customers not just one compressor, but a whole set of the most popular pneumatic tools needed for car maintenance and home repairs. The official website presents 2 options for sets: 6 and 10 units. The minimum package includes:

• 3 air guns with nozzles - for inflating tires, blowing or washing and for viscous liquids (with a tank);
• 3 tips for inflating balls, bicycle wheels and mattresses;
• flexible 5-meter hose;
• HP spray gun with a 0.5 liter top tank.

As for the compressor itself, it must be said that despite its rather modest dimensions, it pleases with its performance - 222 l/min. at the exit. It is made with high quality, the ergonomics are well thought out: the pressure gauges are perfectly readable, their readings are very accurate, the craters for filling and draining oil are conveniently located. The impression is slightly spoiled by the short power cord and unclear instructions, which include information about several models at once, but given the price and rich set of accessories, these shortcomings can be forgiven.

1 Wester W 006-075 OLC

The best technical characteristics for painting small parts
A country: UK (manufactured in China)
Average price: 7800 rub.
Rating (2019): 4.7

The power, performance and displacement of the receiver in this model are quite modest - only 0.75 kW, 126 l/min. and 6 l respectively. But it fully lives up to expectations, and delivers the stated 8 bar consistently even with a long hose. Users use it with all their might in “garage” matters - local painting and inflation of car wheels, blowing out tools, etc. Someone has even adapted to equip it on the basis of W 006-075 spray booth and the sandblasting service, however, replaced the pre-receiver with a larger one. Thanks to its compact dimensions (WH 22x48x50 cm), the compressor can easily fit even in the smallest workshop, for example, under a workbench, and will not take up extra space.

The manufacturer did not skimp and provided the inexpensive device with all the necessary safety elements: 2 pressure gauges, an oil indicator, safety valve. There are no complaints about the ergonomics or the build quality: the unit is painted well, the gaps are uniform, although it still wouldn’t hurt to tighten some components before the first start; people have been using it for several years without any breakdowns. The working parts are made of cast metal, rubberized legs reduce the level of vibration (by the way, this “baby” is quite noisy), there is a convenient handle for transportation.

The best semi-professional compressors

Semi-professional compressor equipment in most cases is represented by European and domestic producers and has a number of characteristics. They provide a flow rate of over 270 l/min. and pressure 8–12 atmospheres. To support optimal operating mode, the volume of the receiver increases and is approximately 50–100 liters. Non-stop operation of such compressors should not last more than 40 minutes, but this is enough to use them for small service stations and tire shops, car services, and small industries.

3 Quattro Elementi KM 50-380

The best balance between performance and efficiency. Double cylinder group
A country: Italy (made in China)
Average price: 15,300 rub.
Rating (2019): 4.3

For more or less large-scale painting of cars, you need a more powerful compressor, and among relatively inexpensive options we found the most productive - Quattro Elementi KM 50-380. Its markings contain encrypted indicators: 50 l is the volume of the air collector, 380 is an indicator of the input capacity in l/min. The output capacity will naturally be lower and will be approximately 270 l/min. – enough to create a pressure of 8 bar in 1.5 minutes. At the same time, the engine power (2.2 kW) and, accordingly, energy consumption are not much different from the power of less efficient compressors (1.5–2 kW), since the efficiency of this model is higher due to the two-cylinder piston group design.

The manufacturer increased the resource of the unit by installing cast iron cylinders instead of aluminum ones. There is a drain valve on the bottom of the receiver, which allows you to quickly get rid of condensation, and the receiver itself is coated with paint to prevent corrosion. The compressor weighs 40 kg and has a handle and two wheels for transportation. According to reviews, it turns on infrequently, pumps up quickly, which means it will work for a long time. The disadvantages were the inconvenience of changing the oil and the insufficient length of the power cable.

2 Aurora GALE-50

Reliability in operation. Availability of 2 outputs for equipment
A country: Russia (manufactured in China)
Average price: 15,800 rub.
Rating (2019): 4.5

Initially, I wanted to call this compressor the best in terms of performance - after all, the characteristics stated an impressive figure of 412 l/min. But, unfortunately, at the end it drops to 288, which is the average value in this category. However, most users are still interested in the unit, since its inherent set of characteristics ( operating pressure 8 bar, 50-liter air reservoir and notorious performance) allows it to be successfully used for painting cars in service stations. Moreover, the model is praised for its reliability - it was bought several years ago, and all this time it worked flawlessly (subject to timely oil changes).

The device is equipped air filter To protect internal components from dust penetration, the welds of the receiver, the casting of the cylinders and the engine itself are very high quality. Appearance The unit does not in any way indicate its Chinese origin - the elements fit well, there is no play or siphonage anywhere. The design provides universal “rapid” type outputs for simultaneous connection of 2 consumers. Contrary to advertising, the compressor, weighing 48 kg and measuring 76.5 x 34 x 71.5 cm (WHD), cannot be called light or compact, but the presence of a handle and two wheels makes it much easier to transport.

1 ABAC Montecarlo L25P

Improved piston head. High working pressure
Country: Italy
Average price: 18,500 rub.
Rating (2019): 4.9

In the 90s, Italian ABAC compressors made a real splash in the Russian market– unlike domestic Soviet-style units, they were incredibly light, compact and powerful. Today, of course, the situation has changed, but the championship still belongs to purebred “Italians” like the ABAC Montecarlo L25P. It is designed to operate with variable pressure from 2 to 10 bar, which fully satisfies most compressed air supply needs. air environment. The device is equipped with a 50 l receiver, single-phase electric motor power 1.9 kW, two pressure gauges, large transport wheels and a handle.

The developers used in the design of the piston head modern technologies: used for better cooling aluminum alloys and enlarged the cooling fins, equipped the piston with graphite-Teflon rings, characterized by a low coefficient of friction and high wear resistance. By doing this, they achieved a significant increase in compressor life, especially under cold start conditions.

The best compressors for professional use

If you paint passenger and truck cars professionally, you will have to forget about inexpensive direct-drive compressors. Car painters need high-power units with a belt drive that do not overheat. They are equipped with similar engines, but due to the difference in pulley diameters, the crankshaft turns much more slowly, therefore, the air injection part does not overheat, and the compressor group has time to be well lubricated. This allows compressors of this category to be used in a more intensive mode, but it must be taken into account that continuous operation is still unacceptable.

4 Bezhetsk plant ASO S-416M

A stationary unit recognized as the best product in Russia. Powerful electric motor
Country Russia
Average price: 107,000 rub.
Rating (2019): 4.4

The S-416M compressor unit is intended for use in construction, road enterprises and motor vehicles. The equipment consists of a 430 liter receiver, an 11 kW electric motor installed on it and a 4-cylinder 2-stage compressor head capable of pumping up to 1000 l/min. air at a pressure of 10 bar. The compression process occurs evenly throughout the entire volume of the chamber, so the level of noise and vibration is minimized, and installation of the compressor does not require the preparation of a special foundation.

The compressor is fully repairable; its piston group is made on the basis of car engine elements. To increase the trouble-free service life, simple scheduled maintenance is required every 200 (TO-1) and 500-700 (TO-2) operating hours: flushing the crankcase, tightening the bolts, changing the oil and, if necessary, filters. In general, the unit is considered to be of high quality, reliable and durable, as evidenced by the diploma of the All-Russian competition “100 best products Russia", received in 2004.

3 ABAC 6000/270 CT 7.5

2-stage compressor unit. Increased air flow and increased operating pressure.
Country: Italy
Average price: 89,700 rub.
Rating (2019): 4.5

In line professional series For compressor equipment from ABAC, we have selected the model 6000/270 CT 7.5. It is notable for its reasonable price relative to its technical characteristics and its ability to create an air flow of 827 l/min. under operating pressure 11 bar. The piston block design consists of two cylinders different diameters, providing 2-stage air compression. This solution provides several advantages in comparison with single-stage compressors: economical energy consumption, high performance and efficient heat removal, which increases the service life.

The device is suitable for professional painting auto, crushing, nut tightening, sandblasting and other semi-industrial tasks. Its reliability and durability are combined with high level comfort - a clear indication of the oil level is provided, a regulator with a pressure gauge is installed for quick and accurate adjustment of the outlet pressure, the transportation unit of two rear wheels and a front rotary one is well thought out. Operational safety is ensured by an automatic unit, the functions of which include turning off the compressor when the maximum pressure reaches and turning it on when it drops to the minimum required.

2 Remeza SB4/C-100.LB75

Lacme three-cylinder piston block. Starting at reduced mains voltage
A country: Republic of Belarus
Average price: 65,400 rub.
Rating (2019): 4.8

The Belarusian plant of compressor equipment "Remeza" has been known since 1989 and during this time has managed to become an exporter to 25 countries. His models were famous for their pleasant combination of high technical parameters and affordable cost. However, the SB4/C-100.LB75 model has one more difference - the ability to operate stably at low mains voltage (from 180V). But many car services are located on the territory of small enterprises, where powerful equipment causes a voltage drop, or are even located in garage cooperatives with unstable power grid characteristics. Using conventional compressors in such conditions is fraught with their failure.

Thanks to its design features (3-phase motor with a power of 5.5 kW, cast iron compressor block from the French company Lacme, receiver with a volume of 100 l), the model “blows” 10 bar with an output capacity of 616 l/min. and easily powers any pneumatic equipment, be it a car paint gun, a grinder or a pneumatic hammer. The high-quality assembly of the product is visible to the naked eye, the receiver has been painted in the best possible way, and it is not afraid of either dirt or corrosion.

1 FIAC AB 100-360

Minimal oil carryover. Quiet operation. Availability of all spare parts
A country: Italy (produced in Belarus)
Average price: 29990 rub.
Rating (2019): 4.8

The AB series of single-stage oil compressors are designed specifically for intensive (up to 8 hours/day) operation in small industries. The compressor group of the AB 100-360 model produces a capacity of 252 l/min, is complemented by a 100-liter receiver and consists of two honed cylinders, resulting in better oil retention on the walls and less consumption. A specially developed Fast Valve valve design has also been introduced, which provides minimal operating noise (74 dB) and is considered more reliable than conventional valves.

The Italian manufacturer FIAC has long been known in Russia and has a wide network of specialized service centers. They work closely with Italian engineers, maintain warehouses with a full range of spare parts and quickly resolve various technical problems. This is confirmed by reviews - about shortages or long delivery times Supplies and no one complains about the details. In general, the compressor is characterized as a high-performance, safe and durable machine, however, to maximize its service life, you should adhere to the recommended operating mode - 5 minutes and 5 minutes of rest.

	Silent oil compressors for short periods of operation The BB series of oil compressors is designed for applications where the main user requirements are extremely low noise and high efficiency. With a sound level of only 40db (this is approximately the work of a modern domestic refrigerator) and almost complete absence of vibrations, BB series compressors can be located in close proximity to the operator without creating any noise problems for him.
	Silent oil compressors that prevent oil from entering the compressed air. The series is designed for cases where particularly clean compressed air and silence in the room are required. The heart of MD compressors is the T75 air module, which is 50% more efficient than other systems with the same noise level. This is the only oil compressor unit in the world supplied with unique piston rings,do not allow oil to enter the air.
	Silent oil-free compressors PT - a series of oil-free compressors made according to innovative technology, is ideal for applications that require minimal maintenance, low noise levels and a guaranteed absence of oil in the air.
	Efficient oil-free compressors VT is a series of low-noise, oil-free compressors with increased performance. The heart of these units is the V-twin air module, the quietest of any powerful oil-free compressor, designed to latest technology"inclined piston".
	Efficient, low-noise, oil-free compressors In cases where a high capacity compressor must be installed close to the operator, the VTS series is recommended. Models in this series are built on the basis of VT compressors, but are equipped with a casing that significantly reduces noise levels and allows the device to better fit into the interior of a laboratory or workplace.

Industrial production

The BAMBI silent compressor is an independent, completely self-sufficient air center, created by BAMBI engineers using the most advanced technologies.

BAMBI offers a wide the lineup silent compressors suitable for your special task, as well as for any standard applications where clean compressed air, comfort, high reliability and efficiency are required.

Laboratories

BAMBI compressors are especially in demand in cases of critical use. This application is found in research laboratories with unique equipment. To achieve this, BAMBI not only produces reliable systems, but also provides high-quality service, as well as meeting the specific requirements of each specific application.

Medicine and Dentistry

Ideally clean air, complete absence of oil contamination, low noise level - these are standard requirements for modern medical equipment.

For many years, BAMBI has been developing to advance compressors in this sector, and BAMBI systems fully meet the requirements of modern surgery.

BAMBI compressors provide hygienically clean air and are easily connected to any medical equipment.

Silent oil compressors

The BB and MD series are designed for those users who require compressors with extremely low noise levels, maximum efficiency and designed for long-term trouble-free operation.

Although both series compressors have an oil-based power module, the MD series has unique piston rings designed to eliminate oil from entering the compressed air, allowing it to be used in medical, dental and laboratory applications and making it the only silent compressor of its type on the market.

Compressors of these series are equipped as standard with a receiver with internal coating, silent check valve, 10 micron outlet filter, pressure regulator, and many other devices.

Series BB

These compressors are the most inexpensive of all BAMBI compressors. They have the same pump block and different receivers, pump blocks may be for greater performance. The features of this series include an extremely low noise level, like a modern refrigerator. The pumps of these compressors are placed in a metal casing, the crankcase of which is filled with special oil. The engine and pump itself hang on springs inside the casing, drawing oil through the combined crankshaft and engine shaft. In this way, all parts of the compressor are lubricated; additional oil is sprayed into the casing space, lubricating the cylinder and piston through the air intake.

The compressor piston does not have oil scraper rings to increase reliability and simplify the design. Due to these features, BB compressors pass oil into the compressed air, consuming it from the crankcase. The oil level must be monitored, especially if the compressor operates for a long time. The fact is that oil consumption increases greatly with increasing pump temperature; the oil level can be monitored through a special transparent window. Compressors of this series are not recommended for full-time use, much less around the clock. They are suitable for you if you use a compressor to power, for example, a pneumatic dispenser or for infrequent use.

The BB series is not suitable for applications requiring air free of oil and condensation. If the compressor heats up noticeably, oil particles enter the compressed air and fill the room with a characteristic odor.

MD Series

This is a series of small compressors, similar to BB compressors, but with a significant advantage - they do not leak oil into the air. That is, with low noise and vibration levels and durable design, they do not require regular addition of oil. The pumps release so little oil into the air that such compressors can be used in dental clinics without the patient smelling the oil.

HT Series

Compressors in this series are oil-free compressors with a low noise level, compared to ordinary similar compressors. The noise spectrum is not at all similar to the noise from a refrigerator; it is more like the noise from an ordinary compressor, only noticeably quieter. These compressors do not release oil into the air and require no maintenance at all, except for draining the condensate from the receiver. this comes at the cost of a shorter service life. These compressors are not recommended for all-day operation as they do not have forced cooling pumps. A version is available with double the crankshaft speed for greater performance (-2P), which again comes at the expense of service life and noise levels.

VT and VTS series

This series belongs to the class of productive industrial piston compressors. Compressors in this series can operate around the clock, thanks to a forced cooling fan. All compressor components are extremely reliable. The compressor pump is oil-free, so the compressor requires minimal maintenance, in particular draining condensate. All models can be equipped with a condenser dehumidifier for completely dry air output. This produces compressed air that is absolutely free of oil and moisture. VTS models have a sound-absorbing casing that somewhat reduces the noise level from powerful pumps.