Thanks to their thoughtful design, sliding wardrobes save a huge amount of usable space. The “Basya” sliding wardrobes performed especially well.

How to assemble a wardrobe?

Assembling the Basya sliding wardrobe does not present any difficulties for a person who knows how to use tools. Such furniture can be placed not only in the bedroom, but also in the country house or in the hallway; everywhere this furniture will look completely relaxed and organic.

“Basya” perfectly matches the format of budget furniture. Compared to other Basya models, it costs two and a half times less, but it also looks very presentable.

Instructions for assembling the wardrobe are included with each unit of product, but difficulties still arise from time to time in its layout, especially in the question of how to assemble a wardrobe for a beginner. In addition to the manual, it is recommended to watch the video materials on the website, which show in detail how to assemble the Basya wardrobe.

Wardrobe diagram "Basya"

The “Basya” cabinet is assembled as follows:

1. First, the frame is installed. All cabinet components are marked and numbered, so it will be easy to work. Assembly begins from the bottom corner. The side wall is connected to the bottom using self-tapping screws, and another wall is installed in parallel nearby. Before doing this, it is better to look at the photo in the instructions.
2. After the frame is assembled, the back wall comes into play, which is attached with small nails to the assembled base. Also, instead of nails, 3 mm screws are often used.
3. The product should be assembled from top to bottom, the wall is fixed on both sides, it gives rigidity and stability to the entire structure. It is very important to control that there are no distortions. For these purposes, use the following tool:

• construction square;
• good meter level;
• roulette;
• plumb line

If there is the slightest distortion, the door will not close well and it will be impossible to fully use the cabinet.

1 2 3

The assembled frame is prepared, which means it’s time to attach the back panel; it is attached both from the outside and from the inside. After completing this assembly phase, it is recommended to test how smoothly all the elements are fastened, and if something is done incorrectly, this will negatively affect the operation of the product, and the service life will be noticeably reduced.

1. After the frame is installed, the installation of the shelves begins. They are fixed with the help of special cylindrical wooden blocks, which are called chopiks. Moment glue, screws, and dowels are also actively used. It should be noted that all markings are on standard parts, so the process of installing blocks does not present any difficulty.
2. The most important step is the door layout. It is very important that there are no distortions, then the door will close and open normally without effort. In this case, it is important to install the guides correctly.
3. After the door is installed, a mirror is mounted on it. How to attach a mirror, it is recommended to look at the assembly diagram of the Basya sliding wardrobe with a mirror.
4. After the assemblers have completed the main work, the fittings can be installed.

As you can see, the description is quite accessible even for a primary school student. You can determine the correct installation of the Basya wardrobe by some characteristic features:

• the product rests on the floor, without any distortions;
• there are no gaps at the joints;
• the door opens and closes silently without any effort.

Having made sure that everything is fine, the “Basya” cabinet can be safely used, loading it with contents.

Assembling furniture yourself can help you save a lot of money cash. It’s good if a person has simple skills in assembling objects. It will be useful for beginners to learn how to assemble a wardrobe themselves. Step by Step Actions installation of each element of the product will allow for quick installation.

Among all types of clothing storage products, the leading place today is occupied by the wardrobe. It is multifunctional, spacious, and comes in different forms and sizes, and also does not require additional space to open doors. That is why most people, when choosing between a wardrobe and a sliding wardrobe, prefer the latter option.

Assembling a sliding wardrobe with your own hands in the video presented is not at all difficult - all you need to do is have the necessary tools in your apartment and be familiar with the design of the product. Often, when ordering a cabinet without the services of assemblers, the company sends a document that contains a drawing of the product. This also lists all the component parts, which are numbered in order. By looking at the drawing and comparing the elements of the cabinet, you can intuitively assemble the product.

To work according to the sliding wardrobe assembly diagram, you will need the following tools:

• building level– to check the levelness of the installation parallel to the floor;
• corner;
• rubber and regular hammer;
• straight and Phillips screwdriver;
• roulette;
• pencil and ruler;
• screwdriver;
• wood drill - to make holes;
• metal drill – for installing an aluminum base.

Additional tools for assembling furniture yourself include a jigsaw, drill and sandpaper. It is also necessary to prepare all the details of the cabinet, which means checking the diagram to ensure that the number of items matches. Pay attention to the fittings and mechanisms: if there are drawers in the closet, ball guides should be included.

Doors for the product are often supplied ready-made. They are pre-installed with rollers and strip soft material. The door must be installed in the final phase.

Tools

Assembly steps

To know where to start, it’s worth familiarizing yourself with its stages. Most sliding wardrobes are assembled according to the following algorithm:

• base;
• frame;
• installation of the rear wall;
• installation of shelves and guides;
• installation of compartment doors.

After the completed stages, the implementation of internal additional elements. These include pull-out baskets, drawers, rods, hanging hooks and pantographs. Let's consider the installation of each cabinet element separately.

Assembly steps

Base

The assembly of sliding wardrobes, the video of which is presented below, begins from the bottom part, which bears the entire load during operation. We find a part that will perform this function and place it in front of us. In order for the process to proceed correctly, we use tools such as screwdrivers or a screwdriver, a hexagon, a pencil and a tape measure for marking. Also check the package for the presence of self-tapping screws and special masking plugs.

The algorithm of actions looks like this:

• on the part for the bottom, the place for installing the base is marked;
• sometimes, instead of base strips, adjustable legs are used, the place for which also needs to be marked;
• drill holes for fasteners;
• we attach the bottom to the slats using confirmata (corners) - for this we use self-tapping screws and a screwdriver;
• We assemble the transverse supports of the plinth, designed for stability.

Some products, such as the Phoenix coupe model, require installation using adjustable legs. This is easy to do: the plastic plugs are cut off with a knife, and the legs themselves are screwed into holes prepared at the bottom with a diameter of 10 mm.

Depending on the size of the assembled wardrobe, the number of legs will be adjusted. So, for large planes more than 6 support elements will be required.

Preliminary marking of the cabinet base

The easiest way to assemble the base is on furniture metal corners

Installing the feet

Finished plinth with legs

Frame

Before disassembling and assembling sliding wardrobes from scratch, it is important to familiarize yourself with general structure existing product. Study the diagram carefully, because the assembly of the case should ensure safe operation closet The stability of the internal elements will depend on how securely it is installed.

In order for the furniture assembly to be accurate, you should additionally check the floor surface for evenness. Use a building level: if there are differences on the floor, tighten the adjustable legs. Only after this assemble the product box.

To ensure quality installation of the housing, follow these steps:

• It is better to assemble the product while standing, because it is very difficult to install a perfectly fitted cabinet in a lying position. But it is important to remember that for complete assembly it is necessary to leave at least 100 mm for the installation of the roof;
• in the part that is responsible for the bottom, you must first drill several holes and insert anchors. Rack strips will be mounted on the installed fasteners;
• Installation of stand-up panels is carried out by two people: in order not to get confused, you can view the instructions for assembling the sliding wardrobe presented in the video. The left side panel is inserted first, one person holds it while the second person inserts the right side panel;
• on next stage the middle stand is mounted, if present. After its installation, the roof is installed. If the cabinet is assembled in a standing position, then this part will be properly secured to the corners or confirmations.

It is a little more difficult to assemble a maestro model sliding wardrobe, which has many functions. Its installation is carried out slowly, preferably by several people.

Fastening occurs using euroscrews

Installing the side and interior walls of the cabinet

The base is connected to the body using confirmat corners

Rear wall installation

To assemble the coupe yourself, in particular to attach back wall products, you need to choose wisely Consumables– fasteners. Often, assemblers use incorrectly selected consumables, which is why, over time, the fiberboard panel comes away from the furniture product. In Soviet times, hardboard was assembled onto the back wall using nails, which is undesirable to do today.

For greater reliability, attach the fiberboard wall to the cabinet using self-tapping screws. This is how the product will not be damaged during operation.

When assembling furniture for yourself, it is important to carry out high-quality assembly of the sliding wardrobe with your own hands: the video presented below clearly shows all the complex nuances. Perform the following manipulations:

• place a hardboard panel behind the cabinet;
• Holding the sheet with your hands, use short self-tapping screws and use a screwdriver or screwdriver to screw them in at a distance of 10-20 cm.

If the cabinet has several back walls at once, they must be secured end-to-end. Use special tightening fasteners, and then screw the screws into the back of the middle bar.

Rear wall mounting

Installation of shelves and guides

To avoid having to disassemble the product and redo your work, check the reliability and stability of the frame, and then proceed to fill it with internal elements: shelves, rods, drawers and guides. Study self-assembly you can see the wardrobe using the video at the bottom of the article. It clearly provides information about all important points process.

You should pay attention to the following nuances:

• The shelves can be secured using corners and self-tapping screws. To do this, the parts themselves already have drilled holes. First, we note the distance between the shelves and attach them to the sidewalls and the central stand bar;
• First, the upper door rails are installed, after which the lower rails are installed. It is worth emphasizing that the installation of these elements must be carried out strictly in a straight line - the correct movement of the doors will depend on this;
• The rod is installed on special flanges that come with it. If necessary, the length of the pipe is cut with a hacksaw. If you are assembling a Fortune model cabinet, you should pay attention to a large number of elements and do not confuse them;
• drawers and pull-out baskets are inserted into the product after attaching the mechanisms for their operation.

Before you install it yourself internal filling, check the availability of all accessories and consumables.

Guide sliding system

Preparing holes on the guides

Before installing the guides, the stopper must be positioned correctly

In this article you can get acquainted with step by step instructions assembling a wardrobe and saving money on the service of furniture assemblers.

Before assembly, in order to avoid scratching the cabinet parts or the floor, we recommend covering the floor with the cabinet packaging.

Screw the plinth to the bottom of the cabinet. Make sure that the corners are right and that the distance from the edge of the bottom is the same along the entire length.

Now we fill in the support nails.

Assembling the cabinet body

As a rule, sliding wardrobes, like all furniture, are assembled in the lying position of the cabinet. Study carefully the assembly diagram of the sliding wardrobe. Most often, all cabinet parts and fittings have their own designation. It is also important to follow the cabinet assembly sequence indicated in the diagram. Otherwise, it may be necessary to disassemble previously fastened parts and reassemble them in the required sequence.

When assembling a cabinet, a simple mistake is often made, which is costly - they confuse the top and bottom of the parts. As a result, sometimes you have to practically disassemble assembled wardrobe and reassemble it. Make sure that the holes in vertical rack the fastenings and shelf supports corresponded to the opposite rack.

The cabinet is assembled using minifixes. It is very important until the cabinet body is completely assembled to prevent distortion of already screwed parts, as they can simply be broken off.

It is important to tighten the minifixes completely. Minifixes are always doubled with a dowel to strengthen the fastening.

Installing the rear wall of the cabinet

Once the main cabinet body parts are assembled, the cabinet must be turned face down. It is better to start assembling the cabinet with the front part facing the floor, so as not to scratch the furniture.

Before attaching the fiberboard back wall, which will give rigidity to the cabinet, you need to make sure that all corners of the sliding wardrobe are 90 degrees. Otherwise, the cabinet will stand crookedly and the doors will not close tightly. To do this, you need to measure the length of the diagonals as indicated in the figure in red. The distance from the corners should be the same. Now you can attach the wall. In order to avoid the fiberboard coming off, as often happens, the back wall should be secured not with nails, but with self-tapping screws or long staples construction stapler. Make sure that the self-tapping screws (staples), after passing through the fiberboard, do not go past the end of the chipboard.

Place the cabinet in a vertical position. Better closet lift with an assistant so as not to harm your health and not drop the cabinet. Be careful not to touch the chandelier.

Now you can attach the shelf supports and hanger pipe. We attach the drawer guides.

It is important that the heads of the screws are fully recessed, as they can interfere with the movement of the rollers of the retractable shelves.

Shelf holders often have several levels of shelf height.

Now that the body of the sliding wardrobe has been assembled, you can install it in the place where it will stand.

If cabinet supports are provided that are height-adjustable, set the cabinet level. If the supports are not adjustable, as in this cabinet, and the floor is crooked, the level can be set by placing it under the plinth dense material. If the cabinet does not stand level and stable, the doors will close poorly and not tightly.

Installation of sliding wardrobe doors

First we attach the top guide. If there are no holes for self-tapping screws, they must be drilled with a drill with a diameter of 4 mm. There are two holes on the edges and one in the middle.

The top guide is mounted flush with the edge of the cabinet lid.

We also make three holes in the bottom guide. Having drilled a hole for the self-tapping screw, carefully remove the chamfer with a drill of a larger diameter so that the self-tapping screw is “recessed”. Before fixing the bottom guide, do not forget to insert two springs into it that secure the door rollers.

When installing doors, first start top part doors into the upper guides, then insert the lower rollers into the rails.

Now you can adjust the tilt of the doors using a hex key. IN last resort removed protective film from door profiles and guides sliding system. We glue the sealing brush to the ends of the doors. If you touch the end where the brush is glued with your hands, the brush will stick worse, since your hands leave grease.

Hello again. Today we will assemble our wardrobe, we will do this according to the instructions below.

So, we took the parts from the cut. We didn’t want to glue the edge ourselves, so we ordered gluing there, especially since the price of gluing is not that high.

We also bought all necessary fittings for the cabinet and the necessary fasteners.

The floor turned out to be not entirely level, so the cabinet had to be built not on a plinth, but on adjustable legs; accordingly, the detailing was slightly altered.

The introductory part is finished, let's start assembling.

Wardrobe assembly instructions

Our procedure for assembling the wardrobe will be as follows.

You need to start assembling from the bottom of the cabinet, namely by assembling the base and installing the legs.

We take a part called the bottom and mark its lower side for installing the base and legs as shown in the diagram below:

The plinth can be secured to the bottom using mini fixes (eccentrics, rasteks - whoever calls them), confirmats or regular ones plastic corners.

Since this will still be an invisible area, and the cabinet will not stand on a plinth, but on legs, I decided to secure the plinth using plastic corners. The legs were secured with 3.5*30 screws.

Just when you screw the legs, don’t overdo it (you can over-tighten it, and the sharp part of the screw will come out from the back side).

We attach the four parts of the base to each other using confirmations. For convenience, take yourself corner clamp. You can use it.

Do not twist the front plinth with corners, as To adjust the legs you will have to remove it.

We will attach the sides to the bottom and roof with minifixes. They are great for fastening perpendicular parts, and they also manage to completely hide the fastener.

If space allows, it is convenient to assemble the sliding wardrobe lying on the front part and fasten it using confirmations. But since I didn’t have any free space in my room, I had to assemble it standing up and use eccentrics (rastexes, minifixes) as fasteners.

On the bottom and roof of the cabinet (from the inside) we mark holes for installing the minifix rod.

Before installing the sides, using a level, the bottom of the wardrobe must be leveled as evenly as possible. Simply lean the level and adjust the legs to the maximum horizontal position.

Now you need to mark the sidewalls, the holes should exactly coincide with the installed rods on the bottom and roof. In the sidewalls you will need to do two different drillings in two different planes.

The first hole is made for a metal eccentric, which will tighten the rod; it is made in inside sidewalls, with a special 15mm cutter, at a distance from the edge of the end to the center of 34mm (this is if the rod has a total length of 44mm, like mine).

In general, when fitting a part onto a rod, its head should protrude 6 mm. If this is your first time installing minifixes, practice better on rough parts, so you will feel more confident when assembling.

The second hole is made at the end of the part, with a 6-6.5 mm drill, strictly in the center (8 mm from the edge).

For a more detailed understanding of this assembly step, you can use our materials on.

• When you've done everything required holes, do not rush to install the sides and roof right away.
• To give the structure initial rigidity, immediately assemble the central partition with the upper shelf (we fasten it with confirmations).
• At the next stage, we need to place the sidewalls, the rear wall of the console and the assembled T-shaped partition on the lower rods, tighten them with eccentrics, and secure the upper shelf to the sidewalls (with confirms). Use an angle clamp for support.
• Next, we attach the roof and check the verticality using a level.
• If everything is fine, to provide additional rigidity, we install additional shelves using confirmats.
• Now, using 3.5*16 screws, we fasten the back wall of the fiberboard. Let's start with two upper corners, and after perfect alignment, we begin to screw in screws throughout the entire box, in increments of 15-20mm. The fiberboard should also be secured to the central partition and the top shelf.

The hardest part of the job is finished. We put the cabinet in its place, once again check the position of the cabinet by level and proceed to installing shelves, hangers and drawers.

Shelves can be made either rigid (secured with confirmations) or removable (on shelf holders).

To have fewer plugs for holes on the visible side of the wardrobe, I decided to install the shelves on shelf holders.

Everything is simple here. We mark on the sidewall the desired height, using a 4.5-5 mm drill, we make a NOT through hole, up to 8 mm deep, and hammer the shelf holder into it.

Download video and cut mp3 - we make it easy!

Our website is a great tool for entertainment and relaxation! You can always view and download online videos, funny videos, hidden camera videos, feature films, documentaries, amateur and home videos, music videos, videos about football, sports, accidents and disasters, humor, music, cartoons, anime, TV series and many other videos are completely free and without registration. Convert this video to mp3 and other formats: mp3, aac, m4a, ogg, wma, mp4, 3gp, avi, flv, mpg and wmv. Online Radio is a selection of radio stations by country, style and quality. Online Jokes are popular jokes to choose from by style. Cutting mp3 into ringtones online. Video converter to mp3 and other formats. Online Television - these are popular TV channels to choose from. TV channels are broadcast absolutely free in real time - broadcast online.