A rocking chair can be made of metal, wood, plastic or plywood. However, if you are going to build a rocking chair yourself, then in this case preference should be given to plywood. This is explained by the fact that it will be easiest to draw up a drawing for a rocking chair made of plywood.

Advantages of plywood

• moisture resistance;
• durability (a plywood product will not lose its attractiveness even after 10-15 years);
• environmental friendliness of the material;
• does not require special care;
• easy to saw;
• low cost;
• the material bends well.

Blueprints

If you are going to build a rocking chair yourself, then preference should be given to a simple model, which consists of two sidewalls and transverse components.

First, stencils are made from the cordon, which will later be used to cut out parts from plywood (bars, support strips and sidewalls). To do this, you will need a sheet of glued veneer, about 17 mm thick.

Important! Particular attention should be paid to measuring the sidewalls, since they form the basis of the entire structure (the sidewalls have a curved shape and not a constant width, so calculations may be difficult).

The cardboard template is drawn “by eye”. Standard sizes transverse components 0.7 m in width and 0.6 m in length. However, the size can be changed if desired. Standard support length is 0.07 m.

After the stencil is made, it must be tested, that is, it must be installed on flat surface and shake it. This is necessary in order to understand what the original will look like.

What will you need for work?

To work you will need:

• plywood sheets about twenty millimeters thick;
• iron rims, nails and screws;
• “sandpaper”, masking tape;
• electric drill and electric jigsaw;
• glue, foam rubber, leatherette;
• paint, stain.

Making the base

Process:

• Trace a stencil on plywood. Then the part is cut out according to the mark. Thus, the first sidewall is obtained. The second one is made identically to the first one.

Simple model of a chair (cell scale 1:10)

Important! Both sides must be the same size.

• The cut out element is sanded with sandpaper.
• The supports are attached to the sides using glue. Then the parts are fixed with self-tapping screws.

Important! The bars must be parallel to each other. In the future, the backrest will be attached to them.

• Using self-tapping screws, attach the first plank to the upper bars. The remaining strips are installed in the same way.

Finishing

The process of finishing a rocking chair made of plywood:

1. The outer side of the product can be painted with stain in one or two layers.
2. The inner parts of the sides and ends can be painted with black paint.
3. After the paint has dried, the ends are reinforced with iron rims.
4. To give the chair softness, it is necessary to use leatherette. The leather is first used to trim the back of the back.
5. Nails are used to attach the leatherette to the frame.
6. To make the soft part, foam rubber (8 mm thick) is used, which is cut to fit the backrest. Then it is placed in a leatherette case. Using glue, the mattress is attached to the backrest.

If the drawings were drawn up correctly, the result will be an attractive and comfortable rocking chair. It is worth noting that this is not the only option; there are other more complex models.

Reading time ≈ 5 minutes

This article is step by step instructions on how to independently make a metal rocking chair, which also contains photos and videos. Thanks to detailed explanations, you will not go wrong with the choice of materials, and you may also gain new skills that will be useful in future projects.

Materials for making a rocking chair with your own hands

The first thing you need to do is purchase the metal parts for your future rocking chair. You may need to get someone to make you the exact frame shape you need. If you work together with a professional, he will be able to give helpful advice, help with the choice of materials, etc.

Ideal for frame homemade rocking chair the metal will become a 20 mm (in diameter) steel rod. If you find that the rod is too heavy for the frame, you can use steel pipes.

As a result, as you can see in the photo, you should end up with a set of rods of the following sizes (pay attention to the drawings):

• A: 4 x 650 mm
• B: 2 x 268 mm
• C: 2 x 867 mm
• D: 2 x 600 mm
• E: 2 x 896 mm

Of course, you can change the dimensions of a rocking chair made of metal, but be careful in your calculations.

Fitting metal rods

In order for each steel element of the future frame to fit tightly together after welding, their ends need to be adjusted (to understand exactly how to do this, watch the video presented on the site). This will be easy to do if you have a desktop one. As a result, you should get the following:

• ‘A’ rods ground on both ends
• ‘B’ rods ground on one side
• ‘C’ rods ground on one side
• ‘D’ rods do not require grinding
• ‘E’ rods do not require grinding

Welds

Start by connecting the rods of the two sides of the rocking chair (B, C, D) as shown in the photo. It is better to do this on the floor in order to ensure perfect smooth structure. If you have a magnetic welding square, use it. Otherwise use cinder block to achieve an angle of 90º.

After welding the two sides (B, C, D), connect them with rods A.

Shaping

Figuring out how to bend a 20mm diameter steel rod requires a little imagination. Especially if you don't have any special tool like a pipe bender. You will need a pipe and a tree with a forked trunk (as you can see from the photo, the trunks should be close to each other). Place the rod between the trunks and slide the pipe onto it. By holding onto the latter and applying pressure, you will gradually be able to give the rod the desired shape. Try to keep the 'E' parts as similar as possible to each other.

Attach the ‘E’ curves

A durable frame for a metal rocking chair, made by yourself, is almost ready. Now you need to weld parts ‘E’, then ‘D’ and ‘B’ (most likely, they will need to be adjusted quite a bit to the curved ‘E’). The most difficult part of the journey is over!

Sling test on frame

If someone close to you has sewing skills, entrust the creation of the cover to one of them. You can use an old blanket or a durable blanket, from which you will need to cut a 600 mm strip. It should be sewn to the two upper rods ‘A’ so that you get a kind of sling in which you will sit. Very simple and great!

Stripping

If your welds are similar to those shown in the photo, you will agree that such a rocking chair will not have the most attractive appearance. Sanding the seams will take some time, but the results are worth it.

Painting

This is probably the most enjoyable part of the whole job. But first, thoroughly clean the chair frame with hot soapy water to remove dirt and grease. Rinse afterwards clean water and let dry completely.

Hang the frame wherever it is convenient for you. It is better to paint on a warm, not too windy day. The first and second layers will be primer (ground base). But the second one is applied a few hours after the first one. Next comes two layers of base primer (third and fourth), which are applied 24 hours after the primer base. It is better that the last two layers are gray. As a result, appearance a finished rocking chair will be much more impressive. After this, apply matte varnish.

Sling color selection

What color your rocking chair will be is up to you. It is desirable that it be a durable 100% cotton material. By the way, if you already have a piece of light-colored fabric, you can only purchase a special dye and, following the instructions, give it the desired shade.

Sewing a sling

In terms of dimensions, you will need a piece that is 1200mm wide and approximately 1300mm long. It will need to be folded in half so that the result is a rectangle of 600x1300 mm. Two long sides The rectangles are sewn together, and the resulting sleeve is turned inside out. Each end of the sleeve is also sewn up with the cut edges inward (as in the photo) in order to prevent the sling from quickly wearing out.

Secondly, a simple and at the same time effective health simulator. Thirdly, it is surprisingly comfortable to relax in, read a book or indulge in sweet, addictive and enveloping laziness.

Since the statement that all diseases stem from nerves is largely true, a rocking chair can become a unique pill, a miracle cure for many diseases.

Rhythmic, uniform and calm swaying puts the human nervous system into some semblance of a trance - the body calms down, relaxes, but the parasympathetic nervous system just the opposite - it is activated.

A person relaxes, distracted from the daily routine and obsessive thoughts. A relaxed mind is “lazy” to control the body, the muscles relax, beginning to fully rest and recover, accumulating a reserve of strength.

A rocking chair will help overcome sleep problems, because measured rocking is the same manipulations that a mother performs when rocking her child to sleep. cradle. Just half an hour in a rocking chair - and deep healthy sleep will take you into his arms.

A rocking chair will help patients with tachycardia - rocking seems to set a certain uniform pace to which the heart adjusts. It trains the vestibular apparatus - after it it is easier to endure long trips in a car, train or plane.

Today, rocking chairs are made from different materials, but our most popular products are from rattan and vines.

What to make a rocking chair from: selecting materials

To make a reliable, strong and durable rocking chair, you need to use high-quality wood - coniferous varieties, oak or larch. Often, to simplify the work, plywood is used - its sheets are not only easy to saw to obtain a part of the required shape, but it is also quite plastic and lends itself well to further processing (sanding, painting).

The choice of material is almost entirely determined by the location where the rocking chair will be placed. An outdoor rocking chair must have additional protection and treated with antiseptic agents that minimize the impact of adverse aggressive natural factors(frost, rain, snow) and will allow you to maintain aesthetic appeal for as long as possible.

For the dacha the best option It looks like a combination of metal and wood - the base (frame) is made of forged metal, and the seats are made of wood. And stores are increasingly offering plastic rocking chairs, which have two undoubted advantages: low price and high immunity to all natural influences.

How to make a rocking chair with your own hands: the most affordable options

The main part of the rocking chair design is two runners (skis) that have an arched shape, due to which, in fact, the chair can rock. These runners can be short or long. In chairs with long runners, the depth and amplitude of the swing is quite large; a person goes from a sitting position to a reclining position. Rocking chairs with short runners provide a calm and sedate rocking motion, which is why they are especially popular with older people.

To make a simple rocking chair, you don’t even need detailed drawing rocking chairs. It is enough to take a ready-made, for example an old, chair (1) with wooden legs. Let's make two supports (2), for this we make two elements from bars that will have the same curved base. We also saw out the cheeks (3), which we later use as the bottom for the chair legs.

For each leg of the original chair, we cut out two limiting bars (4) - a total of eight. We nail the appropriate stops at the required distance for each support for all legs. Both supports have outside screw in three (6) furniture bolts - this will give the chair stability and ensure safe swinging. Prepare an end plate (7) for each limiting timber. Having inserted the legs of the chair into the prepared grooves with limiters, we cover the limiters with closing plates and fix them using a hammer drill. For convenience, you can add a footrest (8) to the front.

Similarly, you can upgrade a chair with metal legs by making special fastening loops from metal

Plywood rocking chair

For plastic modeling, plywood is the most favorable material. Using a jigsaw, you can get a design that will greatly simplify the process, because structurally it combines the two most important (and most difficult to manufacture) elements of a rocking chair - the runners and the sides. In addition, the absence of joints significantly increases the strength of the structure.

For production we will need:

• jigsaw
• screwdriver
• plywood – sheet at least 15 mm thick
• oak (pine) slats with a cross-section of 10x50 mm - about 20-35 pieces, the length depends on the manufacturing option - a single or double chair. For a single seat, the length of the rail is 1200 mm.
• timber (pine, preferably oak) – 30x50 mm, 3 pieces, equal in length to the slats
• self-tapping screws

We draw a pattern on graph paper, transfer the design to plywood and cut out the side panel with a jigsaw.

After this, we sand all the parts and remove small chamfers. If the rocking chair is intended for a summer residence, Special attention the ends will be required - they require maximum protection from moisture. Therefore, the ends of all parts are impregnated with hot drying oil, after which the wood fibers are slightly flattened with a hammer - this way the moisture will be absorbed much less. Before the beginning general assembly The processing-varnishing procedure for the ends must be carried out twice.

We mark holes for connecting bars (tsars) at the foot, middle part and headboard. To achieve maximum accuracy, after preliminary marking, the sidewalls are aligned and a hole is drilled. The drawers are secured with Euroscrews and additionally secured with wood glue. After this, we evenly fasten the slats onto the already assembled frame with self-tapping screws. After completing the assembly, you need to fill the holes above the screws, sand all the parts again with fine sandpaper, treat them with an antiseptic, cover them with stain (if you like) dark colors wood) and coat the resulting chair with waterproof varnish.

If it is possible to use an angle grinder and welding machine, can be collected metal carcass. To do this you will need a steel corner (20x20x3 mm) and a steel strip (thickness 4 mm, width 40 mm). After assembly, the frame is painted, after which holes for self-tapping screws are drilled along the entire length of the seat and backrest, which will be used to fasten the wooden facing strips.

Advice! Before assembly, be sure to treat the metal parts with an anti-corrosion compound.

Own garden – perfect place both for work and for leisure. For a complete country holiday people have come up with a variety of devices from swings to hammocks. Armchairs are considered a classic piece of comfortable furniture. But someone brilliant managed to add an addition to its design that made it even more convenient: a rocking chair was born. This model allows you to perfectly relax all the muscles, and the leisurely and rhythmic rocking encourages pleasant thoughts, calms you down, and lulls you to sleep. The rocking chair turned out to be so popular that many variations and modifications have appeared since its invention. Moreover, it turned out that a DIY rocking chair made from different materials is not a myth.

For creating classic model Rocking chairs need willow vine. Openwork and lightweight design looks great against the backdrop of country greenery and goes well with the interior garden house or gazebos. This lightweight and durable product has one drawback - the fear of excess moisture.

Making a light and seemingly unpretentious chair from willow wicker is not so easy. You need to be able to prepare the material, and the weaving technique requires special skills

Rattan is a flexible vine that grows in Southeast Asia. Rattan is also woven into wonderful and very beautiful armchairs. They are not inferior in beauty to willow trees, which cannot be said about their strength. No screws or nails are used when creating rattan furniture. All connections are held together only thanks to glue and skillful knitting.

Rattan is not sold as a raw material in our stores. Such a rocking chair for the owner of a summer house is a good buy, and not a product in the manufacture of which he can show his creative abilities

If we talk about the strength and durability of the product, then an example of reliable furniture is this model, created from forged metal. An elegant lace structure will decorate any garden.

The main advantage of this model is its durability. The main one, but not the only one. Agree that this thing looks like an elegant silver jewelry

Rocking chairs are used not only as country furniture. Distinctive feature The features of an office rocking chair are its respectability and solidity.

Office workers also appreciate high-quality rocking chairs as accessories that help them fully relax from the hustle and bustle of business. Of course, office models differ from the country version

There are also designer models rocking chairs made in high-tech style.

Very interesting and, most importantly, enough functional model. Combines a comfortable rocking chair and a directional lamp

Some cutting-edge rocking chair designs are truly unique. Like more simple models, they guarantee their owner comfort, but, in addition, independence from energy sources. This product, equipped with solar panels, allows you to spend time with comfort and benefit.

For the base of such a structure, you can use thick plywood, and for its upper part - polycarbonate. Find on the web solar panels not a problem today either.

Master class: rocking chair for two

A two-seater rocking chair looks more like a sofa. If you put a few pillows or throw a blanket on this convenient structure, you simply won’t find anything better for a country holiday. We will tell you how to make such a rocking chair with your own hands.

Who said you can only enjoy the comfort of a rocking chair alone? This model is good for two

Stage #1 – preparing tools

Making a quality rocking chair is not as difficult as it seems. Having everything necessary tools and stocking up quality materials, you can leisurely do everything yourself. What exactly tools will we need for this work?

• Electric jigsaw complete with wood saws.
• Disc sander. It will require attachments with different grain sizes. Actually manual frezer may also be needed, but if available large quantity coarse sandpaper and provided the sander has sufficient power, you can do without it.
• Screwdriver with a set of wood drills and bits.
• A right angle with a long measuring ruler.
• Roulette.
• Hammer.
• Putty knife.
• Brushes and pencil.

Proper organization of work assumes that all of the listed tools will be literally at hand.

Stage #2 – draw a drawing

Any responsible work begins with the production of a drawing. It is necessary in order to correctly calculate the need for materials. However, the drawing already exists. On a metric grid, the pitch of which is 100mm, there is a template for the side of the chair. It is best to transfer the drawing to paper and cut out a pattern, which will make it easier to apply the outline to the plywood.

The drawing of an excellent rocking chair, which you can make with your own skillful hands, is made on a metric grid, the pitch of which is 100 mm

Small inaccuracies are acceptable, it is important not to make a mistake in the main thing: the sidewalls must be identical, there should be no protruding corners on their rolling, lower side.

Stage #3 – cutting blanks from plywood and timber

To make drawstrings and sidewalls, you will need Europlywood, the thickness of which is 30 mm. The sides, as already mentioned, are cut out with a jigsaw strictly according to the pattern. The dimensions of each of the three drawers are 800x120 mm.

Now you need to cut the blanks of the bars, which will later make up the surface of the seat and back of the rocking chair. To do this, we need a beam measuring 50x25 mm, from which we will cut 35 blanks of 1200 mm each. Before purchasing the material necessary for this, find out what the standard length of one such bar is in your stores.

Based on the proposed drawing, you need to make a pattern, with which you should apply the contour of the side of the chair on the plywood

You can easily calculate the total molding you need on your own. Observe the multiplicity so that when cutting the workpieces there is no large amount of residue. It’s better that your rocking chair turns out to be a little narrower than originally planned. For example, when standard length at 2.4 meters, the length of one workpiece will be 1195 mm (the thickness of the cut and subsequent processing are subtracted).

With fasteners everything is simple. Needed:

• confirmations (euroscrews) 12 pieces, size 5x120mm;
• self-tapping screws 140 pieces, size 4x45.

In fact, the initial part of the work is already over, but you still have to work hard to get the desired result. In the process of this work, you will need drying oil, wood varnish, putty, and antiseptic, which also need to be purchased in advance.

Stage #4 – pre-processing of parts

We proceed to sanding all the parts and removing small chamfers. If your Sander It’s powerful enough and you know how to handle it; this procedure won’t take you much time. Taking into account the fact that the rocking chair will be located outdoors, special attention must be paid to the ends of all elements in order to protect them as much as possible from dampness, to which they will undoubtedly be exposed.

Pre-treatment of parts consists not only of sanding and chamfering them. All measures must be taken to protect the end parts of the elements from rotting

The ends of the parts must be soaked in hot drying oil, and the wood fibers on them must be slightly flattened with a hammer. This way less moisture will be absorbed. For the ends, the processing-varnishing-processing procedure must be carried out twice even before the general assembly of the structure.

Stage #5 – assembly of the structure

There are no specific standards in the manufacture of this item. garden furniture not provided. The holes for the drawers are marked as required by logic: the headboard, the middle part of the outer arc of the side panel and the footboard. The drawers will be pulled to the sidewalls with the help of confirmations. To do this, preliminary markings are made on the sidewalls, after which the two sidewalls are aligned, and a through hole is drilled in their planes with an 8 mm drill. For a hole in the end of the drawer, use a 5 mm drill. Now you can tighten the chair frame using Euroscrews.

The holes for the drawers must first be marked, after which both sides are folded together and neat through holes are drilled

Now let's talk about how to drill the bars that form the seat and back of the chair. We have exactly 35 of them. It is necessary to drill 4 holes in each block (two on each side). And these are 140 symmetrical holes.

To simplify the task, we use a “jig” - a device for marking a large number of homogeneous parts. We make it very simply: we take a piece of the same timber, no shorter than 250 mm, drill holes in it for the template, the diameter of which should be the same as that of a marking pencil. We nail scraps of plywood to the end and one of the side parts of the “conductor”, which will serve as a limiter that prevents you from missing during the marking process. The "conductor" is ready.

Assembly is the most time-consuming and labor-intensive part of creating a rocking chair. However, the “jig” will help you simplify the procedure for drilling symmetrical holes

This is what the chair looks like at the final stage of work. Of course, it still cannot be used in this form. It is necessary to take measures to protect it from bad weather

The “jig” will be used to mark holes; you cannot drill through it, because a drill can break the template holes and the parts will have to be countersunk separately. If you take a 3.5x30 drill with a countersink, you can use the finished markings to make the hole as needed.

According to the drawing, there should be a gap of 15 mm between the bars. To avoid distortions, it is necessary to mark on the side of the chair the distance that will correspond to six bars along with intermediate intervals, and check that the template liners match in thickness. If they match, you can continue attaching. Otherwise, adjustments must be made. A four-millimeter wood screw holds perfectly in europlywood. But given the high frequency of fastening, it is better to use a three-millimeter drill.

Stage #6 – finishing of the finished product

The holes above the screws must be carefully filled with putty. Next in line will be treatment with an antiseptic and coating the product three times with waterproof varnish. You need to work very diligently. Remember how much work you have already put into this chair. After all, you want it to last as long as possible, right? Then try!

If you have small children, you can involve them in filling the holes above the screws, but you will have to carefully inspect the model to look for damage to eliminate them yourself

Sliding chair without runners

You probably noticed that all the models presented above have general principle work. The trick is that these rockers use curved runners as the base. How to make a rocking chair without runners? It turns out that such a possibility also exists. Watch this video and you'll get an idea of ​​exactly how it's done.

A successful invention for those who value the opportunity to relax and unwind without leaving home is a rocking chair. And if you put it in the garden, you can enjoy it twice as much.

The traditional material for such chairs is willow and its analogue, rattan. Products made from this material weigh little, are distinguished by elegant lines and a respectable price.

Modern materials can also be used in the manufacture of wicker chairs - there are options made from synthetic wicker. They are no worse than natural ones, are not at all afraid of moisture and have very long term services.

Metal chairs, despite the reliability and plasticity of the material, are too heavy. Wrought iron chair It will look great in the garden, but you will have to make a platform for it. In addition, working with metal requires certain skills; it is difficult for a beginner to make a metal chair.

Rocking chair made from pipe scraps

Rocking chair made of metal profile

Plastic chairs are affordable and attractive in appearance. To these advantages we can add resistance to wet weather, durability, and bright, non-fading color. In addition, they do not have to be repainted or processed.

For self-made Wood is best suited - an inexpensive, easy-to-work material. Upon completion of work wooden chair You can give it any color or keep its texture. For those who are thinking about making their own furniture for the first time, wood is best suited.

There are many models for home craftsmen, the simplest ones are presented below.

When designing a homemade rocking chair, the main thing is that it does not tip over when the sitter leans back. It is also important that the rocking process itself, for which the chair was made, does not force the person to strain too much.

Types of rocking chairs

The simplest type is chairs built according to the radius principle. These are the most affordable products for self-production; they are distinguished by the simplicity of manufacturing technology and design. The model presented below has a somewhat heavy and awkward appearance; this chair is suitable for the garden.

Chairs of this type are designed with a fairly low seating position, which ensures smooth rocking and safety for the seated person. If the seat is installed at a normal height, then the chair runners are equipped with bumpers - limiters of the swing amplitude. To get up from such a chair, you need to make a physical effort. And the swing itself requires some tension.

Much more stable than chairs on runners of variable curvature; they do not tip over.

Nirvana chairs are very comfortable; if you lean forward a little, it will gently “land” a person on his feet. Rockers on elliptical runners, despite their comfort, can tip over, so they are equipped with bump stops; the front one usually serves as a footrest.

There is no possibility of tipping over when rocking on reclining chairs with awnings or on elliptical runners.

Where to begin

Below is a rocking chair for the garden, which even a beginner can make with some effort. On
You can try your hand at such a model before moving on to a complex home version.

In any case, the drawing should be as simple as possible so that it can be reproduced even without much experience.

This compact chair will look great in the garden and can be placed at home without taking up much space. This simple model will be used to describe the process.

You should start with a drawing

The drawing is made on a scale grid, on which each cell corresponds to 10 cm. All markings on the sawn parts must be made in accordance with the drawing, taking into account the scale.

What can a chair be made from?

Euro plywood 3 cm thick is suitable for work.

• You need to cut out the sidewalls exactly according to the pattern, three parts for each side;
• The remaining parts are made of timber 50 mm wide and 25 mm thick. For the seat and backrest you need 35 elements made of timber, each length 120 mm;
• In order to correctly calculate how much timber you will need, you must first visit the store and see what beams are available and what their length is. Knowing the initial size of the material, it will be possible to minimize waste by varying the width of the chair;
• For example, if beams are available for sale required thickness 2.3 meters long, then you can make the chair a little narrower - cut the bars for the back and seat to 115 mm each. If the beams are slightly wider, then the chair can be made a little wider so that there are not a lot of scraps left;
• You will also need three crossbars made of timber; when making them, you should proceed from the width of the chair - that is, the length of the bars for the back and seat.

Small variations in width will not affect the stability of the chair, so you can do this without worrying about the result.

When the parts are ready

After the parts are cut, they will need to be processed. There should be no roughness on them.

In addition, carefully processed surfaces will give the product a finished look and facilitate finishing.

Surfaces are treated using grinding machine, each part must be sanded on both sides with sandpaper of different grains. If you have the skill, you can use a router attachment to soften and round the sides of each part. If this is not possible, you can simply process the cuts with a grinder or sand them manually.

Treatment with hot drying oil should be carried out in at least two layers. This is one of the most unmodern methods, but after this the product can be painted oil paint and use even outdoors, without losing its qualities and appearance.

Small parts can be dipped entirely into boiling drying oil, but you should not hold them with your hands. It's better to make improvised tongs from wooden slats. Larger parts should be generously coated with a brush, laying them out on cardboard, each side in turn, and dry the remaining parts in the same way. Working with hot drying oil requires great care; this should be kept in mind during the impregnation process. You must not bend over a container with a boiling substance; you must wear thick work gloves.

Alternatively, the parts can be treated with antiseptics, stains, and other impregnations, of which there are a great variety in stores. They should be selected based on the intended purpose of the item: where it will be used.

At the end of the work, you can go through it with fine sandpaper again by hand, bringing it to complete smoothness.

Assembly

• It is imperative to mark the places where the cross bars are attached - these places are marked on the drawing; their location on the finished parts should be calculated based on the scale grid pitch.
• Having assembled the sides, you can begin to attach the seat and back parts. The back will be attached to the stand, the seat to the drawers.

We need to pay attention to this again. that the drawers must be fixed strictly symmetrically, and the assembled side parts, if placed on top of each other, must completely coincide, without the slightest deviation.

• Now the side parts are fastened together by crossbars; they should be attached at the legs, in the middle and at the top of the chair. For attachment, it is better to use confirmats (a type of connecting fastener);
• To attach the back and seat parts, four holes should be drilled in each block, two on each side. To ensure that the screw heads are not visible, each hole must be slightly widened from above with a drill of a larger diameter (it must be selected according to the diameter of the heads). When screwed on, the caps will end up in recesses, which can then be masked with furniture putty.

This thorough completion of the first part of the work will ensure the completion of the next one. an indispensable condition– all parts of the seat and back, all 35 bars must be positioned strictly horizontally.

Final processing

After assembly, the product must be processed again to give it a finished look. In addition, this will significantly extend its service life and maintain its aesthetic appearance.

If the parts were treated with drying oil, then after assembly the chair should be coated with oil paint, thin layers in two or three layers.

If you want the product to have the natural texture of wood, it should be treated with stain of the desired shade and varnished.

The varnish should be waterproof, just like the stain. There are varnishes that create a particularly durable coating that is resistant to abrasion and cracking. If the chair will be placed outside, it is better to take yacht varnish or something else with increased durability. In any case, it is better to keep the product under a canopy, this will extend its functionality, or at least bring it into the house during precipitation.

• For the chair you need to use strong types of wood. These are oak, larch, conifers;
• Europlywood, a 3 cm thick laminated wood material, also has sufficient strength to make the chair reliable;
• Sheets of plywood must be carefully inspected before purchasing to ensure there are no surface damage or cracks. This will eliminate difficulties when cutting the product and its subsequent processing;
• The more time is spent on processing the product and impregnating it with drying oil or compounds, the longer its service life will be;
• The chair does not need to be upholstered with foam rubber and dense fabrics, this will contribute to the accumulation of moisture under the upholstery, which will quickly render it unusable. It is better to get removable pillows for the seat and backrest;
• If ready product It leans too far back or, conversely, is oriented forward; after finishing the work, it will have to be balanced. To do this, an additional cross member is installed at the rear ends of the sidewalls. Previously, recesses are cut into it, where weights are attached according to the inclination. Also, if necessary, the front part of the chair is loaded. By adding and subtracting them, trying to sit and rock in a chair, you can achieve the ideal balance of the product.

Making a rocking chair is a rather complicated process, but quite doable. If you carry out all the steps correctly and carefully, following the drawing and tips outlined in the article, the result will be a beautiful and functional product that will last a long time.

For inspiration, you can watch the video at the link below. The video contains incredibly simple models that you can make yourself, using affordable materials.