Some basic household appliances can be made without turning to craftsmen or making expensive purchases. An original do-it-yourself shoe dryer is made from scrap materials. It is very easy to assemble. And this will not require much time and effort.

Materials and tools

The season of rain and slush brings a lot of trouble. A big problem is getting wet shoes, which are very difficult to dry at home. Putting on wet boots is uncomfortable and even dangerous to health - you can get not only fungus, but also a runny nose and acute respiratory infections. A home heating radiator is absolutely not suitable for drying shoes - shoes and boots can become deformed, especially if they are made of genuine leather or light synthetics. A quality dryer will save time and space.

In terms of tools and components, everything is quite simple. To create a shoe dryer with your own hands, you only need to use available materials, so the cost of such a product will be low, the process is not labor-intensive, and will not take much time. You will definitely need a thick wire that serves as a thermoelement, a plug, durable construction tape, and terminals. For more complex models electronic components from used office equipment will come in handy.

DIY production taking into account the model

There are many models of dryers on the market, all of them electric. However, not everyone is ready to spend money on purchasing such a device. Let's try to figure out in detail how to assemble a homemade shoe dryer at home, depending on the available materials.

Electric

The manufacturing process of this device is very simple, and almost anyone who knows a little about electrics can handle it. The basis of the electric dryer will be a thermostatic cable used in underfloor heating systems. So, to make such a shoe dryer with your own hands you will need:

• pieces of thermostatic cable;
• copper cable with a cross section of 1.5 mm (two-core);
• standard plug;
• adhesive tape;
• terminal block.

If you need to regulate the heating temperature of the dryer, you will additionally need a dimmer.

Tools that will be useful:

• screwdriver;
• pliers;
• side cutters;
• sharp knife.

Step-by-step manufacturing instructions include the following steps:

1. We make two pieces of thermal cable about 50 cm long and bend them into liners.
2. At one end of each trim we make end seal electrical tape, and on the other side we connect the block.
3. We connect both inserts in parallel copper cable With electrical plug. We wrap it several times with electrical tape.

We make sure that everything is done accurately and accurately, since the device will be connected to the mains. The electric dryer is ready.

It should be remembered that only an unplugged electric dryer can be placed in shoes. This is a basic precaution against fires and short circuits. The inside of the shoe should warm up and dry gradually.

Flexible

This method is suitable for those who have unnecessary computer parts. For work you will need:

• working cooler (can be from a video card);
• corrugated tube 1 meter long;
• box;
• power supply from the system unit 12V;
• connecting wires;
• electrical plug;
• hardware (screws).

This option is no more difficult than the previous one. To begin, take the box and make a hole in it with a diameter equal to the diameter of the cooler. Next we follow the instructions:

1. We cut the corrugated cable into two equal parts and make holes for them in the box.
2. We immerse the cooler in the electrical box and secure it with screws. The fan must be placed in such a way that air flows into the corrugated tubes.
3. All resulting gaps must be filled rubber gaskets to prevent air leakage from the device. The dryer is ready.

Both ends of the corrugation are immersed in the shoes, and the device is connected to a 220 volt network. This device can also operate from a car cigarette lighter.

Junction box with rubber elastic plugs

If necessary, trim the fan blades

Drill two holes for fasteners and glue vibration insulation to the bottom of the box and the box lid

Attach a fan

Take noise measurements

Solder the power cable to the switch. Cut holes in rubber plugs for hoses

To further reduce the noise level and create greater vacuum inside the box, seal the seam

Add soundproofing legs to the bottom of the box

From the fans

Damaging your favorite shoes by exposing them to a hot radiator is not the best idea. Radiators are not suitable for drying shoes. But if there is no special device at hand, but there are unnecessary fans from the computer, the problem is solved. The device is assembled from coolers. This electric dryer is very easy to manufacture, has low energy consumption and is small in size. To make a shoe dryer with your own hands, you will need:

• power supply 12 or 5 volts;
• computer cooler - 2 pcs.

Let's start assembling:

1. We connect two coolers in parallel to the blocks.
2. We make insulation using electrical tape. You can use heat shrink tubing.
3. The dryer is ready.

Coolers are placed either inside the boots or on top, and the device is plugged into an outlet. If you have only a 5 volt power supply on hand, for example, it is unnecessary Charger from the phone, then it can also be used. Such a device will work more quietly, but the drying time for shoes will increase due to less power.

Several fans can be connected to one such power supply at once - for example, 10, so that it is enough for the whole family for 5 pairs of shoes, respectively.

Connect two fans in parallel to the power supply

Insulate with electrical tape or heat shrink tubing

From plastic pipes

This option is perhaps the safest, since it does not require electricity to operate. The dryer can be safely used in a home where there are small children. The device is made of polypropylene or other plastic pipes and is attached to the heating radiator. This design can be assembled in 15 minutes and is quite aesthetically pleasing. appearance. So, to work you will need:

• PVC (polypropylene) pipes;
• polypropylene fittings (90 degrees);
• soldering iron

The execution process consists of the following steps:

1. We measure the width and length of the radiator. We determine how the structure will be attached to it.
2. We solder the pipes with a soldering iron, using corners and fittings to form two sides of the dryer. We fasten the fittings on two sides parallel to each other in order to place the poles in their holes.
3. We solder the central longitudinal tubes.

This shoe dryer is ready for use if the heating in the house is turned on. It can be used to dry not only shoes, but also be used for hanging clothes and towels.

Mark, cut and melt holes for installing fans

Trace the fan with a marker, melt a hole with a soldering iron, and process the edge of the hole

Mark the mounting locations for coolers, drill holes and melt a hole for the wire exit

Install coolers together with protective grilles

Prepare resistors for installation

Install resistors

Security measures

The existing scheme for manufacturing a device for drying shoes also implies compliance with certain safety rules, especially if it is an electric dryer:

1. When manufacturing an electrical appliance, it is necessary to protect your hands with rubber gloves.
2. Under no circumstances should you check for current with your fingers.
3. It is prohibited to carry out work wet hands or wet instruments.
4. Under no circumstances should children be allowed into this process.
5. Do not place the dryer plugged in on the floor. To do this, you need to use stands - metal or ceramic.
6. You can connect the finished device to the network only after immersing it in your shoes.

Drying shoes using homemade devices can be very effective. Moreover, experienced master independently creates a drying device configuration that exactly fits the dimensions of his shoes. A homemade dryer can be designed based on the location of home electrical networks and existing free space. Factory-made drying products are typical and do not take into account either the load on the network or the convenience of placement.

Repair homemade device drying shoes is also elementary. According to the scheme, it is no more complicated than an old iron. It is enough to have basic knowledge of electrical engineering and take basic safety precautions.

Protect your hands with rubber gloves

After a long walk in the rain or sleet, shoes need to be thoroughly dried. Many people simply place their boots on the radiator and leave them to dry. But such drying will not bring anything good. The fact is that extreme heat causes shoes to warp, and often the soles begin to peel off. This is why wet boots need to be dried properly.

In this article we will tell you a few interesting options How to make a shoe dryer with your own hands.

To make this version of the dryer we will need slats. You can use them to make a grille that will be installed on the battery. In this case, the shoes will not come into contact with the radiator, so they will dry evenly.

Materials and tools

We will need the following materials.

• The slats are 0.5 cm thick.
• Carnations.
• Soft synthetic material.

The tools you will need to prepare are:

• hammer;
• sandpaper (with a special lock for ease of use);
• electric jigsaw;
• construction stapler.

Completing of the work

• First of all, make a small diagram of a homemade dryer.
• After this, cut the main bottom rail to the required length.
• Next, nail the side walls of the grille onto nails, only then install and nail the internal dividers.
• When the overall frame of the dryer has already been made, you need to work on the back wall. You don’t need to nail the slats too tightly; you need to leave about 1 cm between them..
• At this stage you need to staple it to back wall dryers synthetic soft material. This is necessary so that the radiator is not damaged when installing the structure.
• At the end of the work, small wooden hooks are created from slats for fastening to the radiator.

Important! Before installing a homemade dryer, make sure the radiator is securely fastened. If the fastening is weak, then the radiator may sag under the weight of the grille and shoes. This may damage the pipeline.

How to make a heating dryer

This method is considered the most effective. But it requires a little more time to manufacture compared to the previous version.

Materials and tools

For production we will need the following.

• Polypropylene pipes.
• Polypropylene fittings.
• 2 ball valves.
• 7 steel pipes 1 m long.

We also need the following tools.

• Pipe cutter
• Soldering iron for pipes.

Manufacturing process

• Solder a small piece polypropylene pipe then install a tap into the heating system and turn it off.
• Then run the pipe to the location of the future dryer.
• In the same way, you need to do it in the heating area after 2 m. Solder a piece of pipe through the fitting, and then install a closed tap. After that a pipeline is created to the intended location of the dryer.
• Now we need to create the outline itself, which will dry the shoes. To do this you need to use polypropylene fittings. They need to be soldered into steel pipes. You need to create a closed loop. The elements must be parallel to each other. The distance between them should be approximately 5 cm.
• When the heated circuit is created, it will be possible to solder it with the pipes that we connected to the heating system.

The huge advantage of this dryer is that it can be turned off and on as needed. To do this, we installed taps.

Therefore, you need to install a wooden grate or dense synthetic material on the pipes. In this case, there will be no close contact and no damage will be caused to the boots.

How to make electric dryers

Materials and tools

To create an electric dryer we will need the following.

• 2 computer coolers.
• 12 volt power supply.
• On/off button
• Cardboard box.
• Wires.
• Pencils for glue gun.
• Corrugated pipe 2 m.
• Scotch.
• Sewer plastic couplings.

We also need such tools.

• Jigsaw.
• Glue gun.
• Scissors.

Manufacturing

Now our dryer is ready for use! The power supply needs to be plugged into the outlet, then install the pipes in the shoes and turn on the power button. Air will be forced into the box and blown out of the pipes, thereby quickly drying wet shoes.

From our article you learned different ways making dryers with your own hands. We wish you success in production!

During the off-season, many of us are faced with the problem of constantly getting our shoes wet, because knee-deep puddles and slush are quite common in our latitudes. Often, even the highest quality shoes cannot withstand this kind of load and, over time, begin to leak moisture in certain places. Therefore, when we come home with wet shoes, we think about how to quickly dry them, because no one wants to put cold, wet shoes on their feet again in the morning. Solving this problem is not difficult - you can buy special device in the store or learn how to make a shoe dryer with your own hands without spending a lot of time and money on it. In this article we will look in detail at how to bring such an idea to life. Several master classes on making shoe dryers at home await you. Let's get started.

Is it worth focusing so much attention on the problem?

• Wet shoes are a source of fungal development, which is then very difficult to get rid of.
• In addition, if you wear wet sneakers or shoes, a person will inevitably suffer from a runny nose or cold.

Important! The easiest way is to try drying your shoes on a radiator using a wooden or plastic grate, on top of which you place damp shoes or boots. In this case, the hot radiator will not come into contact with the material of the sole, which means it will not harm it. Natural circulation heated air allows you to dry your shoes in just a few hours.

How to make a battery-powered shoe dryer with your own hands?

This is the safest, most effective and inexpensive way solutions to the problem of wet feet. You can make a shoe dryer for a battery with your own hands quite quickly. We will make it from the remains of the laminate, and such a design will have a large number of pros:

• You can attach it to the battery itself on the side.
• You can simultaneously install several of these homemade dryers on one radiator.
• It will be easy to disassemble, for example, in the summer you can hide it so that it does not take up extra space.

Materials for work

To work you will need the following materials and tools:

• Remains of unused laminate 8 mm thick.
• Pencil and ruler.
• Electric jigsaw.
• File and sandpaper.
• Electric drill with a drill bit with a diameter of 8 mm.
• Paint or varnish, brush.

Construction device

Such a dryer will consist of the following elements:

• Two rack holders.
• Internal locking plate.
• External locking plate.
• Screen stop.
• Two wedges.

Important! To simplify assembly, we will supplement the design with an auxiliary strip. By the way, since the support stand is the most important element in such a design and has a complex configuration, you must strictly adhere to the dimensions indicated in the drawing.

We will assemble the dryer without using glue.

And now we will learn how to make a shoe dryer that will be attached to the battery:

1. At the first stage, we need to make special holes for cross-shaped joints (linings in the wood floor). Making them is very simple: you first need to mark the sample in the right place, then drill a hole in the middle with a diameter of 8 mm, according to the thickness of the laminate. Next, cut out the sample with a jigsaw along the inside.
2. Since cuts can swell and destroy the structure when exposed to moisture, each cut must be varnished or painted over.
3. Now we connect the racks with the auxiliary strip. Holding the bar with one hand, you need to push the lower parts of the racks into the first and fourth openings between the radiator sections. And with the second hand we install the internal locking bar, threading it through the central section.
4. Then you need to slightly tighten the auxiliary bar and install the outer locking bar on top.
5. While the dryer is in free movement, it is necessary to determine a specific place for it, then install wedges.
6. Next, you can remove the auxiliary bar and insert the stop screen.
7. As a result, you will have a space between the battery and the screen, where, in fact, the shoes will be inserted with their toes down.

Making an unusual universal shoe dryer with your own hands

In this section we will learn how to make a shoe dryer with your own hands from an ordinary computer fan.

Materials

You need to prepare the following elements for work:

• Unnecessary working fan (cooler).
• Meter corrugated tube.
• 12 volt power supply.
• Electrical wires for extension and connection.
• Electrical box.
• Screws.
• Electrical plug.

Master class on getting the job done

The assembly of our dryer looks like this:

1. Cut through the box round hole so that the cooler fits in it.
2. Divide the corrugation into two equal parts, make slits in the box for them.
3. Insert the cooler, secure with self-tapping screws so that air enters the attached hoses.
4. Seal all cracks and gaps with rubber gaskets, which will ensure right direction air flow. Now the dryer is ready.
5. Now insert both ends of the corrugation into the boots and plug the device into a power outlet to test it.

After walking in the rain or in wet snow, boots and boots need to be dried. Usually shoes are placed on top or leaned against a hot heating radiator. The consequences are quite predictable: after several procedures the sole peels off or the skin warps. The shoes are completely ruined, and so is the mood. Fortunately, it's not all bad.

How to deal with the problem?

Wet shoes can cause fungus to develop. If you wear wet shoes, you will inevitably get a cold or runny nose.

The most in a simple way avoiding such troubles is installed dryer to the battery. This is a removable plastic or wooden grate, on which damp boots or sneakers are placed on top. A hot radiator, without being in direct contact with the sole material, cannot cause harm. Natural circulation of heated air promotes high-quality drying in a few hours.

Ionic, electric, ultrasonic, antifungal and others

To understand the devices presented on the market, we list some of their features.

1. A floor-mounted electric shoe dryer can accommodate several pairs of boots or shoes at the same time. This is not the smallest structure that takes up a certain place in the hallway.
2. Among the mini-options designed for one pair, there are those equipped with a fan, ultrasonic, and ultraviolet.
3. Flexible universal electric shoe dryer has an insulated inside a heating element, which is inserted inside the shoe.
4. Induction mats that take up little space and are completely safe.

The choice of a specific design depends on the number of family members, the size of the hallway and the preferences of the owners. In some cases, you can make quite decent and convenient device for this purpose.

Unusual universal homemade shoe dryer

Why ruin your favorite boots? hot battery, when you can make a completely decent device from a computer fan. To work you will need the following elements:

• unnecessary working cooler;
• meter corrugated tube;
• 12-volt power supply from the computer;
• extension and connecting electrical wires;
• electrical box;
• several screws;
• electric plug.

Before assembly, you need to cut a round hole in the box to the size of the cooler. We divide the corrugation into two parts and also make slots for them in the electrical box. The cooler must be inserted and secured with screws so that air is forced into the attached hoses. All gaps must be sealed with rubber gaskets to direct air flow in the desired direction. It turned out to be a shoe dryer. With your own hands, both ends of the corrugation are inserted into the boots, and power is supplied to the device. This original design It can even work from a car cigarette lighter, which is very important for country trips, in the country, fishing or hunting.

Non-standard use of familiar objects

In the warm season, sneakers and sneakers can simply be hung by their laces on a clothesline. Sometimes they are secured with clothespins. The breeze helps the moisture to evaporate. In an apartment you have to use home appliances. In urgent cases, even blowing with a hairdryer helps.

The dryer can be made from a conventional “wind blower” - a home heater with a fan. The wet couple is placed on a low stool. Shoes blown with hot air are driven into normal condition in 2-3 hours. It is strictly not recommended to leave the heater turned on for a long time (at night) without supervision - in order to avoid a sudden short circuit.

Lumps of crumpled newspaper sheets placed inside boots quickly absorb moisture. The inconvenience is the need to regularly (every hour and a half) replace dampened paper. If you combine these two methods: pieces of newspaper and blowing with a wind blower, the result will be achieved much faster.

Apartment stove-heater - shoe dryer

With your own hands you can create something completely original and useful device for the designated purpose. You will need to stock up on medium-sized river pebbles in advance. Then it gets ready wooden frame- a frame with low walls that looks like the bottom will be an oil heater laid on its side. From below it is installed on a frame with legs, and prepared stones are laid out on top of it.

This device can always be kept on, as it has a temperature regulator. Wet shoes are placed on heated pebbles and kept until completely dry.

The size of the structure depends on the dimensions of the radiator. The shoe dryer is made by yourself and you can use it. It can accommodate several pairs that are not in danger of overheating or drying out.

We assemble a device for drying shoes - an electric dryer from a self-regulating thermal cable. Electric drying for shoes can make the autumn-winter slushy period much more comfortable. In addition, dry shoes are a matter of maintaining health, so this is far from a useless device.

Materials and tools

Materials:

Cuttings of thermal cable (can be from a "warm floor" system);

Copper two-core cable with a cross section of 1.5 sq. mm;

Electrical plug;

Dimmer (you can do without it if you don’t need to regulate the heating of the dryers);

Insulating tape;

Terminal block.

Tools:

Pliers;

Screwdriver;

Knife and side cutters.

Making a dryer

So, from scraps of thermal cable 35-50 cm long we make two insert loops.

On two sections of cable we make an end seal on one side (see photo) and connect the terminal block on the other side. You can make not a terminal connection of wires, but soldering.

We connect two “loops” with a cable and a plug in parallel. Additionally, we insulate it with several layers of electrical tape or cover it with a thermal tube.

We do everything carefully and reliably, because we will connect the dryer to a 220 volt network - there should be no mistakes!

Demonstration of heating a homemade shoe dryer with an infrared non-contact thermometer.

Important! We place the thermal cable in the shoes to dry and remove it only when the power is turned off!

It is IMPOSSIBLE to ignore the safety rules