Every user of plastic products, after a long period of operation, faces a dilemma - how to adjust a plastic door? Whatever high performance The door and its components, which are designed to ensure the closing and opening of the PVC door, did not possess the quality; after a certain time, the mechanism, one way or another, will need adjustment.

If it is necessary to regulate a PVC door, it would be more rational to contact the appropriate specialists, in particular those who installed it. But, unfortunately, such an opportunity is not always available, and it is unlikely that the technician will be dispatched on the day of the call.

In addition, mastering the skill yourself is not at all difficult, since the process of adjusting a plastic door is not something supernatural. Moreover, customizing plastic products is never a frequent procedure. Adjusting a plastic door is only relevant if you have a complaint about the functioning of the door.

The installation of a new plastic door also includes adjustment work, which is carried out immediately, and for a long time afterwards, the design should not raise unnecessary questions. But after a period of active use, the product will still need to adjust the mechanism, as a result of sagging, poor clamping or the inability to close the door.

Despite the excellent quality and confidence in the organization that installs the door, it is recommended to personally observe the adjustment process to make sure that the adjustment of the plastic doors was carried out correctly.

Upon completion of work related to the establishment of hinges of a plastic structure, pay attention to the following points:

• the frame should be pressed tightly against the box around the perimeter;
• opening and closing the door should be easy, without additional effort, without squeaks;
• use building level to check the verticality of the door;
• check the random opening and closing of the sash. To do this, you need to open the door halfway, and when checking, exclude the influence of wind and draft.

Frequent damage to plastic doors

The most popular defects in product operation are:

• The bottom edge of the sash touches a part of the frame that functions as a threshold. This occurs as a result of the sash sliding under the influence of its weight;
• The canvas touches the middle of the frame. The reason for this is the direct movement of the sash under the influence of various deformations, as well as temperature;
• Poor pressing of the sash to the frame, as a result of wear of the seal;
• Staggering and falling out of the door handle socket.

Initially, it may seem that adjusting a plastic door is a complicated procedure based on the options for possible malfunctions. But in fact, you just need to understand which mechanism needs adjustment, and the instructions below will help you troubleshoot problems with your own plastic product.

Adjustment of plastic structure

Before you start installing a PVC door with your own hands, stock up on screwdrivers (regular, flat and Phillips), hex keys of different sizes, and spacers.

Competent instructions and necessary tools will allow you to correctly perform the entire cycle with your own hands, and as a result, the adjustment of plastic doors will be carried out successfully and safely.

Eliminating sash sagging

To eliminate such a breakdown, you should point the blade upward and slightly move it towards the loop, which is located above. Open the sash, and using a hex key (4 mm), turn the screw on the end of the sash at the top, at the location of the hinges.

To move the sash, make about 1-2 turns in a clockwise direction. After this, close the sash and remove the protective cap from the hinges located below. Turn the screw on the top hinges, slightly lifting the blade. If the sash moves easily, then the problem is solved.

Pressure adjustment

Schemes for adjusting hinges on a plastic door.

To adjust the pressure of the canvas to the frame, it is necessary to use a locking element. It is located inside the sash and acts as eccentrics. The trunnions are adjusted with a special key and pliers.

Do-it-yourself pressure adjustment is done in summer and winter periods, this is sufficient for normal operation of the product. In winter, you should independently adjust the pressure tighter and stronger than in summer. It is necessary to press the sash to the frame from the hinge side using adjusting screws.

Horizontal adjustment

Correction of the operation of hinges of a plastic structure can be done in both vertical and horizontal directions. In order to horizontal adjustment, first remove the door from the hinges located at the top.

Then close it and lift the caps that hide the adjustment screws. To avoid warping the product, tighten the long screw at the top hinges slightly with more force than at the bottom. To ensure uniform movement of the sash, remove the trim from the hinges and tighten it by loosening the horizontal screws located in the door hinges.

Vertical loop adjustment

If it is necessary to raise or lower the product, adjust the mechanism vertically. There is an adjusting screw along the axis of the lower hinge. To adjust the entrance plastic doors, a hex screwdriver (5 mm) is useful.

By turning the tool, the door can be raised slightly, and if the screwdriver is rotated reverse side– the structure will be lowered.

How to avoid frequent adjustments?

It will not be possible to completely get rid of door adjustments, but making it less frequent is quite possible. When purchasing a double-glazed window, make sure that the fittings match the weight of the panel.

The optimal weight of the sash is considered to be 100-130 kilograms.

Sagging of the structure under its own weight can be eliminated by installing an auxiliary element of the fittings, which is called a sagging compensator, better known as a “microlift”.

Such a detail is simply necessary for the product, especially if there is a double-glazed window with impressive dimensions of the structure. And if you correctly install the support rail - the opening limiter - with your own hands, you can easily avoid jamming and sagging of the structure.

As you can see, adjusting a plastic door is not very difficult if you wish.

Today, the choice of apartment and house owners often falls on a plastic door. It is used as an entrance, interior or balcony. In any of these options, the plastic design looks interesting, attracts attention and guarantees good performance characteristics. However, in winter time plastic doors require special care - it is necessary to transfer them to winter mode.

Attention! You can change the door operation for winter yourself. The owners are wondering how to adjust the sash so that it retains heat in the room and eliminates drafts. Adjustment is easy, but it is recommended to first know what winter and summer mode are.

Arrangement of fittings on a PVC door leaf

Characteristics of plastic structures and methods for opening them

Home renovation involves not only replacing floors, ceilings, or dismantling partitions, but also installing new windows and doors. This is a responsible and difficult step, but it is necessary. Residents of our country purchase plastic windows, which manufacturers give different sizes and characteristics. But the main function plastic windows and the door to the balcony is to give the room as much beauty, warmth and light as possible.

During the renovation process, due attention must be paid to the installation of plastic windows. Let us note that their price is acceptable for every person, and their performance capabilities are high. For plastic windows and doors different ways opening. There are designs in which the sash is rotating; such models are the most common. There are also windows with a folding sash; they are convenient to use when ventilating rooms. Models of windows and doors with a tilt-and-turn opening method are also available, and such windows are easy to clean.

The only one important nuance During the renovation period, proper installation and adjustment of all elements of plastic windows becomes necessary. Only professionals who install these structures can perform such work. Therefore, do not skimp on paying employees, since windows are installed once and for a long time, and everything should be on time. top level.

Adjustment and correct setting of fittings

Useful information about PVC doors

It is recommended to purchase plastic doors exclusively from trusted companies. Only brands that have proven themselves on the market guarantee a long service life of the device. It is preferable to entrust the installation work to professionals. However, if you have the skills and relevant knowledge, you can do the installation yourself. The initial adjustment of the structure is also important.

Even at the door acceptance stage, take a closer look at certain indicators. Pay attention to the material, fittings, including locks and handles. Each element requires professional adjustment. In particular, attention is paid to the following:

1. Normal closing and opening of doors. There shouldn't be any difficulties. To check the vertical and horizontal installation, use a building level.
2. Pressing the leaf tightly against the door frame. It should be dense and uniform around the entire perimeter.
3. Arbitrary opening or closing of the door must be completely prevented.

Adjustment process PVC sheets in case of failures in its initial setup

If everything is in order, it means the door is of high quality and you can enjoy its use. Of course, do not forget that the door needs adjustment from time to time. Twice a year it is switched to winter or summer mode.

Read also: - debugging rules and expert advice

When is door adjustment needed?

Often people notice a problem when it is already running: drafts arise, the door does not close or open well. These are already problems that were the result of previously unnoticed situations. In fact, you can see all the shortcomings of operation at the initial stage. It's much easier to fix the problem here.

There are many in various ways see the shortcomings of the door. One of the simplest helps to determine the weakening of the pressure of the canvas to the box. For this you will need a sheet of paper. It is clamped between the frame and the door frame. After this, they carefully pull the sheet and, if this is done with difficulty, then everything is in order with the door pressing. This check should be performed along the entire perimeter of the structure. If malfunctions are noted, they will have to be corrected. Using available tools, the pressure is maximized.

The problem may also be subsidence of the canvas. The door in the closed position is circled around the perimeter. Pencil lines should match the edges door frame V open position doors If deviations are detected, you will have to adjust the position of the sash.

Useful tips on setting up metal-plastic sheets

Horizontal adjustment: operating algorithm

Horizontal adjustment is required when the door sags due to its own gravity. A typical manifestation may be the handle sticking when the mechanism's crossbars do not fit into the grooves intended for them. As a result, the structure is difficult to open and drafts occur. The following algorithm will help to cope with the problem, switching the door to winter mode:

1. Open the door.
2. Remove the screws from the top hinges.
3. Close the sash.
4. Remove the covers and unscrew the long horizontal screw.
5. Inspect the screw for damage. If they are missing, screw it back in, tightening it more at the top loop.
6. Remove the trim from the bottom hinges.
7. Adjust the operation of the lower hinges by tightening or loosening them to ensure even movement of the sash.

Basic options for adjusting metal-plastic sheets

Vertical door adjustment and pressure adjustment

The door structure may also need to be adjusted and adjusted vertically. Here questions arise about how to adjust the sash in order to switch the product to winter mode. To do this, find a screw, which is called an adjusting screw. It is usually located at the bottom end of each loop. To adjust it, use a traditional hexagon of suitable size. Depending on the direction in which the screw rotates, the sash will lower or rise. Clockwise movement promotes lifting, counterclockwise movement promotes lowering.

Read also: - stages of work, materials and tools

Additionally, the clamping force is adjusted using a locking pin, which is available on any blade. There is an indicator notch on it, which can be loosened or tightened depending on the need.

Attention! The adjustment screw is often hidden behind a plug. This is important to consider when trying to adjust the design.

Appearance PVC entrance door

Now you know how to independently configure your doors for winter operation. The configured version of the design is easy to subsequently adjust, the handle works properly, and the product itself easily opens and closes without letting in the cold. If you do not fully understand how to switch plastic doors to winter mode, check out the video presented. It will accurately and clearly illustrate how to translate plastic products in “winter” or “summer” mode. After watching the video, switching the door to winter mode will be easy for you.

In contact with

Comments

Unfortunately, there are no comments or reviews yet, but you can leave your...

New articles

New comments

Vladimir

Grade

plank1957

Grade

Novel

Grade

Irina

Grade

Yaroslav

Grade

Latest reviews

adminadmin

One of the nuances of caring for plastic doors is their adjustment. In our article we will familiarize ourselves with the need to carry out such procedures for balconies, as well as entrance doors, we will find out how horizontal and vertical adjustment is carried out, changing the clamping force door leaf, Special attention Let's replace the gaskets.

In what cases is adjustment needed?

Modern entrance groups made of plastic, as well as balcony doors made of similar material They differ from similar products in their durable coating and high-quality fit of individual parts. Thanks to these properties, the described structures can serve their owner for decades without the need for maintenance. repair work.

In some cases, the user may have a problem with adjusting the balcony door. This is especially scary for the home owner when the product fails guarantee period. Despite the fact that many call a specialist, you can adjust the plastic door yourself.

Before carrying out the main work, you need to find a malfunction in the design of the frame or canvas and eliminate it by tightening special threaded connections. In the majority of cases new door the balcony does not require additional regulation. This is due to the fact that the products received from warehouses are made of wear-resistant materials, their main parts are fitted very carefully.

Despite this, situations arise when a plastic entrance or balcony door needs immediate adjustment. If this is not done on time, then the owner of the house will have to completely replace the entire structure, and these are additional unforeseen expenses. According to experts, the regulatory process should be performed once a year at most.

With more frequent repair work, the product can quickly become unusable. This is due to wear of the seals, microlifts, as well as adjusting screws or plastic frame.

The need to regulate balcony doors arises in the following situations:

• Sagging of the balcony sash when the leaf begins to rest against the threshold. As a result of friction of parts, wear occurs not only on the sash, but also on the threshold itself. Repair work must be carried out when the first signs of sagging appear.
• The lock does not click well or the blade is pressed tightly. In this case, it is necessary to adjust the pressure of the plastic doors. To do this, you need to adjust their location in the frame structure.
• At the junction of the frame and the canvas, a gap is formed through which cold air penetrates into the apartment. In this situation, the sash is adjusted using microlifts that are installed in the hinges. Loose pressing of the canvas to the frame reduces the energy efficiency of plastic windows or entrance groups.
• The doors cannot be closed. The reason for this phenomenon is considered to be the occurrence of distortions, which usually lead to deformation and fracture of the hinges, destruction of the seal structure or other problems. In this regard, before carrying out repair work, it is necessary to determine the location of the breakdown.

The need to adjust the entrance groups arises when sealing is lost. If there is a draft in the room, then gaps have appeared between the frame and the door leaf that need to be eliminated urgently. In some cases, to determine a breakdown, it is enough to run a pencil along the frame, after which you can see the discrepancies in the parallelism of the lines. The presence of distortions or free gaps can be determined in another way. You need to put a sheet of paper between the canvas and the frame and slam the door. Now try to pull out the leaf. If this element comes out problematically (with some effort), then there are no problems with the doors; if it is loose, then the apartment owner must adjust the door pressure himself.

Horizontal adjustment

Adjusting plastic doors is not a complicated process, but it does require attention to detail. Before you begin the main work, you need to prepare the following tool:

• set of hex keys;
• construction tape;
• screwdrivers (flat and Phillips);
• plastic gasket;
• Manufacturer's instructions for adjusting door structures.

For work on adjusting the door leaf in horizontal plane Usually special screws are used that rotate in the required direction using a hexagon. These elements are usually located under the holes above the top and bottom hinges.

To adjust the correct position of the product, you need to open the blade slightly and get to the screws. By turning the fasteners in the desired direction (clockwise or counterclockwise), the correct position of the door is achieved.

If the screws are rotated clockwise, the surface of the product will slowly move towards the canopy, in the second case - away from it. Using a similar method, you can eliminate a gap or displacement of elements up to 2 millimeters. The different intensity of regulation of the upper and lower canopy allows you to adjust the required vertical deflection of the canvas. In some door models, the canopies are disguised. To get to them, press the tab on the end of the product and set the handle to the ventilation function. Once corrected, the door should close and open correctly.

Vertical adjustment

The need for vertical adjustment arises when the sash rests on the threshold or when there are dents on the upper or lower seal. A special screw is used to adjust the hinges. Rotation of this element in the required direction leads to the raising or lowering of the door, which will allow for a normal gap.

Before starting the main work, remove the plug from the screw for adjustment. Typically, such an element is located on the lower hinge, its working part is located along the axis. The screw rotates using a hexagon. To lift the blade up, you need to rotate the screw clockwise; to move down, the adjuster is rotated in the opposite direction.

How to adjust the door pressure

The front door's clamping force should be adjusted only after such a problem has been identified. This can be checked using a flat piece of paper from a notebook; it is applied to the frame and the door is closed. If the leaf is pulled freely from the slot or with little effort, then it is necessary to adjust the loops. To localize the existing problem, the specified work is carried out along the entire perimeter of the frame.

While pressing the sash against the frame, it is also necessary to determine and evaluate possible distortions of the interlocking structural elements. To do this, close the door and carefully trace its contours with a mechanical pencil. After opening the canvas, evaluate the size of the contour gap relative to the frame.

In most cases, the pressure of the door leaf is adjusted using a pin located at the end of the door. This element must be rotated with extreme caution, since a small movement causes a significant clamping force, which can lead to destruction of the seal structure. In the case when the trunnion is installed perpendicular to the profile, the clamping force will be set to the maximum, when installed in parallel - to the minimum. If the adjustment part has reached its maximum position and it is not possible to provide the required clearance, the apartment owner should seek help from specialists.

Some sources have information on how to adjust the clamp in another way. The fact is that in some models of plastic doors there are two or three eccentric screws at the end of the door leaf, the rotation of which leads to a change in the clamping force. Each of these products has a special mark to determine the clamping density. To weaken the clamping force, turn the screw towards the frame; to strengthen it, turn it towards the room.

Difficulties mainly arise when there are three eccentrics (upper, lower and central parts designs). In this case, you need to act experimentally, deflecting the eccentrics to the same angle. After each of these adjustments, the result obtained is checked. High-quality clamping can only be ensured near the handle fastening, so in other places (upper and lower parts of the door) adjustment of the hinges may be necessary.

Replacing rubber seals

Seals installed on door designs made of PVC, protect the apartment from noise coming from the street and drafts. Over time (especially in the absence of a closer), these products may become flattened or cracked, and in these cases their replacement is necessary. Let us immediately note that the rubber bands can be changed independently without using a special tool.

At the initial stage of work it is necessary to go to hardware store and buy insulation. It is made in the form of a rubber band a certain form. In this case, it is necessary to purchase a product specifically for doors (there are seals for sashes and frames of plastic windows).

First you need to remove the old seal; you simply touch it with a sharp object and pull it out of the groove. Now clean the recess from dust and dirt, insert one end of the elastic band and completely recess it into the groove. We go around the entire perimeter in a similar way until the material is completely laid. Next, we trim the rubber and check the tightness of opening and closing the door.

Reading time ≈ 4 minutes

Long-term use of plastic balcony door leads to imbalance of its mechanisms. As a result, the door closes poorly or stops closing altogether. You can correct the situation by contacting the company that installed it. However, it is not always possible for a specialist to come to you after an application; as a rule, you have to wait several days. If time is pressing, you can do the work yourself. After all, adjusting a plastic balcony door does not cause much difficulty.

The balcony door can be adjusted in several directions:

• vertically;
• horizontally;
• sash pressure adjustment.

Vertical adjustment

To eliminate the sagging that prevents the door from tilting and causes the threshold to touch when opening or closing, you need to adjust the sash in height, that is, move it up. Work is carried out with the lower loop.

1. First, release the loop itself from the cap.
2. Insert a screwdriver into the hole in the upper end of the hinge and turn the adjusting screw clockwise to raise the door. If it needs to be lowered, then the rotation is made counterclockwise. Usually 2-3 turns are enough. In the video you can see how to do it correctly.

If such adjustment of plastic balcony doors is carried out independently, then after each stage it is necessary to carry out a check to make sure that everything was done correctly. The shutter should move freely, there should be no problems when opening, and when closing it should close without interference, but tightly.

We must remember that not all PVC windows and doors have hexagonal adjustment holes. Sometimes you need to use a key - an asterisk, you can see what it looks like in the photo. It is advisable to purchase such a key in advance, and if you need to adjust the plastic balcony doors yourself, it can be done using this device.

Horizontal adjustment

When temperature fluctuates, deformations may occur that prevent the balcony door from closing. The sash simply rests against the mechanism and does not go further. Using mechanical pressure she can close the door. But the use of force when opening or closing doors is undesirable, as this provokes further deformation.

To eliminate this problem, the plastic balcony door, namely its hinges, is adjusted. To adjust, you will need an H4 hexagon.

1. The end of the screwdriver is inserted into the side adjustment screw, which is accessible from the lower side surface of the lower hinge.
2. They begin to tighten the screw to tighten the sash to the hinge.

So the sash can be shifted to the right - to the left by a distance of up to 1 cm. If this is not enough, then you need to repeat all the steps with the top hinge. If the adjustment of the PVC balcony door is carried out correctly, the sash will close freely, without interference.

Adjusting the pressure of the balcony door

So that the sash does not let through cold air from the street, the pressure of the balcony door is adjusted. For this they use locking elements, available on the sash. Usually they are made in quantities of 4 pieces. Almost always, the adjusting clamping screws are made as eccentrics, that is, the hole for the hexagon has some offset from the center and its rotation allows for displacement in both directions, obtaining optimal level pressing. By turning such an eccentric, you can either strengthen the pressure or weaken it.

Sometimes the clamping screws have a different design. If the screws go through a special hole, then in the central position the pressure will be minimal. Moving around the axis will lead to a change in the level of pressure. Therefore, in order not to make a mistake with the method of adjusting the pressure, before starting work, you need to familiarize yourself with the hardware features of the door that is installed on your window manufacturer’s website.

To check whether the adjustment has been carried out correctly, you need to close the door by inserting under top part sash sheet of thick paper or banknote. The correct level of pressure is indicated by the tightness of the bill being clamped by the flap; it should be held in the place where it was clamped and pulled out only after applying some effort. Using this simple technique, you should check the entire perimeter. If the paper holds well everywhere, it means everything was done correctly, and winter winds and drafts are not a problem.

Adjustment of plastic doors should be carried out approximately once a year. Timely correction of the position of the sash in the opening will help avoid its irreversible deformation and extend the service life of the entire structure.

Video of adjusting a plastic balcony door

Today, many, in search of comfort and warmth for their home, prefer to replace wooden windows and the doors are made of plastic. Such designs have many advantages, but there is also a certain feature: after some time, PVC products require adjustment. If you feel that doors or windows are closing less tightly or require serious effort, then it’s time. If the warranty period has not yet expired, the easiest way is to call a specialist who will do everything quickly and free of charge. Otherwise, there is no need to panic either: adjusting plastic windows and doors yourself is a completely feasible task.

When is adjustment required?

An important point: windows and PVC doors have a similar mechanism (except that the former allow one more degree of opening), so in the future all instructions will be given using the example of windows. In the case of balcony doors, the work is carried out identically.

You can understand that urgent and immediate adjustment is required by the following signs:

• the window sash clings to the frame;
• opening and closing involves significant effort;
• handles are loose or too tight to turn;
• windows let in outside air even when closed.

If the window opens or closes poorly, it means that its mechanisms need to be adjusted

The mentioned signs show that the window is in extremely poor condition, so it is possible that some parts may require serious repairs or replacement. To avoid such an outcome, you can take preventive measures.

You can determine whether they are needed as follows:

1. Open the door or window slightly. If, in the absence of a draft, the sashes close or open on their own, it means repairs and adjustments are required.
2. Outline the entire shutter when closed, and then open it. Compare the lines and edges of the window opening. Ideally they should be parallel. It is recommended to eliminate even the slightest distortion.
3. Take a piece of paper or newspaper. Then slam the window so that the sheet is between the sash and the frame. Now, if you can pull it out without effort, then a little adjustment will be required. Ideally, the effort to remove paper should be the same, no matter where the sheet is located.

Adjusting the modes according to the season allows you to customize the operation of window mechanisms in the most in the best possible way

Finally, the adjustment of plastic windows is carried out in the off-season: by winter they try to strengthen the pressure, by summer - to loosen it. This adjustment helps to avoid rapid wear of individual parts of the closing mechanism..

Tools and basic adjustment mechanisms

For work you will need to prepare the following tool in advance:

• pliers;
• Screwdriver Set;
• PVC gaskets;
• a set of hex and star keys;
• roulette.

The main bolts used to adjust windows and doors are shown in the figure. To access some, you will need to remove decorative plugs.

Handle adjustment

First, let's look at the malfunctions associated with the handle (window or door - there is no fundamental difference here), and ways to eliminate them.

Repairing a loose handle is one of the simplest. There is a special decorative plug under the handle. It is enough to pull it towards you a little and turn it a quarter turn. This should be done by hand, otherwise the material may be scratched. Under the plug there are a couple of bolts that need to be tightened a little.

The bolts securing the handle are located under the decorative plug

Produced in a similar way complete replacement handles: unscrew the bolts under the plug, carefully remove the handle and insert a working one in its place. All that remains is to screw the fasteners.

Most often, the problem of a sticking handle is solved by simply lubricating the mechanism.. It is done as follows: first, the handle is removed, after which the mechanism is cleaned with a vacuum cleaner. All that remains is to lubricate it. The best option There will be a can of WD-40 liquid with a convenient tube that will help you reach all the difficult places.

If the handle turns noticeably tight, the clamping mechanism should be adjusted. For this purpose, there are special pins at the end. In details this adjustment plastic windows and doors will be described below.

Adjusting the downforce of windows and doors

Rubber used as insulation and sealing can lose volume over time. As a result, cracks form, due to which not only heat suffers, but also sound insulation. A similar problem arises due to deformation caused by temperature changes in winter and summer. Often, the solution is to change the seal, but in fact, the design of the hardware itself allows you to eliminate the gaps without any replacements.

The key elements are small cylinders that are located on the side of the window or balcony door in the slots of the plugs. They are called trunnions or eccentrics. Directly opposite them in the frame is a mechanism to which they engage. To adjust the pressing force, you need to adjust either the trunnions or the clamping mechanism - it all depends on the model of the fittings.

Trunnions or eccentrics are responsible for the degree of pressing of the sash to the frame and may vary depending on the manufacturer

To prevent the sash from being pressed so hard, the oblong part of the eccentric rotates to the side outer surface, for strengthening - towards the inner side. The adjustment method varies depending on the hardware manufacturer, but the principle is general: the trunnion has a special slot for a key or screwdriver. In some cases, to turn, you will need to pull the trunnions slightly towards you using pliers. You must act with extreme caution - there is a risk of damage to the mechanism.

In some cases, the cylinders themselves cannot be adjusted - in this case, all that remains is to adjust the position of the mating part. In such fittings it is secured with a pair of bolts. It is necessary to loosen them a little and then move the hook in the desired direction.

Adjusting awnings

The following applies exclusively to windows with a transom system (it is this that helps to open the window slightly for a little ventilation). On the door similar system Most often it is not installed.

Before you begin setting up, you will need to remove decorative casing on the mount. There are several bolts on the mount itself - they are used to set the position of the sash in relation to the frame. First, you should pay attention to the bolt that is located perpendicular to the plane of the glass unit. The design is adjusted when the windows are closed. Adjustment is made with a hex key - it rotates left and right to achieve desired location.

Adjustment of the upper canopies is carried out by tightening the bolts from the scissor system

To fasten the upper part of this design, not ordinary hinges are used, but a special system known as “scissors”. Those wishing to access the adjustment bolts will need to open the window. Next you will have to act almost by touch. On the side surface, at an angle to the insulation, there is a clip that plays the role of a blocker. After pressing (the clip springs slightly), you need to set the sash to ventilation mode. If everything is done correctly, it will hang on the “scissors” and the lower canopy. All that remains is to adjust the pressure with the bolt (its location is easiest to assess from the photo). The adjustment process is exactly the same as for trunnions.

The edge of the window or door sash touches the frame

A similar problem can be encountered if the windows are often open: the fastening of some fittings becomes loose or they themselves become deformed. Critical damage cannot occur, and the problem is solved by adjusting the position. The easiest way is to look at the manufacturer’s logo on the fittings and find detailed guide on the official site. However, there are a number of general rules:

1. If the sash is skewed from the side of the handle in the lower part, it is lifted towards the upper fastening.
2. If it touches the upper part, it is turned towards the lower canopy or completely lowered down.
3. If it touches the handle area, the sash is moved towards the canopy.

Special bolts with a hexagon head are responsible for adjustment. They are located on the scissor system and at the bottom of the canopy. If the balcony door is skewed, everything will be somewhat more complicated - it is additionally equipped with closers that will have to be adjusted in parallel.

The height of the sash and the horizontal movement of the lower part are controlled by bolts located on the lower canopy. You can get to them by removing the platbands. The key is inserted inside the part - the required bolt is hidden in its very depths. The sash rises when rotated to the right and lowers when rotated to the left.

To prevent the sash from touching the frame from below, you need to tighten the bolt on the lower canopy

The tilt adjustment is similar, but a different bolt is used. The one you are looking for is located at the very bottom, it is located parallel to the canopy itself. Manufacturers have provided two ways to get to the desired bolt. It is easier to approach the bolt from the sash side if the sash is completely open. Otherwise, the second option is preferable. The adjustment bolt also rotates to the right or left to move the bottom in the same direction.

The mechanism is adjusted by turning the bolt clockwise or counterclockwise

Finally, you can move the top using the bolt located on the scissor mechanism. You can only get to it if you open the window completely. You can find the desired hole on the side - it is slightly recessed. Then everything is the same - turn the bolt clockwise or counterclockwise, periodically monitoring the process. After this, all that remains is to put the platbands in place and assemble the instrument.

Conclusion

As you can see, self-adjustment plastic doors and windows is a fairly simple matter. Even a non-professional can cope with this. Fortunately, if you act carefully, you won’t damage anything in the process. If any difficulties arise, you can always read the information on the manufacturer’s official website - perhaps you are dealing with some non-standard fittings with their own characteristics.