One of the options for using natural wood to decorate walls is to use wooden saw cuts. This method cannot be called widely known, however, due to the trends towards use for interior decoration exclusively environmentally friendly pure materials, it is increasingly gaining popularity. In addition to being completely harmless, a wall made from wood cuts allows you to bring a sense of naturalness and naturalism into the interior.

How to make wooden saw cuts

The process of making wooden cuts is quite simple and does not require any special tools. Tree trunks and branches of various thicknesses are used as raw materials, which, if available, summer cottage or proximity to the forest is not a problem. It is important to remember that cross-cutting has its own characteristic differences and uniqueness, depending on the type of wood. For example, pines and larches are characterized by the presence of transparent amber layers, and apple, cherry and oak are characterized by a combination of a dark central core with a lighter periphery. It is best to start by making sections of one type of wood, because using wood from several types of wood at once will require a certain amount of experience and artistic taste.

It is best to take blanks for saw cuts from freshly cut live twigs and branches, which abound in logging sites. There is plenty of such material when carried out seasonal pruning trees in the garden and at the dacha. Dry branches are less attractive in this regard, since they often have rot and cracks. It is better to cut branches into circles immediately after cutting them, while the bark is left only on the thinnest specimens. These works will require the following tools:

• hacksaw for metal or wood;
• cutter or jigsaw;
• sandpaper, grater.

The blanks are dried in a dry room for a month, after which they undergo light sanding so that there is no threat of splinters. All detected rotten areas must be treated with epoxy glue, which will prevent further destruction of the wood. To prevent damage to the received decorative elements various insects and microorganisms, used antiseptic impregnation. The final stage of material preparation is varnishing, for which diluted compounds are used. This is done to prevent the installation glue from penetrating deep into the wood, which leads to the formation of unsightly stains.

Decorating walls with saw cuts

Decisions on exactly how to decorate a wall in your home with a saw cut are made on an individual basis. Most often, the following decorative techniques are used for this:

1. Complete finishing of the entire wall.
2. Fragmentary decoration (a separate section on the wall, for example, the head of a bed).
3. Wall accessories (production flower pots, shelves, wall clock, various frames, etc.).

Preparing the base of the wall

Basically, the installation of saw cuts is carried out using a special mounting adhesive: in order for such fastening to last for a long time, the wall must be cleaned and leveled. If we're talking about O wooden surface, then it is best to use screws to fix each individual element. The same method can be used for concrete or brick walls in cases where saw cuts are used as separate fragments of decor.

When fully or partially finishing the base with wooden slices, you cannot do without preliminary preparation- in this case it resembles the preparation of walls for wallpaper. To do this, remove from the surface all layers that do not adhere well: this may be old paint, whitewashing, wallpaper, etc. Then the wall is primed with an acrylic composition, and, after it dries, plaster is applied: it is best for these purposes to use ready-made dry mixtures based on gypsum, since they dry much faster than cement ones. If the wall is smooth enough after this, then finishing putty You don’t need to do this: you just need to go over the base with coarse sandpaper No. 60-80, and then apply a layer of primer.

Another way to prepare for decorating walls with wooden saw cuts is to use plasterboard or plywood sheets to create a surface suitable for installation: this allows significant time savings, with some loss of living space. This is especially true in cases where the sheets are attached to the sheathing or profile. However, when fragmentary wall decoration is applied wood panels from saw cuts, then such a base is very convenient: for example, the same plywood can be pre-provided with the required color. In this case, gluing the cuts usually takes place without any problems.

Regardless of how the base was prepared, it is recommended to cover it with paint to match the future finish, so that there are no unsightly gaps between the individual cuts.

Panel from saw cuts

Regardless of whether the wall is completely covered with wood cuts, or partially, it is important that wooden blocks made up a certain composition called a panel. Quite often a technique is used in which only the reverse side of the scraps used is processed, which gives the resulting picture a natural uniqueness. Any abstract idea can be realized in the form of a panel: the thickness of the saw cuts used may vary, but the contours of the composition must be cut out in the same size. The abstractness of the subjects of such paintings is explained by the fact that using wood it is quite difficult to achieve clarity in the drawing.

To make a wall made of wooden cuts more exclusive, quite often, in addition to cuts, it is practiced to use branches, stumps and wood scraps. To fasten individual elements of the panel, liquid nails are mainly used, and the prepared flat wall is additionally covered with concrete contact. The finished wall decoration with saw cuts can be left in its natural form, or it can be painted in some colorful color: varnishing is another option. The end parts of individual wooden circles are often decorated beautiful ornament— family photos framed in this way look especially beautiful.

Making wall accessories

When making wall-mounted tubs, pots and flowerpots, their shape is determined by the outlines of the saw cuts. These products are especially original if you use not very thick branches from which small circles are cut. In addition, this approach will make it possible to preserve the essence of walls decorated with wood. The use of real plants and flowers allows you to further improve the combination of such pots with wood: this decor looks especially beautiful on walls of the same type made from saw cuts.

To make a shelf from a saw cut, you will need a thick beam from a solid trunk. The first manufacturing option is simply sanding the product, followed by applying varnish: this method is the simplest and most practical.

A more labor-intensive option involves sampling the middle from the cut of the trunk, followed by placing cuts of a smaller diameter inside it. This approach will give the shelf a special exclusivity: finished products can be varnished or painted.

As for wall clocks made from sawn wood, to make them you will need a real working clock mechanism. A hole is made in the center of the wooden mug, into which you need to carefully insert the arrow holder, having first removed them. This way the clock mechanism will be on the back side of the cut. After fixing the hands, the watch is ready for use, and as for the design of the dial, this is left to the taste of the owner of the house.

To decorate wall-mounted photo frames or mirrors, he uses saw cuts of small diameters: this approach will significantly enliven the design of the walls. They look very nice too wall hangers from saw cuts, for which medium-diameter slices inserted into frames are used rectangular shape. In this case, you will need to have knots on the saw cuts - they are used as clothes hooks. A corner in the hallway decorated in this way will look very chic.

Caring for finishing made from wooden saw cuts is carried out in the same way as for any other material made from natural wood. In this regard, the maintenance of a suitable microclimate in the room is crucial, as well as the use of surfaces for cleaning wooden products dry brushes, or slightly damp soft rags.

Just give a true designer free rein - he will decorate something like this! Someone chops wooden logs for firewood, and an interior designer brings them home, carefully saws them into thin plates and makes a wall or floor out of them.

Wood cuts look unusual and stylish in the interior of a house. Eco-friendly, natural, unusual appearance– this is what attracts eco-style lovers.

Design with wood cuts

No lining can compare in design with such wall decoration in country house. The forest-smelling wall will make you feel like a hermit, surrounded by centuries-old trees. Unusual design Making walls is quite simple, you just need to cut thin plates from a tree trunk, then carefully attach each “tile” to the wall with glue.

In this way, you can lay out the entire surface, circle by circle, or just part of the wall - in both cases, the effect will be amazing. The designers called this decor “an inverted wall” - it leaves the feeling that a woodpile of logs that have not yet been split has been laid in the room.

Of course, before decorating a wall with wood, it needs to be leveled; the cuts can be laid in any order - each tile will have a unique pattern, due to which the originality of the design is achieved.

Wood cuts in the interior

After attaching the saw cuts to the surface of the wall, it must be treated so as not to accidentally injure yourself due to the roughness of the wood and to avoid splinters. You can sand the surface, then cover it with stain or varnish. In addition, wooden saw cuts need to be treated with antifungal and insecticidal compounds.

This design is possible in a room decorated in the appropriate style, and the wooden cuts in the interior must be supported by at least a few more decorative elements, otherwise they will look alien. Properly selected materials for finishing the remaining walls, colors and furniture will create a harmony of space that emphasizes the unity of man and nature.

The use of wood cuts in the interior

Design with wood cuts

DIY room decor using wood cuts

Floor carpet made from wood cuts

If wooden slats can be placed on the wall, why not use them as a floor? This will take more time than decorating a wall, and more forest material will be needed.

To finish the floor, only tree trunks are taken, and the cuts should not be thin - the floor is larger than the wall, subject to loads, thin tiles will not withstand it. Instead of glue, a special solution is needed. The base needs to be leveled, the tiles from the saw cuts must be laid so that the surface is smooth.

The next step is to thoroughly sand the entire floor surface until perfectly smooth. Check the level during the laying of cuts and when sanding so that there are no unevenness or differences.

Just like walls made from saw cuts, the floor is treated with compounds that protect it from fungi and insects, then covered with several layers of varnish - you need to choose compounds for wood with a protective effect. The varnish will not only add shine and improve the appearance of the floor, but will also make it easier to clean.

Wood cuts in the interior

Apartment interior with wood cuts in the form of a tray

Furniture made from wooden saw cuts

In the skillful hands of a master, a piece of wood turns into... Yes, into anything:

• into the tabletop;
• into a chair;
• on a hanger;
• in the regiment.

All these pieces of home furniture can be made from wood cuts, you just need to choose different diameter, the thickness of the trunk from which the blanks will be cut.

For a small decorative table you need a wider log; the cut is not too thin. The table will turn out original if you leave the bark of the tree. The effect of naturalness and naturalness will be complete. Choose the legs to your taste, they can be metal or wooden, the table can be made very low, put a wooden tub with a flower on it, or higher - for magazines and newspapers. To protect against harmful bugs, treat the countertop with varnish with protective additives.

The use of wood cuts in the interior

Design with wood cuts

Room decor with DIY wood cuts in the form of a clock

It’s easy to make a decorative shelf from a cut tree, sawing it off from the trunk yourself or purchasing a ready-made one. From one round piece you will get two semicircular hanging shelves:

• cut a circle with a diameter of approximately 30 cm in half;
• take 2 corner fasteners for wall shelves, attach them with self-tapping screws first to the shelf and then to the wall.

All! The resin-smelling piece of furniture is ready.

Decorative elements from saw cuts in the interior

For those who create with their own hands, wooden cuts are an inexhaustible source of inspiration, a rich material for creativity. What can small and large wooden circles, sawn from a tree trunk or branch, turn into!

Wood cuts in the interior

Apartment interior with wood cuts

Panel from saw cuts

There are many options for making such decorative panels.

• You can place a thin cut cut in a baguette on a burlap or canvas base, complementing it with decorative elements.
• A panel of any shape, if desired, is laid out with thin plates cut from branches (as the creation of a wall was described above). Such a panel can be placed in an opening on the wall or framed in a baguette.
• The saw cut can be supplemented with a knot or a snag of an unusual shape - in this case you will get a voluminous composition unique design– it is impossible to find two identical snags or two saw cuts with the same pattern in nature.
• Not large diameter cuts from branches themselves can become the design of a baguette, photo frame, or composition made from natural materials. They are carefully laid out on the base, glued and varnished.

An interesting combination of two natural materials was invented by Ural craftsmen - a decorative design is applied to a wooden cut using finely ground stone chips. The Ural land is rich in gems, and the most interesting compositions are created without adding paints - the colored eyes of the earth, as gems are called, are so bright and varied that no paints are needed.

The use of wood cuts in the interior

Design with wood cuts

DIY room decor using wood cuts

Decorating the house

You can use wood cuts to decorate ordinary objects in an unusual way, laying them out like a mosaic, for example, the frame of a mirror, hanger, or flower pots. To do this, take thin branches, from which you need to cut them to the same thickness, but different diameters circles. Glue, varnish - and a stylish piece of furniture will decorate your home.

Eco style kitchen

You can make hot coasters for the kitchen.

• The central round element is removed from a large-diameter round piece, it is filled with small-diameter saw cuts, all this is attached to each other and to the base, and the top is coated with varnish.
• More can be done simple design, but two-layer - several small ones are attached to a saw cut of a larger diameter in a chaotic or specific order.

In the kitchen in rustic style Shelves decorated with twigs and saw cuts of small diameter would be appropriate. You can issue them kitchen apron, just pre-treat the wood with fire retardants. Cover the surface with varnish.

Wood cuts in the interior

Apartment interior with wood cuts

Unusual watch

You can make a clock for a rustic or eco-style home. The mechanism and hands are sold in craft supply stores; a ready-made saw cut can be purchased there, or a barrel of a suitable shape and design can be sawed. If you leave the bark on it, the unusual decor item will look even more original.

Drill a hole in the center and secure with front side hands, and on the back – a clock mechanism. You can paint the dial, or you don’t have to – this will make the watch look more stylish, just cover it with varnish to preserve it.

If, in addition to woodworking, you know the decoupage technique, you can combine these classes and decorate the surface using decoupage napkins or special decoupage cards:

• several elements that match the style of the interior are cut from a napkin;
• the elements are applied to the surface of the cleaned, sanded saw cut (to brighten the decor, you can cover it with acrylic primer);
• Using decoupage glue, the plot is glued to a wooden surface and smoothed out so that there are no air bubbles left inside;
• the entire surface is covered with varnish - the more layers there are, the more spectacular the object will be.

In the same way, you can make kitchen stands, cutting boards, and decorative tabletops from wood cuts.

The use of wood cuts in the interior

Design with wood cuts

DIY room decor using wood cuts

Knick-knacks for the home

It seems that functional purpose they have nothing, but they please the eye of everyone who enters the house, and if they are also made by your own hands, then accept compliments:

• Fridge magnets are a fashionable feature: a small saw cut is taken as a base, a magnetic tape is attached to it on one side, and the surface is decorated on the other using the technique of decoupage, leather applique, wood carving.
• Using an embroidery hoop, small cut circles and twine, you can create unusual panel. The basis can be linen, burlap, gray fabric or vintage canvas.
• Decorative wreaths are another fashionable interior item. Saw cuts are used as a decorative element, along with other natural materials– twigs, dried berries, flowers.

Wood cuts in the interior

Apartment interior with wood cuts in the form of a clock

Stylish, fashionable, unusual

Using wood cuts, you can lay out a composition on the wall, decorate a vase for flowers or fruit, or make an unusual frame for an embroidered painting or photograph. And how impressive the cover of a notebook or photo album, lined with small round pieces of wood, will look. There are many options for using saw cuts; human imagination is limitless, and there is no need to stop it. Compose, create, admire the fruits of your labor!

Video: Panel made of timber - decorating the wall with your own hands

All buildings and structures (gazebo, terrace, swimming pool, greenhouse, vegetable garden and different elements landscape design) at the dacha or personal plot communicated through paths.

What kind of path to make, or rather, from what material, everyone decides for themselves; specifically, within the framework of this article, we will consider making a garden path from chopped tree rings.

Among all the options (from boards, timber, panels, garden parquet, branches and bamboo), one of the most accessible in terms of material and the most complex in terms of design is paths made from wood cuts. The material is structured according to the principle step-by-step instructions so that anyone can build such a path with their own hands.

A path made from wooden saw cuts can be called differently: from slices, stumps (die, block, stump, log, ends of logs), but the construction method will be identical.

Garden paths from cut wood - step by step guide

For work you will need materials and tools:

1. Wood cuts (cuts)
2. Rolled waterproofing or geotextile (geofabric)
3. Sand, pebbles, gravel, water
4. Level
5. Hammer (preferably a mallet)
6. Hand chainsaw
7. Shovel, buckets, brushes

Step 1 - preparing wooden cuts

You need to start work with preliminary preparation of wood cuts (sections). Then they will be ready just in time for installation.

When choosing wood, you need to take into account how long the path is expected to be used and what load it will bear. When arranging garden paths from wood cuts at the dacha, it is better to give preference to hard types of wood. So, for example, oak will last you about ten years, pine - no more than seven. And larch is practically indestructible and will delight you for more than a quarter of a century.

But, most often, blanks for the path are made from those species that are available. It all depends on the budget; saw cuts from poplar will cost much less than from oak or larch.

To prepare the cut, you need to cut the log into pieces 150-200 mm high.

The rule that works here is that the larger the diameter of the log, the greater the height of the cut should be. And of course, the height of all blanks should be approximately the same.

If the thickness of the cut is less than 100 mm, there is a high probability that it will not be fixed in the ground and may “pop out” when pressed.

To extend the life of the saw cut, it must be cleared of bark. Because it is the bark that will begin to peel off first.

In addition, it is better to avoid using saw cuts that have cracks. They will begin to deteriorate first and very quickly, and the crack may increase under the influence of loads on it.

The cut also needs to be pre-treated. The most common treatment is drying oil.

To do this, it is heated to a boiling point and the saw cut is coated completely. Please note that this work is dangerous, so it is better to buy special antiseptic solutions that will provide both moisture protection and biosecurity. The saw cut should remain in this solution from two hours to two days.

To further protect the wood from rotting, the bottom of the round timber must additionally be treated with bitumen. You can age wood using a solution of copper sulfate.

The treated saw cut must be dried thoroughly.

Step 2 - marking the path

The difficulty of this step is in determining optimal sizes tracks - 350 mm, sufficient width for one person to move freely. As well as its route - to ensure access to all required facilities.

Step 3 - preparing the base

In order for wooden garden paths to serve you as long as possible and be safe, they need to be securely fixed.

To do this, you need to dig a trench along the marked route of the future path. Its depth depends on the length of the hemp (cut) plus 50-100 mm. (depending on the type of soil and the expected load on the path).

The width of the trench is equal to the desired width of the path.

A waterproofing film is laid at the bottom of the trench (you can use plastic film, used for greenhouses or geotextile).

Gravel or small crushed stone is poured on top of the film. This drainage is necessary to protect the wood from moisture. The height of the first layer of the pillow is equal to half the required height (25-50 mm). It is important to compact it well.

The sand and crushed stone bed must be leveled using building level. This will significantly save time and effort when laying cuts.

Step 4 - installing curbs for paths (edges)

If a curb is provided, then they must be installed before installing the cuts.

Stones, bricks, sheet iron, wooden blocks or long logs can be used as border material.

But, in order not to disturb the harmony of the garden path, chibouks sawn lengthwise are used.

Step 5 - pouring the second layer of sand cushion

Sand is used as the second layer. The total height of the pillow is 50-100 mm.

To compact the sand well, a technique such as pouring water on it is used.

Material prepared for the website www.site

Step 6 - diagram of laying wood cuts

The order in which the wood cuts are installed is not of fundamental importance. The formation of the pattern depends on the preferences of the owner.

It can be positioned so that there is as little space as possible between the cuts. Or, on the contrary, you can place them widely.

The main thing at this stage is to slightly “drown” the cut (compact) and also level them.

Step 7 - decorative design of a garden path from wood cuts

The space between the cuts can be filled with sand or soil mixed with seeds of ground cover plants.

Leave the saw cuts themselves in their original form or paint them with bright colors.

You can more clearly show how to make paths from wood cuts using a cross-sectional drawing of a path.

Caring for wooden paths

So that a DIY garden path made from wood cuts does not lose its quality over time. original appearance, she needs constant care.

To do this, you need to clean the cuts once a year with a metal scraper, treat them with an antiseptic and apply a special protective covering, drying oil or paint.

Advice
When you make a path, set aside a few cuts in reserve; in the future, you can replace individual elements during the repair process. In order to reduce the sliding effect after rain, do not heavily polish the ends of the logs before installation.

If you are interested in the process of making a path from wood cuts - a video illustrating how to make it yourself

Garden paths made from wood cuts - pros

• cheapness;
• high speed and ease of installation;
• the ability to carry out the entire process independently;
• do not accumulate moisture (do not create puddles);
• have a natural look;
• very repairable;
• environmentally friendly;
• opportunity to make a unique garden path made of wood. After all, all cuts are different, which means that the design cannot be repeated;
• the ability to use end-of-life logs as mulch or chop them up and add them to compost.

Country paths made from wood cuts - the cons

• subject to rotting;
• react to temperature changes;
• require constant care;
• become smaller after rain (evened out through the use of a special treatment compound).

Conclusion

Based on the foregoing, it becomes clear how to make a path from wood cuts with your own hands, without resorting to excessive expenses and outside help. Although, you shouldn’t rely too much on cheapness, even with self-production you'll have to spend some money, but this path is worth it

Interior design made in eco- and ethnic styles is becoming increasingly popular. Currently, designers are focusing on the naturalness and originality of the materials used. Thus, the decor from wood cuts in the interior looks stylish and organic.

Adds extraordinary comfort and warmth to the atmosphere of the room. In addition, such material is an environmentally friendly product, resistant to many types of influence and does not require large material costs. You just need to show your imagination - and ordinary cuts of wooden blocks will become beautiful decoration your house. Today we’ll talk about how cutting wood in the interior with your own hands can advantageously emphasize the individuality of your home.

Wood cuts as finishing material for house walls

Wall surfaces are the most convenient and extensive area for decorating a room. Here you can embody the most daring and creative ideas in the design of the room. This time as decorative element We will use wooden slices. They are smooth transverse layers of a tree trunk. Each layer has its own original and unique pattern, which is obtained from the growth rings of wood. Well, are you ready to get to work? First, let's find out how to make wood cuts for the interior. The process is extremely simple and even a beginner can handle it. Often, a transverse cut (also called an end cut) of a log takes part in the design.

1. We cut tree trunks into plates of the thickness we need. Their diameter can be different - this way the decorated surface will look even more beautiful.
2. We clean the cut from sawdust and shavings, you can also remove the bark.
3. We treat the layers with stain or special paint.
4. We apply an adhesive solution to each cut and place it on the wall.
5. You can lay out the wall plane partially or completely with cuts.
6. We wait for the glue to set and finally cover the surface of the glued sections with varnish.

Types of wood used for cuts in decoration

Important! The interior fits well wooden elements, decorative stones or plaster. Applying wood material for decoration, it should be taken into account that when cutting a log, cracks and cracks open. Consequently, layers of wood must undergo carpentry processing.

And provided that the wood material is planned to be used in functional role, then I advise you to restore the cracked sections of the cut. To do this, fill the damaged area with a special resin solution. After the resin has dried, we mill and sand the layer.

At decorative design The following types of wood are used:

• spruce;
• pine;
• fir;
• ash;
• birch;
• oak.

Completing finishing work, cutting of any type of wood must be covered with a paint and varnish composition. We discussed above how to process tree cuts for the interior (stain, paint, varnish).

• The main condition for quality work is a well-prepared and cleaned surface. The wall plane must be leveled and treated with a primer.
• Decide in advance exactly how you will decorate the surface. A wall with a partially covered saw cut will look good. It is not recommended to lay all the walls of the room with wooden plates, since the room will seem too small and overly cluttered.
• Partial installation looks natural in bedrooms at the head of the bed, in living rooms near fireplaces or modern electric fireplaces, as well as in the kitchen or hallway.
• Decorating surfaces with wood cuts is excellent for country and country houses.

Do-it-yourself panel from wooden saw cuts

The next popular way to use wood slices is in wall compositions. Their execution requires different types of wood and fragments of different sizes. In fact, this is an independent abstract painting made from wooden pieces. Wood plates are suitable either peeled from bark or covered with it. The compositions are also composed with the addition of stumps and branches. Decorate different colors or left in natural colors. Such a panel made from wood cuts in the interior looks original and elegant.

Flooring made from wood slices

Wooden materials are often used to cover floors. Round log plates are also widely used for this work. As a result, the surface is durable, environmentally friendly, aesthetically attractive and unusual.

So, let's see what technology is used to lay tree cuts on the floors in the interior. Finishing a floor surface is reminiscent of working with ceramic tiles. Installation is carried out using a special solution. After installing the elements, they are sanded and covered with several layers of varnish. The surface should be decorated using the following wooden plates:

Parameter	Function
Plate thickness	At constant load coating (furniture) and other mechanical influences, the surface made of a thin layer of wood can become deformed
Breed wood	Not recommended for use wood soft breed, because such the material is not resistant to loads. Oak and ash are suitable here. This coating will serve for many years without losing its attractiveness.

Masters and in general creative people find inspiration in any subject. Even a cut down tree does not go unnoticed. After all, by cutting logs you can make wonderful designer items that will serve as interior details and simply decorate a house or summer cottage.

Let's look at a few interesting ideas Application You don’t have to remove the bark from the trunk, so the work will turn out even more natural and creative.

Chair for the garden

You can use a chainsaw to cut such a comfortable chair from a large log for your summer cottage. To make it stable, you must first cut the base evenly and install it in its location. Next, start processing the seat. Here you need to act carefully so as not to make it too thin, otherwise when your body rests on it thin layer can break off and cause trouble for the person sitting.

The seat is cut straight. The bark on the front of the chair is cut off so as not to scratch the legs or tear the clothes of the person sitting on it. You can cut out the unnecessary part of the log from the back side. Then the chair will be much lighter, and it can be moved from one place in the yard to another. To make crafts made from wood cuts with your own hands look beautiful, they need to be sanded so that the surface is smooth. To make the wood shine and look brighter, you can rub it vegetable oil. Impregnated wood will not deteriorate longer. After several impregnations, the chair must be washed and dried. That's it, the piece of furniture is ready! You can sit down.

Original table

To make crafts from wood cuts with your own hands, you can use not only a whole log, but also individual sawn circles. To make such a table, you need to take two large cut circles and several small ones of the same thickness. The base is made slightly smaller than the tabletop. “Pancakes” made of wood need to be thoroughly sanded several times. First, a large one (100) is taken, then it is cleaned with a smaller one (80). The same preliminary work is carried out with all the details of the future legs of the coffee table.

An important point when making such crafts from wood cuts with your own hands will be clear, even planes of the circles. If the angle shifts, the table will come out crooked, and no one wants that. It is also necessary to follow safety rules when working with sharp tools and small parts.

When everything is ready, you can start assembling all the elements. The base is placed down, and a slightly smaller “pancake” is attached to it to weigh down the leg so that the table does not tip over. Next comes the most difficult part of the assembly process. “Pancakes” are installed with a one-third shift, first in one direction, then from the middle up the elements are shifted in the other direction. They should come together from above under the countertop.

One wide circle is also installed under the table cover so that there is a solid base and objects from the table do not fall onto the floor. Next, to make crafts made from wooden cuts look colorful, the tabletop can be varnished. The entire structure of the tree will appear, and the table will look bright and festive.

Flower stand

We offer another idea for crafts made of wood for a summer cottage. This is a beautiful stand flower pots. This stand can be used for other things as well. For example, place soap, a glass of toothbrushes, and dishes for washing on the shelves next to the sink. You can also put dishes with fruit on the shelves so that children, walking in the yard, can refresh themselves without running to the kitchen.

To make such a craft from wood cuts with your own hands, you need to select a large circle for the base. Then the entire structure will be strong and the stand will not tilt to the side. Next you need to cut out a section of wood with diverging different sides branches. Then the shelves will not overlap one another. In the largest circle, a hole is drilled in the middle according to the diameter of the branch, and it is inserted tightly into it. You can attach the base with glue or drill a couple of screws into the side from below.

Horizontal cuts are made on the branches different heights, and they are glued onto them or the shelves are clogged. They can be the same size or different. At the end, the cut of the tree at the DIY garden craft needs to be processed. If such a stand will be placed outside, it is better to wipe it with vegetable oil several times after sanding it. If the stand will be in the house, you can cover the surface with acrylic varnish.

Mirror decoration

Small circles cut from wood can be used to beautifully decorate a frame for a mirror or picture. You need to cut a lot of parts of the same thickness. To fill the space between large elements, small circles from branches are also prepared. The work is small and meticulous, because every detail needs to be processed. First, the bark is cut off, then each element is sanded several times. Next you will need to coat it with varnish. When all the elements are ready, a strong base is taken that will hold its shape well. It's better to take a sheet of plywood.

Place a mirror in the center and draw a template. Then the central part is put aside and they begin to design the frame. Work begins from the drawn circle. First, large elements are laid out, then the voids are filled. When everything is glued, time is given to complete drying. At the end, you can lift the work and make sure that nothing falls. Next, the mirror itself is glued onto liquid nails. Such beautiful item interior design will decorate not only the dacha, but will also look good in a city apartment.

Decor element

Now it is fashionable to hang on front door decorative elements. It is quite easy to make such a heart from wood cuts. Even a novice master can do this job. Saw cuts will do different sizes, the main thing is that the thickness is the same. Then all the elements are glued together to form the design desired by the author. It could be a heart, like in the photo below, or a butterfly or dragonfly. You can make your favorite cartoon character if there are children living in the house.

A screw is screwed into the middle, and a rope is tied to it, with which the picture will be hung on the wall or door. You can close the fastening with a bow or a flower made from ribbons.

Hidden drawer

Do-it-yourself country crafts made from logs can be very functional. For example, a great way to hide something from unwanted guests, who, unfortunately, sometimes visit other people's houses, is to make such a hidden box in a log. The photograph shows a unique piece beautifully crafted by a professional carpenter. But a safe hidden in a piece of wood can be made much simpler. The main thing is that this is a wonderful place where none of the uninvited guests would think to look.

A piece of log lies in a corner near the stove. Not even the most experienced thief will guess that something valuable is hidden there. So this is great advice. And every craftsman can cut a piece from a log. Then you need to close the box tightly so that the joints are not visible. Can round log turn it the other way too.

Conclusion

As you can see, you can make many useful and necessary things from logs using the sawing method, both for a summer house and for a city apartment, the main thing is to have the desire and time to make things. And we gave you ideas. Good luck!