Summer brings not only positive emotions and rest, because you shouldn’t forget about the annoying flies and dangerous mosquitoes that try to fly into the open window. A mosquito net is inexpensive, but if you consider that there are several windows in the house, then the end result is quite a decent amount, which, if desired, can be saved. A DIY mosquito net can be made quickly and inexpensively.
What is better - a purchased mesh or a homemade one?
Buying a window mesh will cost you about 1,500-2,000 rubles, so to save money, you can make it yourself. Many people wonder how to do it mosquito net on the window? This is not difficult, especially since everything you need can be bought at a hardware store. If you are interested in the question of what mosquito nets are made of, then the answer is simple - the material is durable fiberglass with the addition of weather-resistant PVC. The higher the quality of the material, the higher the protection against insects.
Before making a mosquito net with your own hands, take careful measurements and do not forget about allowances. If you are going to attach the mesh using Velcro or glue, choose something that can be easily removed and will not damage the window.
Several simple ways to make a mosquito net with your own hands
There are two types of mosquito nets that you can make yourself:
- Secured with fastening tape - simple and cheap way make your own mosquito net.
- Frame.
- Rolled.
One of the most simple ways Making a mosquito net with your own hands is done using special material and adhesive tape.
Take high-quality Velcro; the quality of fastening the protective mesh to the window opening will depend on this. You will also need special material with small cells. The smaller the cells, the better. Such material can be purchased at fabric stores, or you can use old products, for example, unnecessary tulle. It is best to purchase a special mosquito net - it reliably protects against insects and withstands weather conditions.
Mosquito net secured with adhesive tape
After all the measurements have been taken, take the material and cut it out, do not forget to leave small allowances. Divide the Velcro into two equal parts. Apply glue to one part and carefully glue it to the window opening. After the glue has dried, attach the mosquito net to the adhesive tape. Similar nets can be made for a car. It is done quickly and easily, with minimal costs. Instead of adhesive tape, you can use special magnets; this will significantly reduce the installation time of the mesh and simplify the process.
Frame window screens
A more expensive and complex method of making a mosquito net is the method with fastening to a frame. To do this you will need metal corners, a plastic cable and pop rivets.
The first thing you need to do is measure the window with outside, because this is where the mosquito net will be attached. Cut off the cable desired length, maintaining an angle of 45 degrees. Sand the sections and connect them using metal corners. Now make holes in the corners in which the rivets will be located. They should be on the outside, not inside the cord. Now all that remains is to attach the mosquito net itself to the frame. Do not pull the mosquito net too tightly, as this can deform or tear the fabric.
Frame window screens
You can make sliding mosquito nets with your own hands; they will fit well and protect the balcony opening or front door. A mosquito net on the balcony will help you prevent penetration dangerous insects indoors, will reliably protect even from street dust. The manufacturing technology is the same, the only difference is that the material is cut in the middle and the edges are processed. For convenience, you can attach magnets or rivets to the edges of the mesh, thus providing additional protection.
Rolled mosquito net
Rolled window mesh operates on the principle of roller shutters. It will reliably protect against insects, and it is convenient and easy to use. If you are interested in how to assemble a rolled mosquito net with your own hands, then there is nothing complicated here. You just need to be patient and have the appropriate materials.
You can make a mosquito net for a window of any size with your own hands. To make a rolled protective mesh, you only need a special box with a shaft and material. To attach the mesh to the window, use special magnetic latches. You can use screw fastening with an overlap or at the end of the guide in the opening to the slope. It is more convenient to use a rolled mesh than a regular one, and it is much easier to care for.
Rolled mosquito net
A rolled-up mosquito net for a window is an excellent protection against annoying insects. Allergy sufferers will especially appreciate this design - after all, it will protect the room not only from mosquitoes, but also from plant pollen and poplar fluff. It is best to choose a fine-grained material for such a mesh, this will increase the level of protection.
Making a mosquito net with your own hands is not difficult. If you need a mosquito net for a balcony or window, you can make it yourself quickly and without extra costs. Give this process a few hours and enjoy a quiet life without annoying insects! A homemade mosquito net is quite inexpensive. After summer, it can be removed from the window and carefully packed, and in next year hang it on the window again.
Homemade and the cheapest option for making a mosquito net without using a frame. This option involves attaching the mesh directly to plastic profile window.
Making a window mosquito net on a frame with your own hands in 150 minutes and 300 rubles.
I wanted to make a grid with my own hands.
This is what happened.
Required materials and approximate prices:
in my case, on a 175*80 cm grid:
Cable channel (15*10mm.) - 4 pcs. dl. 2 meters, (2m=15r.) total: 60r.
- Metal corner - 4 pcs. (I don’t remember the dimensions. It must fit into the cable channel) (1 piece = 14 rubles) total: 56 rubles.
- Blind rivet (4.0*6) - 16 pcs.
- Glue Super Moment Profi-1 pc. (bottle*5 g.) total: 80 rub.
- Mosquito net (1m*2m) (preferably thin, it’s easier to work with.
- Remaining sandpaper or a coarse grinding stone.
- Remains of a plastic corner 3*3cm. -20cm.
Tool:
Screwdriver or drill
Drill
Rivet gun
Roulette
Metal cloth
Pencil
Pliers
Miter box
Work order:
We measure the window, saw off the cable channel with a metal blade at an angle of 45* to size and sand the sawed area with sandpaper.
1) We measure the window, saw off the cable channel with a metal blade at an angle of 45* to size and sand the sawed area with sandpaper.
2) We connect the frame blanks and insert them into its corners. corners, after which we drill holes for the rivet in the cable channel.
3) We fasten the corners to the cable channel with a rivet. Be careful! The riveter must be located on the side of the cable channel or the cable channel will burst when riveting.
You will get this design:
4) The most crucial and difficult moment comes, we need to stretch the mesh onto the frame.
We put the mosquito net on the frame so that there is a margin of 2 cm on each side of the frame, and with the help of a second person we begin to stretch the mesh and snap (long side-short-long) the mesh with the upper part of the cable duct (it is important to take out all the slack, but not drag the grid - its appearance on the window will depend on this). After this, we cut off the excess mesh with a blade and “point” glue the mating parts of the cable channel along the entire perimeter of the frame so that during operation the cable channel does not disassemble by itself.
(unfortunately, there were no free hands to take a photo of this operation).
Here's what we got:
The mosquito net is ready, all that remains is to make the mount and secure it to the window:
Method 1: from a plastic corner 3*3 cm, cut off pieces of 2.5 cm, and measure the “depth” of the step (thickness of the cable channel). Cut off the excess with scissors. Then we glue the two corners with their opposite sides facing each other (one side of the upper fasteners should be twice as long). We attach the resulting “Z” with a self-tapping screw to window frame and insert the mesh, first into the upper fastenings, then into the lower ones, and lower it.
Method 2: from tin or sheet metal cut pieces 1.5*3 cm - 2 pcs. and 1.5*4cm - 2 pcs. we bend them so that we get the letter “Z”, drill a hole in them on one side for a self-tapping screw, then attach them to the window frame as described in method-1.
The simplest and quick way: we drill 4-6 holes in the window frame and our mesh and screw in flat-headed screws!
Mosquito net for 150 minutes and 300 rubles.
This grid is located on the second floor window. In the fall I take it down and put it up in the spring. Next season I plan to wash it with soapy water and a soft clothes brush.
This was a description of the first mosquito net. When making subsequent meshes, I did not make any changes to the process. The production of subsequent meshes takes much less time. To date, 12 similar meshes have been manufactured using this technique.
A plastic window will not be 100% functional without a mosquito net. In addition to its main function - protection from insects, the net protects your home from dust, poplar fluff and small debris carelessly thrown out by neighbors from above. If you decide to buy a mesh in finished form, take your time.
We will tell you how to make a mosquito net for a plastic window with your own hands for 72 rubles.
There are two reasons that encourage people to refuse to buy a ready-made mosquito net in a frame with fasteners. Firstly, this is the price, which depends on the size of the window and is approximately 700 - 1000 rubles. Secondly, the problem is where to store window screens in winter. They are quite large and take up significant space in the apartment, which is always not enough. The option we’ll introduce you to will cost you 10 times less and will take up no more space in your closet than a shoe box.
So, the choice is obvious, let's get to work. To do this, we need a piece of regular mosquito net the size of the width window opening, with an increase of 4-5 cm on each side. You can buy it at any hardware store. You also need to buy a cord, optimally with a diameter of 4 mm. Please note that the diameter must be indicated on the cord markings. When purchasing, you should not go by eye, since you will not be able to fix the mesh with a cord of a smaller diameter, and it will be much more difficult to deal with a larger diameter.
Installation of mosquito net
When necessary materials already in front of you, the installation of the mosquito net itself will take you no more than half an hour. Open the window sash where you will install the mosquito net.
Carefully remove sealing gum from the frame around the perimeter of the open window. There is no need to remove the sealing rubber on the sash itself.
Greetings, dear readers!
I love the peace and tranquility of countryside villages. There you can relax from the city noise and bustle.
At least once a week I spend my weekends at a friend’s dacha. But with the onset of warm weather, various flying insects became more active.
They tried to get into the house through the windows and interfere with a restful sleep.
We fixed this problem quickly. Now I’ll tell you how you can make a mosquito net with your own hands on a plastic window.
Now you can solve such issues yourself. By the way, you can order a window from us and receive mosquito net and 5 more gifts COMPLETELY FREE! Our prices will pleasantly surprise you:
- : manufacturing, installation
- Surface preparation
- Laying the tape
- Marking and installation
- Frame making
- Fastening the canvas to the frame
- Mosquito net on plastic windows with your own hands
- Types of mosquito nets
- Installation of frame grid
How to make a homemade mosquito net: 3 manufacturing methods
What is better - a purchased mesh or a homemade one? Several simple ways to make a mosquito net with your own hands:
- Frame window screens
- Rolled mosquito net
- Safety nets
- Selecting a canvas
- Restoration of mosquito nets
The simplest is self-production mosquito net using appropriate fine mesh material and adhesive tape for fastening.
This product will provide protection for the premises for several seasons.
You will definitely need the following components, which can be purchased at retail:
mosquito net with 1.2 mm mesh;
adhesive tape - one side of it should contain lint, and on the other there should be many small hooks;
glue for gluing cork or mosaic.
Surface preparation
Mosquito nets for plastic windows must be installed on a clean, prepared surface. The space is prepared by clearing open windows from dirt and degreasing them inner surface. To do this, you can use a soapy sponge, wiping it with clean gauze.
Considering that the installation is carried out on plastic windows, be sure to use only soapy water for cleaning, and in no case resort to solvents or alcohols.
Laying the tape
After cleaning the surface, separate the adhesive tape. Select the part with the hooks and glue it to the window opening around the perimeter using glue applied to the back side. Make sure that the tape does not interfere with closing the window. It is very important that it does not create difficulties in the joint area between the base of the window and the side where it closes.
It is easier to glue the tape if you do the opposite, apply glue along the entire perimeter of the desired area, and then, without making unnecessary measurements, cut the tape to the required length and width.
Marking and installation
Leave the tape for a while to dry and begin marking the mosquito net. Measure the perimeter of the opening and draw its outline on the canvas. When cutting, leave a margin that will be equal to the width.
You need to fold the overlap around the perimeter, and then sew on the second part of the tape, with the pile facing out. Make a seam from the edge; if necessary, you can make additional stitches in the middle.
After the hook tape is applied to the frame, wait about three hours. Then attach a net with fleecy tape to it. Now you know that making this design with your own hands is not so difficult.
Installation of mosquito net on frame
Certainly, next option is not the cheapest. However, costs can be minimized if installation on plastic windows is carried out independently.
Materials. You need to purchase:
metal corners, the width of which is about 1 cm, a plastic cable channel measuring 15x10 mm, glue,
about sixteen blind rivets,
the canvas itself is the right size.
Frame making
Since this kind of product is installed on the outside of the window, when taking your measurements, focus on this side of the window. Once the necessary data has been obtained, you can begin making the future frame: mark your received data on the cable and cut the required length at forty-five degrees of cut using a file or knife.
Sand the areas where the cut was made with a special sharpening stone. Compare the finished polished components of the future frame, connect metal corners. Holding them, make holes for the rivet in the finished cable channel, taking into account the holes in the metal corners.
Please note! Insert rivets into the resulting holes. It is important that the rivet device is located on the outside of your cable and not on the inside. If you don't have a riveter, you can use screws and nuts.
After tightening the screws, be sure to cover the nut oil paint to avoid screwing the nut during vibration.
Fastening the canvas to the frame
Having completed the frame, proceed to attaching your anti-mosquito cloth to it. It is better to use a thin mesh to avoid difficulties when clamping it in the cable. Place it on top of the frame so that the edges protrude 2-3 cm beyond the perimeter of the frame, and snap the mesh with the cable channel cover, alternating between snapping the short and long sides.
Be careful before securing the long side.
Don't forget to pull it a little towards the corner to remove any slack - but don't pull it too tight or you might tear it protective sheet. Once you've finished installing it on the frame, you can trim off any unnecessary excess sticking out.
In some locations, apply glue between the cable and the cover to prevent the cover from opening spontaneously.
How to install a finished one in a window opening
From a sheet of metal, cut two strips of 20x30 and 20x40 mm, bending them in a Z shape. Try to make the bend fit around the channel. Select the shorter side on which to drill a hole for the screw.
The finished fastenings are installed on the street side of the window, retreating about a centimeter from the window opening.
The fasteners are installed using a self-tapping screw, with long fastenings placed at the top and short fasteners at the bottom. The distance between the lower and upper fasteners should exceed the length of the frame by 1 cm. Start installation with the upper fasteners and finish with the lower ones.
Do-it-yourself mosquito net for plastic windows
With the onset of the first sunny days it becomes topical issue protecting your home from flies, mosquitoes, midges and other flying insects.
Useful advice! Owners of wooden windows traditionally attach gauze or mesh to the frame with buttons. And in other cases, a hand-assembled mosquito net for plastic windows can be a salvation.
A frame or roll mosquito net is easy to install and remove and does not require special care or strict rules during operation.
Types of mosquito nets
You can independently make two types of structures:
Velcro;
frame mosquito net.
The first option is simpler and more budget-friendly. Any woman can make and install such a mesh, even without special tools.
This is important! Frame meshes are more practical, they will last for several years, do not deform and retain their basic properties.
To make a mesh with Velcro you will need: fabric with a cell size of 1x1 mm; Velcro tape, on one side of which there is a pile, and on the other there are small flexible hooks-grippers; glue for balsa wood or mosaic tiles.
A strip of tape with hooks is attached with glue along the perimeter of the window frame. After this, the required piece of mesh is measured and cut out. The remaining strip of tape with fluffy pile is attached along the edge. It is recommended to attach it to the frame 24 hours after completely dry glue.
Making a frame mesh with your own hands
The frame structure consists of the following elements:
net;
painted aluminum profile;
frame fasteners;
crossbar;
fasteners for the crossbar;
plastic fastenings for corners;
rubber sealing cord;
handle holders for installing the frame in the window opening.
At the very beginning, we will tell you how to measure a mosquito net for a plastic window. Measurements must be taken with the window sash open. The height and width must correspond to the light opening. 4.5 cm of the window frame at the top and 4 cm at the bottom should remain free; fasteners for the frame will be installed on them.
Subsequently, when making the frame, it is important to take into account the width aluminum profile. His standard sizes– 25 mm.
Assembly begins with the preparation of the aluminum profile. Dots corresponding to the measurements are applied to it with a pencil, and vertical and horizontal slats of the frame are cut out from them. They connect with each other plastic corners, forming a frame.
The crossbar should be 50 mm smaller than the width of the mesh in order to be easily inserted between the side vertical strips. The main purpose of this element is to tension the mesh.
In the center of the frame, the mesh can shrink due to tension, and the bar will prevent this.
At first glance, it may seem that a DIY mosquito net for plastic windows is a complex design and can only be handled by experienced master having special tools in his arsenal.
This is important! In fact, when measuring and assembling, you can use available tools: a school ruler, a kitchen or stationery knife, scissors, and a screwdriver and a hammer can be found in every home.
After the frame frame is assembled, you can begin to tension the mesh. To do this, the frame must be turned over reverse side and place it on a stable horizontal plane. A piece of mesh is laid over the frame so that the protruding parts around the perimeter are equal.
Using a screwdriver or other flat thin object, thread the cord into the groove of the profile. It is placed on top of the mesh and holds it firmly inside aluminum frame. As you work, it is important to stretch the fabric and straighten the folds that form.
Handles for convenient installation mosquito net. They also roll under the rubber cord. The remaining mesh along the entire perimeter of the frame is cut with a blade or a stationery knife, giving the product a finished, neat and aesthetically beautiful appearance.
Installation of frame grid
Before installation, you should prepare the window frame profile. Its surface is cleaned of dust and wiped dry with a soft, lint-free cloth.
For installation, special fasteners are used, which are screwed to the frame with self-tapping screws. There are two fasteners placed on the lower horizontal strip of the window profile; they are slightly smaller in size than the upper fasteners.
For more convenient screwing, you can glue them to the frame with double-sided tape. After the screws are screwed in, it is recommended to process all seams silicone sealant to maintain the waterproof and thermal conductivity properties of the plastic profile.
Do not miss! Electrochromic glasses - what they are and why they are needed
The top fasteners are installed using the same principle. To calculate their location, you need to install the frame with the mesh until it stops on the bottom brackets, mark the height at the level of the top bar, then add 8 mm to this figure.
Please note! When installing the mesh into the fastening elements, you should hold the frame by the handles. First, the mosquito net is inserted all the way into the upper brackets, and the lower bar must pass freely over the lower fasteners.
The frame leans closely against window profile, then smoothly descends. If the upper fasteners do not hold the frame securely enough, it is recommended to reinstall them a few millimeters lower.
Removing the mosquito net (for example, to clean it from dust and debris) must be done as follows: holding it by the handles, the frame is lifted up, removed from the lower fasteners, then lowered down and out of the upper fasteners.
How to make a homemade mosquito net: 3 manufacturing methods
Summer brings not only positive emotions and relaxation, because we shouldn’t forget about annoying flies and dangerous mosquitoes that try to fly into an open window.
A mosquito net is inexpensive, but if you consider that there are several windows in the house, then the end result is quite a decent amount, which, if desired, can be saved. A DIY mosquito net can be made quickly and inexpensively.
What is better - a purchased mesh or a homemade one?
Buying a window mesh will cost you about 1,500-2,000 rubles, so to save money, you can make it yourself. Many people wonder how to make a mosquito net for a window? This is not difficult, especially since everything you need can be bought at a hardware store.
If you are interested in the question of what mosquito nets are made of, then the answer is simple - the material is durable fiberglass with the addition of weather-resistant PVC. The higher the quality of the material, the higher the protection against insects.
Before making a mosquito net with your own hands, take careful measurements and do not forget about allowances. If you are going to attach the mesh using Velcro or glue, choose something that can be easily removed and will not damage the window.
Several simple ways to make a mosquito net with your own hands
There are two types of mosquito nets that you can make yourself:
Frame.
Rolled.
Mosquito net secured with adhesive tape
One of the easiest ways to make a mosquito net with your own hands is using special material and adhesive tape.
Take high-quality Velcro; the quality of fastening the protective mesh to the window opening will depend on this. You will also need special material with small cells. The smaller the cells, the better. Such material can be purchased at fabric stores, or you can use old products, for example, unnecessary tulle.
Useful advice! It is best to purchase a special mosquito net - it reliably protects against insects and withstands weather conditions.
After all the measurements have been taken, take the material and cut it out, do not forget to leave small allowances. Divide the Velcro into two equal parts. Apply glue to one part and carefully glue it to the window opening. After the glue has dried, attach the mosquito net to the adhesive tape. Similar nets can be made for a car.
It is done quickly and easily, with minimal costs. Instead of adhesive tape, you can use special magnets; this will significantly reduce the installation time of the mesh and simplify the process.
Frame window screens
A more expensive and complex method of making a mosquito net is the method with fastening to a frame. To do this you will need metal corners, a plastic cable and pop rivets.
The first thing you need to do is measure the window from the outside, because this is where the mosquito net will be attached. Cut the cable to the required length, maintaining an angle of 45 degrees. Sand the sections and connect them using metal corners.
Now make holes in the corners in which the rivets will be located. They should be on the outside, not inside the cord. Now all that remains is to attach the mosquito net itself to the frame. Do not pull the mosquito net too tightly, as this can deform or tear the fabric.
You can make sliding mosquito nets with your own hands; they will fit well and protect the balcony opening or front door. A mosquito net for your balcony will help you prevent dangerous insects from entering the room and will reliably protect you even from street dust.
The manufacturing technology is the same, the only difference is that the material is cut in the middle and the edges are processed. For convenience, you can attach magnets or rivets to the edges of the mesh, thus providing additional protection.
Rolled mosquito net
Rolled window mesh operates on the principle of roller shutters. It will reliably protect against insects, and it is convenient and easy to use. If you are interested in how to assemble a rolled mosquito net with your own hands, then there is nothing complicated here. You just need to be patient and have the appropriate materials.
This is important! You can make a mosquito net for a window of any size with your own hands. To make a rolled protective mesh, you only need a special box with a shaft and material. To attach the mesh to the window, use special magnetic latches.
You can use screw fastening with an overlap or at the end of the guide in the opening to the slope. It is more convenient to use a rolled mesh than a regular one, and it is much easier to care for.
A rolled-up mosquito net for a window is an excellent protection against annoying insects. Allergy sufferers will especially appreciate this design - after all, it will protect the room not only from mosquitoes, but also from plant pollen and poplar fluff. It is best to choose a fine-grained material for such a mesh, this will increase the level of protection.
Making a mosquito net with your own hands is not difficult. If you need a mosquito net for a balcony or window, you can make it yourself quickly and at no extra cost.
Give this process a few hours and enjoy a quiet life without annoying insects! A homemade mosquito net is quite inexpensive.
After summer, you can remove it from the window and carefully pack it, and hang it on the window again next year.
Homemade and the cheapest option for making a mosquito net without using a frame. This option involves attaching the mesh directly to the plastic window profile.
Do-it-yourself mosquito net for the window
There are many devices for such protection. If you decide to save money on purchasing insect repellents or extermination products, then it is worth remembering some very unpleasant moments that may accompany your communication with mosquitoes, mosquitoes and other flying, jumping and crawling brethren.
After all, this is not just tremendous discomfort, the unpleasant sensation of being touched by the wings of an intrusive, ear-cutting sound.
What you need to know about the need for insect protection
Given the current environmental situation and the rapidity of mutations, even familiar, familiar mosquitoes and midges can acquire the most incredible properties and qualities. It is worth remembering that for thousands of years insects have been carriers and initiators of a wide variety of diseases - malaria, fevers and other epidemics.
Please note! Huge continents experienced waves of gigantic pandemics that practically wiped out more than half of the population, devastating cities and entire states. What could such tiny creatures do, it seemed? But they are the carriers of swamp fever and other equally dangerous tropical diseases, to which not only local population, but people of the European race.
Numerous historically famous travelers and discoverers and lesser-known “tourists” of the past and present, those who managed to survive after traveling to the tropical and subtropical regions of Africa, America and mysterious Indochina, accurately describe all the horrors of the diseases that were awarded to them by all kinds of flies and mosquitoes. If you have the opinion that this is anywhere but here, then you are completely wrong.
Today, huge masses of the population migrate to areas where such infections are widespread and there is a high probability that after a holiday in Malaysia or Singapore, some tourists will become passive carriers of a wide variety of pathogens.
And that's not all there is to worry about. No less interesting is that it is also worth thinking about own safety regarding your body's allergies. After all, the bite of such an inconspicuous insect can easily cause not just unpleasant sensations, but poses a real danger to life - allergic reactions are very different and very dangerous.
However, all this can be avoided by not only using medications, insect repellents and other chemicals. There is the most reliable and time-tested method in those countries where insects are common - mosquito nets on window openings and doors.
Today it is made from modern materials and different great design and elasticity. It not only perfectly protects against midges and mosquitoes, and the annoying fluff that is so annoying when poplars bloom.
Reasons for installing a mosquito net
These days, without exception, all models of plastic windows are offered by manufacturers complete with mosquito nets. So that she does not spoil your mood and does not interfere good review, you need to consult with specialists and choose the right everything that will allow the mesh to be ideal - the color of the canvas and the size of the cells.
Then it is practically invisible and does not pose any obstacle to sunlight and air flow. This is very important in the design modern window, where you can open it slightly or fully open it while maintaining the tension of the insect net.
Useful advice! This function is very beneficial for owners of homes and offices on the first floors of buildings in big cities and on central streets.
It is this simple device that has excellent protective function from dust, fluff, small insects and even minor street debris. And on high floors it can save the lives of your beloved pets - from a hamster, a parrot to a cat who loves to relax on the windowsills, watching what is happening below.
Equally interesting is that the mosquito net is easy to install, which makes it also very convenient to place on the door. Thanks to the fact that she can be the most different sizes and configurations, it is installed on windows and doorways any scale. Then you will have a calm and peaceful sleep, abundance fresh air in the bedroom, a cheerful mood in the morning and a boost of energy for the whole next day.
In most cases, installing a net against mosquitoes and other insects does not require any difficulties or special skills.
Features of the mosquito net design
No one has come up with anything new for hundreds of thousands of years. Mesh material is easy to use, and modern innovative technologies allow you to create a lightweight fixed-type structural model, which represents a simple frame with a canvas stretched over it.
This is the simplest thing you could do with your own hands to protect against all sorts of unpleasant sensations and consequences of mosquito bites. Making a mosquito net for a window with your own hands is very simple, you just need to study the technology and our manual well, and choose the right materials.
The technology of this simple device is simple:
You must first decide on the choice of canvas. The best option will be a fiberglass product coated with a rubberized compound, which is performed on the base chemical composition PVC;
manufacturing a frame that matches the geometry and size of the window or door opening where it will be located. They consist of a special aluminum profile for mosquito nets, connected at the corners with plastic parts;
applying the mesh and securing it using structural rings or clamps to secure the mesh fiber.
Do not miss! How to make it yourself roller blinds for plastic windows
If you have chosen this particular structure and type of fiber for the mesh, it will have the following qualities - resistance to atmospheric influences, excellent fire safety, without breaking on bends, and what is important for the external effect - it does not discolor at all over time.
Types of meshes and ease of use
Modern structural solutions for doors and windows simply amaze the imagination, and the possibilities of their flat, polyvariant opening make mosquito nets just as diverse. Today there are the following types:
It is important! frame. Suitable for any windows and doors, convenient and practical. Most suitable for those who like to make home improvements with my own hands, easy to wash and handle well, brackets and fastenings allow it to be removed for the winter months;
door. The same as the previous option, but the size of the door, fastened with special hinges, easy to install and dismantle;
roller shutter. It is convenient in that the design allows you to hide them by folding them into a special aluminum case at the top of the opening;
sliding. Used on terraces and balconies, it has an aluminum frame that moves along the lower and upper guides on rollers. Easy to remove and easy to clean.
And at the end of our story about the benefits of mosquito nets, I would like to hope that you will make a choice between adhesive tapes, poison sprays, fly swatters and mosquito repellents for the skin and the ability to simply make a mosquito net.
If you wish, you can purchase it, but one way or another, after installing it, you will no longer encounter insects, poplar fluff, plant seeds and banal street garbage in your apartment.
Moreover, the prices are very affordable, and the product itself is worth purchasing or making urgently.
Do-it-yourself mosquito net - manufacturing, assembly, installation
Annoying insects make it difficult to live and sleep peacefully at night during the warm season. They fly into the house through open windows.
Despite the presence large quantity special sprays and electric mosquito catchers, only a mosquito net can significantly reduce the number of insects.
Today, when replacing windows, you can additionally order this element, which costs money.
How to solve the problem on a budget? In fact, everything is very simple, since a mosquito net can be assembled with your own hands very quickly from available materials.
Safety nets
Before you go to the hardware store for all the necessary components, you should decide on the type of mesh.
They all differ in different parameters:
By type of fastening: hooks, Velcro, pins and Z-shaped brackets.
By type of opening: stationary, removable, sliding and roller.
According to the presence of a frame: framed and frameless.
Attachment location: internal and external.
Please note! Each of the listed types has its own advantages and features, but also disadvantages. All this is important to take into account in order to do right choice and don't waste your money.
Particular attention is paid to the method of fastening, so let’s figure it out: what are the pros and cons?
The frame is very rigid, because it is made of metal with a mesh fabric. Can be installed on both plastic and wooden windows from any side.
The sliding mount is only suitable for aluminum windows, since sliding sashes will be used.
A magnetic mosquito net is a very popular option for those who want to quickly get rid of insects. It is attached to both windows and doors. In the latter case, you don’t have to worry about cross-country ability, since the curtains easily open and close instantly.
Rolled mesh will allow you to conduct effective fight with mosquitoes. The material is easily rolled up and unfolded from a cassette placed above the window.
Simple Velcro is also easy to attach and remove. In this case, the mesh can be washed in the washing machine at any time.
Note! Mosquito nets are installed not only on windows, but also on doors, since mosquitoes and midges also penetrate through them.
Selecting a canvas
The main element of any mosquito net is the canvas. You can buy it at any hardware store by the meter or in a roll (about 30 m). If you only need to make a couple of grids, then it’s better not to spend money and buy required amount meters. For a larger number of protective nets, it is worth comparing prices: they may differ per square and per linear meter.
If we talk about quality, it is important to take into account several parameters:
cell size;
thickness of the canvas;
material type;
strength.
To create an anti-cat mesh, the strength parameter is very important, since it must withstand all “attacks” of domestic animals. The most ideal option For this purpose, polyester with special impregnation will be used. Additional fasteners are also required.
It is especially important to install such mosquito nets on the balcony.
When determining the size of the cells, you should take into account the size of the insects in the area from which you want additional protection. Minimum size cross-section is 0.25×1 mm.
Such a net can become a reliable protector not only from mosquitoes and flies, but even from sand, poplar fluff and dust. To protect windows and the room from rain, experts recommend a section of 1×1 mm.
Having decided on the materials and made the necessary purchases, you can begin production. How to make a mosquito net for a framed or frameless window yourself will be discussed below. The protection will be the same functional as from production.
Note! The quality of the protective mesh will be determined by the material from which it is made. IN Lately The most popular is fiberglass with a polymer coating.
Manufacturing of frameless mesh
This is the simplest and a budget option, which will allow you to make a removable mosquito net for little money. The easiest way to make the protection stationary is to simply glue the canvas to the window frame.
To make it better fixed at the edges, sew a tape of material with high adhesion properties. When it comes to wooden windows, ordinary push pins can serve as additional fasteners.
Useful advice! There is one significant drawback here - such a mesh cannot be removed for washing.
It's better to put in a little more money and effort to get universal protection. It's about about the Velcro mesh.
To make it yourself, you will need the following materials:
anti-mosquito material according to the size of the window;
Velcro tape (burdock - one side with pile, the other with hooks);
construction adhesive.
Measurements are taken along the inner (opening) part of the window with a margin of 1 cm on each side. This size is necessary to fix the future mosquito net.
One part of the adhesive tape is secured around the perimeter of the window using construction adhesive (for example, Titan) or simple double sided tape. The second is sewn along the entire perimeter of the mesh.
When everything is ready and the glue has completely dried, you can fix the protective sheet.
The entire work process takes a maximum of 2 hours, and as a result everyone receives reliable protection from insects.
Note! Before gluing the Velcro to the plastic, it should be thoroughly washed and degreased with alcohol.
Manufacturing of frame type mesh
Unlike the previous method, it is somewhat more complicated, but still anyone can handle it. It should be noted that such option will do and for making a mosquito net for the door.
So, to install the frame with your own hands you will need the following components:
cable channel rectangular section 15×10 cm (the length is determined independently based on the external parameters of the frame where the frame will be fixed);
metal corners 10 mm – 4 pcs.;
blind rivets – 16 pcs.;
thin nylon mesh;
construction adhesive.
Tools:
knife;
whetstone;
pencil;
scissors;
roulette.
Let's move on to the construction of the structure:
This is important! We take measurements of the outside of the window opening. Based on the data obtained, a frame will be made.
Celebrating on plastic box length and width.
Using a knife, cut the vertical and horizontal parts at an angle of 45°. The cut areas are carefully polished with a sharpening stone.
We assemble the structure: we fix the corners with special connecting metal corners with rivets (nuts and screws are also suitable).
We apply a mosquito net with an allowance of 2 cm on each side.
In the upper part we clamp the canvas with the cover of the plastic cable channel. During the snapping process, we change the long and short sides. For reliability, we glue some places with glue.
We cut off the excess fabric with scissors.
Ready mosquito net installed in the window opening using Z-shaped brackets.
Restoration of mosquito nets
An equally important process is restoration, which includes the following main stages:
Removing the frame from the brackets.
Cleaning from dust and dirt.
Removing damaged nylon.
Installation of the repaired mesh in the window opening.
Before replacing any element in the structure, you need to pay attention to how it is fixed and whether it can be removed. Most of the elements on the mosquito net from the manufacturer are fixed with a special sealing cord. If you carefully remove it, the holders can be easily removed.
Please note! Please note! All renovation work carried out very carefully. It is important to remember that you are working with a fragile structure.
As you can see, in order to make a mosquito net with your own hands, you will have to spend 2 or even 3 times less than when ordering a similar design from the manufacturer. In addition, the installation process is quite simple and does not require special knowledge or equipment.
An effective means of protection against mosquitoes and other small insects is a mosquito net. Can be purchased finished design, or you can make it yourself. The use of modern materials makes it possible to make mosquito protection for windows from a mesh material that will fit tightly to the window frame and have a neat appearance.
Types of protective mesh
Before starting production, you need to decide what type of mesh is needed. They differ in different parameters:
- by type of fastening - on hooks, Velcro, pins, Z-shaped brackets;
- by type of opening: stationary, removable, sliding, roller;
- by the presence of a frame: on a frame (frame), frameless;
- according to the mounting location: internal or external.
Below we will describe how to make frameless ones - stationary and removable, as well as a mosquito protection option - a mesh on a frame made of a cable channel.
How to make a budget version of frameless mesh?
The simplest version of a frameless mesh made by yourself is stationary. The canvas is simply glued to the window frame. But since the canvas itself does not hold well, you must first sew a strip of material with good adhesion around its perimeter. It can be any fabric tape. If installing on wooden window, the canvas can be additionally secured with buttons. The advantage of this method is maximum simplicity, the disadvantage is that the mesh cannot be opened or removed to clean it from dirt. That is, after some time it will have to be dismantled and the entire procedure performed again.
The second option is a mesh with Velcro. In order to make it yourself, you will need the following materials:
- anti-mosquito fabric;
- Velcro tape (Velcro, “burdock”);
- construction adhesive.
Part of the tape is attached with construction adhesive to the inner quarter. That is, to the part of the frame to which the window sash is adjacent when closing. The second part is sewn along the perimeter of the mosquito net. Before applying the glue, the area of the frame on which the glue will be applied must be degreased and cleaned of dust. The advantages of this type of frameless mesh are that it is “reusable”; if necessary, it can be opened slightly or completely removed. In terms of cost, it also belongs to the budget option.
To attach Velcro to the frame, it is better to choose a transparent rubber adhesive, such as Tytan, which can then be easily removed without leaving any residue. This is especially important if the window is plastic - rubbing and repainting it like a wooden one will not work here.
DIY frame type design
To make a frame with your own hands you will need the following elements.
- Rectangular cable channel (15×10 mm). The length is determined based on the outer perimeter of the frame, where the frame will be attached.
- Metal corners (10 mm) – 4 pcs.
- Blind rivets – 16 pcs.
The tools you will need are a metal file and a drill. First of all, the dimensions are taken - height and width. We cut 4 pieces from the cable channel at an angle of 45 degrees and fold them into a rectangle. Having placed the corners on top, you need to drill holes in the profile so that they exactly coincide with the holes in the corners. Then the structure is connected using rivets - and the frame is ready. Please note that when riveting, the riveter must be located outside the cable channel.
After the frame is ready, you need to secure the canvas in it. It is placed over the frame and snapped into place with the cable channel cover. To fasten it evenly, without sagging, you need to start fastening along one of long sides. In this case, you need to make sure that there is no distortion. Then the canvas is secured to one of the following sides of the frame.
It is better to fasten the opposite sides with an assistant, since here you will need to ensure light tension. At the same time, stretching the canvas, making sure that there is no distortion and snapping the bar in place is inconvenient, so an extra pair of hands will come in handy here. Frame-type mosquito net can be attached to a window different ways. The most common is the plunger type, using Z-shaped brackets.
To avoid the strip snapping off, it is better to additionally secure it with glue. To do this, when the structure is completely ready, you need to apply a small amount of glue into the gap between the cable channel and its cover (bar).
How to choose a canvas?
The main element in any such design is the canvas. It is sold in rolls and by the meter. There are about 30 linear meters per roll. If you need to make 1-2 designs with your own hands, then it is better to buy by the meter. When comparing prices, please note: they can be indicated both per square and per linear meter. In terms of quality, the canvas differs in the following parameters:
- cell size;
- thickness of the canvas;
- material;
- strength.
The last indicator is important for the anti-cat grid. She can withstand the “attack” of a pet; she is not afraid of cat claws and teeth. The most successful material for making anti-cat mosquito nets is polyester with special impregnation.
If there is a cat in the house, then you can only install a frame mosquito net. When installing, you need to take care of additional fasteners - the canvas to the frame and the frame to the window frame. This is necessary so that the animal does not fly out with the net.
The cell size is selected depending on the size of the insects in a particular area and what protection is needed from. The smallest cells have a cross-section of 0.25x1 mm. They protect not only from mosquitoes, but also from small particles of sand and dust. A canvas with cells of this size will also become an obstacle for poplar fluff. To protect from raindrops, the cross-section should be no larger than 1x1 mm.
The material from which the canvas is made has great importance. It is he who is responsible for color fastness and service life. Most reliable option– fiberglass sheet with polymer coating.
By choosing a high-quality fabric, you can make a good framed or frameless mosquito net with your own hands. She will have aesthetic appearance, and also meet all functional tasks. With it you can ventilate rooms without fear of uninvited visitors flying in: it will protect the house from mosquitoes, midges, and annoying flies.
