How to glue correctly vinyl wallpapers, preparation, gluing, working with corners.

In the previous article we examined in detail the types of vinyl wallpaper:

Someone will say that gluing vinyl wallpaper is not much different from gluing wallpaper on paper based. But when you read this article, you will understand that there are quite a lot of differences. And if you don’t take them all into account, then the wallpaper may fall off the next day, and you will have to do everything again, taking into account those nuances that you did not want to remember.

Tools

So, you will need to stock up on a fairly serious list of tools. First, you need a special brush designed for priming the wall and then applying glue to the vinyl wallpaper. Next, instead of a sponge, it is better to take a roller that will be used to roll the seams. You will also need a special spatula with which you will smooth the wallpaper, a soft sponge or cotton rag with which to remove excess glue, and a brush with which you will coat small areas of wallpaper. Little by little, you need to have scissors, a trimming knife, a level, a tape measure, paper tape, a ruler, and a wooden spatula with which you will press and straighten narrow sections of wallpaper, for example, at corners. Perhaps that's all.

Preparing the walls

Before hanging vinyl wallpaper, do the traditional wall preparation. You will need a special dry glue mixture for vinyl wallpaper, which must be diluted with water according to the instructions. Prime the walls with this glue over the entire surface. If you don't find glue, you can stock up on deep penetration primer, which is widespread everywhere. Further, since the wallpaper is heavy and does not allow air to pass through very well, the walls need to be treated with a fungicidal compound, protecting them from the appearance of mold under the canvases. After the glue and composition have dried, take a thread with a weight and fill a vertical line on the wall. This will be your guide for gluing the first piece of wallpaper. At the end of the procedure, turn off the electricity and remove all switches and sockets.

Additional Information

If you do not know how to glue vinyl wallpaper and have never done this before, it is advisable to have a person nearby who, as they say, is “in the know.”

Wallpaper is glued only to a dry, leveled surface, which is especially important for wide textured vinyl wallpaper. The old coating needs to be removed from the walls. Cracks need to be filled and the surface leveled.

You can check the dryness of the walls with a small piece of cellophane and masking tape, with which this cellophane will stick to the wall. Leave the material overnight. If in the morning drops of water have formed on the inside of the cellophane, then the walls are not dry enough to glue vinyl wallpaper on them. You'll have to dry it further.

The strength of the wall covering is checked using regular tape. Stick a piece on the wall and pull it away sharply. Look at the back of the tape. If there are particles of plaster or old paint, which means the wall needs to be prepared: remove old layers, prime and level.

Any person who knows how to properly glue vinyl wallpaper will tell you that there should be no drafts in the room under any circumstances. Air conditioners, fans, windows open wide – all this is a terrible taboo! Drafts are welcome only after the wallpaper is completely dry.

Never glue something new wallpaper covering to the old one. The latter must be completely removed from the wall. Wet them with water, wait a little, and then they will be removed with a spatula without any problems.

Preparing wallpaper

Cut the wallpaper into strips according to the height of the wall, but with a 10-centimeter allowance in reserve. If you are cutting vinyl wallpaper with silkscreen or regular pattern, then you first need to select a pattern of adjacent paintings with maximum coincidence. Place the wallpaper strips together with the pattern facing down. Each stack should consist of 10 strips of wallpaper, no more. And each strip should move relative to the adjacent one by at least 1.5 centimeters. It's best to take meter wallpaper, which allow you to minimize problems with selecting a pattern and correct cutting.

How is the glue applied?

Vinyl wallpaper is glued only end-to-end. This means that the panels should not overlap one another. After the primer has dried on the wall, you can begin the gluing process. First, apply glue to the section of the wall where the first panel will be located. Stick the canvas on the wall, coat the next one and glue it. The sequence of actions is repeated until the end of the work.

Additional Information

You need to work with glue very carefully, since carelessness will lead to adhesive composition on front side wallpaper

Allow the mixed glue to swell thoroughly by standing for 5-10 minutes after mixing. This rule must be stated in the instructions.

Read the information on the vinyl wallpaper roll. It is quite possible that the glue needs to be applied not only to the wall, but also to the wallpaper.

How to properly glue vinyl wallpaper?

Technology correct gluing. Wallpapering alone will not work. Only double. And even faster - three of us. One worker stands on a stepladder or on a chair and places the top edge of the canvas against the wall. Another worker holds the bottom end of the strip on the floor, aligning the edge of the wallpaper with the designated vertical line. Next, lightly press the wallpaper strip towards the base, after which all air bubbles are forced out with the help of a brush. The brush is used from top to bottom and from the axis towards the edges. If you notice any glue coming out at the edge of the canvas, quickly wipe it off with a clean rag, not a brush!

Trimming the edges

When gluing wallpaper under the ceiling and in the area of the baseboards, you should have excess material left, which can be trimmed along a ruler with a knife. In this case, the lower edge of the strip should extend onto the baseboard by about 5 millimeters. Wallpaper should only be trimmed with a sharp knife. If the blade is dull, it will tear or dent the wallpaper that has not yet dried from the glue. During the pruning process, regularly replace the quickly dull blade.

Canvas at the baseboard

If you did not remove the baseboard before starting work, insert the bottom edge of the wallpaper between the wall and the baseboard. The remaining part is cut and glued with a strip on top, which will close the seam and top part baseboards. I strongly recommend removing the baseboard before wallpapering so that it does not interfere with your work. At the end of gluing, it is nailed down or put back.

Gluing the top

The edge of the wallpaper adjacent to the ceiling must be turned up 5 centimeters to protect the ceiling from glue. After this, the wallpaper strip is pressed against the wall from above and smoothed downwards with a brush. Other canvases are glued in a similar way. If you are not gluing wallpaper up to the ceiling (for example, you have paint or plaster on the top of the wall), then you must first mark the upper boundary of the gluing area on the wall with a pencil. This should be done around the entire perimeter of the room. The strip will help you navigate the work process.

Working with corners

In the corners you need to leave excess vinyl wallpaper to the depth of the existing niche, taking into account the allowance. After this, cuts are made at the top and bottom, and the panel is folded around the corner using the pressing method. Next, the wallpaper is carefully trimmed, and in the corners where the panels overlap and the joints are pressed firmly against the wall, ensuring tight adhesion. I note that in the corners of the room the wallpaper should extend to the other side by a maximum of 3-4 centimeters. At the same time, on the other wall, the first canvas is glued from the very corner, covering the previous 3-4 centimeters.

Sockets, switches, batteries

Behind the batteries, the walls should be covered with approximately 10-20 centimeters, no more. The wallpaper is pressed against the wall using a narrow roller equipped with a long handle. They can work both behind the battery (top, bottom, side) and through the radiator fins. Wallpaper near switches and sockets is not cut in advance. They are glued directly to the holes. Only after the glue has dried can the cut be made.

General information on wallpapering walls:

Which concrete mixer is better to buy, types of concrete mixers.
Aerated blocks for house construction, production and application.

When it comes to renovation, the question arises of how and with what to decorate the walls of apartment premises. The most optimal choice Will wallpaper it. It is best to choose vinyl ones because they have a large number of advantages, and also very attractive in appearance. They have long term service, basically all kinds of wallpaper data are easy to clean. Some can only be wiped with a damp cloth to remove any resulting dust, while others can be wetted and even cleaned with a sponge. In order to choose exactly the detergents, it is best to consult a competent seller of a specialized store. Or you can inspect the packaging yourself and find identification marks that indicate the degree of resistance to moisture.

Immediately before hanging vinyl wallpaper, difficulties arise, namely, what tools you need to have in order to easily hang wallpaper, what stages the gluing process includes, how to properly prepare the walls, and many other similar nuances. This article will reveal the answers to these questions.

Required Tools

Before you begin the gluing process itself, you need to make sure that all the tools are available and prepare them so that they are at hand at all times.

You will need the following tools:

a special brush used to prime the walls;
brush and roller for covering wallpaper with adhesive mixture;
a special lint-free roller is necessary for rolling seams;
a special soft spatula for evenly smoothing the canvas;
masking tape;
cotton napkins or rags to eliminate excess glue that has come out;
a small brush will be needed to lubricate the wallpaper;
a stationery knife for even cutting, scissors will not work;
a spatula or wooden spatula for pressing and straightening uneven areas in small areas.

With these tools, wallpapering will be easier and more convenient. The main thing is to have them on hand.

Preparing the walls

No need to ignore this item, since wall preparation is important stage. Thanks to the competent and careful preparation Wallpaper covering the walls will last a long time and delight you with its beautiful appearance.

Initially, you need to remove a layer of old wallpaper, if any. After which it is necessary to prime the walls, it is best if this is done using a special primer that is aimed at deep penetration. If suddenly there is no such thing, then diluted adhesive mass will cope with this task. After the walls are primed they need to be coated special means, which prevents the occurrence of fungi and the development of microbes.

After time has passed, when all the layers have dried, professionals advise drawing a line the entire height of the wall and using it as a guide for gluing the first strip. You should not focus on the corner of the room, as it may be uneven, which may cause problems with the drawing. To be 100% sure that the drawn line is perfectly straight, you need to use a special building level.

As soon as everything preparatory stages the walls are finished, it is necessary to isolate the premises from current and remove all existing sockets and switches. This will allow the canvas to lie perfectly on the wall surface. There is no need to neglect this and do it as before, just cut a hole for this or that element. This will result in an uneven pattern and all the beauty of the canvas will be lost.

Important! Vinyl wallpaper should always be glued only to well-dried walls. To be sure, you can attach polyethylene to the prepared wall for a day using masking tape, and if after this time moisture has formed on it, this means that the wall requires more time to dry.

The room where Finishing work it is necessary to isolate from the air flow, namely, tightly close all windows and doors, turn off heaters and air conditioners. You can ventilate the room only after the vinyl wallpaper has dried thoroughly.

Step-by-step instructions for gluing vinyl wallpaper

How to glue vinyl wallpaper on non-woven backing?
Non-woven vinyl wallpaper has a number of features that you should know:

apply glue only to the wall;
no need to allow gaps during application adhesive solution, and its layer should be thick;
gluing should be done from an even angle;
wallpaper is glued only end-to-end and not in any other way;
The strip applied to the wall must be smoothed strictly from the center to the edges.

The non-woven base contains a large amount of cellulose, making the fabric denser and heavier. To properly glue such canvases, it is better to use glue for vinyl wallpaper on a non-woven basis. On store shelves it is referred to as vinyl glue. It is produced on the basis of methylcellulose and is completely PVC-free. As a rule, it is considered universal and is suitable for any type of vinyl wallpaper.

If wallpaper of this type is planned to be glued in a room with high humidity, then it is better to purchase polyvinyl acetate glue. It will ensure reliable adhesion and long service life.

Required time to dry non-woven vinyl wallpaper

Wallpaper with non-woven backing has different drying times. First of all, it depends on the manufacturing method. For example, wallpaper made using hot embossing requires an average temperature of approximately 25 degrees and a humidity of no more than 60% to dry completely. Then up to completely dry you should wait 48 hours.

If the canvas has decorative finishing, then they may require a longer period, in some cases a week.

Rules for gluing paper-based vinyl wallpaper

The key to success in gluing paper-based vinyl wallpaper is the correct adhesive. It is important that its composition is of high quality, this will avoid the formation of bubbles and unevenness. And it will also serve them for a long time. It is best to choose glue from foreign manufacturers. They certainly have a higher price category, but the costs will definitely pay off high quality. It is important that the adhesive mass has the ability to quickly set to the surface, but not instantly.

The glue must contain compounds that are aimed at preventing the formation of mold and fungi.

High-quality glue has the following characteristics:

when the adhesive mass is diluted, no lumps or clots of unknown origin should appear; if this occurs, then it is better not to use it, as this can lead to unevenness;
does not dry out after a day;
can be stored for years in an unopened package;
must not contain harmful substances;
easy preparation of the mixture.

Before gluing paper-based vinyl wallpaper, you need to carefully level the wall surface.

Divided into types:

putty;
plaster;
drywall.

The stages of gluing wallpaper with a paper backing are no different from other types of vinyl wallpaper.

Drying wallpaper with paper backing

How quickly this type of wallpaper dries depends on many factors. First of all, a significant point is the well-dried, prepared surface of the walls. If it was not dry, then the drying time of the wallpaper will be increased several times.

The best option is if the room temperature is approximately 20 degrees and the humidity is no more than 70%. If the temperature is lower and the humidity is high, then you will have to wait quite a long time for the walls to dry. In addition, this can lead to peeling and deformation of the canvas.

Important! It is possible to ventilate and carry out further finishing work only after the coating has completely dried.

Vinyl is not one of the latest innovations, so there are a lot of tips and recommendations on the issue: how to properly glue vinyl wallpaper, as well as what glue to use. At the beginning of their existence, they were called “washable wallpaper” because the vinyl base is durable and resistant to water. Vinyl wallpaper has a number of advantages over paper wallpaper, for example, you can safely repaint them later.

How to glue vinyl wallpaper? Vinyl wallpaper is completely different from wallpaper that has a paper base. There are many nuances in gluing them, they should be taken into account. Since vinyl wallpaper has two layers ( upper layer made from polyvinyl chloride, and the bottom layer is made of non-woven fabric or paper), they are glued with a special glue, it is intended for heavy wallpaper. By the way, the good thing about this wallpaper is that it allows air to pass through well, and from many different structures you can choose the one that is ideal for your room.

Read also:

What they represent.
What are the features?

About, You can find out how to glue wallpaper on the ceiling.

Required Tools

So, how to glue vinyl wallpaper and where to start? Prepare everything in advance necessary tools, this will significantly speed up the pace of your work.
You will need:

roller for rolling seams;

a special brush for priming and applying glue;

brush for small areas on wallpaper;

spatula for smoothing wallpaper;

sponge (soft) or cotton fabric, in order to remove excess glue;

scissors;

roulette;

A small spatula can be very useful; it will be convenient for pressing the wallpaper in the corners, as well as straightening it in narrow, inconvenient places;

stationery knife;

ruler;

level and paper tape.

Return to contents

Preparing the base for gluing vinyl wallpaper

First of all, you need to carefully prepare the walls: get rid of the old coating, be it plaster, paint or wallpaper; clean the base from greasy stains if there are cracks, they need to be puttied (the putty must dry well before you proceed to the next step); walls must be smooth and strong. You can check the strength of the walls as follows: cut a small piece of tape, stick it on the wall, if after you sharply pull it back, paint or other wall covering remains on the backside, then the base requires careful preparation before starting work.
Next you'll need to prime. To do this, separate cold water(following the instructions) dry glue, which is intended for vinyl wallpaper, then apply to the walls. Wait for the soil to dry completely, this will take approximately 3-4 hours. Then treat the walls with a fungicidal compound, which will prevent mold from appearing under the canvases. While waiting for the composition to dry, prepare a thread with a weight attached to it, and use it to draw a vertical line along the wall.

This will make it easier for you to navigate when you glue the first sheet of wallpaper. Before you begin gluing the canvas, you should turn off the electricity in order to remove all sockets and switches from the walls.

What else should you know?

What glue to use.

How to glue correctly.

It is important to note that when hanging vinyl wallpaper, be sure to close all windows, fans and air conditioners should not be turned on (there should be no drafts in the room).

To make it easier for you to get rid of old wallpaper, you need to wet the walls with water. Then, after waiting a little, you can easily clean the surface with a spatula.

Return to contents

How to properly glue vinyl wallpaper?

First, prepare the vinyl wallpaper for gluing. Cut them in strips according to the height of the wall; leave allowances of about 10 cm on the strips. If the panel you choose has a pattern, you need to select the pieces so that the pattern matches. Fold the fabric into a stack with the pattern facing down.

Return to contents

Instructions for preparing glue

The glue is mixed in a cup of suitable size with the proportion of water you need. Pour in the glue slowly, while stirring to avoid the formation of lumps. Then the glue should sit for 5-10 minutes; after mixing again, you can start gluing.
What glue to use for vinyl wallpaper? A store consultant can advise you on what kind of glue to use for the wallpaper you have chosen.

The selection of glue is an important detail, since the texture of this material comes in several types. And the result of your work depends on the answer to the question of what glue to use to glue vinyl sheets. The edges will have to be given Special attention, there should not be a single uncoated area left. Therefore, coat them with a brush, and for the rest of the area you can use a roller. Glue is applied to required area on the wall, in some cases also on wallpaper (carefully read the instructions on the wallpaper packaging). Apply glue evenly thin layer, then fold the wallpaper so that its bases match. Leave them in this position for 5 minutes.
Press the fabrics with a roller or brush (the bristles of which should be short) and iron all the seams properly.

Russia, Moscow region, Moscow +79041000555

How to properly glue vinyl wallpaper with your own hands?

Takes ~6 minutes to read

Progress in the field of materials presented a gift - vinyl wallpaper. The well-known PVA glue has been learned to foam and sinter on rolls of paper, while imitating surfaces various materials, including the silks of the imperial palaces. Although vinyl wallpapers have nothing to do with silk, they are often called silk-screen for their specific appearance. The vinyl is actually applied using the tinted dot printing method. After heating, the substance swells, the points merge - the process is completed. Warm stripes are sometimes embossed and rolled under paint rollers. The design can be applied before embossing. The production is not complicated, but the components used are expensive. Palace collections of vinyl trellises can hardly be called budget-friendly. However, vinyls that are properly applied to the wall will last forever.

Save

Features and types of vinyl wallpaper

Depending on the substrate, wallpapers are divided into:

paper,
non-woven fabric,
fabrics.

The first ones are the cheapest, the acrylic on them is foamed, so the substance is easily destroyed even with a fingernail. Non-woven fabric is used as a substrate for denser samples. Vinyl on a fabric base is similar to a sieve, calico. Used where there is a complete imitation of tapestry.

Save

Based on density, vinyl is divided into two categories:

high relief,
low relief.

High-relief ones are produced in wide canvases white with the texture of matting, two-thread, linen canvas, as well as ribbons in the form of plaster decor. After gluing, such reliefs are painted with acrylic paints. For kitchens and hallways, decorative canvases are produced in the form of tiles, brickwork. The service life is limited: rearranging furniture, children, pets, the inability to wash with abrasives are the reasons for the rapid destruction of the layer.

Low-relief washable, not afraid of impacts, do not fade, without unpleasant odor. Their only drawback is the ability to condense steam on themselves. That is, they do not “breathe”. Therefore, they are recommended for rooms and premises with good ventilation.

They produce vinyl in 4 standards: 53 cm, 70 cm, 106 cm and ribbon friezes. All varieties, regardless of the height of the relief, series and manufacturer, are combined with each other. The main thing in the gluing process is to avoid gaps between the canvases. Overlapping vinyl is not glued.

How to glue: necessary tool

Metal ruler;
Stationery knife;
Square;
Roulette;
Flat brushes – 0.5, 2.5 cm;
Fleecy roller on a stick – L 200 mm;
Roller on the handle – L 120 mm;
Leveling scraper;
Construction level (preferably laser);
Simple pencil hard T;
Shoe brush;
Scissors.

Save

You will also need a fiberboard board, a table, a stepladder, rags, masking tape, and weights to prevent the canvas from curling. The glue used is methylcellulose CMC or modified starch.

Glue selection

CMC stands for: methylcellulose glue. All its other names are an advertising gimmick. CMC is poured in very small portions (dust) into a bucket of water, mixing thoroughly. Set aside for a few hours and stir again. The liquid should be viscous, like jelly, and envelop the stick without lumps. The jelly-like consistency is the same for all vinyls - heavy, light, high-relief. Very thick glue is diluted with water, but carefully, in small portions, otherwise it may become a watery liquid.

Save

Another wallpaper glue– modified starch. It dries without a trace and does not form whitish streaks. Its price is higher, but the preparation is the same as that of KMC.

PVA glue is added - up to 10% of total mass- just before gluing to speed up the setting of meter prints, but it is not mandatory. The excess is thoroughly blotted with rag swabs.

Preparatory work

Removing old wallpaper

The gloss of vinyl reveals all the unevenness of the wall, so the surface is prepared more carefully than for painting. The chalk is washed off the wall, the old wallpaper is scraped off with a spatula and a knife, after soaking it.

Sometimes you need a lot of water. An oilcloth is placed on the floor on the bars; the flowing water will be collected in an oilcloth ditch. Each time you roll a dampened roller over old wallpaper, it will peel off faster. The washed wall is allowed to dry.

To remove old wallpaper in one large layer, they resort to the following: newspapers are glued onto the old paper print. Let it dry and peel it off.

Wall leveling technology

Scrape off oil paint. Large sinks are sealed with plaster and impregnated with primer. Next is the application of the “Start” gypsum mixture. Afterwards the walls are sanded. Before the finishing layer, it is recommended to glue fiberglass canvas. Fiberglass will serve as a flavoring agent during gluing. It also reinforces the finishing layer. All fiberglass glue is the same. The final layer is “Finish” putty.

Save

By applying a light source to the wall, the dried surfaces are checked for the presence of small cuts and protrusions. After straightening, the surfaces are primed again. The final stage– sizing. The glue prepared in advance is rolled with a roller.

Very old walls are easier (and cheaper) to level with plasterboard. In this case, transverse and longitudinal guides are attached to the wall with a pitch of 1200 mm, the slabs are hung, the screw entry points and the seams are puttied. Reinforcing mesh is not applied along the seam. Finishing layer It is not necessary to apply putty mixtures to drywall, but the slabs are primed and glued in the same way as in the previous case.

Marking

Surfaces are measured. Use a level and a pencil to mark the top edge. The highest canvas height in the entire room is set (it can vary). Usually it is 2 m 65 cm +. In the case where the design involves two tiers and a frieze, markings are made along the horizons.

Save

Installation ceiling cornice done either before or after gluing. In the first case, the junction of the cornice and the canvas is covered with acrylic between two masking tapes. The top of the acrylic is tinted with water-based emulsion (it turns yellow over time). In the second case, the wallpaper protrudes 5 mm above the bottom edge of the plinth, and the top of the wallpaper is covered with polystyrene cornices, having previously been protected from contact with construction protective “painting”!

You need to mark out the entire composition in advance. Particular attention is paid to verticals. Using a level, a vertical is drawn for each canvas, otherwise a “slipped” section can initiate a crook for all subsequent ones.

Step-by-step instruction

To properly glue such wallpaper with your own hands, follow the instructions below.

Fabric preparation

The roll is rolled out, inspected for defects, and the length is cut off in accordance with the marking rectangles. You need to cut in one step, using a backing board, with a blade well secured in the handle. The transverse line for cutting must be strictly perpendicular.

Save

How to apply glue

The cut is placed on the floor, pressing the corners with weights, preventing them from twisting. The glue is rolled with a roller without squeezing in a painting tray. The vinyl lining absorbs a lot, so after the first rolling, they immediately roll it again. It is advisable to lubricate the contours of the canvas with PVA in addition to CMC. The top and bottom are brought to the center. The formed envelope is soaked for 3 – 5 minutes. Unfold it, placing it against the wall. It is advisable to use two people to avoid tearing.

Save

How to glue the finished canvas

Before gluing the finished piece of canvas, you need to pay the greatest attention to the top edge. Once it is fixed in accordance with the marking line, the canvas is finally unfolded and its center is fixed by hand. Holding the top edge, they pass over the canvas with a spatula-smoother. Subsequent movements are from the center to the edges. Excess glue is removed with a moistened rag swab, the canvas adheres perfectly. A shoe brush is used. Use it to level the canvas in a circular motion, check the side edge with the horizontal, and if necessary, move the edge back and slightly pull it up. The wet cut is elastic and stretches at a meter thickness of up to 1 cm. Do not touch the moistened wall with nails or sharp objects - it is very vulnerable.

Trimming edges

Vertical canvases by wet wall you can't cut it. The groove from the knife will remain, moreover, it can provoke the destruction of the putty. But on a plasterboard board, the canvas can be trimmed - in those places where there are no nests, under self-tapping screws, away from the seams. After drying, the strips are cut close to the floor.

The tape material - friezes - after stretching along the wall, are pulled out. It is difficult to predict their final length. The tape is measured, cut to excess, laid, the border is marked with a pencil and carefully trimmed with scissors.

Pasting in problem areas

No adhesive on water based will not withstand temperature changes behind the batteries. You can’t even see behind them: the curtains camouflage you. But it is possible to choose a color and paint it over. To mother-of-pearl suitable for wallpaper acrylic paint with shine: silver, gold, bronze. These compounds are extremely stable. The edges of the vinyl of the batteries are painted on the back side with thick PVA glue and pressed. Hold it, for example, with a mop. Such work can only be carried out near cold radiators.

The housings of sockets and switches are removed before gluing. It goes without saying that the network must be turned off. Dried trellises on rosettes will reveal themselves in relief; they are easy to detect by touch. A cross-shaped hole is made in the center, and the unnecessary one is cut off.

Drying time for vinyl wallpaper

Determining whether the moisture has evaporated or not is simple: you need to touch the wall and ceiling with your palm. Normal drying wall materials- day. In autumn, the drying period may be delayed - up to 2 or 3 days.

After complete drying, check the joints. If the sticking has come off, cover the edge on both sides with masking tape, carefully pull it back, drip PVA glue from a stationery dispenser, press it and dry it with the warmth of your palm.

Video: how to properly hang vinyl wallpaper with your own hands

Good work requires care and strict adherence to technology. But working with vinyl cannot be considered a labor-intensive process. However preparatory work voluminous and costly.

The procedure for gluing vinyl wallpaper begins with an assessment of the purchased canvases and wall surfaces premises. Wallpaper must be from the same batch, identical in color and pattern. The walls are free of defects, curvature, etc. But they are rarely like this even in new buildings, so it is necessary to prepare them.

When purchasing wallpaper, you need to take into account that the seller is not responsible for defects that appear on them during gluing and for the results of gluing in violation of the instructions.

Suppliers accept claims for differences in color or article numbers strictly before the roll has been cut. Refunds due to other defects are only possible if no more than one roll is pasted.

Preparatory work

Proper wall preparation

If there is old wallpaper on the walls, remove it. The removal method is selected based on how high quality the glue was. Several withdrawal options are possible:

dry,
using a steam cleaner,
by soaking,
using a specialized wallpaper remover.

If the surface was previously painted or whitened, it is cleaned and washed.

When preparing new walls, skip the first stage and immediately move on to the second - leveling. All defects (cracks, irregularities, holes, etc.) are eliminated with masking tape, plaster, primer or putty.

After this, the wall must be completely treated with a primer. It is selected in accordance with the initial data.