IN last years more and more in the assortment of markets, construction materials stores and the Internet can be found on the shelves meter wallpaper. They are different from wallpaper standard sizes almost twice as much, because their width is 106 cm. What are their main advantages over their smaller counterparts, and how can you accurately make your choice? How to glue meter-long non-woven wallpaper? What is the technology for gluing such finishing material? After all, for so long we have used the standard 50 cm width for our living spaces. We will try to answer these questions.

To glue all types of wallpaper on a non-woven backing, prepare approximately the following set of tools and materials:

How to glue meter-long non-woven wallpaper - Sequence of work

The process of gluing meter-long wallpaper itself differs little from pasting ordinary wallpaper, but it still has its own nuances. Let's look at each in more detail:

Preliminary preparations

We remove the finish and clean out rough edges and residues in the form of paper, newspapers and other unnecessary debris. The entire preparatory part can be divided into the following steps:

1. Unscrew the covers of sockets and switches, and we strongly advise you to turn off the electricity in the apartment for a while. Seal the holes and door frames masking tape, which can be easily removed upon completion of the repair.
2. Remove all hooks, screws, nails and dowels from the walls.
3. Clean completely old finishing, carefully so that no traces of the former decor remain.
4. Clear the room of debris and carefully inspect the room again.

One of the advantages of non-woven wallpaper is the fact that it is not afraid of shallow unevenness in the terrain, chips and scratches. Moreover, if the working cleaned side is a little rough, then this will be rather a plus and will make it easier for you to work with them.

Primer

Leveled, clean plastered surfaces must first be coated with a primer, which will treat and close numerous barely noticeable pores. Its use will significantly save glue consumption in the future, in addition, it will not be excessively absorbed into the plaster, which also guarantees stable adhesion of the canvas.

After applying the primer solution, all dust is finally removed from the walls. Keep in mind that if you apply glue to untreated walls, some of it will be absorbed very quickly, and the consumption will increase significantly, and there may simply not be enough glue. Wait for the primer to dry completely, then you can start gluing the wallpaper.

Marking

Taking into account that this is meter-long non-woven wallpaper, it is important to take into account that they have to be glued at the joint. The width of the roll is 106 cm and it is supposed to retreat one meter in each direction from the corner. As experts advise, it is more correct to start pasting from the window, moving sequentially into the room. For the first sheet, you need to do the following:

• align exactly vertically using a plumb line;
• draw a clear line with a pencil, use a construction ruler or level.

Preparing the adhesive solution

When purchasing glue, pay attention to what type of wallpaper it is intended for; in this case, it is necessary for non-woven wallpaper. The method of preparing the solution itself is described in detail on the packaging, and manufacturers often accompany the description with visual pictures. Even an amateur can cope with this, because there is nothing complicated here. You need to pour water into a previously prepared container, and slowly pour in the dry mixture, at the same time stirring with a stick or other available materials. The main thing is not to stop stirring until the glue is completely dissolved, otherwise lumps will form. Then you have to wait no more than 10-20 minutes and the glue is ready.

Wallpaper cutting

Cover the floor with plastic film, now you can roll out the roll front side down. If you have a pattern on your wallpaper, then you have to adjust it when cutting the panels. Add 10 cm at the top and bottom to the desired length for extra space.

We begin to paste over

Having successfully completed all the preparatory steps, you can proceed to the final stage - directly to gluing. Before applying the glue, you will have to mix it again. Then we immediately proceed to applying the adhesive layer. For easier and faster coverage, use a special roller or wide brush with long pile. The technology for gluing non-woven wallpaper is such that there is no need to smear the strips themselves, it is enough to coat only the desired part of the wall. There is no need to apply glue to large areas of the wall; try to stick to the width of the wallpaper sheet plus 5 cm in reserve.

If necessary, straighten the strip, align it along the edge, smooth out all air bubbles using a plastic spatula for leveling wallpaper or a special roller. Swipe it from top to bottom, as well as to the sides from the middle of the canvas. Remove any excess glue with a small sponge or clean rag, without rubbing, but gently blot. Continue gluing the remaining prepared strips sequentially. This should be done end to end. If there is a pattern on your wallpaper, then try to carefully combine it with the adjacent sheet. Due to the large width of the roll, the process of transforming a room goes much faster. Try to complete this stage carefully and conscientiously, taking into account that this is not standard wallpaper.

After gluing the panel and its complete adhesion, we remove excess wallpaper (left in reserve) using a previously prepared sharp construction knife and a plastic spatula. Try to press the edge as tightly as possible for an even cut.

Due to the fact that meter-long wallpaper is noticeably wider in width than standard wallpaper, we recommend that two people do the wallpapering. Find an assistant for yourself - working with him is incomparably easier and the results will not be long in coming.

It is recommended to close the windows interior doors and other sources of drafts. It is necessary to close the ventilation and technical hatches. It is allowed to open the windows only after the glue has dried 100%; the wait may take from one to three days.

The basic principle of gluing non-woven wallpaper in the corners is as follows. The strip should be glued so that there is a slight overlap on next wall. An impeccable look is an overlap of no more than two centimeters. Then we glue it on the other side of the corner with a slight overlap. Afterwards, cut off the remaining “tail” with a knife, adhering only to the vertical angle (along inside angle).

Advantages and disadvantages

Before you go to the store and choose meter-long wallpaper, it is advisable to familiarize yourself with their advantages and disadvantages. We believe that immediately after carefully studying all aspects of gluing, you will have a more or less clear picture regarding the choice in favor of one type or another.

pros

• There are few joints on the walls and they are almost invisible.
• The time required for all work is reduced. After all, it’s easier to measure and stick 10 strips than twice as many.
• Cost savings, because the price of a roll of large wide wallpaper is, at least a little, but after all lower, in contrast to two rolls of standard size.

Minuses

• Difficulties in matching subsequent strips to the previous, already glued sheet.
• It is difficult to cope with pasting on your own.

We suggest watching a special video lesson for a more clear example.

How to glue meter-long non-woven wallpaper video:

This coating, as you understand, has a number of important positive qualities. We hope that after reading our article, you have a clearer idea of ​​how to properly glue meter-long wallpaper. We wish you a successful repair and may the result make you happy!

Nowadays, meter-long non-woven wallpaper is gaining relevance every year. This is not surprising, since hanging such wallpaper will be at least 2 times faster than standard material. You don't need any special skills to hang this wallpaper. It is important to level the concrete walls very well, otherwise the joints will be uneven. As soon as the walls are leveled, you need to wait until the putty dries, prime it, and then stick the wallpaper.

After the wall is prepared according to the rules, you need to apply pre-prepared glue to it.

The advantages of this type of finishing material are obvious:

• Gluing takes little time;
• Doesn't leave much waste;
• After work, there are fewer joints.

All this cannot but affect the quality of work and appearance. But, despite the advantages of wide non-woven wallpaper, there are still suspicious people who buy regular wallpaper, believing that sticking them on will work out without problems, faster and better. In fact, working with non-woven wallpaper is quite simple. The main thing is to properly prepare the walls and glue them with your own hands and it will turn out flawlessly.

It is important to remember that for this type of wallpaper a special glue is used, which can be purchased at a specialized store.

After the glue is applied, you must perform the following steps:

1. Take a piece of wallpaper and adjust it to the height.
2. Start gluing the canvas along the marked line on the wall surface.
3. We turn the other side of the canvas at an angle.
4. Immediately begin smoothing the wallpaper from top to bottom, expelling air bubbles.

For smoothing, tools such as a rubber spatula, wallpaper roller or a cut of clean material are well suited. thick fabric. As soon as the smoothing is completed, it is necessary to trim off the excess wallpaper at the ceiling and at the lower baseboard. It is convenient to cut with a sharp stationery knife, and use a metal spatula as a guide. If wet wallpaper is difficult to cut, you can wait until the material dries.

For those who have decided to glue wallpaper themselves for the first time, we recommend reading the following material:

Self-gluing of non-woven wallpaper end-to-end

Pasting using butt technology will be completed fully if the walls have been carefully leveled. When the walls are perfectly smooth, the non-woven fabric is glued end-to-end to the second sheet to be glued, without overlap.

The butt gluing process is carried out as follows:

1. Special glue is applied to the wall.
2. The canvas is glued end to end.
3. As soon as the joint is made, it is necessary to urgently expel the air.
4. It is forbidden to achieve a joint by stretching the canvas; when the wallpaper is dry, there will be gaps between the canvases.
5. The excess near the ceiling and floor is cut off with a stationery knife.

Experts recommend using one small trick. If you can’t glue it end-to-end, then you can glue it with an overlap of about 3-4 cm, and after the wallpaper has dried, use a sharp utility knife to make a through cut in the place where the canvases intersect. In this case, both sheets are cut at once. After the cut is made, the trimmings must be removed, the joint should be lubricated with glue, and the blades should be straightened, resulting in a smooth, neat joint.

Even more useful tips to achieve perfect result in wallpapering:

How to properly glue non-woven wallpaper in the corners of a room

The first method is used when covering a room with wallpaper with a pattern.

This method involves gluing the canvas strictly from the corner with an overlap of 2-3 cm over the previous canvas. This method allows you to hide defects in the case of a crooked corner. The second method is ideal for non-woven wallpaper of the same tone, a material without a pattern.

Step-by-step execution method

1. The canvas is glued from the corner.
2. Both canvases are cut with a stationery knife.
3. The excess is removed.
4. The joint is coated with glue.
5. The canvases are carefully aligned.

This technique cannot be used when gluing wallpaper with a pattern, since cutting it will destroy the structure of the pattern. It is also important to apply the glue correctly; there should be no more or less of it, just enough so that the canvases can adhere to the wall. On concrete wall and an equal amount of glue is applied to the drywall, but the composition is not applied to the canvas at all. As you can see stick it wide wallpaper very simple, a little time, patience and the result will impress you. At least gluing non-woven fabrics is much easier and faster than regular ones narrow wallpaper.

Is it possible to glue non-woven wallpaper onto old wallpaper: expert advice

If a person bought non-woven wallpaper and plans to carry out the repairs with his own hands, then he will be interested in learning a few nuances, for example, information about which surface is best for gluing the finishing material.

Non-woven wallpaper can be glued to different surfaces, among which:

• Porous concrete;
• Plaster;
• Drywall, etc.

You should not glue non-woven wallpaper onto paint, as it will peel off; you should also not glue canvas onto old wallpaper. Craftsmen say that old paper wallpaper has a tendency to bubble after re-pasting, which will not have a positive effect on the result of the work. It’s clear why you can’t put wallpaper and paint on old ones, so the most the best option is to remove the old coating, prepare the wall and paste it with good, high-quality non-woven wallpaper. Pasting this type Wallpaper should eliminate the possibility of a draft, in addition, you need to turn off the air conditioner and start gluing from a window or corner.

Is it possible to paste wallpaper on non-woven wallpaper: expert recommendations

As mentioned above, glue non-woven wallpaper onto old surface Not recommended. The result may not be pleasing. Interior finishing specialists recommend working with a previously cleaned and prepared wall.

Craftsmen like to work with this material, and they note the following advantages of non-woven wallpaper:

1. Long service life.
2. The canvas does not stretch, does not dry out, and does not deform.
3. Easy to stick, easy to remove.
4. The canvas has different relief and patterns, which makes it possible to play with the design of the room.
5. Wallpaper increases sound insulation.
6. Improves fire resistance.
7. The canvas allows air to pass through well.
8. Environmentally friendly composition.

To make the repair easy, experts recommend that before starting work, you read the rules, which describe in detail what you should pay attention to and what you should not do. Knowing the rules, everyone can glue it correctly; no special skills are required in this case.

Home craftsman: rules for gluing non-woven wallpaper

Before unpacking the wallpaper, you need to check for defects. Next, experts recommend studying the icons and their descriptions located on the wallpaper. Carefully read the rules for preparing walls. If you plan to stick thin non-woven wallpaper, then you need to prepare the surface in the same way as when gluing vinyl wallpaper and thin paper wallpaper. Next, you need to correctly calculate the amount of material used. When cutting fabrics, you must follow the technique, then you will be able to avoid high flow rate. You need to buy glue specifically for non-woven wallpaper and before diluting it, you should carefully read the instructions. The glue is applied not to the canvas, but to the wall; we must not forget about this nuance.

When working, you should only use quality tool, wallpaper spatula, which:

• Smoothes out wallpaper;
• Removes excess air;
• Removes excess glue.

You should only work during the daytime, when you don’t have to turn on the lights, this will avoid electric shocks while wallpapering near sockets. Cold air currents should also be avoided. To install the border, you need to use special glue. If the canvas is smooth, then you can glue the border onto the already glued canvas, but if it is embossed, then you should first glue the border, and then begin work on pasting the room.

A metal ruler and a sharp knife work well for trimming.

The room should be warm and dry, optimal temperature indoors 22 degrees. In order to glue the area around the socket, you must turn off the electricity, remove the socket, stick the cloth, cut out a cross inside and trim the corners. You need to work with glue as carefully as possible, you should not smear a lot of glue, and you should also avoid getting glue on the front side of the wallpaper. It is better to glue it end to end, since when gluing it overlapping, the result will be terrifying; the wallpaper is very dense. It is necessary to glue very quickly, as the glue dries quickly.

How to glue non-woven wallpaper (video)

How to glue meter-long wallpaper.

IN Lately in shops building materials More and more often you can find wallpapers meter width, that is, a non-standard size familiar to our people. What is so good about this wallpaper, how to glue it and should you give it your preference?

1.Wide wallpapers undoubtedly have many advantages over the usual thin types. Thus, meter-long wallpaper simplifies the work of pasting, reduces the number of seams, which often spoil the overall appearance of the room, and also reduces the cost of purchasing such material for wall decoration, since one meter-long roll of wallpaper costs a little less than two similar small ones.

2. Prepare wallpaper, special glue for non-woven wallpaper, a construction water level, a pencil, a tape measure, a roller and a bucket for glue, a plastic spatula, a soft bristle brush, a knife, plastic film and a roller for rolling the edge.

3.Prepare the room. To do this, you need to completely remove the previous coating, level the walls if necessary, remove all sockets and switches, and insulate the wires. Mark the room. Marking should begin from the corner of the room, since the wallpaper will overlap there. Set aside one meter on both sides of the corner and use a pencil and level to make a vertical mark, approximately at the height of your height. Make such marks every 1.06 m (the width of the tube), marking the exact distance with a tape measure.

4.Spread the film on the floor of the room so that the wallpaper does not get dirty and glue does not get on the floor. Determine the height of the wall by measuring it with a tape measure. Roll the tube face down onto the film. Mark your length (wall height) + 10 cm.

5.Fold the roll and return to the starting point with it, so that by cutting off the length, you end up with two strips of wallpaper. Run your finger along the fold, making it smoother and more precise.

6.Cut the folds with a prepared, well-sharpened knife. Prepare, therefore, strips of wallpaper for the entire room.

7.Dilute the wallpaper glue according to the instructions and let it stand in the bucket until it swells completely. Dip the roller in glue and spread the area on the wall for the first panel (first strip). Take this strip and apply it to the wall. Remember that pasting the strip starts at the top (from the ceiling) and extends downwards.

8.Take a brush and smooth the panel along its entire length from the middle to the edges. Do the same steps with a plastic spatula. The canvas should fit tightly to the wall and have no bubbles. Cut off the margin left near the floor, if there is one. In this case, take into account the width of the plinth, which will be subsequently fixed.

9.Glue the second strip in the same way. When gluing a corner, the wall should be generously coated with glue. Here two strips of wallpaper are placed on top of each other, that is, the pasting occurs overlapping. In this case, the wallpaper is pressed tightly with a spatula and the corner is cut, after which the seams are evenly joined. Take a roller and carefully roll it over the seams. Carry out the same actions with other canvases, connecting them to each other along the intended lines.

Typically, warehouses use pallet and shelf racks for storing small-piece goods. And clients overpay for such storage of small-piece goods from 1.5 to 2.5 times!! Warehouse complex "OPTOMIR" saves cash their clients, because here they have developed and are successfully using a technological solution for storing small-piece goods. Watch an interesting video on how this is done on the company’s website http://optomir-sklad.ru/msht/ and send a request to calculate the cost of storage. "OPTOMIR" will save you from overpayments for storage from the first month of service.

Recently, on the shelves of construction hypermarkets and in the virtual windows of specialized online stores, you can increasingly see wide meter-long wallpaper for sale. They differ from rolls of standard sizes by almost 2 times, having a width of 1 meter, or more precisely, 106 cm.

What are their main advantages when compared with their usual analogues and how to choose them correctly? And most importantly, how to properly glue wide wallpaper? After all, over the years, many of us have become accustomed to gluing standard rolls half a meter wide. So let's move on to look at these interesting questions.

Unlike standard ones, it is better to glue wide wallpaper together

Detailed instructions: how to glue meter-long non-woven wallpaper

The process of gluing meter-wide non-woven wallpaper includes several main stages. Let's look at each of them in more detail and find out how to glue meter-long wallpaper:

• Preliminary preparation of the wall. We remove the old wallpaper and remove any remaining unevenness in the form of paper and other residues. The advantage is the fact that wallpaper with a non-woven base is not afraid minor irregularities surfaces, chips and scratches on the walls and partitions of the room. In addition, if the prepared working surface is slightly rough, this will be rather a plus before starting work.
• Then you need to close all windows, vents and other sources of drafts. It is recommended to close even technical ventilation openings. Moreover, it is allowed to open vents and windows only after completely dry glue, which can take from 24 to 72 hours. It is also recommended to turn off the power for a while, remove the sockets, remove them from the walls various elements fasteners: nails, screws, etc.
• Preparation adhesive solution and wall surfaces. Be especially careful when purchasing adhesive as it must match the type of wallpaper. The process of preparing the solution itself is not complicated and even a non-professional can easily do it with their own hands. Pour water into a pre-prepared container and gradually add dry glue, while stirring with a small stick or other available means. Read the glue instructions: it says how long it will take for the solution to harden sufficiently and be ready to start work. As a rule, you will not have to wait more than 10-20 minutes. Once the glue is ready, you need to mark the wall. Considering that this is non-woven, and, moreover, meter-long wallpaper, it is necessary to take into account that they will need to be glued at the joint - this is exactly what will be correct. As reviews and expert advice say, it is better to start gluing from the window, moving deeper into the room. As for the first sheet, align it vertically with a plumb line, and draw a line with a regular pencil using a long meter ruler.
• The next stage is cutting wallpaper for gluing. Leave 10 cm at the top and bottom as a margin. After completing the work and completely drying, you can remove excess (left in reserve) sections of wallpaper using a previously prepared sharp knife.
• Let's start gluing. Having successfully completed all the previous instructions, you must proceed to next stage works - directly to gluing. Before applying the glue itself, you need to mix it again. After this, we proceed to applying the adhesive layer. This is done using a wide brush for wallpaper glue. As you know, non-woven wallpaper is not coated with a layer of glue. It is enough just to apply it to the surface of the wall. After applying a layer of adhesive solution, carefully smooth the wallpaper. This stage must be performed efficiently and conscientiously, taking into account that you are gluing wide meter-long wallpaper. If necessary, straighten the wallpaper, level it and get rid of air bubbles using a special plastic spatula for leveling wallpaper. Smoothing can also be done using a plastic comb or roller, downwards and away from the middle of the wallpaper sheet. Remove excess glue with a small sponge or rag.
• We continue gluing the remaining cut sheets. This needs to be done at the joint. If necessary, you need to accurately select the pattern so that it matches the adjacent sheet of wallpaper.

Related article: Empire style in the interior

Due to the larger width of the roll, gluing work is done faster

Advice from the experts! Since meter-long wallpaper is much wider than standard wallpaper, it is recommended that two people hang it together. Therefore, before starting work, find yourself an assistant - it will be much easier to work with him.

Pros and cons of gluing meter-wide wallpaper

Before gluing 1-meter wallpaper, it will be useful to learn about their advantages, as well as some disadvantages. The fact is that only after a detailed study of the pros and cons of gluing wide canvases, you will have a more or less accurate idea regarding the choice in favor of one or another option.

Advantages

The advantages certainly include the following points:

• After repairs, fewer joints remain on the wall.
• The time for preparation and execution of work is reduced. After all, even despite the fact that meter-long wallpaper has O The thicker thickness compared to standard analogues is still easier to measure and glue 15 sheets than 30.
• You can save additional money, since the price of one tube of wide meter-long wallpaper, although slightly, is still lower than that of two tubes of standard-width wallpaper.

Despite the apparent complexity, it is quite possible to do all the work yourself

Disadvantages of wide canvases

Of course, one cannot fail to mention some disadvantages:

1. Difficulties in adjusting the canvas of both vinyl and non-woven wide wallpaper to the adjacent, already pasted canvas, in contrast to traditional analogues.
2. Difficulties with gluing alone. Unlike rolls of regular 53 cm width, working with wide rolls requires an assistant.
3. Necessity better preparation surfaces of the walls before gluing, in order to better fit one sheet to another.

Many of those who are thinking about carrying out repairs with their own hands are interested in how to glue meter-long non-woven wallpaper. However, it is not even so important what material they are made of, since people are interested, first of all, in the features of gluing the canvases large size, that is, how to glue meter-long wallpaper in general, without reference to what they are made of.

However, the raw materials used in production still have a certain significance. However, to begin with, I would like to note that wallpaper 1 meter wide is becoming increasingly popular, despite the fact that they are a fairly new type of finishing coating. According to its structure and general rules When gluing, this material is no different from the more familiar rolls, the width of which is 0.5 meters (or, to be more precise, 53 cm). At the same time, the meter width significantly reduces the time and labor costs for gluing. Today we will talk about how to glue wide wallpaper and what are the features of such gluing.

By the way, if we talk about different countries, then it should be noted that in Europe, the USA and other “far abroad” wallpapers are often sold that have nothing in common with our standards, which were traditionally common in countries former USSR and the current CIS. A width of 0.8 or 1 meter is quite ordinary for them, and no one calls such canvases exclusive or non-standard.

Remember! Wider wallpaper has many advantages, including quick gluing and fewer seams on the walls of the room.

Pros and cons of using

Let's talk in more detail about what advantages and disadvantages this material has. If you are thinking about how to glue meter-long wallpaper on a non-woven basis (however, you can talk about any other canvas, for example, paper or vinyl), then you should consider both positive and negative qualities, which this type of decorative finishing has.

Advantages

1. If you are used to gluing wallpaper using the “butt” method, then you can significantly reduce the number of these very joints, creating an almost seamless effect.
2. The process itself is accelerated, since it is possible to paste meter-wide wallpaper (including on the ceiling and in the corners) much faster.
3. In addition, you can often buy such canvases at a better price (in terms of 1 m2). Affordable cost is an important advantage, especially in cases where the budget for repairs is limited.

Flaws

At the same time, it should be said that gluing meter-long wallpaper is associated with some difficulties, which should also be taken into account:

1. Adjusting the length is quite problematic, especially for those who decided to take up gluing with their own hands for the first time. Sometimes this is the reason that you may end up with some excess material consumption.
2. If you don’t have a trash bin, then you should think about how to hang meter-long wallpaper on your own. The significant size of the canvases (or, to be precise, their width) makes it problematic to stick wide meter-long wallpaper for one person.
3. Before you stick 1 meter wide wallpaper, you will need to carry out more thorough preparation work surface, since these canvases are extremely demanding in terms of wall quality.

How to properly glue meter-long non-woven wallpaper, video:

Step-by-step instruction

So, let's look at the gluing process in more detail, stopping at each stage. Here's how to properly glue meter-long wallpaper.

Preparatory work

1. The first step is to carry out high-quality and thorough preparation of the walls. To do this you need to remove all old Decoration Materials, which could be there, since their remains may interfere with good gluing. By the way, if we're talking about about how to properly glue meter-long non-woven wallpaper, here we should make a little reservation and say that in this case the task is somewhat easier, since in most cases such canvases are quite thick, which, in turn, indicates the possibility of abandoning the ideal preparing the surface, completing this task, so to speak, “with a B.” At the same time, it is advisable to carry out treatments with fairly coarse materials (including coarse-grain sandpaper), since in such cases the wallpaper will stick to the wall better (compared to a perfectly smooth glossy surface).
2. In addition, we must not forget that when carrying out gluing work, it is necessary to tightly close all windows, vents and even ventilation holes to avoid drafts. However, they cannot be opened until they are completely dry. In some cases, it is recommended to dismantle sockets and switches after first disconnecting the electrical wiring in the apartment or house.
3. An important step is the preparation of the glue itself. As a rule, nothing complicated happens, since manufacturers almost always print instructions for preparing the adhesive composition on the packaging. So, even a beginner will not have problems with this. In addition, in most cases, the preparation of the adhesive composition can be done using any available means: you do not have to buy additional accessories or containers.
4. Marking the walls is also a fairly important task. Majority modern wallpaper, especially thick ones (vinyl and non-woven) are glued using the “butt” method. This helps avoid the formation of unsightly seams that occur when using the overlap method. Both for wide meter and for standard wallpaper At least vertical markings should be used. To do this, you need to outline at least one vertical line. For this you can use like building level, and a fairly simple device - a plumb line, which you can easily make with your own hands from literally any thread and weight. You can learn more about the direction of gluing from the article “”.

Sticking

1. When moving on to gluing, you should first cut the wallpaper required length. In cases where you need to match the pattern in adjacent canvases, you will have to leave a fairly large margin. In any case, even if there are no patterns and there is no need to join them, always leave an overlap, both at the top and at the bottom. Its length must be at least 10 cm. On the one hand, this creates, but when great desire you can apply them, or something else.
2. Let's move on to gluing. Before you start applying the adhesive, it is advisable to re-mix it. The good thing about gluing meter-long wallpaper on a non-woven base (not only meter-long wallpaper, but also any other size, including standard ones) is that the glue can only be applied to the wall itself. It is not necessary to coat the back surface of the wallpaper. If you are gluing wallpaper of other types, then you will have to spread the glue both on their surface (of course, with reverse side), and along the wall.
3. Place the wallpaper against the wall. This must be done as carefully as possible. In addition, the first sheet should be glued, focusing on a straight vertical line that you outlined in advance. In order to avoid the appearance of “bubbles”, the pasted wallpaper should be smoothed using a special plastic comb designed specifically for this purpose. This can be bought at almost any hardware store.
4. Having finished with the first sheet, continue gluing the rest using the same technology. Of course, you also need to know how to glue meter-long non-woven wallpaper in the corners. The video or special instructions for this are no different from the principle of gluing standard wallpaper in the corners. Below is a video on how to do it correctly:

Advice! Any excess adhesive released when using a plastic spatula should be disposed of. A dry, clean cloth or sponge will help you with this.

What else needs to be considered

In addition to all the instructions, you must also remember useful tips, which, in any case, it is advisable to take into account before you think about gluing. Here are some recommendations:

• In addition to ensuring there are no drafts, it is worth considering temperature regime was also favorable. This parameter greatly affects the drying of the wallpaper.
• The second tip is related to this: try to complete the gluing before the batteries begin to heat up. The fact is that in those places where there are working batteries, the temperature will be higher, which will affect the uneven drying of the canvases.
• If you are interested in how to glue wide non-woven wallpaper, please note that there are special instructions for each type of canvas. adhesive compositions. Although, on the other hand, some experts fully accept the use of universal adhesives.
• Since the width of meter-long wallpaper significantly exceeds the standard one, when gluing it, it is best to use two stepladders (or 2 stools, if you decide to make do with them). Since you will be working with an assistant, using a couple of stepladders or stools will allow you to place the wallpaper more accurately and level it better.
• By the way, even if you made a mistake when hanging meter-long wallpaper and applied the sheet a little unevenly, this can be corrected. Over a short period of time (maximum 10-15 minutes) you will have the opportunity to straighten the sheet somewhat. This must be done carefully, trying not to tear or damage the wallpaper.
• To make the interior more attractive, you can. By the way, they are also glued end to end. At the same time, make sure that the thickness of the combined sheets is the same.

Drying

Regarding the time during which the wallpaper different types completely dry, then it is, of course, different. For drying vinyl wallpaper, the normal temperature is between 18 and 30 degrees. Of course, in all places in the room it should be the same: if, say, the temperature is 22 degrees in one part of the room, then it should remain at the same level in other corners.

In general, heavier, denser fabric varieties tend to take longer to dry. Some (under certain circumstances) – up to 7 days. As for paper wallpapers, they, being the lightest, dry in no more than three days, and only if we are talking about the so-called “duplex” (two-layer canvases). For simpler, single-layer options, sometimes 20 hours is enough.

Remember! It is better not to try to use certain types of heating, including heat guns, heaters and so on. The wallpaper should dry naturally. This applies not only to how to properly hang meter-long wallpaper on a non-woven base, but also to any other canvas.

Conclusion

In any case, before gluing, it is recommended to watch a video on how to glue wide meter-long wallpaper. Non-woven, vinyl or paper – that’s a separate conversation. Of course, each of these types has its own specific characteristics. From correct gluing not only the durability of operation depends wallpaper covering, but also the attractiveness of the interior of your room, and in general, the entire apartment. Therefore, try to approach the repair with full responsibility and remember that everything is in your hands!