P-44T layout with dimensions
Apartment layouts in P44T with redevelopment options
Layouts of two room apartments series P 44t
Two-piece vest
Usually has an area of about 60-64 sq.m. The kitchen has a large bay window, and each of the rooms has a spacious balcony. In fact, this is the same three-ruble note, only with a “bitten off” eleven-meter room and a section of the corridor adjacent to it.
Linear kopeck piece P-44T
The area of one-sided two-room apartments fluctuates around 52 sq.m. (51-53 sq.m.). They have small corridors and balconies.
One-room apartment P-44 T
The area of one-room apartments in P-44T is about 36-38 sq.m. In them small balcony and a shared bathroom.
Three-room apartments P-44T
In terms of areas and configurations of three-room apartments in the P-44T series, the greatest variation is observed (approximately from 73 to 86 meters). There are also a lot of planning solutions. Kitchens in three-ruble corner sections do not have bay windows, and their area usually does not exceed 10 meters. At the same time, 3-room apartments in row and end sections P-44T boast kitchens with a bay window and a total area of 12 to 14 sq.m.
Three-room apartment with a bay window in the room (end apartment p44t)
Series panel houses P-44T is a new generation of the popular Moscow series of houses. It is the most common modern standard series in Moscow. Bay windows were added to the layouts, the quality improved external finishing buildings has been added attic floor. The series was designed in the mid-1990s. Years of construction: from 1997 to present. In total, about 800 houses were built. The standard service life of a house is 100 years.
At home in Moscow standard series P-44Ts were mainly built in areas of mass development: Izmailovo, Lefortovo, Perovo, Nagatino, Yuzhnoye Chertanovo, Zyuzino, Cheryomushki, Khovrino, Koptevo, Beskudnikovo, Degunino, Sviblovo, Medvedkovo, Yurlovo, Alekseev, Solntsevo, Ochakovo, Kuntsevo, Fili, Shchukino, Zelenograd, as well as on the street. 1905, st. Borisovskie Ponds, and Nizhegorodskaya st.
In the Moscow region, houses of the P-44T series were built in the cities of Zheleznodorozhny, Balashikha, Lobnya, Krasnogorsk, Lyubertsy, Moskovsky, Kotelniki, Reutov, Odintsovo, Khimki, Shcherbinka, as well as in the village. Bear Lakes (Shchelkovsky district), village. Blue and village Brekhovo (Solnechnogorsk district), village. Pykhtino and residential complex "Butovo-Park" (Leninsky district).
All rooms in the apartments of the P-44T series houses are isolated. All apartments have bay windows and spacious loggias. Each entrance has one passenger and one freight-passenger elevator. One-room apartments have combined bathrooms, others have separate ones. The stairs are smoke-free, there is no fire balcony. 
The kitchen stove is electric, natural exhaust ventilation, units in the kitchen and bathroom. Garbage chute on the stairs, with a loading valve on the landing.
The P-44T series of houses differs from its predecessor (series) in increased thermal insulation of the walls, a ventilation duct in the hallway, glazed loggias, bay windows and half-bay windows, as well as recognizable exterior decoration under brick, an attic floor is available for living in houses of the P-44T series.
P-44T, like all other series of the family, was developed specifically for. The first house of the P-44T series was built in 1997 on the street. Marshal Vasilevsky (Shchukino). " Business card"- a multi-storey residential complex on the Rubtsovskaya embankment of the Yauza (project I-1774) built from block sections of the P-44T and series.
Design characteristics and appearance houses of the P-44T standard series are in many ways similar to houses of the series, , .
In 2005, on the basis of the standard P-44T series, a project was developed for standard block sections of the series, where each section has one step less (6 steps), and there are only one- and two-room apartments. Currently, this series is being built more actively within the Moscow Ring Road.
Detailed characteristics of the series
| Entrances | from 1 |
| Number of storeys | from 9 to 25, the most common options are 14, 17. |
| Ceiling height | 2.70 m. |
| Elevators | One passenger (400 kg.) and one cargo-passenger (630 kg.). |
| Balconies | Glazed loggias in all apartments except the first floor. Bay windows and half-bay windows in all two-room and three-room apartments. |
| Apartment per floor | 4 |
| Years of construction | from 1997 to present |
| Built houses | Moscow: about 600, Moscow region: about 200 (including those under construction). |
| Apartment areas | 1-room apartment total: 37-40 m², living: 19 m², kitchen: 7.4-8.4 m² 2-room apartment total: 52-64 m², living: 32-34 m², kitchen: 8.3-13.2 m² 3-room apartment total: 70-84 m², living: 44-54 m², kitchen: 10-13.2 m² |
| Bathrooms | One-room apartments have combined apartments, two- and three-room apartments have separate apartments. Baths: standard |
| Stairs | Smoke-free, with access to a fireproof balcony. |
| Garbage chute | With loading valve on each floor. |
| Ventilation | Natural and forced exhaust, in the kitchen and bathroom. |
| Walls and ceilings | External walls - reinforced concrete three-layer panels 30 cm thick. Internal inter-apartment and interior walls - reinforced concrete panels 16 and 18 cm thick. Gypsum concrete partitions 8 cm. Floors - reinforced concrete slabs 14 cm thick. |
| Load-bearing walls | Longitudinal inter-apartment (as well as inter-room in end apartments) and transverse (inter-apartment, inter-room and inter-balcony). |
| Colors and finishes | Red with sand, bay windows and loggias – white Brick cladding, lower floors – stone cladding |
| Roof type | Flat-pitched with tiles. Technical floor: above the upper residential floor. Possibility of arrangement of an attic apartment. |
| Advantages | Heating appliances with temperature regulators, copper electrical wiring, hot water supply with top spill, fast pace of construction (1st floor in 3 days). |
| Flaws | The quality of installation of individual elements of external walls in some buildings, narrow room in two-room linear apartments (with windows on 1 side) |
| Manufacturer | Moscow house-building plant No. 1 (DSK-1) |
| Designer | MNIITEP (Moscow Research and Design Institute of Typology and Experimental Design) |
These dimensions were taken by me personally in my apartment at the stage of finishing the installation of the house. Regarding the size, it is worth noting that the higher the floor, the larger area apartments as the walls on the upper floors are darker. In my case, the area of the apartment is 0.5 square meters larger than the area specified in the preliminary purchase and sale agreement for the apartment, and this is more pleasant than getting a minus in the area of the apartment located on one of the lower floors.
Now let's move directly to the layout of the apartment and compare it with another offer for a three-room apartment in a building of the 111-M series from the GVSU company. The dimensions of a three-room apartment are presented in the following figure:
Comparison of 3-room apartments of the P-44T and 111-M series
The area of these apartments is almost the same - who likes which one more. This is a matter of taste and needs, but I liked the layout of the P-44T better. Why?
1. Location of the bathroom.
In P44-T the bathroom is located in the corridor near the hallway, and in 111 between two rooms. In the second option, in the rooms near the bathroom you will always hear the noise of water, doors opening and closing, which will disturb the silence in these rooms.
2. Kitchen.
In P44-t and 111-M the kitchens have similar areas, but in the first version the kitchen has a bay window. Thanks to the bay window, there will always be light in the kitchen, and the kitchen will have a more beautiful appearance.
3. Corridor.
In P-44t the corridor is wider and shorter, which will allow installation in it nice closet for not seasonal clothes and other things, and in the 111th the corridor is narrow and long, which does not allow its area to be used profitably.
4 rooms
What I liked about P-44T is that the rooms are wider, which allows for more efficient use of their space, while in 111-M the rooms are quite narrow, which does not allow furniture to be placed on both sides of the rooms. Also in P-44T all rooms different sizes, thanks to this you will have more “maneuvers” in choosing the purposes of each of the three rooms.
5. Balconies
The P-44T has two quite spacious balconies, and in the 111th he is alone. It is worth noting that the cost square meter cold rooms, as a rule, are half lower than residential ones, which means that you pay half as much for balconies and at the same time get more square meters.
6. Ventilatorion boxes
The location of the ventilation ducts in both options is quite good, but note because in P-44t the box is located in the corridor and if the house is higher than 17 floors, then the plus turns into a minus, since a second box appears next to the first and the corridor opposite the bathroom becomes narrow^
If you have any questions, ask them in the comments - I will definitely answer them!
P-44T series
Years of construction: from 1997 to present time
Wall material: panel with brick cladding
Number of sections (entrances): 1-8
Number of floors: 9-25, the most common options are 14, 17
Ceiling height: 2.70-2.75 m.
Elevators: passenger and cargo-passenger, in 20-25-storey sections (entrances) - 2 cargo-passenger and passenger
Balconies: glazed loggias in 1-room apartments. Glazed loggias and bay windows in 2- and 3-room apartments (in end and corner 2- and 3-room apartments there are also half-bay windows)
Number of apartments per floor: 4
Panel houses of the P-44T standard series in Moscow were built both in new areas of mass development: Maryinsky Park, Northern and Southern Butovo, Solntsevo, Mitino, village. Severny, Novokosino, Novoe Kozhukhovo, Nekrasovka, Zhulebino, Lyublino, and in old areas where mass demolition of five-story buildings, dilapidated and uncomfortable housing was/is being carried out: Shchukino, Zelenograd, Khovrino, Beskudnikovo, Koptevo, Sviblovo, Medvedkovo, Izmailovo, Lefortovo, Perovo, Nagatino, Yuzhnoe Chertanovo, Zyuzino, Cheryomushki, Kuntsevo and many others. Also, houses of the P-44T series were built on a spot basis in many areas.
In the Moscow region, new buildings of the P-44T series have been built/are being built in the cities of Balashikha, Zheleznodorozhny, Lobnya, Krasnogorsk, Lyubertsy, Moskovsky, Kotelniki, Reutov, Odintsovo, Khimki, Shcherbinka, as well as in the village. Bear Lakes, village. Blue, village Brekhovo, village Pykhtino.
Number of houses built in Moscow: about 600, in the Moscow region - about 200. This series is one of the most common on the market of new buildings in Moscow and the Moscow region. At the same time, the share of social houses is about 50%.
Standard lifespan of a house(according to the manufacturer - DSK-1) - 100 years
Area of 1-room apartments (4 standard sizes): total: 37-39 sq. m., residential: 19 sq. m., kitchen: 7-8.4 sq. m.
Areas of 2-room apartments (4 standard sizes): total: 51-61 sq. m. m., residential: 30-34 sq. m., kitchen: 8.3-13.2 sq. m.
Areas of 3-room apartments (6 standard sizes): total: 70-84 sq. m., residential: 44-54 sq. m., kitchen: 10-13 sq. m.
All rooms in apartments of houses of the P-44T series are isolated
Bathrooms: in 1-room apartments - combined, in 2- and 3-room apartments - separate, baths: standard, 170 cm long.
Stairs: smoke-free. Garbage chute: with loading valve on each floor
Cooker type: electric
Walls: external reinforced concrete three-layer panels (concrete - polystyrene insulation - concrete) with a total thickness of 30 cm (the thermal insulation of which is equal to brick wall 90 cm thick.) Inter-apartment and interior load-bearing - reinforced concrete panels 16 and 18 cm thick. Partitions - plasterboard 8 cm thick. Ceilings - large-sized ("per room") reinforced concrete slabs 14 cm thick.
Load-bearing walls: longitudinal inter-apartment and transverse all (inter-apartment and interior)
Section type: end, row and rotary (angular). The entrance where the electrical panel is located has an entrance from 2 sides
Number of steps in a section (entrance): 7, step width (distance between two adjacent load-bearing walls): 300 cm (in the 3 central spans of each section), 360 cm (in the rest)
Cladding, plastering of external walls: brick-like cladding, lower floors - stone-like cladding
Color options external walls: dark orange, light red, lower floors - gray, bay windows and half bay windows - white
Roof type: flat-pitched or pitched tiles produced by BRAAS DSK-1, colors: green, brown
Distinctive features: the P-44T series of houses differs from its predecessor - the P-44 series (which was built in 1979-1999) by increased thermal insulation of the walls, a ventilation duct in the hallway (and not in the kitchen), glazing of the loggias, bay windows and half-bay windows, as well as recognizable exterior decoration under the brick
Other advantages: increased sound insulation, heating devices with temperature controllers, copper wiring, technology " closed joint(seam)", world standards for capital strength and fire resistance (1st class), modern system security (response to opening doors of the basement, electrical room, attic, elevator shaft; warning system for flooding, fire). Fast pace of construction (1st floor in 3 days): specialists www.1Dom. ru have not identified a single case of long-term construction of houses of this series.
Flaws: quality of installation of external walls in separate buildings
Manufacturer: DSK-1 (the largest enterprise construction industry Russia)
Designer: MNIITEP (Moscow Research Institute of Typology and Experimental Design)
Structural characteristics and appearance of houses of the P-44T standard series are in many ways similar to houses of the P-44M series,
The first house of the P-44T series was built in 1997 on the street. Marshal Vasilevsky (Shchukino). One of the most recognizable multi-storey stepped residential complex with spiers on Rubtsovskaya embankment in Moscow, shaped like a castle, built from block sections of the P-44T series
- Manufacturer: DSK-1
- Designers: MNIITEP (Moscow Research Institute of Typology and Experimental Design)
The p44t series consists of 14-17-story straight and corner block sections with various options roofs: with mansard end, with flat roof, with “sloping” friezes, which allows you to assemble buildings of different configurations and silhouettes. They can have a height of 9-25 floors. What’s new in the solution for the façades of the series is the combination of panels lined with matte ceramic tiles“brick-like” (bright orange, less often sand-colored), with painted surfaces of bay windows, loggias, cornices and other architectural details. Triangular bay windows are designed at the ends of the sections. The project provides several options for glazing balconies and loggias on the northern facade. The p44t series has become one of the most popular for the construction of municipal housing in Moscow with a construction volume of more than 1 million square meters. m. per year.
The heating, water supply and ventilation systems of houses have been improved compared to the P44 series. The ventilation shaft riser, which in P44 was located in the kitchen, was moved to the corridor in P44T (next to the bathroom and toilet).
The P44T house consists of corner and row sections of four apartments, similar to the basic P44 series. In contrast, in the kitchens of two- and three-room apartments P-44T there are large trapezoidal bay windows. At the same time, kitchens of one-sided two-room apartments, as well as living rooms of end-unit apartments (2 and 3 rooms) have triangular half-bay windows. The area of the apartments has also been increased.
You need to understand that P-44T is, in fact, a group of series - house designs P-44TM or TM-25, as well as P-44K exist and are used, which have a number of differences in apartment layouts, as well as layout typical floors. Moreover, sometimes residential buildings are built, composed of several variants of sections, for example, two P-44T sections and four P-44K sections. There are also other configurations of combinations of sections.
Typical apartment layouts of houses in this series are presented below.
Most often, the first floor is residential. The ceiling height in the house is 2.70 m. Elevators in the house: the passenger elevator has a load capacity of 400 kilograms, and the freight elevator has a load capacity of 630 kg. The building has 20 and 25 floors and has one passenger and two freight elevators (the modification is called P-44T/25).
Glazed loggias start from the second or third floor. A two- or three-room apartment also has eckers and half-eckers. There are four apartments on one floor.
The construction of such houses began in 1997, and are being successfully built today.
Houses of the P-44T type are being built, as in new Moscow large-scale development areas, such as: Nekrasovka, Novoe Kozhukhovo, Zhulebino, Novokosino, Mitino, Lyublino, Maryinsky Park, South and North Butovo, Khodynka and the village. Northern. Construction is also underway in the old Moscow districts, where five-story buildings and dilapidated houses are being demolished, these are: Yuzhnoye Chertanovo, Nagatino, Perovo, Zyuzino, Ochakovo, Solntsevo, Kuntsevo, Cheryomushki, Fili, Khovrino, Beskudnikovo, Koptevo, Degunino, Medvedkovo, Sviblovo, Yurlovo , Izmailovo, Alekseevo, Lefortovo, Zelenograd, Shchukino, st. Nizhegorodskaya, st. 1905, st. Borisov Ponds. Houses of the P-44T type are also being built in other areas of Moscow (including the Central Administrative District).
New P-44T buildings are being built not only in Moscow, but also in the cities of the Moscow region. for example: Balashikha, Zheleznodorozhny, Lyubertsy, Lobnya, Krasnogorsk, Reutov, Moskovsky, Kotelniki, Shcherbinka, Odintsovo, Khimki, in the village of Medvezhye Ozera and the village of Goluboe, also in the village. Pykhtino and village Brekhovo, and also in the Butovo-Park residential complex.
About 600 such houses have been built in Moscow, and in the Moscow region. – about 200 (including those under construction). According to the manufacturer, the service life of such a house is 100 years.
One-room apartment: living area can reach up to 19 square meters. m, kitchen area up to 8.4 sq. m. but not less than 7.4 (in a house with 25 floors, the kitchen is approximately 9 sq. m.), the total area can reach 40 sq. m. m. but not less than 37 sq. m. m.
Two-room apartment: living area can reach up to 34 square meters. m. but not less than 19, kitchen area up to 13.2 sq. m. m. but not less than 8.3 sq. m. (in a house on 25 floors, the kitchen is from 12.8 to 13.8 sq. m.), the total area reaches up to 64 sq. m. m. but not less than 52 sq. m.
Three-room apartment: living area can reach up to 54 square meters. m. but not less than 44 sq. m. m., kitchen area up to 13.2 sq. m. but not less than 10 sq. m., the total area reaches up to 84 sq. m. but not less than 70 sq. m. m.
The rooms in the houses of the P series are 44T, all isolated. Separate bathrooms are made only in two and three-room apartments, V one-room apartment combined bathroom. Bathtubs measuring 1.7 m (standard).
Smoke-free staircases are available in buildings with 20 and 25 floors (type P-44T/25) shared balconies. A waste chute with a loading valve is available on all floors.
Electric kitchen stove. Natural exhaust ventilation and ventilation units in the hallway and bathroom.
External walls: three-layer, 30 cm thick, reinforced concrete panels (the thermal insulation of such walls is equal to 90 cm thick brick, according to the manufacturer). Interior and inter-apartment load-bearing panels are reinforced concrete panels 16 - 18 cm thick. Partitions made of plasterboard 8 cm thick. Large-sized ceilings per room, reinforced concrete slabs 14 cm thick.
Longitudinal inter-apartment load-bearing walls (in end apartments, also interior walls). Transverse load-bearing walls include all walls (between balconies, between apartments and between rooms).
Types of sections: ordinary (in-line, P-44-1), end and corner (rotary). There are two entrances to the entrance with the electrical panel.
Steps in the entrance: seven, the width of one step (a step is the distance between two load-bearing walls) is equal to 300 centimeters (in the three central spans of the section), and 360 centimeters in the remaining sections.
Color options for external walls can be: sand, dark orange and red. The first floors can be: white or gray with a stone finish.
Roofing made of BRAAS DSK1 flat tiles. Above the upper (last) residential floor there is a technical floor.
Distinctive feature houses of type P-44T differ from the more outdated type P-44 (which were built from 1979 to 2000) in: higher thermal insulation, a larger kitchen, due to the removal of the ventilation duct into the corridor, finishing of external walls with brick and bay windows.
Other advantages include: copper wiring, heating appliances with temperature control, first class world standards for capital and fire resistance, supply hot water with top spill, fast construction(floor in three days).
But there are also disadvantages of houses of this series: the quality of installation of some elements of external walls in separate buildings, two-room apartments(linear, with windows in one direction), narrow small room.
In some houses of type P-44T, you can buy an apartment with municipal finishing.
On the street Marshal Vasilevsky in 1997, the first house of the P-44T type was erected. On the Yauza embankment of the Rubtsovsky district, one of the most prominent multi-story houses in Moscow was built from blocks of sections P-44T and P-44M. On the standard basis of the P-44T type, standard blocks were created in 2005 - sections of the type P-44K, where there is one less step in each section (6 steps instead of seven), of course only in one-room and two-room apartments. Today, such types are more actively being built on the Moscow Ring Road.
Below - big photo and layouts of apartments in this series (click on the photo to enlarge and for additional information).
