Option 1. If you first hang wallpaper, then install the ceiling and install masking tape around the perimeter - what happens in the future?
You will want to change the wallpaper without affecting the ceiling. Already problematic.
This option is more suitable for paintable wallpaper, which does not need to be removed over time, but can be tinted or changed color.
Option 2. If you install the ceiling first. That's possible too. Just be careful with sharp objects when gluing.
In this case, the masking tape can be installed only after wallpapering (either on your own or pay for a repeat visit), or you can also glue a foam corner (you cannot glue it to a suspended ceiling).

There are many answers to questions about suspended ceilings here (remove the spaces):
quad-k. rf/poleznoe/vopros-i-otvet....

1 0 0

Decoration of corners with foam plastic frieze (baguette, plinth, molding, decor). The walls are puttied and ready for finishing, the ceilings are ready for painting, but before you start painting, wallpaper and other types of finishing, you should pay attention to the corners, or more precisely, to the corners where the walls and ceilings join. In the distant past, ordinary paper tape with a printed pattern to match the wallpaper (edging). Even earlier, the corners were finished with much more pleasing to the eye plaster rods. But that was a long time ago, and the edges are also poor. Although plaster products on the ceiling and walls are still in use, and such an interior looks gorgeous. But for more than ten years now, foam or polyurethane (more expensive option) friezes have been used to a greater extent to decorate corners. In fact, both are cheap replacements gypsum products. And from an aesthetic point of view, it is not always possible to create plaster rods on ceilings 2.5 m high, and thin friezes...

2 0 0

Home > Walls

On this page you will learn how to properly glue wallpaper with and without a pattern. We will also tell you how to choose and how to calculate the number of rolls of wallpaper, how to glue the frieze smoothly, how to make invisible seams and trimming, answer the question of why wallpaper peels off the wall, how to choose glue...

Calculating the number of rolls of wallpaper is very simple if you follow further recommendations. If the height of your room is 2.5 meters, then from one roll of wallpaper 10 meters long you will get 4 strips of wallpaper without a pattern, each 2.5 meters long. If the wallpaper has a pattern, then at the same height you will get no more than three panels. To calculate the number of rolls, you need to divide the perimeter of your room by 2 meters - if the wallpaper is without a pattern and by 1.5 meters - if the wallpaper is with a pattern. The usual width of wallpaper is about 50 cm. If the wallpaper is without a pattern, then 4 stripes of 50 cm each is two meters, and three stripes of wallpaper with a pattern is...

3 0 0

Gluing non-woven wallpaper - video clip - demonstrates how to properly glue this type of wallpaper.

Before you start wallpapering the walls, you need to check all the rolls for the same manufacturer's number, compare the series, batch number, condition of the packaging itself and the roll, and also pay special attention to the color and pattern of the wallpaper.

All these parameters indicated on the roll must match. Only rolls with manufacturing defects can be returned, and claims related to compensation for losses incurred as a result of work performed will not be accepted.

Applying non-woven wallpaper: a video will help you understand this labor-intensive process, consisting of three stages.

Preparing walls for pasting

The surface of your walls must first be clean before decorating the walls with your own hands. To do this, you will have to carefully remove the old coating, residual glue or paint, as well as various traces of previous markings.

...

4 0 0

How to glue wallpaper correctly

At first glance, it may seem that everyone knows how to glue wallpaper and can easily cope with this work. But when it comes down to it practical actions It turns out that this issue contains many difficulties and nuances that must be taken into account and observed. When starting this work, you need to remember that gluing wallpaper with your own hands is not an easy task and requires strength, patience and some dexterity from a person.

Preparing the walls

First of all, you should thoroughly clean the walls of old wallpaper or other covering. If we are talking about old wallpaper, then you can make your task easier if you first moisten it with water. Paper wallpaper will quickly come off if you moisten it with a soap solution, adding a little wallpaper glue. You can do the same with washable wallpaper, and scratching the layer with sharp and cutting objects will help speed up the soaking process. If the walls were decorated with paint or other materials, then it is necessary to use...

5 0 0

How to properly glue non-woven wallpaper - preparation, gluing, friezes and corners.

In the previous article we examined in detail the features of non-woven wallpaper:

Non-woven wallpaper for painting

Gluing non-woven wallpaper has a number of differences from the process of gluing wallpaper on paper based. As you understand, this is explained characteristic features material used as the main layer - non-woven fabric. In this article you will learn how to properly glue non-woven wallpaper, including the process of surface preparation, wallpaper preparation and direct gluing.

Preliminary control

Having purchased wide, meter or regular non-woven wallpaper, you need to check that the manufacturer's code matches on all rolls. If the code does not match, then your wallpaper is from different series and may differ in shade, albeit slightly. Also, you need to check the condition of the wallpaper, the quality of the pattern, including its coincidence with the photo on the label, and the necessary...

6 0 0

Which wallpaper to choose

The most popular wallpaper today is vinyl. They are durable and quite moisture resistant. Vinyl wallpapers There are several types: from pressed vinyl, foamed and rubberized, on paper and non-woven base. The advantages of the latter are that such wallpapers are easy to glue (the glue is applied only to the wall) and easy to remove (the bottom layer does not remain on the wall). In addition, wallpaper on this basis will help hide minor surface irregularities and small cracks.

For the kitchen and hallway. These rooms are more susceptible to pollution than other rooms. Wallpaper made from pressed or rubberized vinyl is recommended for them. Dirt can be removed from them with a damp cloth, and the wallpaper will remain in excellent condition for a long time.
Any wallpaper is suitable for the living room and bedroom - it all depends on your taste. If you like to change the look of your room often, choose paper wallpaper. They are relatively inexpensive, and will retain a decent appearance for several years, and...

7 0 0

How to glue wallpaper correctly

Using a plumb line, you should align the vertical strip, which will serve as a sample. Focusing on it, you need to stick the first strip.

Wallpaper can be pasted in 2 ways: overlapping or butt. Thick wallpapers are usually pasted end-to-end, otherwise the joints will stand out on the wall, while thin wallpapers can be pasted overlapping.

If you stick plain wallpaper, you should cut the canvas required length. If there is a pattern on the wallpaper, especially a large one, you need to roll out 2 rolls, combine the pattern and then cut it into pieces of the required length.

Apply glue to a piece of wallpaper, then fold it in half and leave for a few minutes so that the wallpaper is well saturated with glue. Then you need to unfold the strip, take it by the top edge, bring it to the wall and attach it to it.

The strip must be glued from top to bottom, and then carefully smooth out wrinkles with a clean cloth or brush from the middle to the side edges. Then exactly the same...

8 0 0

On this page you will learn how to properly glue wallpaper with and without a pattern. We will also tell you about how to choose and how to calculate the number of rolls of wallpaper, how to glue the frieze smoothly, how to make invisible seams and trimming, answer the question of why wallpaper comes off the wall, how to choose glue...

Wallpaper adhesive must match the type of wallpaper. You can find out which glue is suitable for your type of wallpaper from the seller in the store or read it on the glue pack yourself. It is very convenient to glue wallpaper using a special glue with a red indicator from Methylane. When you apply a lot of glue, then on the canvas or on the wall these places will be the most red, and the places where the optimal layer has been applied will be pale pink. Thanks to this, you will not only reduce glue consumption, but also not break the technology, because too much glue is also not good. You can read on the label how to prepare and dilute the glue.

How to glue the frieze evenly.

A crookedly glued frieze, especially if it...

9 0 0

Vinyl wallpaper on a non-woven basis is good for its pearlescent shine and long service life.

General background canvases are often equipped with vertical and horizontal friezes. The variety of assortment allows you to decorate the room in any style. But before gluing non-woven wallpaper, you need to understand the intricacies of the matter.

Non-woven wallpaper is thin. The non-woven base holds the vinyl layer, preventing it from destruction. Under a thin layer of wallpaper, all the errors of the surface being pasted become noticeable. The smallest grains of putty stick out in the form of spikes. Curvature of the walls is not allowed. Otherwise, gaps will appear at the junctions of two canvases

Features of wall preparation

Loose walls are thoroughly washed to remove cement and lime dust. They putty according to all the rules, in two layers: the first with starting putty, the second with finishing putty. You cannot put polystyrene foam into potholes: non-woven wallpaper is laid with pressure during pasting. Everything is thin under the wallpaper...

10 0 0

We created special stripes that can be used to diversify a room. Usually they are glued in rooms where the walls are covered with plain wallpaper or painted in plain colors. They also serve as wall surface dividers. Nowadays they produce a large number of various borders and friezes. They are self-adhesive, with a special layer containing an adhesive composition. They are very convenient to use and easy to operate. There are also borders and carved frieze without an adhesive layer; to operate such borders, you need to purchase an adhesive composition in advance. They are produced in standard rolls, the length of which can vary.
Sticking. Self-adhesive borders and friezes are quite easy to glue. You need to separate the top protective layer from the layer containing the adhesive composition. And then simply apply it to the surface of the wall, press it with both palms and carefully move it along the strip, applying force. This must be done quickly, since the adhesive dries very quickly, and after that...

11 0 0

Do we lay down the linoleum first and then glue the wallpaper, or vice versa?

First wallpaper and then Lenolium

First, wallpaper is glued, and then linoleum is laid, otherwise you will need to clean the linoleum from glue.

Floors in last resort. And if there is already linoleum, then lay the baseboard after you have hung the wallpaper.

We prepare the walls, lay linoleum and work on a clean floor.
The wallpaper needs to be rolled out somewhere.

As you prefer

All Finishing work are conducted from top to bottom.

Let's wallpaper first! then we put linoleum, because there is also a baseboard, and think about what will happen if you do not do it in this sequence...

If the walls are already prepared (that is, puttied and primed), then you can first use linoleum, then wallpaper, and then baseboard.

In any order, and the baseboard last

Tag:

in what order - lay the linoleum and then glue the wallpaper or vice versa, first glue the wallpaper then linoleum or vice versa, tell me if you need a point...

12 0 0

The first thing is to prepare the walls: peel off the old wallpaper (put it in a spray bottle hot water With detergent for dishes, spray the walls, let them sit and easily peel off), then putty all the holes and cracks in the walls, let the putty dry. Then carefully sand the uneven spots on the repaired cracks. The next stage is priming the walls - you can use commercial acrylic or buy cheap wallpaper glue, dilute it thinner and treat the walls, let it dry, you can prime it up to 2 times for better adhesion. This is actually a classic preparation, then let’s move on to the wallpaper. What kind of wallpaper do you have - paper, vinyl on a paper backing or vinyl on non-woven fabric. Everyone sticks differently .Glue thin paper - hemorrhoids, it is better to take foam or duplex. If there is a fit, cut out identical pieces and go, apply glue only to the wallpaper. Next, vinyl on paper is heavy wallpaper, you apply both wallpaper and the wall, vinyl on non-woven fabric can be adjusted directly to wall, just apply the wallpaper to the wall dry. Actually for all types of wallpaper...

13 0 0

All wallpaper is now glued end to end. We need to prepare the walls. If the walls are visually aligned, the corners and junctions in the floor and ceiling should still be level.

Measure the wall from the last sheet of wallpaper pasted to the corner. Cut the dry sheet to measure. Peck the sheet. The corner should be covered with wallpaper; use a spatula to press the wallpaper very tightly into the corner. Take the other half of the cut sheet and glue it overlapping in the corner to the next wall. And also press it very well in the corner. Then take a wide metal spatula and a very sharp wallpaper knife and carefully cut both layers of wallpaper along the spatula. Remove any scraps from both sheets. The wallpaper will lie end to end and the pattern...

14 0 0

How to glue wallpaper correctly Helpful tips Answers how?

What is the procedure for wallpapering walls? Let's study the process. If you decide to glue wallpaper correctly, follow the technology. Newspapers on. A person of any gender should know how to hang wallpaper correctly. Despite the fact that many consider any repair work purely masculine, you could often see how women are hired to paint or wallpaper an apartment. A site about renovations, how to level walls, how to choose wallpaper, what types of wallpaper there are, how to hang wallpaper correctly. If you want to glue the wallpaper well, be sure to apply glue to the corners and walls near the baseboard and ceiling. How to properly glue wallpaper, thick wallpaper, thin wallpaper Fillet, or how to properly glue the ceiling. both on wallpaper and on the wall. How to properly glue wallpaper is not an idle question, because the overall impression of your interior largely depends on the wallpaper - see the technology.

How to glue wallpaper correctly? How to glue wallpaper correctly? How...

15 0 0

How to properly prepare a surface for wallpapering

First you need to remove the sockets and switches that protrude outward. In addition, you need to remove dowels, screws, and nails.

If the wall was painted with lime or adhesive paint, then it needs to be washed away warm water using soap and then remove with a spatula.

Cracks in the walls are widened, moistened with water and covered with a solution or a mixture of chalk and gypsum (3:1), then putty. The walls must dry out. The putty areas must then be sanded.

The finished surface for wallpaper must be clean, dry, smooth and strong. Mold must be treated with an antiseptic.

Remove old wallpaper with a rag or brush after soaking it with warm water. If the main part of the old wallpaper is held too tightly, you can remove only the swollen or peeled fragments. And to avoid depressions, the cleaned areas are covered with paper.

Oil-based (enamel) paint does not need to be removed. But it is necessary...

16 0 0

Decoration of corners with foam plastic frieze (baguette, plinth, molding, decor). The walls are puttied and ready for finishing, the ceilings are ready for painting, but before you start painting, wallpaper and other types of finishing, you should pay attention to the corners, or more precisely, to the corners where the walls and ceilings join. In the distant past, ordinary paper tape with a pattern applied to match the wallpaper (edging) was used to decorate this part of the room. Even earlier, the corners were finished with much more pleasing to the eye plaster rods. But that was a long time ago, and the edges are also poor. Although plaster products on the ceiling and walls are still in use, and such an interior looks gorgeous. But for more than ten years now, foam or polyurethane (more expensive option) friezes have been used to a greater extent to decorate corners. In fact, both are cheap replacements for gypsum products. And from an aesthetic point of view, it’s not always possible to fulfill...

17 0 0

View full version: Question about working with fiberglass "gossamer"

Pages: 1 2 3 4 5 7 8

17.05.2013, 15:07

I puttyed it with vetonite, glued fiberglass, glued the plinth on it and puttyed it with shitrok, will it work out?

Ars Di Col

17.05.2013, 15:11

vinni-pux glue the skirting board onto the sheetrock, it will hide any unevenness on the wall, which is unnecessary to wash with a brush. We don’t glue cobwebs, we glue glass canvas onto an already prepared wall, which we paint without putting putty.

17.05.2013, 15:12

Shitroka can hardly stick to uniflot

Ars Di Col

17.05.2013, 15:17

vinni-pux Uniflot plaster - will not stick. To be honest, you don’t need much, the very edge is coated on both sides, not very thick - 5 mm. They glued it, looked at it from the side, where the unevenness was, pushed a little putty there, washed it with a brush and that’s it.
399491 399492 399493 399494 399495 399496 399497

Can"t find the video you want? This page will help you find the video for your mood. Enter your search query in the search bar and you will get relevant results. We can easily find any video for any direction. Whether it"s news or jokes, or maybe a movie trailer or a new sound clip?

If you are interested in the news, then we will offer videos from eyewitnesses, let it be a frightening incident or a joyful event. Or maybe you are looking for the results of football matches or global, global problems. We will always bring you up to date if you use the search on our website. The quality and useful information in the video clip does not depend on us, but on users who have downloaded the videos on the Internet. We only offer videos for your search query. But in any case, you will find the information you need if you use the search on the site.

The world economy is an interesting topic, it excites many people, regardless of age or country of residence. Much depends on the economic condition of the country. Import and export of products or equipment. For example, a person’s standard of living may depend on the state of the country, salary, services, etc. Why would you ask such information to you? She can warn against the danger of traveling to another country, or find out better the country in which you are going to go on vacation or move to a permanent place of residence. If you are a tourist or traveler then it will be useful for you to watch a video on your route. It can be either a plane flight or a hiking trip to tourist areas. It is better for you to learn in advance about the traditions of a new country or about a tourist route where predatory animals or poisonous snakes can meet.

In the 21st century, it is difficult to discern officials in the political views; to understand the general picture of what is happening, you better find and compare information yourself. A search will help you find officials" speeches and their statements for all times. You can easily understand the views of the current government and the situation in the country. You can easily prepare and adapt to future changes in the country. And if elections are held, you can easily evaluate the official's speech several years ago and now.

But here is not only the news of the whole world. You can easily find yourself a suitable movie that will relax you in the evening after a hard working day. Do not forget to bring popcorn! Our site contains films of all time, in any language, any country, and with actors from all over the world. You can easily find even the oldest films. Let it be an old Soviet cinema, or a movie from India. Or maybe you are looking for a documentary, science fiction? Then you will find him very soon in the search.

And if you want to relax and watch jokes, fails or funny moments from life. You will find a huge number of entertainment videos in any language of the world. Let it be short films or full-length pictures with humor for every taste. We will charge you with a cheerful mood for the whole day!

We collect a huge database of video content for each person, regardless of country of residence, language or orientation. And we hope that you will not be disappointed and find the necessary video material to your taste. Creating a convenient search, we took into account all the moments that you were satisfied.

Also, you can always find music in absolutely any direction. Let it be rap or rock, or maybe even a chanson, but you will not remain in silence and you can listen to and download your favorite audio clips. If you are going on a trip, then our site will help you find your favorite collection of music that you can download and listen to while traveling. Our site will help you out even when you do not have internet!

Nowadays it is almost impossible to find premises without finishing with ceiling plinths. This plinth gives the design of the room a complete, finished look. In this article we will look at how to glue ceiling plinth for wallpaper and putty.

Ceiling plinth is a product made of urethane foam or polystyrene foam; it is also called fillet, baguette, frieze. With the help of this product it is quite easy to hide small irregularities in the wall during finishing or repair.

Tools

To work with baguette you will need the following tools:

• roulette;
• a simple pencil;
• stationery knife;
• miter box;

• square;
• sealant;
• putty knife;
• file with blade for metal.

In addition to having all the tools, it’s also a good idea to have basic skills in working with them, which will allow you to get the job done quickly and efficiently.

Material selection

Before starting work with the design, you must also correctly calculate its quantity. There is absolutely no need to take extra, although the price is not too high.

Note!
Usually all fillets are sold in lengths of 2 m.
This information will allow you to correctly calculate required quantity fillets.

The calculation is done like this:

• using a tape measure, measure the perimeter of the room in meters;
• the result obtained is divided by 2;
• the total is rounded up and is the final number of fillets.

For example, the perimeter of the room was 22 m. Then you need 22/2 = 11 pieces. If you don’t have the skills to work with friezes, then it’s better to take a little more, for example 12-13 pieces.

On construction market You can find a huge variety of fillets, both in design and width. should not be used in rooms with low ceilings, so as not to further visually lower the ceiling. For example, for ceilings with a height of about 2.75 m the best option is a fillet with a width of about 45 mm.

Note!
When buying fillets with a large number of embossed parts, you will have to wipe dust off them quite often.
Almost smooth skirting boards require much less attention.

Which side to glue the ceiling plinth depends on both the size of the room and the type of finish. Fillets may have different sides, when viewed in cross section.

It is common to do this:

• in large rooms with high ceilings, glue the baguette with the wide side facing the ceiling;
• in small rooms with low ceilings - the wide side to the wall.

However, there are exceptions to all rules. So, if during the process of wallpapering it turns out that there is a large gap between the ceiling and the walls, then it can be hidden by gluing the frieze with the wide side to the wall.

Everyone decides for themselves what glue to use to glue the ceiling plinth.

The following are usually used as fasteners:

• adhesive for ceiling plinth “Moment Montazh”;
• glue "Titan";
• white acrylic sealant.

Mounting options

All installation work begins from the corner of the room.

During repairs, 2 installation options are used:

1. attach the ceiling frieze on top of the wallpaper;
2. attach the ceiling frieze before wallpapering.

Note!
Usually baguettes are sold in white color, so in order not to stain them with your hands, be sure to wash your hands with soap before working.

Paste on wallpaper

This method is used to fix the frieze on walls covered with wallpaper.

The order of work is as follows:

• apply thin layer glue on the surface of the frieze adjacent to the wall and ceiling;
• apply the frieze to the wall;
• stand for as long as indicated on the instructions for the glue;
• remove excess glue using a clean rag or sponge;
• seal all joints with white sealant;
• if necessary, paint the entire surface with water-based or acrylic paint.

Note!
When painting the frieze, you need to be especially careful so as not to damage the wallpaper.
It is best to paint it before installation.

The main advantage of this method is that there is no need to adjust the wallpaper to the frieze. It will hide all possible burrs, as well as distortions of the wallpaper in the upper part.

We attach the baguette before wallpapering

This option occurs quite often. Many professionals prefer it.

The work order is as follows:

• carefully prepare the walls and ceiling, level the surfaces using putty;
• the ends are trimmed using a miter box;
• attach the baguette using the same putty or drywall glue;
• fill all the gaps between the moldings, walls and ceiling with putty;
• remove excess putty using a clean rag;
• work stops until completely dry putties;
• prime the entire surface;
• painted in the desired color;
• wallpaper is glued, and the overlap in the upper part is removed by applying a spatula and cutting with a stationery knife.

Note!
By painting the baguette in the same color as the ceiling you can get visual effect a single monolithic structure.

The main advantage of this method is that it is easy to paint the frieze at the installation site and defects can be easily corrected without fear of deforming the wallpaper.

Angles

The most difficult and painstaking work Installation of ceiling plinth involves preparing corners and joints.

To complete this work you will need the following tools and materials:

• small spatula;
• putty or sealant;
• container for putty;
• miter box;
• a stationery knife or hacksaw with a metal blade.

Note!
Fitting the finishing strip should begin by cutting out the corner.
This will avoid damage to the material in case of an error with the angle.

Instructions for cutting the required corners:

• if you have no experience in this matter at all, then it is better to practice on small pieces of fillet;
• place the bar in the miter box the way it will hang on the wall;
• the lower part of the baguette is pressed tightly against the wall of the miter box;

• cut the end at the desired angle using a knife or saw, while avoiding pressing hard on the surface of the baguette so as not to crumble it. Usually an angle of 45 0 is selected;
• apply the cut edges to each other, checking that there are no gaps;
• if necessary, cut off the interfering parts with a knife;
• apply the fillets to the installation site, making the final adjustment;
• begin installation.

Note!
Ready-made external and internal corners for baguette of almost any design.

How to glue the corners of the ceiling plinth is usually indicated on their label. They are glued in the same way as the profile itself.

Preparing corners without a miter box requires a little experience and patience. Many professionals use stencils for this, applying rough cardboard to a corner on the wall.

Conclusion

From this article you learned how to glue ceiling plinth to putty and wallpaper correctly. Like many other types of work, frieze installation has some features that should be remembered, especially if you plan to do the repairs yourself.

The best way to complete the ceiling is to use special skirting boards. These products are glued around the perimeter of the room at the junction between the ceiling and walls.

How to choose a baguette

Corner areas where wall and ceiling surfaces intersect require beautiful design. Decorative ceiling plinths were developed especially for this purpose. The fillet looks like a plank 1.2-2 m long, for the manufacture of which polyurethane, wood, gypsum or foam are used. Regardless of what material the frieze is made of, a similar scheme is used on how to properly glue the ceiling plinth.

Arriving at a hardware store, the first thing you need to do is decide on the material for making the ceiling plinth. The cheapest ones are foam and polyurethane products. In addition, they are lightweight and very easy to install. Externally, these varieties are almost impossible to distinguish, because have a polymer base. However, the quality of foam planks is slightly lower. Polyurethane skirting has great weight and elasticity.

You should also find out the amount of consumables. This is done by simply measuring the perimeter of the room where the renovation is being carried out. Some people confuse perimeter with area. So, if the dimensions of a room are 3x4 m, then to calculate its perimeter the following formula is used: (3+4)x2m = 14 m. If the choice fell on friezes 2 m long (this size is most common), then to decorate the room you will need 14: 2=7 baguette. Considering the cost of cutting corners, they always take one more product into stock.

Another important point on how to properly glue skirting boards to the ceiling is the width of the frieze. As practice shows, low ceilings It is advisable not to decorate with wide baguettes, because this will lower the room even more. Therefore, the higher the ceilings, the wider the baguettes you need to take. It is believed that the suitable width of baguettes for standard ceilings in apartments (2.5 m) is 4-6 cm. As for the decorative design of the planks, plain walls They will look much more interesting if you use friezes with a pattern or texture. It is better to complement wallpaper with ornaments with absolutely smooth baseboards. You also need to know what to glue the wallpaper or ceiling plinth first to avoid possible problems.

Which glue is better

Before gluing ceiling skirting boards, you need to choose high-quality glue. It’s better to figure out from the beginning what is the best way to glue the ceiling plinth so that there are no problems later.

Specialized departments offer the following types of glue for gluing ceiling skirting boards:

1. Acrylic. The main substance here is water, so this substance does not smell. This inexpensive composition for gluing skirting boards to the ceiling is recommended for use in rooms with a normal microclimate: it does not withstand direct contact with moisture.
2. Polymeric. This glue is characterized by strength and moisture resistance. The substance contains chemical solvents that maintain its liquid consistency. Polymer glue dries for quite a long time (several days), emitting a specific odor throughout this period. Despite significant shortcomings, this particular composition is most popular among consumers. We are talking about such famous brands, like "Titan" or "Moment". Their distinctive feature is reliability and versatility. Within the line of polymer compositions, there may be differences in the speed of setting and the degree of resistance to low temperatures.

When choosing between polymer and acrylic glue for gluing ceiling plinths, take into account functional purpose premises. In children's rooms it is better to use a safe acrylic variety. It is recommended to decorate the kitchen and bathroom with a moisture-resistant polymer substance. You can find special glue for working with wet parts. There are also quick-drying compounds that are very convenient when working at heights. To fix wooden baguettes, you can use not only glue, but also screws and nails.

Homemade compositions

To glue the ceiling plinth, it is not at all necessary to spend money on purchasing glue. If we are talking about a baguette made of plaster or foam plastic, you can prepare the mastic for its installation yourself. The finished mixture can also be used as a putty for joint areas and gaps between individual planks and in places where they adjoin walls and ceilings.

Homemade glue recipe:

• For cooking you will need water (1 part), finishing putty(1 part), PVA glue (1/4 part).
• The ingredients are placed in a plastic bucket and mixed thoroughly until a homogeneous mass is obtained (like thick sour cream). The substance must not contain lumps or clots. After preparation, the composition is left to stand for several minutes.
• Before properly gluing the baseboards, the substance is mixed again.

The finished mixture can be used both as glue and putty. Since its basis is water, its characteristics homemade material very similar to factory acrylic glue. It is better not to use it in very damp rooms.

Preparatory activities

After purchasing the friezes, you need to print them out and bring them into the room where installation will take place for a day. The most difficult moment in the technology of how to glue the ceiling plinth is joining the friezes in the corner areas. To do this, the planks need to be cut obliquely at an angle of 45 degrees.

Available for sale special device– a miter box in which there are special guides for a knife or saw at the desired angle. Typically, a miter box is equipped with several slots at different angles (90, 45, 60 and 67.5 degrees). To cut the bar, it is placed in seat opposite the 45 degree cutout. A sharp knife is usually used as the cutting material. The ends of the cut must be smoothed upon completion of the operation. It is recommended to cut the corners first, and only then adjust the product according to the footage.

The fact is that in case of an error with cutting a corner, the cutting location has to be shifted, which conceals the length of the strip. As a result, an unsightly gap forms at the junction with another element. Especially to simplify the procedure for gluing fillets, there are decorative corners, which are used to mark the joints of the baguette.

Before gluing the ceiling plinth, the ceiling surface is thoroughly prepared. It must be dry and clean before starting work. Wooden and plastic bases must be cleaned of grease stains. Concrete and plasterboard floors are puttied several times, achieving their ideal evenness. This also applies to walls. If the ceiling and walls are smooth, this will ensure ease of installation of the baguettes: the areas where they are adjacent to the wall and ceiling will then be almost invisible. After the putty has dried, it is sanded with fine sandpaper.

Installation work

The ceiling plinth can be installed after wallpapering or during the process of screeding the ceiling (before the last putty).

The second option, how to properly glue ceiling skirting boards, provides a number of advantages:

1. When re-gluing wallpaper, you will not need to tear off the baguettes. In this case, the stripes will be adjacent to the friezes, and not go under them.
2. Glue the baseboard to uneven ceiling, as a rule, much more difficult. If the walls are made unevenly, gluing baguettes after the wallpaper will certainly lead to the appearance of gaps between the planks and the plane of the walls. In the second case, all noticed cracks are carefully sealed with a mounting mixture, without the threat of staining the wallpaper.

It is recommended to start work from the corner near the window: it is more convenient to immediately glue the frieze to both walls in order to achieve the formation of a beautiful corner joint. The smoother the corner of the room is plastered, the easier it will be to decorate it with a ceiling plinth. The resulting structure of two baguettes will set a guideline for further work. You can choose any wall and start adding moldings towards the next corner.

How to glue on suspended ceilings

Decorative lighting

To obtain the original lighting effect of the baseboards, special translucent plastic baguettes are used. They are mounted in exactly the same way as regular ones. The main thing is to first lay the appropriate wiring around the perimeter. Most often, LEDs are used for these purposes. The plinth must be mounted in such a way that the glue is located exclusively on the wall: it is important to leave it between the baguette and ceiling surface small gap.

Correct technology for fixing ceiling plinths

To properly glue the ceiling plinth, as professionals say, you need to follow the following recommendations:

• Store-bought or homemade compounds can be used as glue. In the latter case, it is advisable to use the same putty to prepare the glue as for the ceiling screed.
• Sometimes various communications are laid under the baguette. This must be done in advance. If we are talking about wiring for decorative lighting, the baguette needs to be attached only to the wall. To prevent the wires from interfering with the tight fit of the baguettes, it is recommended to make a recess.
• The gluing of skirting boards to the ceiling is carried out at a height, so you need to think about it in advance convenient device for this. An old kitchen table or construction goat comfortable height. The use of stepladders is not recommended, as they do not provide enough room for maneuver.
• When starting installation, the fastening areas are moistened with a primer or water: this will prevent the glue from drying out quickly. Homemade or store-bought glue is applied in a thin strip to the back of the baguette (there is usually a special recess there), using a small spatula. Corner areas need to be coated especially carefully.
• The plinth is placed tightly between the wall and the ceiling. After pressing firmly, you need to pick up the protruding glue with your finger or spatula. Particles that fall on the surface of the molding are removed with a damp cloth or sponge. The joints are coated with the mounting mixture and washed away with a soft brush.
• Using store-bought glue speeds up the procedure somewhat, as it hardens much faster. However, there are also some difficulties - it is impossible to seal cracks and joints with this composition: you have to prepare a little putty.

• To ensure that the plinth lies flat on the wall, it is recommended to make markings first. The broken lines will indicate the lower and upper border of the bar.
• It is easiest to join friezes that do not have a complex pattern. However, there are expensive products that imitate stucco: in order to harmoniously connect the curls on adjacent parts, you have to be extremely careful.
• Correctly gluing skirting boards to the ceiling, as a rule, good adhesion helps adhesive composition with walls and ceiling. They must be thoroughly cleaned from dirt and dust.
• The gluing of polystyrene foam and polyurethane baseboards can be done one after the other, because These lightweight products hold up well. As for wooden and plastic products, then a short pause is often required for the adhesive to set. To avoid downtime, the planks are usually installed alternately at one and the other end of the corner.
• As you work, your hands gradually become smeared with putty, so they need to be washed periodically. If a trace of dirty fingers remains on the surface of the baguette, wash it off with a wet sponge.
• To remove excess protruding when pressing on the baseboard, you can use a spatula or a dry sponge.

Design of joints

Painting

The final procedure for installing the ceiling plinth is painting: it gives the ceiling a finished look. beautiful view. Most often, water-based, acrylic or latex paints are used for this. Wooden products are decorated with nitro paint, after having been coated with a primer. Before painting the friezes, they need to be allowed to dry: usually a day is enough for this. Acrylic or water-based compositions demonstrate the greatest practicality. For application, a soft brush of appropriate width is usually used. It is most convenient to paint baguettes together with the ceiling, using identical material. Wallpapering or other types of wall decoration can be done after the paint has dried.

Bottom line

Installation of ceiling plinths is one of those simple activities that you can implement on your own. Before gluing the ceiling plinth to the ceiling, it is recommended to pay special attention to the quality alignment of the walls and ceiling.

The concept of quality repairs is changing at lightning speed with the birth of new design elements and ideas. In the recent past, neatly pasted wallpaper in combination with the correct edging, which was multi-colored paper strips, and sometimes even an ordinary tape, was considered the height of skill.

It is impossible to imagine the modern decoration of an apartment without baguette decoration. After all, the correct, harmonious combination of a structure from two planes is the key to the beauty and comfort of the room. Let us dwell in detail on how to properly glue baguettes so that the finish looks exemplary.

Properties and features of baguettes

The use of such decorative elements has a number of significant advantages:

• excellent masking of small defects in ceilings and walls, such as differences, roughness and unevenness;
• decoration of the junction of two surfaces;
• simple installation that does not require professional skills;
• lightness and flexibility of the material;
• large selection of designs;
• saving money due to reasonable prices.

Advice! Before choosing baguettes for the ceiling, you should consider that they can be made from different materials, be of different textures, widths, have a smooth or patterned surface. These qualities affect not only their cost, but also their purpose and differences in application for a variety of interiors.

Baguette, also called molding, ceiling plinth or frieze, is made from the following materials:

• polyurethane;
• polystyrene foam;
• plastic;
• gypsum;
• tree.

In most cases, polyurethane and foam baguettes are used. Plastic molding is used only under stretch ceilings, wooden - in connection with the same ceilings.

Choosing the right glue

Every experienced master To install the frieze, he uses his own proven adhesive composition. Such means may be:

• polymer;
• acrylic.

Polymeric the composition is characterized by low stickiness. In order to reliably fix the molding with such glue, it must be held in the desired position for quite a long time, and this is not entirely easy to achieve for a two-meter part.

On silicone And acrylic glue to install the frieze quickly and comfortably. Manufacturers package them in gun tubes. The product is applied with ease, and the diameter of the release hole at the tip controls its consumption.

The procedure for gluing a baguette with silicone and acrylic compounds is usually described in the instructions for the material. Negative side Such funds can be called their high price.

The most budget-friendly way to glue baguettes on your own is the traditional finishing putty or composition for drywall, if it is used in decoration. This mixture is reliable, it takes less time to harden, so after half an hour you can already paint the ceiling and baguettes.

However, there are also disadvantages to using putty as glue:

• the inconvenience of applying a thin layer of the mixture with a spatula on the molding;
• Upon completion of gluing, excess putty or plasterboard glue will need to be thoroughly removed with a dampened brush. Otherwise, pieces of visible dry mixture will spoil the picture.

How to glue baguettes to the ceiling

There are two options for attaching the ceiling plinth:

• on the surface of the wallpaper;
• before wallpapering.

As a rule, baguettes are pure white, therefore, in order not to contaminate the products, you should thoroughly wash your hands with soap before starting work.

Advice! To start installing baguettes, you can choose any corner of the room.

You should know some of the features of gluing ceiling skirting boards:

1. Much attention should be paid to cleaning the wall and ceiling from traces of adhesive. Acrylic and silicone based products can be removed using a rubber spatula and a damp cloth. It is recommended to remove excess putty with a small wet brush.
2. It is necessary to fill all the cracks around the molding with glue. You should also process corner connections. Don't rely on painting or wallpapering to hide these gaps. This won't happen. Any glue that gets on the wall or ceiling should be carefully removed.
3. Often, when the glue hardens at the joints, the end of the baguette comes off, and you get a step. To protect against this effect, two adjacent ends must be fixed in the required position with sewing needles or pins. When the glue hardens, the needles must be removed and the holes covered with an adhesive mixture.
4. Several layers of paint are applied to the baguettes. First, priming is performed to mask the putty joints. Then they apply layers that play a decorative role, and at the same time paint the ceiling.
5. Excess glue along the baseboard should be cut off with a sharp spatula.

Sticking baguettes on wallpaper

The obvious advantage of this method is that there is no need to adjust the wallpaper to fit the baguette. The frieze will cover all the errors along the upper edge of the finish.

Procedure:

1. Trim the ends using a miter box.
2. Apply a thin layer of glue to the glued surfaces of the baseboard.
3. Place the plank against the wall and hold it in place, according to the instructions for the glue.
4. Remove excess material with a sponge or rag.
5. Seal the joint gaps with white sealant.
6. To paint the baguette, use acrylic or water-emulsion paint.

Advice! To avoid staining the wallpaper when coloring the baseboard, lay masking tape along the baguette, and after the paint has dried, remove the protection.

How to secure a baguette before wallpapering

This is a professional method that is performed in the following order:

1. Prepare the walls and ceiling. Get rid of roughness and unevenness with sandpaper, remove construction dust from the surface, then cover with a primer mixture.
2. Trim the ends of the plinth using a miter box.
3. Secure the baguette with putty or plasterboard glue.
4. Fill all cracks with putty, remove excess with a clean rag.
5. Wait for the putty to harden.
6. Prime the surfaces.
7. Paint the ceiling and moldings.
8. Put up wallpaper. Cut the top overlap onto the baseboard evenly with a sharp knife using a wide spatula.

The advantage of this method is the ease of correcting adhesive defects and the ability to paint the installed baguette without fear of staining the wallpaper.

Features of installing baguette in corners

The last plank must be adjusted with a corner cut out to prevent damage to the material when an error with the angle is detected.

If the room has even angles (90 degrees), then the angles between the two walls and between the ceiling and the wall should be straight. In this case, it is possible to correctly cut out the corners using a miter box.

First you need to trim the corner baguettes using a miter box. Then bring their ends to the required size with a sharp knife. Distribute the gaps evenly across both sections to prevent a step effect.

Procedure for using a carpenter's miter box:

1. If you have no experience in this kind of work, we recommend practicing on small pieces of frieze.
2. Place the bar in the miter box as it will be on the ceiling.
3. Press the lower part of the frieze tightly against the side of the miter box.

If there is no miter box, you can trim in this way:

1. Attach the frieze to the corner on the left side.
2. On the ceiling from the corner, draw a segment (10-15 cm) along the baseboard with a pencil.
3. Do the same steps on the right side of the corner.
4. Where the lines intersect is the starting point of the cut.
5. On the left and right strips, mark the intersection of the segments.
6. From the mark to the opposite side of the left and right frieze, cut evenly with a construction blade at an angle of 45 degrees.
7. Check that the cutting is correct by placing the processed friezes against the corner.

As you have seen, there is nothing complicated about gluing baguettes. Guided by our advice, you will successfully complete this job.