After laying the laminate, the floor rose 2 cm, and one of the doors needed to be sawed down 1-1.5 cm from below.
Interior door, simple laminated, covered with MDF. Corrugated inside.
What could be used to file the door so that:
1) it was smooth
2) there were no chips or “brush” effect on the saw cut.
Cover the cut with masking tape.
Sawing with what? Drag it to any format. (saw for cutting sheet materials) Available in all large construction shopping centers and carpentry factories. Don't even try using a jigsaw or hacksaw. In theory, it can be cut off circular saw"frog", but you need very straight hands.
Do you have any similar experience? I just don’t think that the shopping center will be happy if I bring them a door and say that it would be necessary to cut it off by 1-1.5 cm. I didn’t cut it in the shopping center, but I sawed off a lot of doors at a friendly production facility.
I sawed with an electric jigsaw, having previously wrapped it in masking tape. It doesn’t turn out very nicely, but if you don’t crawl along the floor with a ruler, it won’t be noticeable. How much did you saw off? What's inside at this height?
This is if you cut along a line, but if you run a jigsaw along the guide, then the file will be thin and will lead vertically. I sawed 16 mm as hard as I tried, the line is straight, but the vertical is moving. But the idea with the router is the best idea of all.
Nope, it won't. There will be a “four” on plywood. On a 40 mm door leaf - no. With a circular saw - most likely it will work. Along the guide bar.
At Stroy Arsenal, they will most likely undertake to cut it off, and the price tag will be ridiculous. I brought them 32mm chipboard to cut. They took it at the rate of 35 rubles. for the detail. They can take the same amount out the door.
Usually the canvas is no thicker than 40 mm. That's exactly what the guy who was installing another door said.
Yes, the blade is 40 mm. Just sawing the door is a responsible task :-D And the opening was foamed, covered with platbands and no jambs are visible.
If the block is 5 cm, but you need to saw off 2 cm, then there is no problem - use a jigsaw and go ahead (adhesive tape for the “beard”).
But if you are afraid that you need to saw off more than the width of the bar (you will hit the compartment with the corrugation), then it is better to take it to those who have special equipment!
Moreover, if you cut without a guide bar, the blade will move less vertically. Because it is possible to press the jigsaw slightly left and right and control the blade (do not unfold it, but press horizontally)
With a block, the canvas moves much more precisely, even to the point of breaking if you overdo it.
You've inflated the topic! Normally these doors can be sawed with a hacksaw. and.a jigsaw!!! :-D
In such cases, it is most rational to use primed panel doors with fiberboard linings. Such a door leaf can be purchased for $15-20. After trimming and additional processing The canvas is painted and in appearance is almost no different from the standard canvas.
With fiberboard overlays it allows you to quickly, easily and practically without damage to appearance trim the door leaf from the top, bottom or side.
Work technology:
1. To reduce the width or height of the door leaf to 0.5 cm
can be used:
- Jointer. Gives best result, but not everyone has such a machine;
- Electric jointer. It gives a good result, but is also rare on the farm;
- Electric planer. It gives a good result, but you need to work carefully, because in the end, if you don’t hold the plane, it often chooses an unnecessary recess;
- An ordinary plane or jointer. If the height of the door decreases, then the pillar bars need to be shortened with a circular saw, hacksaw or jigsaw.
2. To reduce the width or height of the door leaf by 0.5-1 cm
can be used:
- Circular machine. It gives the best result, but again, not everyone has such a machine;
- Hand-held circular saw. It gives a good result, but is also rare on the farm;
- Jigsaw. Almost never the cut turns out smooth and therefore the canvas needs to be additionally planed, so you need to cut with a small margin;
- Hand saw (hacksaw). The cut turns out to be more or less even, but often not perpendicular to the planes of the blade and therefore the blade needs to be additionally planed, so you need to cut with a small margin.
After cutting, the ends of the door are processed by grinding. It is advisable to chamfer the fiberboard canvas in the cutting areas (slightly round the ends). This is best done by hand, using sandpaper attached to an iron or plastic grater.
Note: when reducing the width of the door, it is advisable to cut the door on the side where the lock will cut in, and not on the side where the awnings will be installed.
3a. To reduce the width or height of the door leaf by 1-3 cm
You will need to first disassemble the door and use glue to strengthen the door structure. The success of disassembly depends on the quality of the glue. Try using a wide chisel to separate the fiberboard panel from the wooden block of the frame in the place where the fiberboard will be cut. If the canvas separates easily enough and does not collapse, carefully release the frame block, remove the metal staples holding the frame together and carefully cut the fiberboard with a hacksaw. After this, you need to reduce the width of the upper and lower frame bars (if you are reducing the width of the door), and remove excess honeycomb (with a wallpaper knife or just with your hands) in order to insert the frame bar. The block can be screwed or fixed with staples. After this, the canvases are glued to the block; for this you can use PVA glue and regular masking tape, if there is no press.
3b. To reduce the width or height of the door leaf by 1-3 cm
Additional wooden blocks and glue will be required to strengthen the door structure. If it was not possible to separate the fiberboard canvas, then you will have to cut along the frame (the tools are the same), then knock out what is left of the block, remove the excess honeycombs in order to insert a new frame block. It is advisable to screw the block. After this, the canvases are glued to a new block; for this you can use PVA glue and regular masking tape if you don’t have a press.
Notes:
- When cutting the door, you only need to wear safety glasses and do not rush, as there is a high probability that the cutting part of the tool will hit the metal brackets holding the frame together.
- If the door is paneled, then it is advisable to cut the width on both sides to maintain the symmetry of the pattern.
4. To reduce the height of the door leaf by 3-5 cm
You will need glue to strengthen the door structure. Cut off the excess part using any of the methods described in point 2. Using a wide chisel, knock off the remaining fiberboard from the wooden block, remove the excess honeycomb (with a wallpaper knife or just with your hands) to insert the frame block. After this, the canvases are glued to the block; for this you can use PVA glue and regular masking tape if you don’t have a press.
After the glue has dried, the ends of the door are planed and sanded if necessary. It is advisable to chamfer the fiberboard canvas in the cutting areas (slightly round the ends). This is best done by hand, using sandpaper attached to an iron or plastic grater.
5. To reduce the height of the door leaf by 5 cm or more
You will need glue to strengthen the door structure. Cut off the excess with a jigsaw or wood saw. This is done quickly, since you mainly have to cut only fiberboard sheets. Using a wide chisel, knock off the remnants of the fiberboard fabric from the wooden block, remove the excess honeycomb (with a wallpaper knife or just with your hands) to insert the frame block. After this, the canvases are glued to the block; for this you can use PVA glue and regular masking tape if you don’t have a press.
After the glue has dried, the ends of the door are planed and sanded if necessary. It is advisable to chamfer the fiberboard canvas in the cutting areas (slightly round the ends). This is best done by hand, using sandpaper attached to an iron or plastic grater.
Note: If the door is paneled, then it is advisable to cut at the top and bottom to maintain the symmetry of the pattern.
In cases 1 and 2, cutting the door takes 1-3 hours. To cut the door in cases 3-5 it will take 2-4 hours, and it is advisable to wait 1 day before completely dry glue, although you can install the door with tape.
Help me fix this bug.
This is the first time I’ve done any repairs on my own, and this is the first time I’ve made such a mistake. It turned out that the new doors, which I bought for a lot of money, in general, do not fit the height of the doorway. I'm a little shocked and didn't even think it would happen like this. How can this be fixed?
doors for bathrooms and toilets: how to trim a door from the bottom
Is it possible to cut MDF doors?
Is it possible to cut the door from the bottom?
If the doors are not “paper”, plywood or Canadian type, then they can be cut a little to size so that they fit into the doorway, or the doorway itself can be enlarged. A the best method there will be a purchase new door, exactly the size of the doorway. If it is non-standard, order doors of the required size from carpentry shop or workshop.
how to reduce the height of a door saw off a door
master class to shorten a door without chipping
Is it possible to saw off a door from the bottom cheaply?
how to cut a door with a jigsaw yourself
Your problem is not as bad as you think
Not only beginners, but sometimes even professionals in their field encounter it. If the door turns out to be larger than the doorway, then you just need to adjust the door to fit right size. To do this, the door just needs to be carefully trimmed. Just do this very carefully and carefully so as not to damage other elements of the door. Reduce the door little by little so that it does not become much smaller than the doorway.
trim interior doors, how to install a toilet door yourself
how to trim a box from the bottom
How to trim a laminated door?
I wonder how you are going to file doors that are covered with PVC film? Or laminated profile? And it’s even better if it’s the entrance steel door... It’s not so easy to deal with metal. You can do it differently. Go to the market where I sell doors and make an exchange deal. True, you will have to spend a little, since the seller needs some kind of benefit from this.
What is the best way to trim a door without damaging it?
It also seems to me that it’s better to just replace the doors if everything is so critical. If you bought a door for a lot of money, it will be a shame to ruin it by trying to fit it to the opening, if at all possible. In some cases, it is probably easier to fit the opening to the door, but the easiest thing is to hand over or exchange these doors.
How to trim doors, tell me how to trim doors evenly?
The bad thing is that the size of the discrepancy was not indicated, but nevertheless they gave sensible advice, I especially liked the idea that you could try to replace the door. It’s as if I hadn’t thought of this myself, I would have immediately started racking my brains about where and what to remove to fit the door, even to the point of widening the opening and installing a new door, if the jamb was decent, but go and try to exchange the door for God would never have thought of anything less... maybe no one would even want to, but it would certainly be worth trying to use such an attempt.
how to trim doors with glass insert
how to prune wooden door video
how to shorten it yourself interior door
I also believe that if you did not order a door to your size, that is, you bought a standard one, albeit an expensive one, then it can be returned to the store within two weeks or exchanged for another, according to the consumer rights law. If the discrepancy is small, then you can still try to fit the box under the door, I still wouldn’t touch the door.
how to trim a door without removing it from its hinges
how to trim a door to height along with the frame
How to trim a door video
It would seem, why cut an already installed and working door. However, sometimes such a need arises, for example, if the installation of interior doors has already been carried out earlier, and during the next renovation the owner needed to lay laminate flooring on the floor, but the height of the doors was not designed for this. In this case, it is much easier to shorten the door than to replace it with a new design. The question is how to do this correctly and competently.
Any homeowner, when producing, expects that the new design will serve him, as they say, faithfully, for many years. To do this, he chooses reliable and quality doors from trusted manufacturers or orders from professionals and wants to be sure that he will not need repairs to interior doors. In most cases, this happens, but there are situations when it is necessary to trim the door in height, for example, if during the next renovation the owner wanted to replace flooring, and he decided that laying laminate or parquet board would be a great option. As you know, laying parquet boards and laminate flooring involves changing the floor level, and, therefore, it is necessary to shorten the door so that it does not touch the flooring when closing and opening. After all, it’s unlikely that anyone would think of buying and reinstallation interior doors, entailing large costs.
And here comes the most difficult moment. Few non-professionals know how to trim a door correctly to avoid possible damage and damaged appearance of the structure. Of course, ideally, you should contact specialists who install and repair interior doors and have professional knowledge and a tool for performing this by no means simple operation. But if this option does not suit the homeowner or is impossible for some reason, he can cut the interior door himself. And for this he will need either manual or manual frezer, available in the arsenal of most home craftsmen, as well as video instructions on exactly how to trim the door so as not to spoil it.
Using manual circular saw By the way, you can shorten an interior door without even removing it from its hinges. To do this, you must first carefully measure required size cut, installing the circular saw blade in such a way that when passing along flat surface floor and file the door, making an even horizontal cut across the entire width of the door. You can visually see exactly how the door is trimmed without removing it in the first video instruction in this section. This operation is usually carried out before the laminate is laid on the floor, since otherwise it is much more difficult to trim the door without removing it from its hinges.
In this video you will see how to trim an interior door without removing it from its hinges
A more complex, time-consuming, but at the same time more convenient way to shorten an interior door is to use a manual router. In the second video you can see the whole process in detail. To do this, the door must be removed from its hinges, secured on a flat surface of a table or workbench using clamps, pressing them on top of the evenly aligned wooden block, which will serve as a guide for the router. It is important to install it so that the cutter removes wood strictly at the distance required. With a router, trimming a door will take more time than with a circular saw, because you will have to make several passes, gradually going deeper into the canvas. However, this method of shortening the door is more reliable, especially if House master is not a specialist and
After installing the new carpeting, parquet or laminate flooring, it may be difficult to open and close the door. This means that the door needs to be cut to length. This often happens when you buy a new one. beautiful door. If the difference in height is not very large, you can solve the problem by removing some material from the bottom of the door using planing or sanding. But if the difference is large, then it becomes necessary to cut off part of the door.
What you need to know before you start
If you have a hollow door, you can't cut too much off the bottom. These doors are simply wooden frame with two fiberboards attached to it, and they cannot be cut more than 1 cm; if you have a solid fiberboard or laminated door, you may be able to remove a little more. There are two types of interior doors: a panel (smooth) door and a door with an overlap. The panel door is completely recessed into the door frame and mounted on hinges. A slab door is partially recessed into the door frame, and its edge is on the outside of the door frame. These types of doors are installed on cylindrical hinges, which allow the door to be lifted by removing it from the door frame.
Measurement
If you want to replace old door, then first of all you need to measure the size of the doorway. To do this, you can easily use a carpenter's ruler, which allows you to accurately measure. First you need to measure the height and then the width at the top and bottom of the frame. If there is a difference in width, take the size of the wider part. Add a 2mm gap at the top between the door and frame. If you are replacing a door, it is best to replace the hinges at the same time.
Trimming to length
To allow the door to open and close freely, leave a gap of 4 to 8 mm at the top and bottom. Mark with a pencil how much material needs to be removed from the bottom of the door. Then use a punch to knock the pins out of the hinges. Or if you don't have a punch, you can use a large nail.
Straight line
Next, use a square to draw a straight line across the entire width of the door at right angles to the vertical edges. Place the door on a sturdy workbench or trestle so that it is firmly supported. Remove the marked part at the bottom of the door with a plane or saw and finish the edge, leveling it with sandpaper. If you are using a planer, hold the tool at an angle to the direction you are planing. Then it will be easier to cut the plane.
Belt sander
When using tape grinding machine, should be considered high frequency rotation, so perform the work carefully. Before you begin, check that the sanding belt is properly aligned - turn the tensioner knob so that the belt runs in a straight line over the support surface. Move the machine evenly over the surface. The machine sands very quickly, and if you are not careful, uneven sanding marks will appear on the wood. When sanding the door, it is best to use a 40-grit coarse sanding belt.
Cutting a thin strip
If you only need to cut a thin strip, it is recommended to press the wood strip against the bottom of the door. This will make cutting much easier. Protect the bottom edge of the door from moisture by covering it with paint or varnish. After this, you can hang the door on its hinges again.
Adjusting the door width
First check to see if the hinged edge of the door is parallel to the frame. If this is not the case, first of all you need to plane it to fit it. To leave the clearance necessary for the door to move freely in the frame, install wooden slats 6 mm thick inside the frame on the hinge side. Place the door on the rail. You can then mark the thickness of the material that needs to be removed from the edge of the door that will fit into the frame by running a pencil along the door frame.
Completing door processing
Place the door on the gantry and cut along the line you marked. If you have a door with a built-in window or several small windows and you need to remove more than 5mm, then you need to cut off half of this thickness on each side, otherwise the door will be asymmetrical. To ensure that the door can close smoothly, you can, if necessary, use a plane to make a downward bevel with a base 1.5 mm wide and inclined towards the inside of the door.
