In this article I will talk about doors that are installed in the bathroom. You will find out whether you need to look for special moisture resistant doors and other features of choosing doors to the bathroom and toilet.
Doors to the bathroom and toilet. Size 600x2000 mm.
Installation of doors to the bathroom and toilet raises many questions among door buyers. People often think that installing bathroom doors requires specially selected door panels made of plastic, MDF, or installation in the door ventilation grille. I will say right away that this is a mistaken opinion.
For more than 10 years we have been selling and installing doors to rooms, kitchens, bathrooms and toilets. During this time, a huge amount of information has been accumulated and I can say with confidence that Installing doors to the bathroom and toilet is no different from installing doors to rooms.
Experience shows that installation regular doors in the bathroom:
- Does not increase the risk of door deformation
- Does not cause peeling of veneer, laminate, or damage to paintwork
- The number of calls for faulty plumbing doors does not exceed calls for doors in rooms and kitchens
Plumbing door sizes
Particular attention should be paid to the size of the openings for installing doors to the bathroom and toilet. There is no single standard here and doors of sizes 600x1900, 550x1900 and 600x2000 are often required. All of them are standard and many manufacturers produce doors with a height of 1900 mm. In new houses, sometimes there are openings for installing bathroom doors under doors measuring 700x2000 and even 800x2000.
You will find current prices for installing doors to the bathroom and toilet in the section
And the toilet requires special care and responsibility. There are two basic rules that should be considered before you start deciding on installing a door in the bathroom. Firstly, there must be a gap below, between the floor and the bathroom door, for sufficient ventilation. Secondly, it is necessary to install a threshold in these rooms that would prevent water from flowing out in the event of a flood.
Bathroom doors must have a gap for ventilation of the room.
Door selection
First you need to decide on the choice of door to the bathroom and toilet. To do this, measure the width and height of the door frame. Height of all interior doors the standard is 2050 mm, and the width is: 600 mm, 700 mm, 800 mm or 900 mm.
The door material plays a big role:
- glass;
- plastic with moisture protective film;
- wood coated with varnish or paint;
- laminated on top with chipboard and MDF.
Glass is resistant to deformation, moisture and high temperature, it is environmentally friendly pure material, which does not allow sound to pass through and retains heat.
Glass is the most suitable material for the bathroom door. This material is resistant to deformation, water and high temperature. In addition, glass is an environmentally friendly material, does not transmit sound and retains heat well in the room.
Glass for doors can be frosted, tinted, embossed, mirrored, decorated with plastic or metal inserts. Glass doors have gained great popularity due not only to their excellent characteristics, but also to their fashionable design.
PVC doors are not exposed chemical exposure, fire, deformation under the influence high temperatures, and are also well resistant to high humidity. Plastic retains heat well and has excellent sound insulation. PVC doors are quite varied in shape and color scheme. Special surface coatings imitate various materials: wood, marble, glass. In terms of its advantages, plastic is slightly inferior to glass, and its low price makes them accessible to a wide range of consumers.
Wooden doors are the most expensive and reliable option. But this classic design absorbs water very easily, which is not suitable for the bathroom.
Chipboard and MDF doors are the most popular option for modern renovation. These designs hold up well high humidity, do not deform and have a low cost. But for the bathroom it is still better to choose plastic or glass doors.
If the door to the bathroom is located close to the doors of the kitchen or another room, then it is better to install sliding doors. This design will be easy to use and interesting.
To install doors, you need tools and materials such as:
- perforator;
- screwdriver;
- hacksaw;
- miter box;
- chisel;
- building level;
- mounting knife;
- feather drill;
- self-tapping screws;
- polyurethane foam;
- colored and transparent silicone;
- wooden and plastic substrates;
- carnations for cash.
Return to contents
Installation
The door installation process consists of the following steps:
- Box assembly.
- Installing a frame in a doorway.
- Fixing the door leaf.
- Foaming the box.
- Insertion of handles and locks.
- Installation of platbands
First, you need to assemble the entire structure on a horizontal surface to avoid further distortions and unevenness.
The assembly process includes the following steps:
- Lay out the door frame components on the floor.
- Make the required dimensions of the box according to the width and height of the opening.
- Make markings for the awnings and secure them. To do this, you need to use a chisel to cut grooves on the frame and door.
- Assemble the box, fastening all parts with self-tapping screws.
- Install the frame in the doorway. Plastic wedges are used to secure the box in the opening.
- Check the evenness of the structure using a vertical plumb line or level and make adjustments.
When the box is correctly assembled and installed, the main task done!
Now you can hang the door on it. Wedges are inserted into the gaps between the door and the frame so that the frame is well wedged from the inside. Now you need to securely fix the box in doorway. To do this, use polyurethane foam, the cylinder of which is equipped with a gun. This solution will allow you to evenly fill all the voids between the surfaces.
Before use, the polyurethane foam must be placed in a warm place for 24 hours, but the mixture should not reach a temperature above 30°C. It is advisable to moisten the mating surfaces with water so that the foam adheres well. Adhesive composition shake thoroughly in a container and apply to the joints. Glue mixture should be blown out thin layer, since it increases in size when it hardens. The treated opening should be left to dry for a day.
The next day, you can safely open the doors and start installing handles and latches. The process should be done like this:
After installing the door, the handle and lock are installed.
- Mark the location of the future mechanism.
- Make a hole by installing a feather drill on the drill the right size: usually 16 or 18.
- To install the lock at the end of the door leaf, use a chisel to make a groove.
- Drill a hole for the handle on the front side.
- Insert the handle mechanism with the latch into the holes formed and secure with self-tapping screws.
The platbands are installed with self-tapping screws around the perimeter of the door frame. All joints are treated with silicone. At the end finished design can be coated with varnish or paint.
Despite the apparent simplicity, installing doors to the bathroom and toilet requires the master to have special skills and understand the principles of operation of the entire structure.
Many apartment owners install bathroom doors with their own hands. This not only allows them to save money, but also gives them the opportunity to do everything in accordance with regulations, ensuring high quality executed works.
Having decided to do everything with his own hands, the master chooses the option:
- buying ready-made door block;
- purchase of materials and subsequent production of the product.
In order to independently process blanks and assemble a structure from parts as a whole, you need not only experience in carpentry, but also a workshop with equipment. Most of the inhabitants apartment buildings Dont Have utility rooms or access to special equipment. Therefore, experts recommend buying ready-made entrance group.
This will make installing a bathroom door a simple and easy task.
Experts point out that the design must meet a number of mandatory requirements:
- be resistant to moisture;
- do not let in odors;
- aesthetically match the design of the room.
When going in search of a replacement for existing doors, apartment owners must decide in advance on the type of opening: swing or sliding.
IN small apartment most a good decision there will be plastic ones sliding structures. And where the area allows you to save on space, you can install traditional swing doors.
Selection and purchase of materials
Today manufacturers offer big choice types and models of interior groups. For their manufacture the following materials are used:
- tree;
- plastic;
- metal;
- glass.
For metal doors use aluminum and alloys based on it. They are lightweight, non-corrosive, and do not require special care. Metal-plastic options with double-glazed windows are popular.
Wood for products of this kind is prepared and treated with special compounds. They prevent moisture from penetrating into the structure of the material and prevent the wood from swelling and deforming.
The plastics chosen are polystyrene, acrylic, and other varieties, including combination combinations.
According to the type of construction, doors can be solid (with a solid leaf) or with window openings. The presence of openings serves additional source light, which makes it possible to save energy by not turning on the lamps every time you visit the bathroom and toilet room.
Understanding what material the structure will be made of, you can more easily calculate how to install the door to the bathroom. Wooden parts require one set of tools, metal ones require another.
Experienced craftsmen It is advised to buy a ready-made structure and fasteners in one place. Thanks to this, all the elements will match, there will be no need to redo anything or adapt existing fasteners.
Dismantling
Before installing bathroom doors begins, you must carefully remove the old structure. Handles and locks are first removed from the sashes so that they do not interfere with work. The process consists of three stages:
- dismantling the canvas;
- removal of platbands;
- dismantling the box.
To perform the first operation, you can use any lever, even the handle of a hammer. Having slipped it under the bottom edge of the door, it is lifted, removing it from its hinges. It is advisable to have an assistant who will hold the canvas.
If the hinges are one-piece, then you need to unscrew the fasteners from the jamb (self-tapping screws, bolts, screws) and remove the sash.
Then the platbands are carefully separated from the frame of the bathroom doors. If they are fastened with self-tapping screws, then the parts are unscrewed with an appropriate screwdriver or screwdriver. The nailed nails are carefully pryed up with a nail puller and removed.
It is important not to damage the walls, since a frame of a different design will be attached to them.
Preparation
After removing the old structure, the replacement of doors in the bathroom and toilet begins. To perform the work efficiently, you need to stock up on all the necessary tools. If the process involves dismantling walls, you need to prepare a mixture to seal holes and cracks.
Replacing a door is a labor-intensive task, so it is recommended to have one or two helpers. The number of participants in the operation depends on the material from which the canvas is made. Light plastic can be handled by two people. And made from solid solid wood It is better to install the structure with three people, protecting each other.
If a power tool is used during work, you need carriers the length of which will ensure comfortable work.
You should also pay attention to the quality of lighting. Often the vestibule where the entrance to the bathroom is located is dark. Therefore, you will need a good directional light source, the position of which can be changed at different stages of work.
Medical supplies in case of injury will also be useful: a bandage, iodine or brilliant green, hydrogen peroxide and a plaster.
Required materials and tools
In order to install a bathroom door yourself, the master will need a set of tools:
- a simple hammer with a rubber head;
- pliers;
- universal screwdriver with a set of feathers;
- screwdriver;
- chisel;
- hacksaw (for wood or metal);
- construction knife.
To measure and level the structure you will need:
- roulette;
- level;
- plumb line;
- simple pencil.
Approximate markup It is better not to use a marker; it is difficult to remove.
To change the doors of the bathroom, the technician also needs foam, ready mortar and silicone seal. Rubber inserts are also useful, with which you can provide waterproofing of the room. To level the structure, plastic or wooden wedges are needed. It is recommended to cook in sufficient quantity fasteners, screws and anchors. It is better to buy them with a reserve.
Preparing the opening of the box and canvas
The installation of toilet and bathroom doors begins with cleaning and leveling the sections of the wall to which the frame is attached. Its dimensions are selected to match the dimensions of the opening, so it is important not to damage anything when dismantling the old structure.
Preparing a doorway involves cleaning the walls of any remaining wallpaper, paint, etc. finishing materials. If installation is carried out after repair, then it is recommended to stick self-adhesive paper tape along the edges of the trim along the opening ( masking tape).
Old fasteners are removed from the walls and holes are sealed with cement. Voids are places where moisture accumulates. To prevent fungus or mold from growing in them, a layer of waterproofing tape is fixed on top of the concrete or brick.
That's it for installation work preparation is complete. You can move on to the next phase to install the door group.
Assembly and installation
To learn how to properly install a bathroom door, you can watch a special training video and instructions with photos. It will help you understand the entire sequence of operations, which will speed up the process and avoid common mistakes.
First you need to check all parts of the box so that they are securely attached to each other. After all, installing bathroom doors begins with installing the frame.
Installation of the box in the opening and fastening of the canvas
If a ready-made door block is ordered, the leaf must be removed from its hinges and separated from the frame. After this, the box is inserted into the opening and its alignment begins. Using a level and a plumb line, compliance is achieved with respect to the coordinate axes of the building. Fixation of a given position is achieved using wedges. Then the parameters are checked again horizontally and vertically. Depending on the thickness of the box profile, spaces and cracks are covered.
After this, the doors to the bath and toilet are installed. Together with an assistant, the canvas is hung on the box. It is checked whether opening and closing occurs normally, whether there are any distortions and whether the locks work. If necessary, let the door stand for a while so that it settles. Afterwards the functionality is checked again.
To avoid distortion, the door hinges should be placed tightly on top of each other. Before fastening them inside, they are lubricated with plastic waterproof lubricants (solid oil, graphite grease), which will ensure long-term operation.
Installation procedure for doors made of wood and glass
The process has a number of features related to the weight of the structure and safety measures. The frame is given some time to stand and the sealant (spray foam) hardens. Only after this is the canvas hung in the toilet and bathroom.
Glass door into the bathroom, despite the fact that it is made of impact-resistant glass, it needs protection. Therefore, it must be kept aside while the box is being assembled. It is advisable to protect the surface from impacts and scratches with cardboard.
It is also necessary to protect the tree, which is problematic to restore.
DIY
Having an idea of the sequence of processes, the master knows almost everything about how to install a bathroom door with his own hands. The main thing is to stock up the right tool And required quantity fasteners.
To firmly secure the frame, first drill holes in it. Having placed it in the opening, they mark out places for holes in the wall. The box is removed and holes are made into which plastic plugs are inserted. Then the operation is repeated, screwing in self-tapping screws or anchors to securely fasten the doors to the bathroom.
After checking the functionality of the structure, we move on to the fittings. You can place the handle on a protruding square, which will protect the technological holes in the material from moisture.
Foaming technology
At the fastening stage, the bathroom block is treated with polyurethane foam. This is necessary to fill all possible voids and reliably isolate the room from moisture.
The polymer mass is applied along the height of the door, starting from the bottom and moving up. It is recommended to fill voids to a third of the volume. The foam will fill the rest itself, gradually expanding. And the master will have to fuss less, cutting off the frozen excess.
Experts note that bathroom doors should be hung only after the foam has completely dried. It lasts up to 10 hours, depending on the composition. The manufacturer reports the curing time on the foam packaging.
Only after this are the platbands attached or decorative panels, completing the installation process of the interior group.
Installing doors to the bathroom and toilet with your own hands does not require additional experience in construction. In order for the installation to be successful and the design to please the owner with its durability, it is necessary to follow the procedure and prepare consumable materials and tools in advance.
Before installing a bathroom door with your own hands, you need to plan the work in stages, prepare tools, choose a door with a frame and buy it.
It is important to remember that the toilet and bathroom are rooms with high levels of humidity. You need to choose the material and opening mechanism taking this feature into account. Ideal options In terms of materials for making canvas, plastic, glass and wood are considered. But wood fibers are destroyed by prolonged exposure to moisture. Because of this, it is necessary to choose a canvas with a protective film (lamination). Veneered models are also suitable.
You can install a bathroom door with your own hands using different opening mechanisms. The most popular options are sliding and swing structures(for shared and separate bathrooms).
Important! Fittings installed on the canvas must have a coating that protects against moisture. Otherwise, the mechanism will rust and fail.
Required Tools
Before you start dismantling the old panel, preparing the doorway and installing a new door frame, you should think about what tools you will need for the work and prepare them. Sample list:
- Hammer, pry bar, sledgehammer, pliers, hacksaw for wood and metal.
- Building level, plumb line, pencil, 3 meter tape measure.
- Screwdriver, hammer drill, large grinder (when expanding the opening).
TO consumables This includes plastic, wooden and metal substrates, fasteners (anchor bolts, self-tapping screws, polyurethane foam, nails for trim) and accessories for power tools (diamond blades for an angle grinder, drills, drills, bits).
Dismantling the old canvas
Before installing a new canvas with a box, you need to remove the old structure. This requires proper dismantling so as not to damage doorway. You need to prepare a chisel, axe, hammer, pliers, pry bar, wood saw (you can use a hand-held circular saw or chainsaw).
Procedure:
- The old structure needs to be removed. To do this, you need to open the door. Insert a pry bar under its base to create a lever. Press down on the other end of the tool. If the blade does not lift, the hinges need to be lubricated with motor oil or WD-40. If the opening mechanism is secured with bolts or screws, it is enough to unscrew them to remove the blade.
- It is necessary to dismantle the platbands, extensions and frame. Platbands and extensions are removed using an ax, chisel, pliers, and hammer. It is enough to pick up one edge of the wooden plank and tear it off the box. Wooden trims It is better to replace rather than reuse.
- You need to start disassembling the box by removing the fasteners, if any (bolts, screws). The box is cut with a wood hacksaw, chainsaw or hand circular saw in the middle along the right or left slope. Using a pry bar, the box is carefully torn away from the wall along the perimeter.
Plastic trims are fixed to the wall using silicone or sealant. They need to be cut off with a sharp knife, and the remaining adhesive should be removed from the wall with sandpaper or a blade.
Preparing the doorway
Before starting the main installation work, you need to prepare the doorway. To do this, working surfaces are checked with a level and tape measure. If there are differences in size, depressions or bumps, they need to be leveled. At the stage of preparing the doorway, you can change its width.
Important! When expanding the opening, you need to use a large grinder. Builders recommend not using impact power tools (jackhammer, hammer drill). It creates a powerful vibration that can destroy a wall.
After determining the dimensions of the opening and leveling the working surfaces, it is necessary to apply waterproofing. It will protect the box from the destructive effects of moisture and prevent fungus from developing. For this, waterproofing tape is used, which has a self-adhesive side. It needs to be glued around the perimeter of the opening.
Door frame installation
When the waterproofing is applied, the surfaces are leveled, the opening is prepared, you can begin installing the box. The sequence of actions will depend on the material. When installing a plastic box, it is enough to level the finished structure and place plastic spacers. It is necessary to fix it with anchor bolts to the walls and foam the empty space between the wall and the box. It is important not to forget about the direction of opening the canvas, so as not to do unnecessary work.
The wooden box is measured initially. After this, its height and width are reduced so that a technological gap remains between the box and the wall. Also, we must not forget about the hole for ventilation, which should be located between the door leaf and the threshold. A lath is placed along the contour of the opening or a profile is secured. This is the base on which you need to attach the box. To do this, use anchor bolts and foam.
Installation of door leaf
The fabric separating the toilet or bathroom from other rooms is installed in different ways. Installation features depend on the type of opening mechanism.
Swing models are equipped with hinges that are secured to the canvas and frame with self-tapping screws.
The situation is identical with plastic models. The door is put on hinges. Metal elements are closed with plastic caps (in PVC models).
Installation of platbands
Platbands are decorative wooden, metal or plastic strips that should cover the junction of the wall and the frame. You can secure them to the box using finishing nails. At the stage exterior finishing, you need to carefully nail the platbands to the box so that bare wall and the foamed areas were closed.
Door foaming technology: step-by-step instructions
To improve thermal insulation and better fixation in the passage, it is necessary to foam the empty space between the box and the entrance. The composition is applied as follows:
- Before applying foam, it is necessary to moisten work surface. In this way, better bonding of the two materials can be achieved.
- Before opening the container and applying foam, you need to shake the container.
- After filling free spaces need to wait for it to dry polyurethane foam. Wait 3-4 hours.
Advice! Builders recommend leaving the foam to dry for 24 hours before further work.
Features of using bathroom doors
During installation and subsequent operation of the door block, you need to know the features that will help increase the durability of the structure and help avoid various problems:
- A hole for ventilation is required (between the floor and the canvas). Size - 10 cm wide and 5 mm high.
- The bathroom should have good air circulation. It will help avoid the formation of fungus and mold, preserve appearance decorative coatings and will increase the durability of building materials.
- If the bathroom or toilet is small, you need to give preference to lamination. Coating from natural wood will not withstand prolonged exposure to moisture and will quickly collapse.
- Builders recommend installing sliding doors if the bathroom or toilet is located next to the kitchen or in narrow corridor. This way you can save space.
- To increase the service life of the structure, it is necessary to purchase high-quality fittings. Complex mechanisms (folding and sliding) need to be lubricated with engine oil once a month. Rusted areas are treated with WD-40.
Additionally, around the perimeter of the door you can install rubber compressor. It will improve sound insulation. It is necessary to leave a ventilation hole under the door leaf.
You can install doors to a bathroom or toilet without the help of finishers. It is important to follow the sequence of actions, carefully select the design of the opening mechanism, the materials from which the blade is made, and the tools.
Having chosen the doors to the bathroom, we need to install them. It is advisable to do this yourself, because installing a door in the bathroom is another opportunity to save money and gain practical experience.
Installing a bathroom door differs from installing standard interior doors. The main differences here are considered to be a larger gap between the floor and the door to accommodate good ventilation, as well as the height of the threshold under the door, but this moment always remains at the discretion of the bathroom owner.
The Right Size of Bathroom Door
Most often, the door size is standard, or differs from the standard by stably, say, 10 cm. This mainly concerns the width of the doors, since the height most often remains the same.
Before purchasing a door and frame, you will need to check these dimensions, because it is better to spend a couple of minutes taking measurements and writing in a notebook than to purchase doors of the wrong size. It’s good if a specialized market is nearby and the doors can be exchanged, but it may also be that you will install the bathroom doors in the country, which means you will have to adjust the doorway or the size of the door leaf, which is difficult and not very fast.
In general, the main point here can definitely be considered correct measurements, which are strictly your responsibility.
Tools and materials for installing bathroom doors
It’s good when your home chest is filled with everything you need, but it also happens that something may be missing and work will stop. To prevent this from happening, check availability in advance. necessary tools and materials for the installation of bathroom doors, and if anything is missing, immediately buy more, for example, at the same time as the door.
Tools for installing a bathroom door
We will need an almost standard set: drill, hacksaw, chisel, level, plumb line, screwdriver, tape measure, pencil, construction knife.
Materials for installing a bathroom door
Everything is also simple with the materials: the doors and frames themselves, self-tapping screws and anchor bolts, polyurethane foam, wooden wedges.
During the work process, you may need some other items, which we will definitely remind you of.
Assembling the door frame and door together
If you purchased the doors and frame separately, it is advisable to immediately assemble the structure to make the work easier. But remember, it would be better to buy initially assembled version, if it fits in size, of course.
- We lay out all the components of the box, as well as the doors themselves, on the floor.
- We collect door frame around the door, pre-drill holes for fasteners, trim, measure and prepare the box for installation.
- After the elementary process, we proceed directly to installing the box in the doorway.
Installing interior doors in the bathroom: step-by-step instructions
When the box is assembled and you have prepared everything necessary for further work, we move on to the most important process, which we are talking about today. We'll give you the opportunity to learn how to install bathroom doors step-by-step so that the job doesn't seem too complicated. So let's begin:
- Installing a bathroom or toilet door begins with installing the frame in the doorway, before which it must be tried on;
- After fitting, the box is placed in the doorway and wedged with wooden or special plastic wedges. At the same moment, you can make all the necessary edits;
- Now you should check the verticals and horizontals of the box with a level and plumb line;
- After checking the levels, the box is secured with anchor bolts or dowels, which should be inserted flush into the material. If everything is done correctly, then the wedged box is marked in places where it is secured with anchors or dowels and drilled, also, holes in the doorway are marked through the holes in the box, and the box is removed. Now, holes are made in the walls with a drill, after which dowels are inserted into them. The frame is installed in place and finally secured, the hinges are cut in and the doors are hung (we will talk about this process in more detail below);
- Next, we will need to foam the box to seal the seams;
- The foam is prepared for the process according to the instructions - it is screwed onto the gun, shaken, and so on, after which it is poured into the seam evenly, but without overdoing it, since polyurethane foam tends to increase in volume by 3-5 times or more (it would be more correct to use professional polyurethane foam , which does not gain excess volume);
- The seams are foamed by about a third, from bottom to top, after which you need to wait about a day for the foam to dry.
After foaming, the polyurethane foam must dry for 24 hours, and only after that it will be possible to begin subsequent work.
Inserting hinges and hanging doors
- The hinges cut into the frame and doors in pairs, but if the doors are heavy, you can use three hinges;
- To insert hinges, you need to make the markings correctly - attach the hinges to the end of the door leaf and simply circle them with a pencil;
- Next, we need to cut into door leaf a small depression, similar to the thickness of the hinge material. This can be done using a chisel, initially beating off the clear contours of the recess to prevent chipping, and then removing the necessary remnants of the material;
- Next, the loops are secured with self-tapping screws, the amount that matches the number of holes in the loop. The top hinge of the bathroom door is fixed at a distance of 15-20 cm from the top level of the door, bottom loop– at a distance of 20-25 cm from the bottom;
- After securing the hinges, it is necessary to install the lock in the door, strictly according to the level and all dimensions, so that after installing the door in the opening, we do not get bevels;
- Now the doors are installed in the opening and wedged with a distance of 4 mm at the bottom and 2 mm at the top; the openings are also adjusted in width. Everything is checked with a level and the location of the hinges is marked on the box;
- We remove the doors from the frame and repeat the process with indentations that can be made with a chisel;
- We cut in the hinges and finally install the doors (the process may be slightly different if you chose a different type of hinges, for example, hinges that are simultaneously attached to the door and frame, and so on).
Be careful and be sure to consider the most convenient hinges for installing bathroom doors, as there are several types of them - classic, hinges without mortise, screw-in hinges, double-sided loops, card one-piece loops.
Only after this process, having installed the door and wedged it correctly, clamping all the screws and once again checking the operation of the door, you can perform the foaming that we talked about earlier.
Decorative finishing
By this stage we mean cutting off the excess polyurethane foam after it has dried and finishing the door and frame with special trims that will hide all the not-so-nice moments. Installation of platbands is carried out using self-tapping screws or decorative fasteners. Then all that remains is final finishing doors if you choose painting or varnishing.
Installing a bathroom door (video)
Installing a bathroom door, for which we have provided step-by-step instructions and a training video, is considered a job that is difficult to complete the first time. Therefore, if you are confident in your abilities, have everything you need at hand and are ready to try, you can proceed, but if you have purchased an expensive door and are worried about the quality of installation, it is better to turn to professionals.
