Any product has its own service life. And a metal door is no exception. Even with high quality steel door after ten years of operation, problems may arise, not to mention low-quality Chinese products, which until recently were in high demand among the mass consumer, attracting with their spectacular appearance and low price, but not verified time.

The reasons why the front door needs to be replaced may be different, but all of them can be combined into several groups.

If you haven't made your choice yet, take a look at our offers

1. The temporary “tin” door installed by builders in new buildings has served its intended purpose.
2. The door does not meet modern safety requirements and does not provide adequate sound insulation and heat protection.
3. The door, initially classified as “cheap,” failed early due to poor-quality material and installation, distortions and deformations, damage to components and fittings, and wear of the finishing layer.
4. When identifying manufacturing defects and defects resulting from improper installation of the door, which cannot be corrected on site. In this case, it is necessary to check the quality of the installation and admit the error of the product manufacturer or installation specialists. Replacement is carried out at the expense of the manufacturer (installer).
5. Damage lock system. If repairing or changing the lock does not restore the performance of the metal door without forced opening, then it will most likely need to be replaced. You need to call a technician, and if he determines that the owner is at fault for improper operation of the mechanism, then the door will be replaced at the owner’s expense (full cost). If the current warranty period has not expired, you need to request that part of the costs be covered by the company with which the service agreement was concluded.

The complexity of replacing a metal door and the time costs are commensurate with the initial installation. In addition, you need to be prepared that you may encounter some difficulties in the work process. So, the doorway, which during the time long-term operation old door may have been damaged and found to be "weak" for a new, possibly heavier structure, and may require strengthening. And in some cases - expansion or contraction.

Ready standard door does not always fit in size to the opening in which its predecessor was fixed. If the purchase turns out to be smaller in size, then, of course, they can install it, but the voids between the opening and the box will have to be filled with a fair amount polyurethane foam. But is it even worth purchasing a narrow door to the apartment, because bringing in and out of large objects will be very problematic.

There is only one way out of this situation - individual order and mandatory “branded” installation. Initiative self-installation in this case may be punishable. Only a professional, based on his own experience, will be able to take into account all the nuances that will ensure in the future the trouble-free operation of all systems and comfortable operation of the front door. But the owner needs to be present when replacing the door and monitor the work of the master. Firstly, help may be required, and secondly, under the “watchful eye” of the owner, as a rule, the quality of workmanship increases noticeably.

A responsible master will not estimate everything by eye, but will resort to construction level, which will help align the new door with the walls and ceiling. It’s no secret that in old houses it’s not easy to place a door perfectly vertically, there are distortions doorways meet all the time. Therefore, creating a tightness that prevents the absence of cracks and drafts is a task of paramount importance. A good, securely installed seal solves the problem. The quality of welding must also be of high quality so that the entire structure is strong and can withstand vandalism.

Like these important details In addition to checking the operation of the locks, the owner of the apartment should pay attention when accepting work. This kind of “technical control” will only be for the good and will ensure the “longevity” of the service of the metal door.

When choosing a door for an apartment, many people look not only beautiful model With good insulation, but they also want the design to be reliable. The canvas and box, welded from thick steel using solid sheet bending technology, using hinges on bearings and anti-removal pins, are able to resist vandalism and serve for a long time in daily use. But it is important to correctly replace the entrance metal door in the apartment, using GOST-approved fastening units and the technology for their creation, since defects in the actions of the installers can negate high performance products and open access to intruders.

Taking dimensions and preparing the opening to replace the door in the apartment

First, it is important to correctly take measurements from the opening when determining the dimensions of future doors. If there is a threshold, then all this will be removed during the dismantling of the old structure, so you need to apply the tape measure to the floor itself. At the top above the opening there is a floor slab, which is usually not cut out for expansion, which is why you cannot buy a larger structure. It is necessary to take care of the margin for adjusting the position so that the box does not adjoin closely to the top plate. A gap of 20-50 mm is sufficient.

For width, measurements are taken not at the box itself, but at the corners of the opening, where the layer of plaster is thinner. Here, too, a gap of 20-30 mm is provided on each side, so that when replacing the entrance door in an apartment, it can be tilted for alignment (in the case of a curved edge of the opening or uneven floors). The width of the installation gaps can be greater (up to 100 mm in total), which is covered with foam on the room side and platband on the outside, so you can deviate smaller from the existing dimensions if you cannot find a door of the required dimensions.

When a new product is selected and delivered to the site, preparation of the opening begins. To do this, dismantle the old door. If it was made of metal, then the canvas is removed from the hinges and the anchors are unscrewed. In most cases, instead of them there are pieces of reinforcement hammered into the wall and welded to the box. The rods are cut behind the box, inserting a grinder disc between the wall and the vertical post. After removing the frame, the protruding pieces are hammered or loosened and removed. All plaster nearby is chipped off, and debris and dust are cleaned up.

Stages of replacing the front door in an apartment

When the opening is ready, you can begin installation. The cost of replacing the front door in an apartment by a team of professionals is only a few thousand rubles, but if there is necessary tool and skills in handling it, then you can try to do the work yourself and save a little. Otherwise, it is better not to take on such a responsible task and trust experienced professionals.

Work on replacing the front door, regardless of who carries it out (professionals or the owner), must be carried out according to the following scheme:

1. The new canvas is removed from the hinges so as not to damage it. The box is wrapped with film or masking tape to prevent scratches on it from the tool.
2. The box is installed in the opening on wooden wedges, which are laid on the sides and bottom. If the apartment will have floors (parquet or laminate), then a beam is placed under the threshold so that it is higher than the future floor line.
3. It is important to make sure that the box is even, for which a bubble level is applied on both sides to the vertical post. An error of no more than 3 mm is allowed.
4. Using a hammer drill, a hole is made through the mounting eye and an anchor is hammered into it. The head of the fastening element should not protrude outward in such a way that it interferes with the closing of the sash.
5. On next stage drill holes on the opposite side of the box and fix it in a similar way. A total of 6 fixation points are made.
6. The canvas is hung on the hinges, having previously lubricated them, and tested for correct operation.
7. If everything is in order, then the installation gap is foamed and left to dry, after which the excess parts are cut off with a knife.

Cost of replacing the front door in an apartment

If the right tools and there are no skills, it is better to entrust the installation to professionals. The work will take no more than two hours, and the result will allow the door to be used for a long time without distortions or friction. In this case, in addition to the product, you will have to pay only a few thousand rubles more, but this is subject to dismantling the old door yourself. If you transfer this function to the craftsmen, the price will increase by another 700-1000 rubles, depending on the complexity of the design.

When sizes new door do not correspond to the opening, then its expansion or narrowing is required. In the first case, a part of the wall is cut out with a grinder and a concrete disc, and the internal pieces of the slab or masonry are removed with a hammer drill. In the second situation, when the opening narrows, it is blocked wooden beam or foam block, which depends on the thickness load-bearing structure. Payment for such work is carried out separately.

The cost of installing a new door to an apartment is determined based on the following factors:

• product weight (up to 80, 100, 200 kg);
• type of construction (number of sashes);
• recycling old doors.

After installation, the gap is sealed, which costs from 350 rubles. If necessary replace front door to a turnkey apartment, then the implementation of slopes is added here, for which they use additional panels made of MDF and laminate. This frees the owners from additional work and gives the wall near the box a finished look that matches the interior in the hallway.

The Panther company offers big choice doors to the apartment that have reliable design and tight insulation. We carry out installation with delivery and possible additional work on the opening, as well as turnkey replacement, with the manufacture of accessories.

If you want to replace between room doors was done cheaply, use the services of private specialists registered on Yuda. Qualified installers interior doors They will dismantle old units and install new units efficiently and in a short time.

Professional installation of door blocks

If you decide to install new doors between rooms in a Brezhnevka, Khrushchevka or other type of house, to carry out installation work It is better to call an experienced specialist. Qualified craftsmen will perform all types of work quite cheaply, including removing old doors and adjusting the doorway to the parameters of the new one. door frame.

Professional specialists will install interior doors in the following sequence:

• will dismantle the old canvas, remove trim and boxes
• clear the doorway of residues finishing materials, increasing it if necessary
• will carry out installation and carefully secure the structure
• will install fittings and decorative elements

Finishing dismantling works Yudu performers will collect the waste left after the renovation and take it to a special place for disposal. After replacing the frame and door leaf experienced specialists seal the gaps and check the doors for smooth operation (opening and closing).

The cost of installing a door frame, door leaf and trim

Prices for installing room doors in Moscow are quite varied. Much cheaper to replace door design call a private master rather than use the help of specialists from large companies.

Using the YouDo service, order a service such as replacing interior doors in an apartment - the price will depend on a number of factors:

• type of housing ( a private house, Khrushchev, Brezhnev, new building)
• the room in which the doors are installed (kitchen, bedroom, bathroom, living room)
• cost of fittings
• urgency of repair, need to increase or decrease the doorway

Approximate prices for door installation are indicated in the price lists of specialists registered on Yuda. Experienced craftsmen They carry out work on installing new doors in Moscow with high quality and at affordable prices.

Why is it profitable to order the services of a private master?

Calling a specialist to install doors in the kitchen or other room with the help of Yudu is very profitable. Qualified craftsmen know all the installation features, so they carry out work on installing new doors professionally and quickly.

By ordering door installation services from experienced Yudu contractors, you will receive a number of significant advantages:

• Before proceeding with the installation of the door, the specialist will calculate the cost of the work
• The master will install the door in compliance with the standards and requirements
• After completion of the work, the contractor will provide a guarantee for the installation performed.

The website youdo.com has a rating system, so you can quickly find a specialist for high-quality door installation. Replacement of interior doors will be carried out professionally by qualified craftsmen, because they use reliable fittings and special tools for their work.

Sections of the article:

IN modern houses and apartments, interior doors are the most important and integral element of the interior. No matter how high-quality its design is, over time the doors will still need to be replaced due to improper use, and due to natural wear and tear.

In order to replace doors, you don’t need to gather your strength and wait for inspiration for production overhaul. Replacing doors in an apartment will require investing significantly less material costs and effort than complete renovation throughout the entire home.

What should you consider?

Changing doors with your own hands is not that difficult, but during the process you need to take into account many different factors.

First of all, you need to decide what kind of door structure will be installed to replace the dismantled one. Nowadays, there is a huge choice - from cheap and affordable plastic models to high-quality and expensive doors made of natural wood.

The most important step when replacing interior doors is the accurate execution of all necessary measurements. The following parameters need to be defined:

• Width of the door block;
• Distance from the extreme point of the top of the jamb to the threshold;
• The thickness of the door leaf.

At self-replacement doors it is recommended to purchase ready product together with the box, thanks to which you can significantly speed up and simplify the installation process. It is equally important to decide in advance which direction the door will open, since this determines which side to hang the hinges on.

When installing expensive solid doors made of natural wood, it is better to turn to professional installers.

Door dismantling

Replacing doors involves dismantling the old structure. First, you should get rid of the platbands using a hammer and chisel, and then carefully remove the door leaf.

To lift and remove the door from its hinges, you will need a nail puller placed from below. By carefully pressing on the other end of the tool, you should move the blade up.

Then, using a saw, the vertical posts of the box are divided into two parts and, using the same nail puller, it is removed from the doorway.

You must remove the box carefully and carefully, trying not to damage the wall.

Box assembly features

Before installing the frame during the process of replacing interior doors, it must be assembled.

First of all, the width and height of the opening freed up after dismantling are measured. old box. Based on the obtained dimensions, two vertical posts are cut out and top bar. The box should only be assembled in a horizontal position.

The crossbars are cut at an angle of 45º on both sides, and the racks are cut only at the top. Then these elements are used to create a structure in the shape of the letter “P”, in which all angles are equal to 90º.

After which, at the points of intersection of the crossbar with vertical posts holes are drilled, the diameter of which is 1 mm less than the diameter of the screws.

Replacing interior doors involves using high-quality self-tapping screws to assemble the frame, the length of which exceeds the thickness of the stand by 5 mm.

To control compliance with the required gap between the posts, the door leaf should be applied to them, while there should be a gap between the posts for the lock. It is recommended to place a rectangle of cardboard measuring 200x20x3 mm between the frame and the door for a while.

When installing the box in the opening, you must use a plumb line to ensure that the racks are in a strictly perpendicular position to the floor. Three holes are drilled in both racks and in the wall, after which the box is secured with self-tapping screws.

Hanging the door leaf

Before hanging the canvas, you need to attach the hinges to the posts. A chisel is used to cut the hinges, and self-tapping screws are used to secure them. This work is done on the floor in a horizontal position.

You should retreat 200 mm from the bottom and top, attach the loops and circle them with a marker or pencil. Then use a chisel to make indentations. A job such as replacing interior doors requires deciding in advance on the type of hinges, which can be right- or left-handed.

Before choosing hinges, you need to know in which direction the canvas will open. You can choose universal hinges that allow you to open the door in both directions. It should also be taken into account that the higher the weight of the door, the longer the hinges should be.

After securing the hinges in the required places, you can hang the door leaf.

All gaps left between the frame and the wall when replacing doors are filled with polyurethane foam. First, you should moisten the wall with water to improve the adhesion of the plaster to the foam, and in order to keep the box clean, it is recommended to seal it with masking tape or plastic film.

All other gaps are then filled with foam. The door will be completely ready for use within a day.

Installing a lock and handle

The most important step in changing doors is installing the lock and handles. Door knob consists of a push or turn type mechanism, a counter plate, a halyard tongue and a locking mechanism.

To install the handle, you need to use a drill or a screwdriver with an appropriate attachment to drill a hole in the door leaf. A recess is machined at the end of the canvas rectangular shape, into which the mechanism is inserted and fixed using a plate or self-tapping screws. Then the handle is inserted, and the axle is trimmed if necessary.

Finally, a counter plate is attached into which the halyard tongue fits. The counter plate, like the plate on the canvas, must be installed flush. It is convenient to use a chisel or a “feather” to make recesses.

Replacing interior doors in an apartment ends with a final check of the correct operation of all structural elements.

Final stage

Replacing interior doors at the final stage involves bringing the entire structure into a “marketable” form, for which excess polyurethane foam is carefully trimmed with a sharp knife or blade.

Then the platbands are installed, which should be measured in advance and cut at an angle of 45º relative to each other. To install them, it is necessary to retreat 10-15 mm from the side where the hinges are attached, and on the other side, a gap of 6-10 mm is sufficient.

If the walls are smooth, then MDF trim can be attached using liquid nails. To secure wooden platbands It is recommended to use small nails covered with finishing nails on top. The nails are driven into the platband to a depth of 10-15 mm, and the heads are masked with a wax pencil matched to the color of the platband.

The door replacement is complete, all that remains is to periodically lubricate the hinges and take care of the result of your labor.

Every person understands that the main criterion that any entrance door must meet is reliability. Of course, when planning to purchase such a product, at first glance it is quite difficult to determine how durable and reliable it is, so it is important to approach this process responsibly. If a person wants to replace the doors to an apartment, then of course, initially he will study it appearance, since the door can be considered the face of any home. But do not forget that the main function of the door leaf is to protect the room, so you still need to take care of the reliability of the structure.

To replace the entrance door to your apartment and remain satisfied with the process, you need to choose the right product. When choosing a door leaf, you initially need to familiarize yourself with the design features, type of locking system, insulation features and more. Since not every person knows what design a door should have, it is necessary to first familiarize yourself with this information.

Correctly select and replace the front door

Every person must understand that apartment door replacement is a responsible process. External features It’s not difficult to evaluate products, the main thing here is to choose suitable option facing material. But for the main ones design features It is worth paying much more attention, especially to the following points:

• the thickness of the metal used in the manufacture of the structure must be at least 1.5 millimeters. It is better to choose products made from a single sheet of metal;
• the profile used in the manufacture of the door leaf frame must be solid, since welding elements make the structure more vulnerable and not so strong;
• the presence of horizontal and vertical stiffeners improves the performance properties of the structure;
• the presence of insulation in the middle of the door, which increases sound and thermal insulation properties designs.

The exterior decoration can be anything, but if a person wants to inexpensively replace the entrance door to an apartment, then it is better to choose budget options, for example, with powder painting, vinyl leather or plastic. In addition to all of the above, when choosing a door leaf, you should also take into account the number of locks; it is recommended that there be at least two. The hinges also have great importance, their number must correspond to the design features. When choosing a door leaf, you need to make sure that there are anti-cuts, anti-removal pins, armor plates and more.

How to replace the entrance door to a turnkey apartment

The choice of the door leaf itself is initial stage In addition to replacing the product, other related processes must be carefully considered. Our company makes it possible to replace the entrance door to an apartment on a turnkey basis, that is, we provide a full range of services related to such a process. We employ experienced and qualified specialists who professional level are engaged in the installation of door structures, and are also able to correctly measure the doorway.

We carry out the manufacturing process ourselves door leaves Accordingly, our specialists know exactly how to install the product. Our specialists install the structure taking into account existing standards. We understand that the quality of installation significantly affects the durability of the door structure, therefore we take this process with full responsibility.