Acrylic bathtubs have won the love of housewives all over the world with their smooth surface, glossy shine and impeccable whiteness. Lighter plastic models of various shapes and sizes have successfully replaced clumsy cast iron washing containers.

Happy owners of acrylic plumbing fixtures often wonder how to clean the font in order to maintain its original condition. appearance products for a long time. In fact, you should be careful in this matter, since not every cleaning product is suitable for mechanically fragile plastic. In this article we will tell you how to care for an acrylic bathtub so as not to spoil it.

Advantages of acrylic

Many homeowners are concerned about how to clean acrylic bath, since they have heard a lot about capriciousness plumbing equipment from this material. In fact, acrylic products are much easier to care for than steel or cast iron wash containers.

The ease of cleaning is explained by the following properties of the polymer:

• Low porosity. There are practically no pores on the acrylic surface, so it does not absorb dirt, but repels it, so daily cleaning of an acrylic bathtub can be done simply with warm water and a soft cloth.
• High smoothness. The smooth surface of acrylic does not allow dirt and harmful microorganisms to become embedded in the structure of the material, so it is easy to clean the bowl even without the use of abrasive detergents.

Note! Manufacturers often talk about the “self-cleaning effect” that they have quality products made of acrylic. This term means that their nasty surface repels dirt, so you have to clean the bathtub less often. In most cases, you can wash an acrylic bathtub with warm water or soapy water.

Typical contaminants

Since polymer plumbing fixtures have replaced cast iron and steel fixtures relatively recently, the question of how to clean an acrylic bathtub at home is relevant for many responsible housewives. Acrylic products repel dirt, however, intensive use of the device leaves its mark, deteriorating the appearance and hygiene of the washing container. Most often, the following contaminants occur during the use of a bath:

Important! Properly caring for your plumbing fixtures so that old stains do not appear on them is much easier than washing an acrylic bathtub. Therefore, it is important to rinse regularly inner surface bowls with warm running water and then wipe dry with a soft cloth after each use.

Many housewives do not know how to clean an acrylic bathtub, so they use completely inappropriate products that corrode, scratch or otherwise damage the product. Improper care is the most common reason premature wear of acrylic sanitary ware. Manufacturers recommend not using powders to clean such bathtubs; instead, it is better to use a delicate, gentle washing gel or cream. To care for acrylic plumbing, 4 categories of cleaning products are used:

Please note that if you are not sure what product to use to wash your acrylic bathtub, it is better not to take unnecessary risks. It’s better to try what effect the composition will have on small area surface, and only then continue cleaning the product.

"Forbidden" techniques

High quality acrylic plumbing fixtures are a godsend for modern housewives who save time on everything they can. At correct operation it retains whiteness and shine even without the use of special products. However, washing an acrylic bathtub with the wrong household chemicals can ruin the product. Manufacturers recommend not to use for care:

Prevention

An important measure to combat contamination on the surface of acrylic bathtubs is proper care in compliance with the manufacturers' recommendations. Using the product correctly is much easier than washing an acrylic bathtub at home. Compliance with these 4 simple rules significantly extends the service life of plumbing fixtures:

Remember that by using a low-quality or unsuitable product to clean an acrylic bathtub, you are not getting rid of dirt, but of expensive plumbing fixtures!

Video instruction

Acrylic bathtubs are more common on sale today than products made of cast iron or steel. Light weight and relatively low cost make them popular among buyers. But at the same time, acrylic is a rather capricious material that requires careful and careful care.

Standard contaminants

Modern acrylic has dirt-repellent properties. But during active use by household members, sooner or later, the bathroom becomes “overgrown” with stains, its appearance and hygiene deteriorate significantly. Therefore, many housewives are thinking about the question of how to clean an acrylic bathtub at home?

The most common contaminations for such products are the following:

• yellowness. In principle, it is not scary for acrylic and is not its enemy, as, for example, for a bathtub made of cast iron or steel. However, acrylic is not immune from its appearance. The most common cause of yellowness is poor quality water from the tap;
• limescale and deposits. Salts various metals contained in tap water, over time settle on the surface of the bathroom, forming limescale;
• other spots that may appear during the operation of the product. This is contamination from hair dye or other dyes. Protective upper layer and the smooth surface of acrylic practically does not deeply absorb such contaminants. Therefore, it is possible to wash an acrylic bathtub from such troubles with any special means.

Prohibited tricks

Before you start cleaning such products, it is important to understand what should not be used in such work. The following tools and available materials are considered undesirable:

• Abrasive detergents are powders containing crystals. They can scratch the sensitive surface, which will not only ruin the appearance of the product, but will become a breeding ground for bacteria that can easily penetrate microcracks. In addition, the shine will leave the surface of the acrylic, it will become dull and unsightly. Abrasives include not only purchased products, but also improvised ones. For example, baking soda or citric acid undiluted in water, tooth powder, etc.;
• chlorine or products containing it. Under its influence, the acrylic surface may darken and swell, and pores will appear on it due to the destruction of the polymer structure. The same applies to substances such as ammonia, acetone and various formaldehydes;
• hard brushes, sponges, washcloths. An ideal alternative to such items is a soft cloth;
• very hot water. It is no less dangerous for the acrylic surface than acetone or solvent. Under influence high temperature The surface of the bath may become deformed.

Methods for certain types of pollution

Before using any removal product various kinds contamination (purchased or popular), it is necessary to test it in an area hidden from prying eyes. This way it will be possible to preserve the appearance of the product, in case the cleaning composition is too aggressive.

How to clean an acrylic bathtub if it is not possible to purchase commercial cleaners? The most common and universal remedy– regular menthol toothpaste. The composition is applied to dirty areas using a soft toothbrush and gently rubbed into the surface. After that, wash it off clean water.

Rust

Rust stains from the surface of acrylic can be removed in several traditional ways. For example:

• soap solution and baking soda. Dissolve one teaspoon of liquid soap or two teaspoons of shavings in 0.5 cups of water. laundry soap. Add 3 tablespoons of baking soda to the resulting mixture and mix well. Treat dirty areas with a cloth soaked in the product and leave for 30-40 minutes. Rinse with warm clean water;
• A paste of water and baking soda will quickly clean fresh rust spots on an acrylic bathtub. Mix soda with water and wait until the grains swell, becoming a little softer. Apply the mixture to a sponge and gently rub the dirty areas. Rinse with water;
• Finely ground table salt will remove old rust stains. Sprinkle salt on the stain and gently rub it with a sponge dipped in turpentine. Then wash with warm water and liquid soap.

Important! Any abrasive should be applied to the acrylic surface with extreme caution. Otherwise, you will have to solve another problem: how to remove scratches from the surface of the bathtub.

Yellowness

You can remove yellow stains from an acrylic bath using products sold in stores. household chemicals. They are designed specifically for acrylic coatings. For example, “Akrilan” or “Tim-Profi”. These compounds may lead to original appearance even too neglected plumbing products. Among other things, such products will disinfect the surface. However, you should not abuse them. Too much high efficiency is associated with the high content of various chemical compounds and substances in these products that harm not only the acrylic surface, but also the health of family members. Therefore, it is enough to use them for general cleaning of the bathtub (1-2 times a month).

An acrylic bathtub can be removed from yellowness using folk ways and available components that are used by many housewives. These include:

1. Table salt and wine vinegar. You need to proceed as follows:

• In a glass container, mix wine vinegar and salt in a ratio of 2:1;
• heat the resulting solution in the microwave to a temperature of 70 degrees;
• soak in liquid soft cloth and wipe dirty places;
• leave for 30 minutes.

Important! Do not overexpose the solution, otherwise it will damage the surface.

2. Citric acid. Dissolve 20 grams of lemon in one glass of water. Spread the resulting composition evenly over the surface of the product with a cloth and leave for 30-40 minutes. After this, rinse with warm water. After this procedure, the bath will acquire its original snow-white color.

Limescale

Limescale deposits on an acrylic bathtub can be removed with citric acid or vinegar. The bathtub needs to be filled to the top with warm water (35-40 degrees). Pour in 0.5 liters of table vinegar or add 50 grams of lemon. Leave for 12 hours, then drain the water and rinse the bath with clean water. It is better not to use these two remedies at the same time. Vinegar can react with baking soda and corrode the surface.

How to properly care for an acrylic bathtub?

Acrylic can withstand shock loads. However, it will not be difficult to scratch it if handled carelessly. Small cracks are favorite places for dust, bacteria, dirt, as well as metal impurities contained in tap water. Therefore, you should avoid the appearance of such scratches and do not place metal buckets, basins, or pans in an acrylic bathtub. Also, you should not bathe your pets in such a bath. They can scratch the surface with their claws.

The more often acrylic is cleaned, the better for the material itself. Regular care and quick removal stains will simplify further cleaning of the product and there will be no question of how to wash off stubborn dirt.

After each bathing or other use, the bathtub must be thoroughly rinsed with clean water and a mild detergent. This can be liquid soap or dishwashing gel. After such a procedure excess moisture must be wiped with a dry cloth or towel. General cleaning of acrylic surface sanitary product should be carried out at least once a month. To do this, you can use substances that are more aggressive than liquid soap and dish soap. Cleaning gel is applied to inner covering bath, leave for a few minutes, then rinse with water.

To prevent troubles such as lime deposits and yellowing, it is necessary to regularly check the functionality of the taps. Constantly dripping water leaves rusty yellow marks on the surface of the bathroom.

If stubborn stains or microcracks suddenly form on the bathtub, they can be cleaned with sandpaper, then rubbed with liquid acrylic and polished. But without skills, this procedure will not be successful. Therefore, it is better to entrust such a task to specialists.

Acrylic is difficult to clean at first glance. By following the above recommendations, you will be able to keep your bath snow-white and clean for a long time.

Almost all of us love it when you walk into the bathroom and it shines with snow-white cleanliness and a smooth, delicate surface. But, unfortunately, this does not always happen. Over time, they appear on the bathroom yellow spots, and often the bathtub turns yellow. You may ask, what to do if the acrylic bathtub turns yellow?

Causes of spots

In order to answer your question, let's look at the reasons why an acrylic bathtub turns yellow:

• An acrylic bathtub turns yellow due to poor quality manufacturing. In this case, it is best to restore the bath yourself, or contact a specialist.
• The bathtub has turned yellow due to improper care or lack thereof. In this case, you can try to clean it with detergents.

In order to better understand how to clean an acrylic bathtub, consider the properties of the material with which it is covered.

Information: Acrylic is a hard plastic and therefore does not corrode. But it also has disadvantages. The biggest disadvantage is that acrylic is susceptible to mechanical stress and is easy to scratch. For such baths, you cannot use detergents containing chlorine, ammonia, or acid.

Acrylic is also afraid of boiling water, acetone, and gasoline. We also very often see yellow spots on an acrylic bathtub, which is a consequence of a leaking faucet.

Choosing a cleaning product

To clean an acrylic bathtub, we will have to purchase a cloth or soft sponge (we said above that acrylic is easily scratched), as well as detergents. Let's look at some of them:

• Sif - this product is suitable for almost the entire bathroom, and does not contain abrasives. It cleans the bathtub perfectly, you can clean the taps and tiles. To clean the bathtub, you need to spray it for a few minutes and then rinse off.
• Acrilan is a foam intended for cleaning showers and bathtubs. It perfectly cleanses soap stains, as well as rust, plaque, various fungi, and old stains. This product also prevents the appearance of limescale, thanks to the film that forms after washing.

Important! Acrylan should only be used with rubber gloves and stored out of the reach of children.

• Bass is a product for everyday use. The product is used in liquid form.
• Tim-pro is a product whose direct purpose is to clean acrylic surfaces. It cleans heavily soiled areas well, while being environmentally friendly, and also removes bad smell. At the same time, it creates a coating that has dirt-repellent properties.
• Cinderella is a relatively inexpensive, at the same time quite effective, cleaner for acrylic bathtubs. But it also has a pungent odor. Considering that the product is an aerosol, it is appropriate to use it in hand and respiratory protection equipment. Then wait 7 minutes after spraying and the bath will need to be rinsed cold water from the tap and allow the bathroom to ventilate.
• Cleaner - this product has a special formula that allows you to effectively clean acrylic bathtubs, tiles, faucets from limescale, soap stains, grease, and corrosive deposits. This product has acrylic polymer, which repels dirt, as well as an antibacterial and antifungal composition.

There are many different detergents such as Luxus professional, Cillit, Acryl - Net, RAVA K, “Panny Bath” and many others.

...and no “chemistry”

In addition to industrial detergents, folk ones can also save your bath:

• If you have yellow stains on your bathtub, they can be removed with regular toothpaste;
• Another way. Mix baking soda with soap and apply it to dirty areas. After about 20 minutes, rinse with tap water. This usually helps;
• To remove rust stains and limescale deposits, it is good to use a mixture of ammonia and hydrogen peroxide. The proportion is one to one. To remove dirt, soak the hard part of the sponge in the solution and wipe the dirty areas.

Bath resuscitation

Now let's move on to the most unpleasant event, when the acrylic bathtub has become very yellow and the “rusty” spots are thoroughly ingrained. All available methods Tried cleaning, but no results. The bathtub has fallen into disrepair. And even if at first glance everything is lost, you shouldn’t throw it away. Today's technologies make it possible to revive acrylic coatings. This can be done by contacting specialists. But if you wish, you can return your favorite bathtub to a new life at home yourself.

Let's start with the most simple ways and situations:

• There are scratches, scuffs, and rust spots on your bathtub. To do this, you need to purchase acrylic polish and follow the instructions to remove the damage.
• If you have cracks or chips, they can also be restored at home. To do this, you need to purchase an acrylic restorer repair kit. Then carefully drill out the edges of the crack or chip. After this, rinse well and dry the area being repaired. Degrease it, and after reading the instructions, dilute the acrylic reducing agent. Apply to the surface following the instructions. After drying, grind the surface and polish it to a shine.
• In case of through-and-through damage, a reinforcing repair kit can be used. To restore, you will need to seal the hole outside the bathroom with glass mat. After drying, with inside, apply acrylic reducer.

Conclusion

And finally, if your bathroom is so terrible that spot repairs are useless, there is also a way out. To restore, we wash the bathtub, then use sandpaper to rub away scale, limescale, and rust. After that, soak it in water. Then wash thoroughly with soda and mustard powder. Then rinse and dry.

When our bathtub is well washed and degreased, we putty it with automotive putty. After letting the putty dry, we rub it with sandpaper so that the putty is equal to the acrylic. We blow out all the dust, then wipe the bathroom clean and fill it with acrylic. After drying, you get a new, perfectly white and smooth bathtub. At the same time, you will save your budget. In addition, you will be sure that in six months your bath will not lose color.

Cleaning an acrylic bathtub is quite a serious undertaking. It must be approached responsibly. It is important to know that not every remedy is equally suitable for this.

Acrylic bathtubs always look beautiful and that is why they are so popular. They are light in weight, and there are also many on sale. different forms and sizes, so they fit any bath. This is an excellent alternative to replace cast iron containers.

Those who use acrylic bathtubs often do not know how to properly care for them. In reality, this issue requires a careful approach, because not every means can be used to clean such plumbing fixtures, otherwise it can simply be ruined.

What is good about acrylic: advantages

Often owners of acrylic bathtubs are interested in how to clean them properly, because such plumbing fixtures are capricious and do not tolerate careless handling. In fact, caring for acrylic is very easy, unlike other materials.

The ease of cleaning can be explained by several properties of the polymer:

• Small porosity. Acrylic has extremely small pores, if any, and therefore dirt is not absorbed, but remains on the surface. So, you can simply clean your plumbing fixtures every day with a cloth and soap and it will never lose its appearance.
• Smoothness. Due to the fact that acrylic is smooth, pests cannot penetrate the material. So no abrasives are required to clean the surface.
• By the way, Manufacturers often talk about the self-cleaning effect. This does not mean that the surface cleans itself. Simply due to the smoothness, dirt is repelled. So you have to clean it less often. Most often, cleaning can be done with plain water and soap.

What are the types of stains on acrylic bathtubs?

Since polymers have become very popular not so long ago, it has become very topical issue regarding cleaning acrylic bathtubs at home. Acrylic products are excellent at repelling dirt, but with intensive use they leave a mark that makes the appearance worse and also makes cleaning more difficult. As a rule, you can find the following types of pollution:

• Yellowness. Over time, acrylic does not turn yellow, but this does not mean that this does not happen. To eliminate such contamination, you need to rinse the bowl using special products and install water filters, because the problem is precisely that the water is very dirty.
• Limescale. This defect can be observed when water with a high content of metal salts is used. Citric acid is ideal for eliminating it.
• Colored spots. Multi-colored stains can appear on the bathroom due to different dyes. The surface of the bathroom is quite smooth and this prevents the pigment from being too absorbed, and therefore any product will cope with such stains.

To prevent large contamination from appearing on your plumbing fixtures, make it a rule to care for them regularly. So try to always wipe the bathtub dry after washing.

What products should not be used to clean an acrylic bathtub?

Please note that an acrylic bathtub cannot be cleaned using any means. If you don’t want it to lose its appearance, then remember that you absolutely cannot use:

• Bleaching. Do not try to clean the surface with a product containing chlorine. Instead of a beautiful surface, you will end up with a dull color that will ruin your plumbing. If you carry out the treatment again, small pores will begin to form, where dirt will always get in.
• Washing powder and abrasives. The abrasive scratches the surface and is destructive for acrylic. After treatment, scratches and damage may appear, which, of course, can be hidden by polishing and grouting, but the curved appearance of the bathtub makes this process difficult.
• Ammonia. If you use ammonia solutions, the acrylic surface will gradually deteriorate and lose its glossy shine.
• Acetone, gasoline and thinner. All these products are strictly prohibited for acrylic surfaces. It becomes cloudy and loses its attractiveness. If you use solvent regularly, you risk damaging the surface.
• Formaldehyde. Today, as a rule, formaldehyde is not used in household chores, but it is still important to know that they are not compatible with acrylic.

How to properly care for an acrylic bathtub: rules

• If you do not wash the bath on time, this will inevitably lead to the formation of severe dirt. To avoid this, try to wipe the bathtub with a sponge and soap after each wash.
• By the way, if you rinse the bath hot water, then it will shine even more. Most importantly, forget about hard brushes and sponges, otherwise you will damage the bathtub.
• Before applying any of the products, try spreading a little of it in an inconspicuous place and wait a little. If no changes are visible, then you can safely begin cleaning. Pay close attention to the disinfection process, because without it, harmful microbes begin to form in the pipes.
• Do not forget that chlorinated solutions are prohibited for use. Chlorine may also be present in special products, but only additional elements carefully reduce its impact.
• If you want your bathroom enamel to shine, rub the acrylic in a circular motion with a soft cloth. Pre-moisten it with a polish with a wax base.

How often should you clean an acrylic bathtub?

It is recommended to wipe down the acrylic bathtub after each use. We recommend following this rule, because it is easier to remove small dirt than stubborn dirt. This can be done with soap and a soft sponge, and after rinsing, wipe dry with a cloth.

As for the use of active substances, use them once every couple of weeks. Apply the product over the entire surface, leave for a short time, and then rinse well.

To prevent the formation of yellow discoloration, monitor the condition of your plumbing fixtures. If faucets start to leak, repair them as quickly as possible. If it turns out that the bathtub has turned yellow, then you can remove it with special means.

What products can be used to clean an acrylic bathtub?

Acrylic is one of the subtypes of plastic and has excellent performance characteristics. Like steel baths, the material cannot rust or peel off, and even the dirtiest water is not afraid of it.

However, household chemicals are not acceptable for polymers, and third-party products should never be used. How then to remove pollution? Here you need to choose substances that will not react with acrylic. These include citric acid and vinegar.

But first you need to make a solution out of them, and not use them as is.

• Vinegar solution. To make something simple, but good solution, fill the bathtub two-thirds with water and pour 9% vinegar. For cleansing you will need 0.5 liters. Mix everything well and leave it for 12 hours.
• Lemon acid. The same cooking algorithm is used, but just keep in mind that the granules may not dissolve and settle on the bottom. They will not give any reaction and will lie there. To avoid this, dilute the powder first and only then add it.

Today you can find good products on store shelves. They are effective in combating rust or limescale. Let's talk about them.

Soap and dishwashing detergent are considered the most gentle of all. You can clean the bathroom with shampoo or shower gel. If you run out of one of the products, then just rinse the bottle and wash the walls of the bathroom with it. Such products will not harm the top layer and act gently.

If your bath has lost color and turned yellow, then you won’t be able to get by with simple soap. To do this you need to use polishing agents.

You should not use powders such as Pemolux, Biolan or Comet. First of all, they contain abrasives, and they also need to be rubbed in. So it's better to use liquid means or pastes. They will not damage the surface. You just need to work with them with gloves, since the composition is often aggressive.

If you decide to use such products, then the best among them are Bass, Cif and Acrilan. The latter is specifically designed for acrylic bathtubs.

Is it possible to clean an acrylic bathtub with Domestos?

Yes, undoubtedly, it is quite possible to use Domestos, but it has its own nuances and a competent approach to this matter will provide excellent results. The product contains hydrochloric acid, and it copes very well with limescale and rust.

It will easily remove all dirt from the bathroom without harming the surface. This is a modern cleaning product that has become popular due to its effectiveness. Specifically, it has the following advantages:

• High reliability and safety
• Low cost
• Removing plaque and dirt
• Gentle treatment of the surface

Is it possible to clean an acrylic bathtub with Sanox?

This product is more affordable than Domestos and has similar properties. However, it also whitens surfaces well, which makes its use more widespread. The rules of use are almost the same as for Domestos.

After application, it must be left for some time for the effect to be effective. Today Sanox comes in several types:

• Spray

Gel and foam should be applied to the entire surface, and the spray should be sprayed. It is advisable that the spraying be carried out 10 cm from the surface.

How to remove defects from an acrylic bathtub?

Acrylic coating is not only susceptible to dirt. Sometimes scratches and other defects may appear on it. In a way, acrylic is unique because it scratches easily, but at the same time, it is also easy to remove the damage.

To remove small damage up to 0.5 mm, use felt. It is great for polishing surfaces. If the scratches are deep, then they can only be removed with a special product - liquid acrylic.

You don't even have to contact a specialist. You can buy a repair kit, which includes a spatula and a tube of product. It is applied to the defect site and rubbed in with a spatula. When the product hardens, you can treat it with felt.

Liquid acrylic allows you to eliminate even a large hole made through. Cover the outside with tape and put acrylic into the cavity.

Some defects and stains are very strong, and therefore the use of any means will not help. In this case, only special inserts will help out. Also, do not forget that acrylic does not like very high temperatures. Boiling water won't harm him, but the ash from a cigarette can leave an imprint.

How to prevent dirt and damage on an acrylic bathtub: preventive measures

Most effective method To prevent serious contamination, follow the manufacturer's recommendations. It’s better to use it wisely so you don’t have to worry about cleaning it later. There are only 4 simple rules that you need to follow and your plumbing fixtures will last a long time:

• Wipe the bathtub dry each time after use.
• Try not to type too much hot water
• Rinse the bathtub with a sponge and soap after use
• Do not use disinfectants frequently. It is enough to do this a couple of times a week

Always remember that improper cleaning of the bathroom can ruin expensive plumbing fixtures. So think before you use any products.

Video: How to wash and clean an acrylic bathtub?

In addition to dirt and soap scum, plaque often forms on the bathroom. Its intensity and color depends on the quality tap water. White limescale is caused by an increased concentration of hardness salts, rust is caused by excess iron, and yellowness is caused by the content of chlorine in tap water. The problem of plaque can be solved by proper and regular care with traditional methods or special household chemicals.

Traditional methods of removing dirt and plaque are popular everywhere - many home remedies can actually cope with the problem quickly and without additional financial costs. But it is worth noting that it is easy to remove limescale and yellow deposits using home methods. Rust is much more difficult to remove, and if it is old, you cannot do without household chemicals.

Homemade recipes for limescale

Liquid soap

A common option for everyday product care. Using a soft sponge, treat the bath with the product and rinse with water. This is enough to remove daily dirt and keep the surface clean. You can also wash your acrylic bathtub with washing gel or dish soap.

Vinegar

Table vinegar dissolves lime deposits well. Used alone or in combination with citric acid, salt or soda. The main thing is that in the case of acrylic, do not use it in pure form. 0.5 - 1 liter of 9% vinegar is diluted in a bath filled with warm water. Leave for several hours (but no more than 12), after which the solution is drained, and the bath is wiped with a sponge, rinsed with water and wiped dry.

Lemon acid

Powder citric acid used in a similar way to vinegar, but it must first be dissolved in warm water. For light whitening you will need 50 g of powder (this is 2 packs of 25 g each), for plaque removal - 100 - 200 g.

It is necessary to dissolve all the crystals so that they do not settle on the bottom of the bathtub. Freshly squeezed lemon juice applied to a sponge can be used to wipe off small yellowed areas.

Soda

Washing an acrylic bathtub with soda often causes controversy among professionals and on thematic forums. Baking soda effectively whitens and removes limescale, but as an abrasive substance it is of concern. In order not to harm the acrylic surface, you should soften the abrasive effect of soda: to do this, dissolve it in a bath of warm water and leave for 30 - 60 minutes. Then the solution is drained and the bath is rinsed with water. Another option: dilute baking soda with water to a paste-like consistency, apply for 15-20 minutes and rinse.

Folk remedies for yellowness

Laundry soap

A universal cleaner for all surfaces. Using laundry soap, you can prepare a cleaning gel that effectively removes stubborn dirt and whitens yellowed areas. To do this, grate the soap and dilute it with warm water to a thick, uniform consistency. Add 1 - 2 tbsp. l. soda and mix well until it dissolves, apply with a sponge. The exposure time of the product is from 15 to 60 minutes.

Soda and mustard

Combine soda and mustard powder in equal parts, add warm water and stir until the soda dissolves. The resulting slurry is used to treat rusty and yellow areas and leave for 30 to 60 minutes.

Vinegar and hydrogen peroxide

Vinegar and peroxide are mixed in a 3:1 ratio and applied with a sponge or spray bottle. After 15 minutes, wipe the treated area with a napkin and rinse with water.

Toothpaste

Whitening toothpaste can be used to clean an acrylic bathtub from yellow plaque and fresh traces of dyes (for example, such stains may remain after hair dyeing). Rub the paste into problem areas with your fingers or a sponge, leave to act for several minutes and rinse with water.

Recipes for rust

Salt and lemon juice(vinegar)

Finely ground salt is mixed with the juice of half a lemon or 2 tbsp. l. vinegar until you get a paste. The composition is applied to rusty spots and left for a period of 15 to 60 minutes. You cannot rub the surface with this composition - it is washed off, and the remaining rusty deposits are removed with a sponge.

Hydrogen peroxide and ammonia

Solution from equal parts peroxide and ammonia can remove limescale and fresh rust. The action time should not exceed 10 minutes: ammonia in ammonia can harm the acrylic surface.

Special means

Industrial products for acrylic are presented in the form of liquid sprays, creams or gels.

Compositions suitable for acrylic can be found among consumer household chemical products and from manufacturers of branded sanitary ware. Professional products can not only remove stains and old plaque, but also return the bathroom to its original color.

Industrial products active against plaque and dirt of various origins:

Note: It is advisable to test any new product on a small area before use.

How not to handle acrylic

Acrylic - durable polymer material and a bathtub made from it will last a long time if mechanical and chemical damage to the surface is avoided, namely:

1. Do not use aggressive cleaning agents based on chlorine, concentrated acids and strong alkalis (Domestos, Belizna, Pemolux). Due to chlorine, the bathtub may turn yellow, and caustic substances can destroy the acrylic layer and cause cracks.
2. Do not use hard brushes or metal scrapers for cleaning - they easily scratch acrylic. Polymers are characterized by a non-porous surface, so when proper care There is nowhere for dirt to accumulate and there is no need for rough cleaning. But when defects appear, dirt easily gets into the damaged areas.

How to remove scratches

If scratches do appear on the bathroom, they can and should be eliminated to avoid further damage to the material. Cracks, chips and defects that form when the surface is corroded by aggressive substances also require restoration.

Acrylic bathtubs are easy to restore, so minor defects can be removed at home. Scratches can be removed fairly quickly:

• the damaged areas are carefully sanded with sandpaper of different grain sizes (from coarse to fine);
• A special polishing compound is applied to the cleaned area and treated with a fleece or special cloth in accordance with the instructions.
  

  Note: Small scratches can be removed with a special polishing pencil for acrylic surfaces.

Serious defects can be eliminated using putty, liquid acrylic and polish. Often such work is entrusted to professionals, but if you wish, you can do it yourself in several stages:

• Use masking tape to separate defects from undamaged areas;
• cracks and chips are sealed with starting putty;
• after the putty layer has dried, the damaged areas are rubbed first with coarse-grained sandpaper, then with fine-grained sandpaper;
• if small unevenness remains, add a layer of finishing putty and, after it has dried, sand the surface again with fine-grained sandpaper;
• remove the masking tape and degrease the surface with alcohol;
• after completely dry After all layers of putty, a special paint is applied to the treated areas (its color is selected in accordance with the shade of the bath);
• Finally, polish is applied to the dried layer of paint.

For convenience, you can purchase a repair kit for acrylic bathtubs. The standard kit includes polish, a set of sandpaper of different grits and polishing cloth.

Step by step how to remove scratches is described in the video below:

Cleaning your hot tub

If hydromassage equipment is installed in the bathroom, weekly cleaning of the nozzles and regular disinfection of the system will be required. If it gets into the hoses lather, the remaining dirt and organic compounds begin to decompose and cause an unpleasant odor. When water circulates in the system, this dirt ends up in a common tank, which makes the bathing procedure unhygienic.

To fix the problem yourself, you can purchase special disinfectants for hot tubs. The bath is filled with warm water, an antiseptic is added and the hydromassage is started for 10 - 15 minutes. Then the water is drained and the bath is thoroughly washed to remove any remaining disinfectant.

Antibacterial solution Ravak Disinfectant for plumbing and hydromassage systems.

Note: Chrome whirlpool jets can only be cleaned with products designed for chrome surfaces. This should be taken into account when choosing a bath detergent. Otherwise, the chrome elements may darken or become stained.

At least once a year, it is advisable to contact specialists who will professionally disinfect and clean the hydromassage unit - including the filter and water supply system.

Bathroom care

Caring for an acrylic bathtub comes down to preventing persistent contamination and, as in the case of cleaning, not damaging the surface layer. To do this, it is important to observe the following preventive measures:

• Monitor the serviceability of taps, shower hoses and mixers: leaking plumbing is the main cause of rusty streams.
• Pay attention to the composition of cleaning products for faucets and shower heads that are mounted above the bathtub container or fixed above its surface. Drops of detergent will certainly fall on the surface of the bathtub and leave stains on it or cause damage to the acrylic layer if the active substance is aggressive.
• Do not exceed the exposure time of cleaning agents: after a long time, even acrylic-safe compositions can form undesirable reactions. Their most harmless consequences can be stains and discolored areas on the surface of the bathroom.
• Do not wash or soak laundry in acrylic bathtubs, especially in bleach solutions. Colored clothes may stain the container when washed.
• Avoid hitting the surface of the bathtub or dropping heavy objects on it.
• Do not place basins or other containers with hard bottoms or sharp edges in the bathtub.
• Do not burn the acrylic surface with curling irons or curling irons.
• Be careful when bathing animals: their claws can scratch the acrylic layer. Therefore, it is better to organize another place for this procedure or lay a rubber mat on the bottom of the bathroom.
• Do not pour hot water into the bath bowl, especially boiling water - it destroys acrylic, and the thin coating of a low-quality product can even melt. Safe water temperature for cast acrylic bathtubs is up to 80°C, for sandwich structures – from 50 to 70°C (depending on the thickness of the acrylic layer).
• To restore antibacterial properties acrylic coating periodically disinfect the bathtub with special solutions.

Ideally, it is recommended to wash your acrylic bathtub daily with liquid soap and be sure to wipe the surface dry after each use. But with the modern rhythm of life, it is quite difficult to implement this in practice. Therefore, it is advisable to wipe the bathtub at least once at night and clean it with a suitable product once or twice a week. Additional use of polishes will reduce the frequency of washing the acrylic bath and prolong the effect of the shiny surface.

Advice! If you need bathroom renovation specialists, there is a very convenient service for selecting specialists from. Just fill out the order details, the experts will respond and you can choose who to collaborate with. Each specialist in the system has a rating, reviews and examples of work, which will help with the choice. Looks like a mini tender. Placing an application is FREE and does not oblige you to anything. Works in almost all cities of Russia.

If you are a master, then go to, register in the system and you will be able to accept orders.