Perhaps the most annoying and troublesome breakdown that can occur in your home is a sewerage malfunction. Repair sewer pipes may be needed for many reasons and at any time (even the most inopportune for you). After all modern sewerage- this is serious technical complex, serving the entire house and combining the bath, toilet, all sinks and others washing machines, including dishwasher and washing machine. Moreover, internally, all these elements are connected into one network, with many connections and interconnections, which, of course, is not immune to breakdowns.

Thus, if there is a sewerage problem, the entire house may be deprived of its usual amenities for several days. Of course, it is best to entrust the solution to this problem to a special technician who will quickly and efficiently fix the problem.

What can you say about a sewer malfunction:

1. Pipes or plumbing may leak
2. The plumbing becomes clogged, or the water begins to flow poorly
3. Crack in the pipe
4. Unpleasant smell

In any of the above cases, immediately after detecting damage (or signs thereof), you need to block or secure the breakdown and call a technician. Further repair of the sewer pipeline will depend on the extent and location of the breakdown.

Sewer blockage

The simplest type of sewer problem is a clog. It can be determined by the slow flow of water into the sewer or the absence of drainage at all. But you shouldn’t rush to get rid of the blockage yourself, because without the proper experience and equipment, such methods may not be as safe as they seem. With inept repairs, you can not only achieve no results, but even completely damage the pipe and the system as a whole.

Therefore, even if there is a blockage, specialized workers will be better able to determine its cause and eliminate the problem itself. For this purpose, tools of varying degrees of complexity can be used (depending on the degree of contamination):

— plunger

- liquid chemicals

— cable for cleaning sewers, etc.

Leak repair

Experienced craftsmen They immediately determine the location of the sewer pipe leak and find a solution to the problem. Most often, a leak occurs at the entrance to the pipe: it is either an inaccurate connection between the siphon and the drain hole, or the siphon and the pipe.

A master can carry out such repairs of sewer pipes without even dismantling the plumbing and the entrance to your sewer system. To fix the problem, an experienced worker just needs to tighten the connections, replace the gasket or seal the entrance to the pipe. This damage can be dealt with in the shortest possible time and without major repair work.

More attention from the technician will be required if the leak occurred due to a poor-quality connection of the sewer pipes themselves, because repairing cast-iron sewer pipes will take a little longer and will require workers to intervene in the system itself.

In this case, the master will first determine what was used to strengthen the pipe connection earlier. His further actions. If there is lead caulking, then the joint will need to be cleaned and a new, more durable connection and seal will be required.

And if the connection was cement, first the master will remove old mortar, will check, clean and strengthen the joint, and then fill it with cement again. Experienced craftsmen can carry out such repairs on a cast iron sewer pipe in one visit, without causing much harm to your interior.

Getting rid of cracks in a pipe

Another option for sewerage breakdown is a crack in the pipe itself. In this case, the employee must assess the extent of the damage and the size of the work to be done. If only a small crack appears in the pipe, a specialist will quickly solve this problem with the help of a dull chisel.

However, repairing a sewer pipe can become more complicated if the repairman discovers a medium-sized hole in the pipe. In this case, workers will clean and free the damaged part for work and deal with it by repairing it with a special “plug”, which will be additionally filled with cement for strength and reliability. After this, the master will take care of the tightness of the repaired pipe in order to avoid further unpleasant odor, and will return your bathroom to its previous working appearance.

Replacement of sewer pipes

However, it is worth remembering that even the most experienced worker will not be able to repair a cast iron sewer pipe in the following cases:

— the pipe already has a lot of damage (past and present)

- the pipe has rotted from time to time

- if there is a defect in the product or its installation

In this case, you cannot do without replacing the pipe or sewer system generally. Of course, this is the most difficult and time-consuming method of repair, but by using the services of experienced workers, you can save time and your nerves.

Repair of plastic pipes

One of the most simple types work in case of a sewerage breakdown is the repair of plastic sewer pipes. Experienced craftsmen are well aware that repairing such pipes, in principle, makes no sense due to the imminent secondary breakdown. With each intervention, the strength of the product itself is significantly reduced. In this case, replacing the old pipe with a new one will be much cheaper than its further maintenance.

Of course, in the case of small cracks, the technician, at your request, can cover them with sealant, but you need to understand that this is only a temporary measure, and further replacement cannot be avoided.

External sewerage repair

It often happens that a sewer problem is not limited to your home, but affects the entire system. In such cases, in order to identify the cause and location of the breakdown, repairs must be carried out along the entire length of the sewer pipe leading from your home.

At first glance, this may seem too complicated and time-consuming, however, if you entrust the work to the craftsmen, it is possible to repair sewer pipes without opening them, which will take the employees no more than one working day.

Good afternoon, dear readers!

Has it ever happened to you that the sewer in your house is clogged, and it is impossible to reach the repairman? If not, then rest assured: there is still more to come. The drainage system will not always work like a clock, so it is important for every owner to know the intricacies of its maintenance.

Sewerage is a system of pipelines connected to plumbing and household appliances. The purpose of this design is outflow Wastewater from the premises. If the system is mishandled or worn out, malfunctions occur and repairs are required.

Common problems and reasons for their occurrence

Most often, residents are faced with the problem of clogged drains. There are 2 reasons why this happens:

1. When installing the pipeline, the builders violated the technology, which led to the formation of stagnant areas. In a private house, due to improper design of the system, the system freezes and an ice plug interferes with the outflow of water.
2. During operation, the sewage system was used incorrectly and preventative cleaning was not carried out. Animal fat, hair, and food waste enter the system and form impenetrable plugs at the turning points of the pipes.

Another problem is the natural wear and tear of the pipeline. Constant loads lead to leaks, cracks, and the formation of fistulas, and this cannot be done without repairs.

What is required for repair

Set of tools and Supplies depends on the type of problem and the material from which the sewer pipeline is made. I recommend having everything you need because you never know what kind of emergency will happen.

Tools:

• hammer;
• chisel;
• Bulgarian;
• Screwdriver Set;
• pipe cutter;
• drill;
• cable with a brush.

Consumables:

• clamps;
• couplings;
• sealant;
• cement;
• rubber compressor;
• chemical solvents.

If you need to replace part of the pipeline or riser during repairs, you will additionally need a pipe made of cast iron or PVC.

Basic methods of do-it-yourself sewer repair

Common problems with the water drainage system in an apartment are blockages and leaks. Depending on the material from which the sewer system is made, a method for troubleshooting is selected.

Blockage

There are 4 ways to deal with blockages. I had the opportunity to use all 4 in practice, each copes with the task in its own way. The main thing is to correctly correlate the cleaning method and the scale of the blockage.

If your toilet or sink is draining slowly, it is wise to use the following methods. Perhaps repairs can be avoided:

1. Everyone has a rubber plunger in their apartment. If used correctly, it will clear the clog quickly. Press the rubber tip firmly against the drain hole. There should be water in the sink or toilet at this moment. Perform 15–20 sharp pressures from bottom to top, making sure that the tip is firmly held on the earthenware. Then forcefully remove the plunger. The waste will rise to the surface.
2. Cool boiling water will help remove fat deposits. Pour boiling water into the drain, wait 20 minutes and drain the water.

If the water does not go away, but rises up with the waste, use one of the following options:

1. An effective method is chemicals to remove blockages. I used the drug "Mole", and I am pleased with the result. Other advertised products, such as "Mr. Muscle" or "Tiret", are also effective. You can pour a mixture of salt and soda into the hole, pour a glass of 70% vinegar essence, then rinse with water 2-3 times. This method will help with minor blockages. Caustic soda removes deposits on pipe walls, but this substance cannot be used for a cast iron system.
2. Purchase a cable with an end from a home hardware store. The principle of operation is to twist the cable in the sewer pipe. At the same time, the brush at the end cleans the walls of plaque. While scrolling, you need to drain the water from the tank several times.

The cause of a clog in the sink is the accumulation of debris in the siphon. This can’t even be called a repair: you need to unscrew the lower part of the siphon and drain pipe, remove waste, rinse and put everything back together.

Leak

An unpleasant smell in an apartment is the first sign of a sewer leak. First you need to understand which area is leaking and promptly begin repairs. The main places are connections and joints. Leakage in these areas occurs from improper use, due to installation errors and as a result of expiration of service life.

When the old one leaks cast iron pipe, change the entire sewer system or just the damaged area. If such repairs are beyond your means, there are other ways to fix the leak:

• process joints;
• repair a fistula or crack;
• remove the blockage.

If the leak has formed in a place hidden by the floor slab, you will not be able to repair such a defect yourself.

Leaking pipes at joints

Before starting repairs, you need to warn your neighbors and ask them not to use the sewer temporarily. Clean the leak area and dry with a hairdryer. Coat cement mortar with the addition of PVA construction glue. The coating dries within 24 hours. During this time, secure the leak site with a repair coupling.

Crack in cast iron and plastic pipe

For pipes made of cast iron and steel, the following methods for eliminating leaks are suitable:

1. Treatment epoxy resin or construction water-repellent adhesive.
2. Winding rubber gasket with fastening with clamps.
3. A bandage made of absorbent material and further impregnated with epoxy resin.

For PVC pipes use:

• cold welding;
• self-adhesive tape;
• rubber or silicone sealant.

Replacing old fittings with new ones will help completely eliminate the leak.

Clogged sewer system

If sewerage is installed incorrectly in private homes, water supply pipes freeze. If a blockage has formed at this time, then under the influence of cold the blockage expands and puts pressure on the walls of the pipeline. As a result, cracks appear on the surface. The same situation is typical for apartments in Khrushchev-era buildings. For small defects, it is enough to coat the cracks with sealant.

Repairing cracks in sewer pipes

Daily sewer riser experiences stress and pressure. The comfort of residents on all floors depends on the serviceability of this pipe in the apartment. If the riser was installed many years ago, repairs in case of severe deformation will help little; it is better to replace the damaged area completely.

For temporary fixation it will help:

• wrapping with plumbing flax;
• coating with a mixture of orthophosphoric acid and copper oxide in a ratio of 2:3;
• sealing with a solution of powdered ammonia, iron filings and sulfur.

In plumbing stores big choice rubberized clamps with metal frame And different diameters. Installing this will permanently eliminate a crack in a riser made of steel, cast iron or PVC.

How to replace a sewer pipe in an apartment

When completely worn out, the damaged area must be replaced. The services of a road repair specialist, but you can install a new section yourself. If the damaged area is under a tile or decorative panel, then you can’t do without an autopsy. Consider this as an additional cost when repairing the pipeline.

Stages of dismantling an old pipe

Before starting repairs, it is necessary to dismantle old pipe, turn off the water and disconnect the plumbing fixtures from the sewer. Then do the following:

1. Break if necessary cement screed and release the pipe.
2. Disconnect fittings.
3. Using a grinder or pipe cutter, cut off the pipe, moving 5–10 cm away from the installation site.
4. Remove the sawn part with a hammer and crowbar.
5. Fill potholes and uneven areas with cement mortar.

When dismantling, the main rule is not to rush, otherwise there is a risk of damaging entire parts.

Stages of assembling a new pipeline

When replacing old sewer From cast iron to PVC, fittings and pipes are first assembled into one system. Then marks are made on the walls, taking into account the slight slope towards the riser. Clamps are attached to the marks. After this, the installation of a new pipeline begins:

1. Connect the assembled system to the sewerage inlet using a sealing collar. Make sure that no burrs appear in the cutting areas, otherwise this will cause permanent blockages.
2. To lead to plumbing equipment the pipeline is extended to the required length.
3. The tightness at the joints is checked.

Now you can use the new sewage system.

Features of repair of external sewerage

The difference between the sewer system of a house in the private sector is that it runs underground. If you need to replace part of the pipeline, you can do without dismantling. To do this, a new one of smaller diameter is laid over the old system.

During a major sewer repair, a pipeline with a defect is dug out and laid in its place. new system downhill Depending on the region of residence, choose a method of protection against freezing:

• laying to a sufficient depth;
• insulation of pipes with insulating materials.

When it is not possible to remove a leaking pipeline, the method of pressing into the ground is used. A new sewer is laid in the vacant space on top of the old sewer.

Basic mistakes when repairing a sewer system

It is possible to identify the cause of a sewer malfunction and repair it only with an understanding of how the system works. You cannot begin repairs without determining the material from which the pipeline is made. Otherwise, there is a risk of flooding neighbors and creating emergency situation, which will affect the entire house. Work should be carried out in strict accordance with technological process, following the sequence of actions.

Modern sewerage is a rather complex technical complex. Its primary task is to remove latrines and wastewater from a private house or apartment, which are formed in considerable quantities during the life of the residents. After all, in every modern apartment In addition to the toilet and sink, there are many other equipment in the kitchen whose waste is sent to the sewer network.

The individual elements of this network are connected together. Because of this, a rather confusing system is formed, which simply cannot function 100% flawlessly, without all sorts of breakdowns and other problems.

A problem can arise unexpectedly in any part of the pipeline, and no one can predict where the defect will appear. In most cases, urgent repairs sewer pipes made of cast iron (or plastic) have to be performed due to the following faults:

• Emergence unpleasant odors emanating from elements of the sewerage network. This clearly indicates that one or another element of the system has cracked. Or there is a major blockage in it - which is also a fairly serious problem.
• The occurrence of leaks directly at the joints of elements of the sewerage system;
• Pipe blockage (complete or partial).

The last of the above malfunctions is observed in domestic sewers very, very rarely, but still sometimes you have to deal with such a disaster. Typically, blockages occur in siphons located under sinks or sinks in the kitchen. A variety of debris is likely to accumulate in pipeline assemblies, especially in kitchen ones. Any person can remove it, and without the use of any equipment - just use the familiar plunger. A few confident movements with this simple device, and the blockage disappears in no time. The main thing is not to forget to thoroughly rinse the cleaned system with water, and under pressure.

In cases where the specific design of the sink requires the presence of a special hole that provides it reliable protection from excessive filling, in other words, from overflow, before using the plunger, it is imperative to close this overflow. Otherwise, you will continuously drive air through the sewer pipes. There will be no result. For the simple reason that the blockage will not go away.

You can also use a plunger in cases where the toilet becomes clogged in a private house or apartment for one reason or another. Here, however, it is important to note that the proposed solution to the problem does not always help. It is also possible that the plunger will have an effect, but not to the extent necessary. However, no matter what, it’s still worth trying to use this remedy. If the expected results are not obtained (that is, the clog that has formed remains in place), you must try to clear the toilet drain using chemical cleaning compounds. If this is also useless, then in any case you will have to use a special cable to carry out cleaning, and in some situations (for really complex blockages) you will need to call professionals “armed” with special equipment.

The quality of assembly of the sewerage system directly determines its service life. In addition, there is a high probability that sewer pipes will need to be repaired. But even the highest quality assembly will not be able to guarantee you a 100% probability of no accidents or any other urgent situations. Therefore, it makes sense to take a closer look at the basics that will make it possible to independently eliminate problems that arise with the pipes of the sewer system.

Common causes of breakdowns

The need for urgent repairs occurs in the following cases:

1. The appearance of leaks at the joints of pipes.
2. There is a crack in the pipe, which gives off an unpleasant smell.
3. There was a blockage in the pipe.

Let's look at each of the above cases in more detail.

Leakage at joints

This problem, in turn, can be of two types - a leak at the entrance to the pipe, or a leak at its junction. Depending on the level of breakdown, tactics vary somewhat.

Leak at inlet

The first step is to determine the place where the sewer pipe is leaking. The most common leaks are sinks, as well as bathroom sinks and drains. Connection defects that occur at the boundaries of the siphon and the drain hole are the most common cause. To resolve the problem, it is necessary to check the condition of the gasket and, if possible, replace it, and then tighten the connection where the leak occurs. Sometimes it may be necessary to seal the pipe entry area.

A leak that occurred at a pipe junction

If a leak occurs at the junction of pipes made of cast iron, the operation will be much more difficult than discussed above. Fixing a leak is determined by the type of connection: it may consist of lead or cement.

The sequence of necessary actions when cementing sewerage elements is as follows:

1. Use a hammer and chisel to remove the old cement.
2. The packing is removed along with the remains from the gap.
3. A new layer of packing is laid, after which a fresh layer of sealant is hammered in. All this is sealed on top concrete mortar. To prepare it, you need to take water and cement in a ratio of 1:10.

Professional recommendation: In order to increase the reliability of the seal, a special mixture is used to lubricate the strands of the seal. It is obtained from asbestos and cement (proportion 3:7) and water. It is necessary to add water exactly until the existing consistency of the mixture begins to resemble plasticine.

The sequence of actions for lead connection of elements is as follows:

1. It is necessary to clean the connection material until pure metal appears.
2. Using a chisel, hammer in new lead cones. Due to the fact that lead is a soft metal, similar recommendations will not be difficult.

Let's consider more difficult situation– how can you seal a sewer pipe, if of all necessary funds there is only cement, but for one reason or another there is no sealant? Make it real.

The algorithm of actions in this case can be characterized as follows:

• It is necessary to clean the joint, get rid of the old existing seal;
• Take a medical bandage, as well as liquid glass and cement;
• The cement solution, or rather, its desired consistency in the form of a slurry, is obtained by adding water. The importance of this consistency of the composition is explained by the need to dip the bandage into it. Adjusted for presence liquid glass The rate of hardening is significantly increased. This means that you should work at the fastest possible pace;
• We wet the bandage in the resulting solution and carefully wrap a thick layer around the junction point of the pipes;
• After 2 hours, it is permissible to hide cosmetic imperfections by painting over the defect area with paint.

If a leak occurs at the junction of plastic pipes, the only necessary measure is replacement rubber seal. Apply silicone sealant over the defect for greater reliability.

There is a crack in the pipe - what to do?

In this case, it will be possible to fix the problem only temporarily - anyway, the damaged pipe will burst sooner or later, and rather sooner. So you should hurry up with a replacement. But if such a possibility is not foreseen, you can get by with a temporary measure. The remedy for eliminating the defect is selected depending on the material of which the pipe is made.

IN polymer pipe(made of PVC) crack elimination is carried out by applying sealant and wrapping the defect area with tape (ideally, repair tape). This will get rid of the unpleasant odor coming from the sewer. But still, a complete repair of a sewer pipe with your own hands, without dismantling and opening it, will not work. But cast iron, due to its porous texture, makes this process somewhat difficult.

In such a case, the problem can be solved as follows:

1. Expand the crack as much as possible and thoroughly degrease the surface.
2. Make a 1.5:1 mixture of copper oxide and phosphoric acid.
3. Cover the crack with the resulting mixture as soon as possible.

There is a pipe blockage - what to do?

In such a situation, the same plunger will help. Open the water and make a vertical movement, placing the plunger directly above the drain. Usually these actions are enough to solve the problem.

The sewer system in an apartment or house must function properly. By conducting periodic inspections and taking preventive measures against breakdowns, you can achieve trouble-free operation of structural elements. But sometimes emergency situations do happen. It is worth knowing how to repair sewer pipes without opening and dismantling.

Required tools and materials

Leaking polypropyl new pipe at the junction

Recovery damaged areas sewerage is worth stocking up on necessary tools:

• paint brush;
• wire brush or sandpaper;
• hacksaw;
• construction knife.

In addition, it is advisable to have the following materials on hand:

• construction adhesive;
• cement;
• liquid glass;
• solvent or degreaser;
• bandage or tape made of fabric;
• clamps or wire;
• rubber.

These tools and materials are enough to seal a joint at a leak or repair a burst pipe. For overhaul It is worth purchasing pipes and fittings.

Causes of sewer pipe breakdowns

Crack at the junction of cast iron and plastic pipes

The main types of sewerage breakdowns are leaks. They usually occur at the junctions of structural parts, sometimes along the element itself.

Causes of leaks:

• High load on a single part. This usually happens when the system is clogged. High blood pressure inside the structure leads to damage in the weakest areas. The system can be restored to normal operation by mechanical or chemical cleaning.
• Freezing of structures in the winter time. Parts used outdoors are often susceptible to this. But accidents also happen inside buildings. Water expands when it freezes. Ice jam capable of tearing the material of pipes or fittings.
• Details Bad quality or improper installation of the structure also lead to the destruction of individual elements. This requires replacement of gaskets or repair of pipes and fittings.

Depending on the extent of the damage, urgent or major repairs of the sewer system are required.

Urgent pipe repair

Small leaks in pipes can be sealed with a special sealant

Cast iron structures are often found in old buildings. Breakdowns in such highways are not uncommon. In this case, it is difficult to replace a separate part. Leaks in cast iron pipelines are sealed using sealants.

Coating the leak site is often used construction glue with cement.

1. Use a wire brush to remove rust from metal parts.
2. The treatment area is degreased.
3. Apply a layer of construction adhesive with a brush.
4. Cement is poured on top.

Several more layers are performed in the same way. Then you need to dry the cement-adhesive patch. This method is effective for small leaks. In more serious cases, it is worth using another recovery option.

1. Perform pre-processing of metal parts.
2. The cement is diluted with water and liquid glass is added.
3. Soak the bandage with the resulting solution.
4. The material is wrapped around the leak site in 5-6 layers.
5. The top of the structure is treated with silicate glue.

There are several ways to carry out urgent repairs of plastic pipes without dismantling them:

• Using sealants - the dried and grease-free crack is covered with a waterproof agent.
• Using special tapes, the damaged area is wrapped with material in 2-3 layers.
• Using rubber and clamps - a rubber pad is placed at the leak site. It is secured at the edges with clamps.
• Using soldering.

Seal the leak in plastic pipe sewerage can be more in a radical way. For small ones, couplings are used.

1. Use a hacksaw to cut out the damaged piece of plastic.
2. The edges of the pipe are cleaned of dirt and degreased.
3. Sanded to create a rough surface.
4. Glue or sealant is applied to the ends of the elements.
5. Put on a muff.

Cracks larger than 10 cm are sealed using two couplings and a piece of pipe. The repair technology is identical to installing one fitting.

Major renovation

Textile stocking with epoxy resin creates a waterproof coating

If in a building with plastic sewer Water flows through the joints; it is not necessary to dismantle the entire system. Leaks in the joints of sewer pipes can be eliminated through major structural repairs. There are the following methods for this:

• Insertion of smaller diameter pipes into existing networks. To do this, you do not need to open the sewer pipeline.
• Restoring the integrity of pipes using a flexible insert made of textile stocking, which is impregnated with epoxy resin. This creates a new waterproof structure inside the old pipelines.

The use of new technologies makes it possible to repair old mains outside and inside the building without excavating trenches and dismantling the sewerage system.

Sewage repair on top floors buildings has some peculiarities. Here it is formed air bag from gases from wastewater. They are removed from the system via fan pipe sewer ventilation. For this reason, repair of damage is carried out with careful sealing. Otherwise, gases from the waste system will enter the living quarters.

Common mistakes when repairing a sewer system

The most common mistakes when installing and repairing drainage structures are the following:

• During installation, the wrong slope of the pipes is chosen. This leads to disruptions in the operation of the entire structure. A large angle of inclination promotes gradual settlement on inner surface parts of solid particles that are not completely washed off with water. Insufficient slope can cause siltation of the pipeline and the formation of traffic jams.
• Poor sealing of the joints between various parts quickly leads to the need for repair work.
• Often malfunctions are caused by the lack of inspections and ventilation of the sewer system - they are simply removed during renovations in the house.

To restore the functionality of the sewer system, you should not use corrugated pipes instead of siphons. They become clogged faster and more difficult to clean.

Preventive measures against sewerage breakdowns

To avoid having to repair breakdowns and malfunctions in the sewer system, it is worth taking preventive measures in advance.

• Must buy quality products with the required technical characteristics.
• When installing individual parts it is worth Special attention pay attention to the joints. They need to be well sealed.
• Parts of the waste system that are operated at negative temperatures. Here they use foamed polyethylene or a foam shell.

Properly installed waste system from quality materials able to serve for a long time and reliably. If necessary, you can repair sewer pipes without opening the structure yourself.

A breakdown of the sewer system in an apartment requires urgent and professional intervention from a specialist. On the website youdo.com you can order the services of qualified craftsmen who perform various plumbing work, including pipe repair. Private performers and companies are registered here, the cost of their services is low. Our specialists successfully cope with work of any level of complexity.

Sewer pipe repair services

Yudu performers successfully eliminate various breakdowns of old sewer pipes:

• flow
• blockages
• unpleasant smell from cracks

The specialist will be able to correctly determine the location of the leak and choose a method to eliminate it depending on the condition of the pipeline. It may be enough to change the gaskets or additionally seal the entrance to the sewer pipe. If the pipeline is made of cast iron, the technician will fix the leak using another method. Lead or cement is removed from the joint, the gap is cleaned, and after that lead or a winding of oiled tow is applied again and the place is cemented. To save yourself from problems with the old cast-iron sewer system in your apartment, order Yuda to replace it with a plastic one. This material lasts longer and looks more aesthetically pleasing.

Professionals registered with Yuda are ready to help if you need to eliminate a pipe crack. Usually the area needs to be replaced, but if this method is not suitable for some reason, the technician will coat the area around the crack with sealant and wrap it with insulating material. A lead cone is driven into a small-diameter through fistula.

If you were unable to deal with the clogged sewer pipe yourself using chemicals, a specialist will fix this problem using a punching cable.

Why is it worth ordering the services of professionals?

Ordering services experienced specialists has a number of advantages:

• The technician will select the correct method to fix the problem
• will carry out high-quality repairs of any sewer system
• will take care of the selection of materials

The technicians arrive when called with all the necessary tools. You can discuss the need to purchase a new pipe with a specialist. The contractors carry out other plumbing work and are ready to provide assistance if the connection of plumbing, boiler or household appliances is required.

When repairing pipes, professionals take into account all the operating features of the sewer system in your apartment. When cleaning a plastic pipeline, use only a cable with a plastic tip; it helps protect the coating from damage.

Yudu performers take into account the features of the plastic pipeline, so if it is damaged renovation work are not fulfilled, since the strength characteristics have already deteriorated, which reduces the reliability of the sewerage system. This section is completely replaced.

How much does a master's work cost?

On Yuda you can discuss the cost of repairing sewer pipes in apartments directly with the contractor. The price of the work will depend on:

• type of breakdown
• type of sewer pipeline
• need to urgently repair a faulty pipe

If the purchase of components is entrusted to a specialist, the price for them is included in the total cost of the specialist’s services. Performers must provide receipts.

On Yuda you can also order inexpensive plumbing connections and repairs, installation of new risers, and replacement of siphons. The work will be done efficiently, which will ensure trouble-free operation for a long time.