In this article you can see a video on how to make a homemade boat from a barrel with your own hands.
The video uses a 200 liter plastic barrel for technical needs.
This, of course, is not a homemade PVC boat, but it will do for fishing.
It often happens that a plastic barrel purchased for water leaks. It can no longer be used for its intended purpose, but with some imagination and a little straight hand from the old plastic barrel you can make a full-fledged homemade fishing boat.
To make a fishing boat with your own hands, you will need an unnecessary plastic barrel, plastic pipes for sewerage or electrical wiring, and the desire to make a homemade fishing boat.
Look at the video below, it shows such a homemade boat being tested.
As you can see, despite its very strange shape, it is quite possible to sail on such a homemade vessel on a lake or calm river.
At first glance it may seem that a barrel boat is very unstable on the water, but this is not so! Sealed pipes located on the sides give this hand-made boat not only additional buoyancy, but also stability.
By design, such a homemade boat is classified as a trimaran.
Of course, in the basic version, such a homemade product can only be used to sail a couple of tens of meters from the shore and quietly go fishing. Using a short rod. In this case, you can use a cheap echo sounder to detect fish and control the bottom topography.
If you want to put a motor on such a homemade boat, you will have to modify it.
Look at the video of the second version of a homemade fishing boat from a barrel.
)
As you can see, first of all, the improvements affected the increase in the number of pipes used on the side floats of the homemade trimaran. And the length of the floats has also increased.
Thus, the carrying capacity of the homemade boat increased and its longitudinal stability increased. This is understandable, the use of a motor not only introduces an imbalance when moving, but also increases the weight of the structure itself, because in addition to the electric motor for a homemade boat, it is also necessary to place a battery to power this propulsion unit with electricity.
The price of such a homemade boat is not high. Even a new plastic barrel costs about 1000 rubles, another 250 rubles will need to be purchased plastic pipes. To bend and wrap pipes, you will need a construction hair dryer; you don’t have to buy it, but ask your friends. All seams will need to be sealed silicone sealant, it will require another 150-250 rubles.
In total, a homemade fishing boat will cost you only 150 rubles! You will spend no more than one evening on construction; after 24 hours, the silicone sealant will completely polymerize and you can begin testing.
The advantages of such a homemade fishing boat include its light weight and small dimensions. It can be easily transported on the top trunk of any car, and carried to the water alone.
It will be very difficult to turn over such a homemade trimaran, so you can fish without fear.
By the way, according to Russian laws, any boat equipped with an engine of 5 horsepower or less does not require registration. So – explore the waters and fish to your health!
So it's worth reading the article
Before you start building wooden boat, it is necessary to prepare the main part of such a structure - the sides. To do this, you need to take the smoothest, longest, wide enough boards that are made of spruce or pine.
Look at the photos of homemade boats and you will see that there are no boards on its sides that have knots - this is very important. The boards for this part of the boat must remain in a dry place under slight pressure for at least one year.
Choosing boards for work
Before production begins, it is necessary to once again ensure that the boards are absolutely suitable for the job. Next, for each board you need to measure desired length and carefully cut them at an angle of 45 degrees. These boards will go to the bow of the boat.
After this, you need to plan them and check that the boards connected to each other do not have gaps. Then treat the ends with an antiseptic.
The next step is to prepare the bow of the boat, using a triangular block. It should be one and a half times longer than the width of the sides. The timber is also planed and covered with a layer of antiseptic.
Further instructions for making a boat with your own hands is to select a suitable board for the stern of the boat. Do not neglect the supply, because it is better to cut off the excess later than to search and start all over again.
Boat assembly
When the elements of the wooden boat are assembled, you need to begin assembling the product. You should start from the bow. Both sides and the triangular block must be connected to each other using self-tapping screws. It is advisable to immediately cut off the protrusions at the top and bottom so that they do not interfere in the future.
The next step is very important and responsible, since it is necessary to give the future boat its shape. You need to decide on the width of the boat and place a spacer in the middle. Choose a board for the spacer that is the same size as the height of the boat, so the sides will not burst.
Once the brace is properly installed, you can begin to shape the boat, call a few people to help or stock up on ropes to hold the structure in place.
Use the drawings and adjust the dimensions of the stern to make the boat so that when connected back wall and there were no gaps or cracks left on the sides.
When the backdrop is installed, cut off the excess part from below, and on top you can make an element in the form of a triangle. Next we work on the spacers, which will constantly maintain the shape of the boat, as well as the seats, which are installed on top of the spacers. You can determine the number, as well as the location of these elements yourself, so it can be one, two or more places.
We align everything on the bottom in one plane and process protective layer the entire surface. When the glue dries, start making the bottom of the boat.
The best option for the bottom would be a galvanized sheet of metal. Try to find a sheet that matches the size of the boat.
How to make the bottom of a boat with your own hands
Place the future boat on a sheet of metal and trace its boundaries with a marker, do not forget to take a few centimeters of extra space just in case, you can always trim off the excess.
The next step is to cover the connection of the boat with its bottom with a special silicone sealant along the entire length in one line. On top of the sealant, until it has dried, a cord is laid in several rows - all this is necessary to ensure that the bottom of the boat is airtight and does not let water inside.
When this process is completed, we move on to connecting the bottom to the frame. Carefully place the bottom of the boat over the bottom of the boat. Use nails or screws to connect.
Start connecting from the middle and move towards the edges of the boat. Do the work as slowly and carefully as possible, as this part is very important.
We cut off the excess metal that sticks out more than 5 mm from the edge of the boat, and bend the rest with a hammer. It is also important to protect the bow of the boat from external factors using the same metal. Cut a rectangle of tin to the size of the boat.
Wherever wood and metal are connected, it is necessary to go through with sealant and lace. By this time, before you start “wrapping” the bow with metal, you need to treat the entire boat with an antiseptic.
Be sure to make a fastening on the bow for the chain. This will help if someone wants to steal a brand new boat, since it will attract attention on a body of water. Special attention due to its novelty.
Before you build a boat, think through and look at all the ideas that you can use to make a boat. Perhaps you will choose a special material for yourself that will be more convenient for you to work with, or maybe you need special protection or massiveness.
Don't forget to cover the bottom with reverse side special paint, since galvanized metal is destroyed over time when in contact with water. The wooden parts of the boat must be coated with several layers of special impregnation and the boat must be left to dry in the shade.
For convenience, inside the boat on its bottom you can lay out wood flooring. This way the bottom will not rattle when you move along it.
At this point the boat will be ready. Read more articles on how to make the best homemade boats with a description in order to find out some other nuances that may be useful to you in future buildings.
DIY boat photo
Hunting and fishing are a favorite pastime of many men. Sitting with a fishing rod early in the morning in the reeds is a special romance for a fisherman.
Vehicles for fishing, and just for walking, are used in different ways - rubber, aluminum, boats made of PVC and even plywood.
You can buy absolutely any watercraft, if only you had the money, but how can you make a boat with your own hands? We'll tell you in our article.
Plywood boat
A homemade plywood boat is very light, easy to use and much cheaper than in a store.
The most important preparatory point in construction is the boat drawings. Having accurate calculations, in the future you will not have to waste time and effort on remaking and adjusting the product.
Calculations
We offer you one of the payment options. By transferring the drawings to paper, we will receive templates for all the necessary parts of the boat in life size. Now we can “cut out” our product and cut out the blanks with a jigsaw. Once you have all the cut out parts, you can start gluing.
First of all, we connect load-bearing elements structures, transom (cut of the aft part) and frames (transverse rib of the hull). Then the bottom and sides are attached to the transom, as in the photo of the boat.
To connect all parts, use epoxy resin and fiberglass tape. These materials will not only connect all parts of the structure, but will also create a waterproof seam.
Assembling the boat
Having secured the plywood to the side structures, you can proceed to strengthening the angles between the sides and the bottom. They do this using wooden corners, then move on to sealing the seams.
To obtain suture material, epoxy resin and Aerosil are mixed in equal proportions. Next, the seams are not just lubricated, but filled with this composition.
Once the entire structure has dried, you can attach the seats. If the boat has a motor, we attach the transom and bow cover.
The outer part of the boat also needs processing; it is necessary to glue all the external seams, also using resin and fiberglass tape, and sand the surface after drying. Then prime and paint.
Repairing damage to a PVC inflatable boat
If you already have inflatable boat and you actively use it, then moments of leakage probably often occur due to a puncture or cut in the material of the vehicle. Restoring a PVC boat is not at all difficult; it is easy to do in spartan conditions and even on the water.
Of course, to get a better result, you need to have time and do better repairs in a workshop. When fixing a leak, the glue dries, ideally, for 3 days, although there is nothing to worry about if you use the boat within a day.
If the boat was repaired on the water, upon return it is necessary to redo everything, since a hastily glued patch and without proper technology will not last long.
If a puncture occurs while fishing or hunting, use only the repair kit included with the boat.
Boat overhaul
For overhaul boats you need:
- Repair kit (included with the boat);
- Scissors;
- Roller;
- Pencil;
- Solvent promoting degreasing;
- Brush for adhesive.
Cut out a rounded patch from spare fabric. It should be 4-5 cm larger than the cut.
Note!
Spread the area to be repaired on a flat surface, clean it from dirt and degrease it with a solvent. Place the patch over the hole and trace with a pencil, coat both surfaces with PVC glue and let dry.
After 15-20 minutes, repeat the procedure and again give time to dry. After 5 minutes, the restoration itself can begin. Touch the surface of the patch with your finger; it should stick slightly.
Then, to activate the adhesive surface, you need to heat the patch itself and the puncture site; a hairdryer is ideal for this, just act quickly so that the glue does not dry out.
Now you can apply the surfaces to each other with the adhesive side, and carefully expel all the air, iron the patch with a roller. Then leave it to dry for at least one day.
In conclusion of our article, we can say that it is not necessary to spend a lot on buying or repairing a boat. With some effort, you can enjoy what you love.
Note!
DIY boat photo
Note!
An excellent alternative to an expensive boat can be a model made with warmth and love with your own hands. The review includes 8 interesting ideas for making a boat from scrap materials.
Plywood boat
boat from plywood sheets cost its owner only $59, and took about six hours to make.
Homemade sailboat
A sailboat with a double hull, each part of which is a different length.
Cardboard kayak for pool
A homemade cardboard boat for playing in the pool will delight any child.
Boat made from plastic bottles
Empty plastic bottles – economical material to make a functional boat.
Portuguese style boat
“I used the design of Hannu Vartiala, who kindly posted the boat plans on his website for free,” says the owner of the kayak pictured above.
Duct tape boat
Incredibly, ordinary adhesive tape can be used to make a fully functional boat.
Homemade sailboat
A sailboat made independently is much cheaper than its purchased counterparts.
Cardboard kayak under $40
A cardboard kayak, made in a certain way, is an excellent alternative to purchased models, of course, if the user does not intend to use it for professional purposes.
