The hasp is an integral part in the design of any of the varieties swing gates, which can be purchased at a specialized store, but is easy to make with your own hands. How to do this and what is needed for this - information that will be useful to many owners of private buildings.

What types of deadbolts are there?

Devices such as deadbolts are installed on swing doors mainly to ensure unauthorized entry into the site. And their main qualities should be safety and reliability. The appearance of the mechanism fades into the background, since it is installed from the inside of the yard and is most often hidden from prying eyes.

There are enough varieties of gates that you can make yourself, and choosing which one is most suitable for a particular gate is not difficult.

Pinwheel

This type of deadbolt is one of the easiest to make yourself, since it does not require welding. Its mechanism is arranged in such a way that the mount is located in the middle of the base of the device, and its “wings” lock both gate leaves when turning. This design is mainly used for temporary purposes.

Barrier

The mechanism of the “barriers” is similar to the structure of the “turntable”, but differs in that the fastening is located on one side of the bolt. Most often, this type of shutter is installed not from inside the yard, but on the street.

Espagnolette

The variety of such a shutter, as in the photo, is the most common, since its mechanism is used not only for locking gates and gates, but is also used for fixing the doors of vans, trucks and various doors. This type of deadbolt is available in specialized construction stores a wide variety of models that differ in size and design.

However, in the case of bolts for swing gates, where it is not too important appearance, the “latch” is most often done by the owners of the buildings themselves. Of course, if not we're talking about about valves with original forged handles, such as a ring or animal heads.

In addition to the above mechanisms, there are other popular types of deadbolts that are used to lock swing gates. These are types such as locking deadbolts and safe designs.

For reference! As a rule, “turntable”, “barrier” and “latch” type valves for additional protection to prevent unauthorized persons from entering the yard, they are equipped with padlocks.

How to make a “spinner”?

In order to make a bolt for a “pinwheel” type gate, you need a minimum of material, tools and time. The basis for the shutter can be wooden beam or a piece profile pipe, and the tools you will need are a drill, a grinder and bolts.

First of all, you should measure the middle of the base blank and make a hole in this place, the diameter of which should be suitable for the size of the bolt. Then the same hole must be drilled in one of the gate leaves.

After this, the workpiece is temporarily attached with a bolt to the sash to determine exactly where the brackets will be located. In this case, they must be fixed in such a way that one of them is directed with the open part up, and the other down. The base itself is installed in a strictly horizontal position.

The final stage in the manufacture of the “turntable” is preparing the structure for installing the lock. To do this, a hole is made in one of the brackets, as well as at the end of the pipe, which must be bent on the same side. After which we can assume that the locking device is ready for use.

Installation of a “barrier”

The principle of manufacturing a “barrier” type bolt is almost identical to the “turntable”, only the base clamps are located on one side, and all the brackets are attached with the open part up on both gate leaves.

Also considered one of the varieties of “barrier” is a loose slatted wooden beam, which is equal to the width of the gate. It is installed on 4 brackets, 2 of which are welded to the support posts, and the rest are fixed to the sashes in the middle. This system closes the gate securely and tightly.

How to make a “latch”?

To make a “latch” or, in other words, a valve, you first need to find a profile pipe blank and a metal rod of such a cross-section that it can move freely in the tube. For example, if the rod has a diameter of 10 mm, then it is better to select 2 pieces of pipe with sections of 15x15 mm and 20x20 mm, which will be inserted one into the other.

For reference! In this case, it is not at all necessary to look for a profile with a cross-section round shape, any length of pipe is suitable for such purposes.

To install the latch, 2 pipe blanks should be welded to the gate leaves. A metal rod is inserted into one of them, and then a handle is attached, which can be an ordinary bolt. The result should be a design that is similar in appearance to a regular door or window bolt.

How to make a locking lock?

Locking locks are mainly used not for entry into the territory of the gate site, but for fixation. Such a mechanism is usually installed in pairs - on top and bottom.

Many craftsmen use ready-made versions of such a device, left over after dismantling trucks. For these purposes, you can also use a piece of steel rod, which is bent and fixed with hinges on the gate leaves. To ensure that the latch holds the doors tightly in the closed position, holes are drilled in the frame into which the rod will fit.

Installing a safe deadbolt

The principle of operation of the mechanism is similar to the previous version of the shutter. The only difference is that not two short bolts are installed on the gate at the top and bottom, but one long one is mounted. The “fingers” of the device are tightly attached and, when locked, are captured by hooks that are welded to the ends of the rod. Thus, the gate is fixed in two positions.

Before you start making a gate bolt with your own hands, you should consult with experienced specialist. He will be able to advise which variety is most suitable for the design, taking into account all the circumstances of its use.

Gate locks are designed to simplify the process of opening and locking gates. They also provide protection to the area, as they make access to the yard strictly sanctioned. Modern latches are presented in a range where, along with traditional models, there are many automated and complex devices. The market for specialized goods is constantly being updated.

Design of a simple gate latch

For gates and wickets, new and improved latches and locks are regularly offered, which are equipped with additional secret codes security. A wide range of offers allows the consumer to buy constipations of any complexity category at an affordable price.

Those who prefer to make latches for gates with their own hands can use the most simple circuits devices that run from available materials.

The most common version of such a deadbolt is a wooden lock or a welded one made of metal. It is necessary to make a gate with your own hands so that operations that are repeated many times a day become as simplified and easy to use as possible. Most owners personal plots They prefer to install modern latches on wickets and gates, which are equipped with special anti-vandal options.

Such products are more reliable classic options. Their management can be automated. In combination with security systems Modern locking devices provide reliable control of the territory. Installation of the systems can be entrusted to professionals or done yourself according to the instructions included with the product.

Types of popular valves

Gate locks come in a wide variety of configurations. The most common valves that are easy to manufacture are:

"Spinner" for garage doors

The “Spinner” lock for gates with 2 leaves is most often installed on the doors of a utility room, garage or barn. Make your own high-quality constipation for swing doors possible without special effort. This device is a wooden bolt that is installed on the gate leaves, providing them with the tightest possible cover.

To make this latch, wooden beams with a thickness of at least 50 mm, but not more than 65 mm, as well as a channel and bolts are taken. The steps for making a latch are simple and accessible even to a novice home craftsman:

The only condition for installing such a deadbolt is the presence of a door or gate in the garage, which will provide access to the room from the other side.

Turntable design option for garage doors

The advantages of “Vertushka” are maximum connection of the leaves to each other, ease of installation, low cost of materials used and the absence of the need to install additional latches on the gate. This option is applicable for utility room, garage and barn gates due to the presence of a door block, against which the gate rests when closing.

"Spinner" for street gates and gates

If you arrange a semblance of a door block on the gate, then it will be possible to install a “Spinner” latch on it. This device is made with your own hands from materials available in any home. With minimal financial and time costs, the valve gives the most reliable and durable results.

To simulate a door block (upper “Pinwheel”) you will need:

• 2 metal plates from strip metal about 5 mm thick;
• hexagon screws (10 mm);
• drill.

Installing the top latch on gate leaves that open into the yard:

For the lower “Spinner” you will need:

• wooden beam approx 40X100 mm;
• bolt, 12 mm thick;
• 2 washers for bolt;
• stop rail (2 pcs.);
• self-tapping screws

Manufacturing of the main valve:

It is easy to make such gate locks with your own hands from available materials. As you work, you can always change or redo something to your liking.

Latch "Barrier"

The “Barrier” latch for wickets and gates is made from the same materials at hand as the “Spinner” latch. The only difference in the installation of this bolt is the nature of the fastening of the crossbar and one stop rail. So, the crossbar bar is bolted to one of the door leaves not in the middle, but at the end. In this case, the distance from the end of the sash to the crossbar attachment point should be about 80 mm.

The thickness of the bolt for the crossbar is calculated as follows: the thickness of the gate leaf and the thickness of the crossbar itself are added to the thickness of 2 washers. The bolt is screwed in with inside so that it cannot be seen from outside gate

Stop bars are installed on each of the gate leaves: one at a distance of 50 mm from the edge of the door, and the second along the length of the crossbar on the second leaf.

A latch must be installed at the top of the external gate, replacing door block. To make it, a thrust strip protruding from the surface of the door leaf is attached to the top of one leaf. And on the other side a movable pinwheel plate is fixed. It should be remembered that this arrangement is only suitable for swing doors that open into the courtyard.

Many men who own their own private lands try to constantly pay attention to their improvement. The face of any yard or garage is a beautiful entrance gate.

However, in this case, beauty is not the main thing; for such a product, reliability and protection from possible visits unwanted guests.

Such safety properties yard or Garage Doors provides a strong lock for the gate. This convenient door allows you not to open the massive gate leaves, but simply enter the garage or yard through a small opening.

A lock for it can be purchased at a specialized store or made with your own hands.

Types of locking structures

It is important to understand that any mechanical lock, unlike manual locking structures, requires keys. So you don’t have to worry about losing the key, because at any time you can securely close the gate or gate with your own hands using.

Today there are several types of locking mechanisms and different ones for gates, the most common of them are:

1. Installation direction:

• Vertical valves. A convenient lock that will ensure reliability and clear fixation of the wicket and gate. Most often, this type of shutter is used in swing garage doors. To secure the sashes, metal rods with handles are used, which are fixed in small recesses in the floor and ceiling.

In mortise gates, such gates are also used, only in a smaller size, and for their installation, metal clamps with a hole for securing the lock rod are welded into the upper and lower parts of the gate opening.

Yard gates can be locked in the same way, only a vertical lock can be installed in the lower part, and the fixation occurs thanks to a hole in the ground reinforced with a concrete covering.

• Horizontal latches. The most popular shutters that are used in all types of gates. The principle of operation is approximately the same as that of the vertical mechanism. The constipation itself has simple design made of a rod, a shell-holder and a fixing ear.

1. According to the functioning of the mechanism:

• Sliding type overhead locks. A simple mechanism that easily attaches to any material with a flat surface. Thanks to the reinforced flat rod, this type of latch provides even greater strength and reliability of locking the gate. The lock can be installed both from the outside and from the inside. To further strengthen the mechanism with front side can be used the padlock, which should be installed on the mounting ears.

• Screw valves. The screw mechanism is installed on the front side of the gate and is quite easy to use. It consists of a rod with a screw thread and a key base, which has a recess and a small pin. Using a special key, which has a corresponding recess and pin, the shutter mechanism is activated. You can easily make such a lock with your own hands. However, the complexity of such a device lies in the fact that in the wicket opening there must be enough space for a recess with a thread into which the rod itself will be screwed. In addition, such a lock is easy to break by selecting a similar key.

• Deadbolt lock with rack system. Such a shutter can be purchased in a store and only experienced master. It consists of a key with special recesses and a corresponding locking base. This design is particularly strong and durable, however, there is a possibility that the key can be counterfeited. Therefore, it is better to use some kind of additional lock to close the gate.

• Groove lock with rotating mechanism. Such a castle has simple design, and also boasts special reliability and protection from possible hacking. You can make it yourself, however, for this you will need professional knowledge, machines and tools. The principle of operation is that the falling key, when inserted into the keyhole, through circular movements, activates a gear mechanism that opens or closes the gate.

• Valves with spring-loaded fixation. These gates are used mainly on the inside and most often act as additional gate latches at the same level as the main lock. Their spring design allows the latch to be operated effortlessly.

• Mortise lock. One of the most common constipation, which is sold in any hardware store. To install it, you will need to cut a hole in the inner base of the gate. The reliability of such a lock is high level. However, due to the complexity of the mechanism, it is almost impossible to make it at home.

• Electromagnetic systems. Thanks to modern technologies such a mechanism can protect you from hacking forever. It can be purchased from specialized companies and to install the system, you will most likely need the help of specialists. With the help of a reinforced magnet that operates electronically, your gate will be solidly fixed when closed. The lock is opened using a suitable magnetic key.

• Code devices. Also a convenient and reliable type of locking system. The mechanism is activated by simultaneously pressing the buttons in accordance with a preset combination of numbers. For greater reliability, change this combination as often as possible.

As you can see, there is a large number of various locking systems that you can use to protect your yard or garage. Depending on the complexity of a particular mechanism, you can purchase a lock in a store or make it yourself. It all depends on your desire, experience, knowledge and level of cash savings.

We make the locking mechanism ourselves

You can build a lock for the gate yourself at home. For convenience, it is recommended to use the simplest mechanism in the form of a horizontal latch on a spring basis.

Before you begin, determine the location on the gate to install the valve, and use a tape measure and pencil to make precise marks. Now draw a diagram future design, the most complete and understandable picture is presented below.

Then get everything ready necessary materials and tools such as:

• metal plates of suitable size;
• steel rod with eye;
• spring;
• vice;
• hacksaw for metal;
• hammer, screwdrivers or wrenches;
• screwdriver, drill, welding machine.

First you should make a frame for the lock. To do this, take a metal plate and weld rod holders to it. Then attach the handle to the rod and insert it together with the spring into the finished frame. Now it's time to start installing the finished product.

If you have metal gate, attach the lock to the indicated location using welding machine or tighten the fasteners with screws and nuts.

Well, if you have a wooden gate, you can use self-tapping screws. Opposite the locking rod, in the corresponding place of the supporting post or gate profile, make a hole to fix the gate in the closed state.

Now your shutter is almost ready. However, you can only open it from the inside, so it is better to build a torsion bar mechanism. To do this, take a thin metal cable required length, make a small hole for it in the lower side of the gate.

Attach the cable to the eye of the valve, pull it to the outside through the hole and secure it somewhere in closed place. By pulling it, you can open the gate from the outside.

So, in self-production and installation of this important detail there is nothing complicated.

The main thing is that before starting work you need to make accurate measurements of the location for installing the future product, correctly draw up a design diagram and have a certain set of tools and materials with you.

There are many types of gate locks, and each has its own characteristics. There are also many ways to make a deadbolt for a gate and install it yourself. The process of making a bolt is divided into several stages. On sliding structures From corrugated sheets, in addition to electronic locks, latches and bolts are also installed.

Hasp for swing doors

Choosing the type of deadbolt

Types by fastening method:

1. Horizontal. Installation of such a bolt is carried out in the upper zone or in the center; it can also be installed at the bottom of the gate. The design resembles a large latch. It consists of several parts: an outer shell, a retaining loop and a movable metal rod. This type is called a “latch.”
2. Vertical. The bolts are similar to previous models and are located in the same places. But they move due to steel rods. They are often used in swing models. A photo of the deadbolt is shown below.
3. Additional. The valve is installed directly on the gate and platband from the outside. This bolt has average protection ratings. Its installation is carried out together with other locks.

Designs with a spring

Types by type of design

1. Bolt. This is the simplest type. It is often assembled with your own hands in a short period of time. Bolts for swing gates have high strength ratings. They will not open if there is a strong gust of wind.
2. Locking on the lugs. Even a non-professional can handle its assembly, but it’s easier to purchase a ready-made version. This model is made of durable steel. Such locks are often installed on garage doors.
3. Pin bolt. It can be made from scraps metal pipe. To install, you will also have to dig pins into the ground. The constipation itself is made from two half-meter fittings.
4. Hinged latch. It is made of 4 curved hooks and a steel plate. The latch can also be assembled from wood. This option also looks great on a gate.

Barrier

Ready-made models

1. Pen. It can be spring and rotary. It will be difficult to assemble the structure with your own hands. The lock consists of several loops and a curved rod with a spring. It is also installed on gates.
2. Padlock. It itself consists of a submersible and locking structure. They are locked with a key. CISA produces various electromechanical locks, you can choose the appropriate option on the website.
3. Mortise lock with code. This type The locking mechanism is divided into magnetic and electromechanical. It is quite difficult to install, but the design has high reliability indicators. A combination lock is often installed on warehouse gates.

Typical design for swing gates

When choosing a deadbolt or electric lock, you need to pay attention to the weight of the gate.

You can also buy automatic locks. CAME is the company that sells them. All models comply with GOST.

Read also: Lock for metal and wooden gates: swing and garage

Making locks for swing gates with your own hands

Today, there are several of the most common options for deadbolts for making and installing them yourself.

Vertical constipation

Simple constipation

Step-by-step assembly instructions:

• all parts for assembling the mechanism can be purchased at Leroy Merlin;
• a drawing is made in advance;
• the point for placing the lock, its location in the ground and the length of the rod itself are marked on the frame;
• two similar parts are made from several metal rods. The length of the part is chosen such that it can hold the canvas of the inlet parts in a closed state;
• short pins are welded in the upper area of ​​the gate; they will facilitate lowering and raising the device;
• The pin is driven into the soil to such a depth that the object is protected.
• recesses should be made using garden borer, while maintaining a diametrical position relative to the rods;
• a hook-hook must be attached to the sash frame by welding. It will act as a handle for the locking device. With its help, the mechanism is fixed after the structure has opened.

Constipation diagram

Bolt

Eat interesting way how to make a deadbolt. It is assembled using available parts. Do-it-yourself gate latches are assembled from a beam and 4 wooden handles. This design can be made in 1 hour. 2 profiles and wooden handles are screwed onto the vertical racks.

To make the structure more durable and reliable, it is necessary to insert a beam or massive board. The result should be a mechanical locking mechanism.

Deadbolt drawing

There is another method for assembling gate bolts with your own hands. For this purpose, profile trims and square-shaped rolled products are used. We either weld the structure or install it with bolts. A handle should be welded vertically to a calibrated rod, the length of which is 350 mm. At the same time, they retreat from the right edge by 200 mm.

Read also: Do-it-yourself latch and latch for the gate: bolts, constipations, photos and videos

From square profile you need to cut 3 pieces, their length will be 100–200 mm. They must be attached to a plate with holes for fasteners using welding.

The first two parts, which have square tubes, are fixed to the adjacent edges of the valves. The rod will pass through them. He's banning the gate. The free end for rolling is inserted into the third part of the square profile. It is used to stop the handle when the bolt is opened. This option is used for gates made of corrugated sheets.

Garage deadbolt diagram

There is another assembly method. In the upper zone, reinforcement is welded, its diameter is 15 cm. Another curved element will be pushed there, which is fixed using an anchor rod. At the same time, it is fixed to a piece of pipe of the required diameter. Another part is installed slightly below the center. After fixing the part, the bottom of the tube must be welded.

After installation, be sure to check whether the anchor rotates.

You should cut a hole in it with a grinder, into which a hot iron plate is inserted. The parts are fastened using bolts. On the second canvas you need to make a hook, behind which the plate will fit when the gate is closed. Watch the video below about installing such a locking mechanism.

In the shop

Pinwheel

Installation is carried out in stages:

A layout diagram of the mechanism is first drawn. Then a metal latch is installed on top of the swing gate. It will begin to rotate on the self-tapping screw. Its diameter will be 8–10 mm, and the cap should be hexagonal. The top latch is installed to increase the rigidity of the lock and prevent deformation and twisting of the valves themselves. It can also be used as an additional support.

Pinwheel

The size of the plank is 4.5x10x200 cm. It can be steel or wood, the thickness of the part is approximately 5 mm or more. The length must be chosen in proportion to the width of the sash. Most often it is 2/3 of the width of the gate.

1. In the central part, a through bolt is mounted from the inside to one of the leaves (left). Its circumference is 10–12 mm. You need to step back from the edge by about 6–10 cm.
2. The bolt should turn without effort, and 2 washers are fixed on it.
3. A locking groove is installed on the canvas itself across the entire width. A channel is used as it. The bar is fixed in it. The channel is ground down using a wedge, then the bar will easily fit into the groove.
4. A support rail is fixed to another sash (right). It will protrude beyond the sash by 10 mm.
5. The bolts located on the outside also grind down, making it impossible to unscrew them. With this lock you can keep the doors closed even in strong winds. It is impossible to break into the structure from the outside. Such a locking system is also installed on hangar doors.

Barrier diagram

An analogue of the “Turntable” is the “Barrier” latch, it is made of the same parts. You can also make it electromagnetic.

IN country house, in a garage or in a country house, constipations, bolts and latches are always needed. The simplest reliable garage deadbolt can be made from simple materials, which every garage owner will find in his toolbox.

Except mortise lock It is imperative to install additional locking mechanisms on swing garage doors that will protect the gate from burglary. The principle of such additional gate bolts is simple - a metal strip that rigidly fixes both gate leaves.

The mechanism for moving and fixing the metal strip of such a bolt can be different:

• crossbar mechanisms are reliable and convenient, but require regular lubrication;
• swing bolts;
• sliding with lugs for a padlock;
• spring valves.

You can actually make any of these constipations yourself using simple materials. Some simple locks are simply not available for sale, but they have been securing gate leaves reliably for centuries.

How to make a simple pinwheel deadbolt

Do-it-yourself “spinner” deadbolt for garage doors:

• a metal strip (5 mm) or a wooden beam can serve as a locking mechanism for double-leaf gates. The length of the strip or beam is 2/3 of the width of the gate;
• Such a turntable rotates on a bolt (12-15 mm) which is installed in a fixed gate leaf, approximately at a level of 60 - 70 cm from the ground, so that it is convenient to open and close the gate;
• on one and the other side of the valves, at a height of 60 - 70 cm, we weld two groove profiles into which the valve strip should freely fit when closed;
• distance - approximately in the center of each swing gate leaf - the strip in the closed position should protrude slightly beyond the edges of the retaining profile;
• In order for the bolt to easily turn on both sides, we put two washers on it.

Important. The outside of the head of such a bolt must be ground off and painted over so that it is not visible.

Barrier type bolt

The design principle is similar to a turntable bolt, only the locking metal strip is fixed not into separately welded narrow grooves, but into a channel that is welded across the entire width of the second gate leaf.

Additionally, you can weld eyes on the end of the channel and the locking strip so that you can secure the bolt with a padlock.

Sliding bolt for gates with fixation

If you can simply make a turntable or barrier with your own hands, if you have a welding machine, then it is better to buy a good, reliable gate valve for garage doors in a store. Depending on the material of the valves, you can choose the design and size of the valve.

The disadvantage of such constipation is that there is no strong fixation, with strong wind gate leaves made of corrugated sheets are twisted. Therefore, it is better to install three latches securing the doors at a distance of 50 cm from above and below and one in the center of the gate on the stiffening rib.

Vertical bolts

A vertical bolt is simply a fitting (12 or 14) bent on one side in the shape of the letter G, approximately 70 cm long. The principle of locking the doors with a vertical lock:

• Pieces of pipe must be welded to the gate leaves on both sides; the diameter of the reinforcement rod must fit into this pipe;
• We cement two more pieces of pipe into the garage floor on one side and the other - this is fixation for the shut-off valves;
• in the closed state, the fittings are fixed in the pipe, the gate cannot be opened.

To make it convenient to open the gate, weld fixing grooves on both sides into which you will insert the curved handle of the fittings of such a vertical bolt.

Espagnols

The design principle is the same as for a vertical bolt, only the fittings and the pipe along which it moves are fixed on the gate leaves in a horizontal position, approximately in the center.

For security, you can weld padlock lugs onto the hasp.

All of the above locks do not secure the gate leaves tightly. You need to install several simple valves or start making a more complex but reliable lock that tightly presses the doors.

Sea container type locking mechanism

A convenient design of a lock for swinging garage doors, which every garage owner will appreciate - no need to bend over and reach when opening and closing the garage door. It’s easy to make constipation yourself:

• on the pressing flap we weld ring clamps with a leg for smooth pipe, with a diameter of 15 – 16 mm. The first is at a distance of 20 cm from the top of the gate frame, the second is in the center of the leaf and the third is 20 cm from the floor;
• We attach two hooks on both sides of the pipe;
• We weld two clamps for hooks to the frame at the top and bottom;
• When turning the pipe, the hooks securely fix the pressing flap.

In the middle of the rotating locking tube with hooks, you need to weld a 30 cm piece of pipe - this will be a handle for conveniently turning the bolt. The principle of such a lock can also be seen in trucks - it fastens securely and hermetically.

Bolts and latches for plastic decorative fences and gates

Gates, wickets and fences made of modern materials, type plastic mesh chain-link (PVC) is beautiful, inexpensive and convenient. But what kind of lock can be installed on such gates and gates? If you choose a plastic picket fence for building a fence and the same gate, then the best option- magnetic lock.

Metal products are not suitable for such modern designs and they don't look very nice. A magnetic locks– reliable, durable and practical devices.

Attaching such a lock to a gate leaf or a gate is not difficult with your own hands. All parts are attached with self-tapping screws. As you can see in the photo, this locking device- The best decision.

How to weld a simple garage door

It’s easy to make a garage door made of galvanized iron with a lightweight frame with your own hands:

• draw a drawing of the future gate with all dimensions;
• first we need to make a frame, which we will install in the opening on which the swing gate leaves are attached;
• all blanks from metal corner for the frame, according to the dimensions of the gate drawing, we cut it immediately;
• welding is best done on flat surface, it’s more convenient to level all the parts;
• We lay out the corners and align the frame using a water level, where we need to place pieces of plywood or bars. It should be perfectly level;
• We weld all the elements and clean all the seams;
• corner pieces must be welded to each corner of the gate frame;
• We cook the second frame in the same way;
• try it on finished design into the opening and adjust to size;
• Now you can once again weld the corners on one side and the other and position the frame in the gate opening.

Before installation, the frames must be treated with anti-rust impregnation and painted. When the paint has completely dried, you can begin installation.

Having installed both frames on pins driven into the walls of the opening, we fasten both frames with metal plates - a step of 50 cm.

Welding gate leaves - according to the diagram in the photo, similar to welding the frame, you need to clean all the welds and do not forget to install stiffeners, the number of diagonals depends on the weight of the intended gate skin.

It’s easier to understand the process of making a garage door by watching a video.