Adhesive K-Flex K-414 price

Glue k-flex k-414 0.5 lt price 434.24 RUR

Glue k-flex k-414 0.8 lt price 620.07 RUR

Glue k-flex k-414 2.6 lt price 3632.54 RUR

Glue consumption
300 ml per 1 sq.m. surface to be glued.

TECHNICAL SPECIFICATIONS K-FLEX K-414

It was specially developed by Italian engineers for gluing insulation from foam rubber of the K-FLEX brand. Adhesive K-Flex 414 is resistant to ultraviolet rays. The surfaces glued together with glue 414 acquire the characteristics of the material itself.

K-FLEX K414 adhesive is one-component contact glue, which is based on polychloroprene rubber.

The adhesive is intended for gluing K-Flex thermal insulation and AlClad, InClad coatings. The optimal application temperature is 15-20 0 C. The glue is produced in metal containers with a volume of 0.2; 0.5; 0.8 and 2.6 liters.

When insulating cold surfaces, K-FLEX glue should be applied to the insulated surface and the surface of heat-insulating products. The consumption of K-FLEX K-414 glue in this case is 0.3 liters per m² of surface to be glued.

1. Application temperature affects viscosity and drying time.
2. High humidity affects the strength of the seam.
3. Temperatures below the dew point must be avoided.

In order to glue the seams of thermal insulation products, K-FLEX glue must be applied evenly to both surfaces to be glued. The surfaces to be glued can be connected within 3-5 minutes. When gluing seams, the surfaces should be pressed tightly together.

Application of K-FLEX k414 glue

The adhesive composition is mainly used in heating systems, drainage systems, water supply systems, and heating points. It is designed for gluing insulating materials, suitable for IC CLAD BK and SR or IN CLAD, AL CLAD coatings.

Glue K-FLEX K-414 It is resistant to external influences and does not lose its qualities under the influence of temperature changes and atmospheric phenomena. The adhesive composition is resistant to aging and has long term operation. Keeps its quality characteristics at temperatures -40…+105 °C. The viscosity of the glue at 23 °C can be in the range from 550 to 750 MPa, the density of the composition is 0.85 g / cubic meter. cm.

The use of glue is allowed at positive temperatures (from 5 to 30 °C). After applying the composition to the surfaces, they are firmly glued together and acquire the high-quality properties of the original insulating material. Guarantee period product - 1 year when stored at a temperature of +15…+25 °C.

K–FLEX K414 adhesive is a one-component contact adhesive based on polychloroprene rubber and is intended for gluing K–FLEX products and AL CLAD, IC CLAD SR and IC CLAD BK coatings.

Transportation and storage:

Adhesive K-FLEX K-425

K–FLEX K425 adhesive is a two-component adhesive based on polychloroprene rubber and a hardener.

Transportation and storage: At temperatures from +10 °C to +30 °C, avoid direct sunlight. It is allowed to transport products under negative temperatures, in case of freezing, the glue restores its original consistency and properties at room temperature within 24 hours, while the jar must be closed. Guaranteed shelf life in original containers is 12 months from the date of manufacture.

Adhesive K-FLEX K 467

K–FLEX K467 adhesive is a one-component adhesive based on polychloroprene rubber. The adhesive is “contact” and is recommended for installing foam and synthetic rubber on pipes and general surfaces located in heating and cooling systems.

Transportation and storage: At temperatures from +10 °C to +30 °C, avoid direct sunlight. Products can be transported at sub-zero temperatures; in case of freezing, the glue restores its original consistency and properties at room temperature within 24 hours, and the jar must be closed. Guaranteed shelf life in original containers is 12 months from the date of manufacture.

* - If the installation temperature is below +10 °C, you must contact the specialists of K-FLEX LLC.

Products are certified. The certificate can be downloaded

Designed for sealing seams protective coatings AL CLAD, IN CLAD And WHITE CLAD when placing objects outdoors.

Transportation and storage: At temperatures from +5 °C to +30 °C. The guaranteed shelf life of sealant in cartridges (0.290 l) is 18 months from the date of manufacture.

Products are certified.

The glue dispenser is designed for uniform and accurate application of glue. The main advantages are reduced losses, reduced amount of working time during the process of applying glue, high speed of glue application.

K-FLEX cleaner is a mixture of organic solvents and is intended for cleaning bonded surfaces, cleaning tools (brushes, spatulas, rollers) and diluting thickened glue.

Available in 1 liter containers.

Transportation and storage: At temperatures from +10 °C to +40 °C, avoid direct sunlight. Guaranteed shelf life in original containers is 18 months from the date of manufacture.

Acrylic paint on water based, odorless, easy to apply and dries quickly, does not pollute environment and does not fade. Used to cover insulation both indoors and outdoors, excluding UV exposure. Available in 2.5 liter capacity. Paint consumption is 0.45-0.5 l/m2 in two layers.

Transportation and storage:

Products are certified. The certificate can be downloaded.

Water-based acrylic paint, odorless, easy to apply and dry quickly, non-polluting and non-fading. Used to cover insulation both indoors and to repair the K-FLEX COLOR system. Available in 0.5 l volume. Paint consumption is 0.45-0.5 l/m2 in two layers.

Paint color - white, gray, beige, black, green, red, blue.

Transportation and storage: At temperatures from +5 °C to +30 °C, avoid direct sunlight. Avoid freezing. Guaranteed shelf life in original containers is 12 months from the date of manufacture.

Products are certified. The certificate can be downloaded.

Designed for punching holes in K-FLEX AL CLAD and PVC coatings for its further fixation with K-PACK rivets. Has a plastic handle.

Rivets K-PACK are made of PVC and are intended for mechanical fastening of longitudinal and transverse overlaps of PVC, AL CLAD and WHITE CLAD coatings.

Packaging (1000 pcs.)

Plastic clips are intended for temporary fastening of longitudinal and transverse seams of thermal insulation made of K-FLEX PE foam polyethylene to ensure complete adhesion of the taped insulation seams to each other.
Packaging (100 pcs.)

A special capping tape is necessary for neat finishing of the ends insulated pipes. For ease of identification of pipes in the system, plugs are produced in the following types: silver, gray, red, blue. End cap length 10 m.

Size, mm
18 x 32
23 x 32
28 x 32
38 x 42
48 x 42
58 x 42

Example 18 x 32: where 18 mm is the length of the petals, and 32 mm is the width of the blanking tape, installed at the end.

Designed for mechanical fixation of K-FLEX plates to non-horizontal surfaces.

The mounting knife is designed for cutting K-FLEX tubular material.
Allows you to make a smooth cut without torn edges.

Bag with tools for installation of K-FLEX materials

Equipment:

• Universal calipers for external measurements;
• Metal compasses, at least 400 mm long, in a case or with a protective cap;
• Assembly knife, with a steel, narrow, long blade of at least 300 mm with a rounded end;
• Utility knife, 150 mm, offset blades;
• Sharpening stone for sharpening knives 225 mm or musat (sharpening) with a length of at least 300 mm;
• A miter box having at least three cutting angles of 22.5°, 45°, 90° and a width work surface not less than 120 mm;
• Radiator brush, with short, stiff bristles, at least 38 mm wide;
• The brush is flat, with short, stiff bristles, 22 mm wide;
• Varnish marker, with round (bullet) tip white, with line width: 1-2 mm;
• Tape measure 3 meters, in a rubberized case with 3 latches.

Glue
Installation of all brands of thermal insulation and K-Flex coatings is carried out by adhesive bonding using a special glue. Detailed description For brands of adhesives, see the text below.

Very important!
The glue must be mixed before application, even if you used it yesterday.
After applying the glue to the material, you need to wait a short time (50-90 seconds). Glue applied to the surface of thermal insulation will dissolve it at the micro level and begin to polymerize.
When the dried glue reaches a state similar to the sticky layer on the tape, gluing can be done.
As a result of proper gluing, you will receive a “cold welding” type connection.

To reduce the drying time of the glue, as well as when gluing materials at temperatures close to 0°C, it is recommended to add up to 10% K-Flex cleaner to the glue

.
It is not allowed to install thermal insulation on tape without using glue; this is a violation of the technology for installing thermal insulation.
Carrying out installation work described in detail in the section

Cleaner K-Flex consists of a mixture of solvents and is used for cleaning surfaces before applying glue, cleaning glued materials from glue residues to give them aesthetically pleasing, cleaning tools, diluting thickened 414 glue or using it for gluing at slightly negative air temperatures.

Download

Specifications

ALCLAD, ICCLADSR, ICCLADBK.

Can be successfully used for gluing polyethylene-based thermal insulation materials, for example Energoflex, Tilit, Thermaflex

Characteristic	Meaning
Color and viscosity	Liquid from yellow to red color with viscosity 550-750 MPa, at 23ºС
	From -40ºС to +105ºС
	From +5ºС** to +30ºС* ** - the use of glue at slightly negative air temperatures is allowed, subject to its obligatory dilution with the K-Flex cleaner up to 15%. Be sure to consult our specialists about methods of application.
	~ 1 liter per 5 m2 of material when applying glue to the material, when priming and the surface to which the material will be glued, the glue consumption is doubled.
Insulation thickness, 6 mm	1 liter per 150 linear meters
Insulation thickness, 9 mm	1 liter per 130 linear meters
Insulation thickness, 13 mm	1 liter per 100 linear meters
Insulation thickness, 19 mm	1 liter per 75 linear meters
Insulation thickness, 25 mm	1 liter per 50 linear meters
Insulation thickness, 32 mm	1 liter per 35 linear meters
Insulation thickness, 40 mm	1 liter per 30 linear meters
Insulation thickness, 50 mm	1 liter per 25 linear meters

Adhesive K–FLEX 425 is a two-component contact adhesive based on polychloroprene rubber and filler and is intended for gluing coatings INCLAD and thermal insulation of the SolarHT brand.

Basic specifications

Characteristic	Meaning
Color, viscosity	Translucent liquid of light yellow color with a viscosity of 1350-1750 MPa, at 23ºС
Operating temperature range, ºС without filler	From -40ºС to +60ºС
Operating temperature range, ºС with filler	From -40ºС to +120ºС
Temperature of installation work, ºС	From +5ºС to +30ºС* *- application temperature affects viscosity and drying time. High humidity affects the strength of the seam. Temperatures below the dew point must be avoided. Optimal temperature application of glue in the range between 15 and 25 o C.
Approximate glue consumption for sheet material for single layer application, liter/m2	~ 1 liter per 4 m2 of material.
Approximate adhesive consumption for tubular silting, liter/linear meter
Insulation thickness, 6 mm	1 liter per 130 linear meters
Insulation thickness, 9 mm	1 liter per 110 linear meters
Insulation thickness, 13 mm	1 liter per 80 linear meters
Insulation thickness, 19 mm	1 liter 60 linear meters
Insulation thickness, 25 mm	1 liter per 50 linear meters
Insulation thickness, 32 mm	1 liter per 40 linear meters
Insulation thickness, 40 mm	1 liter per 25 linear meters
Insulation thickness, 50 mm	1 liter per 15 linear meters

Adhesive K-Flex 467 - winter

Contact adhesive based on polychloroprene rubber for bonding all brands of K-Flex thermal insulation and coatings ALCLAD, ICCLADSR, ICCLADBK.

Main technical characteristics

Characteristic	Meaning
Color and viscosity	Liquid from yellow to orange color viscosity 400-550 MPa, at 23ºС
Operating temperature range, ºС	From -40ºС to +105ºС
Temperature of installation work, ºС	From -15ºС** to +30ºС* *- application temperature affects viscosity and drying time. High humidity affects the strength of the seam. Temperatures below the dew point must be avoided. The optimal temperature for using glue is between +5 and +25 o C. ** - Be sure to consult our specialists about methods of use at subzero temperatures.
Approximate adhesive consumption for sheet material for single-layer application, liter/m2	~ 1 liter per 5 m2 of material
Approximate adhesive consumption for tubular silting, liter/linear meter
Insulation thickness, 6 mm	1 liter per 150 linear meters
Insulation thickness, 9 mm	1 liter per 130 linear meters
Insulation thickness, 13 mm	1 liter per 100 linear meters
Insulation thickness, 19 mm	1 liter per 75 linear meters
Insulation thickness, 25 mm	1 liter per 50 linear meters
Insulation thickness, 32 mm	1 liter per 35 linear meters
Insulation thickness, 40 mm	1 liter per 30 linear meters
Insulation thickness, 50 mm	1 liter per 25 linear meters

K-Flex K414 is manufactured specifically for the installation of K-Flex insulation materials; it is quite resistant to atmospheric influences and the aging process. Surfaces treated with glue are reliably and easily glued and acquire technical properties source material. K-FLEX K414 adhesive is a one-component contact adhesive made from polychloroprene rubber. This glue has a high degree of resistance to various influences and has a long service life. It is produced in metal cans of different sizes: 0.22 l, 0.5 l, 0.8 l and 2.6 l. The temperature for using K-FLEX K414 glue is from +5 ºС to +30 ºС.

Fix contact adhesive is based on polychloroprene. Does not contain aromatic additives Specially manufactured for use with NMC insulating materials. Has excellent adhesion to metal surfaces. Not applicable to painted surfaces, asphalt, bitumen and other oil-based surfaces. Used in more difficult circumstances where the insulation is subject to large thermal changes, for bonding shells and joints that have complex shape(for example, bends, elbows, tees, valves, and others). The optimal temperature for using glue is + 20 ° C. It cannot be used at sub-zero temperatures. Packaged in 0.5 l and 1 l cans. Recommended for polyethylene foam fabric.

K-FLEX K414 glue reliably and firmly glues surfaces. This glue must first be applied over the entire area to the required thermal insulation material, and then the glue is applied in an even layer to the surface that needs to be insulated.

Technical data of K-FLEX K414 glue:

The appearance of the glue is a red to yellow liquid.

The density of the material at 23°C is 0.85 g/cm³.

The viscosity of the material at 23°C is 550-750 MPa.

The drying time of the material is 5-10 minutes.

Application temperature is from +5 ° C up to +30 °C.

The open time of the material is 10-20 minutes.

The operating temperature range of the glue is from -40 ° C up to +105 °С.

The shelf life of the glue is 12 months. closed at temperatures from +15 ° C up to +25 °С.

K–FLEX K414 is an adhesive based on polychloroprene rubber and intended for gluing products produced by K–FLEX coatings IC CLAD SR, AL CLAD, IN CLAD, as well as IC CLAD BK.

K-Flex glue is a necessary component of the high-tech pipe thermal insulation system of the same name. There is a plant for the production of K-Flex elastomeric products in the Moscow region. This is equipped with last word technology production with strict control product quality.

Types of K-Flex glue

The adhesive composition is available in two versions:

• single-component rubber-based products;
• two-component, including filler.

Thermal insulation material of this brand is used:

• for insulation of pipelines in heating and water supply systems;
• for creating tight connections in air ducts.

We sell various packages of K-Flex glue, ranging from 0.22 to 2.6 liters. A variety of release forms allow you to purchase required quantity product.

Rules for using glue

• use at temperatures from +5 to +30 ºС;
• stir thoroughly before use;
• in case of thickening - dilution with K-Flex cleaner;
• uniform application thin layer on both surfaces to be glued, previously degreased and dried;
• strong compression of surfaces after joining.

The two-component composition is used in the same way.

Advantages of K-Flex adhesive

This material is in high demand among consumers due to its many advantages. Among them:

• economical consumption;
• reliable bonding of surfaces without changing the technical characteristics of thermal insulation;
• resistance to aging and influence atmospheric influences;
• rot resistance;
• waterproof.

Numerous studies have proven that bonded surfaces retain their properties throughout the entire period of operation, which is 20 years.

We offer to order K-Flex brand glue with delivery. TERMA-MSK company is official representative manufacturer, therefore forms the most favorable prices for these products. Call to place an order!