For operation on natural or liquefied gas. Gas burners are available in various technical categories, up to fully automatic microprocessor control. They have from one to several stages of operation and operate at different gas pressures in the line. Low level noise, economical operation, automatic control- these are the main advantages of operating a burner on natural gas. Like all technical devices, the gas burner requires periodic Maintenance and repairs, which can be carried out based on the table below of the main faults gas burners.

Burner malfunction and repair

Malfunction: The burner motor does not start.

• Possible reason: No voltage. Low voltage. Circuit break.
• What to do: Check voltage. Install a voltage stabilizer. Find a cliff.


• Possible reason: The red lockout lamp on the burner is on.
• What to do: Press the red lamp until it clicks.


• Possible reason: The air pressure switch is faulty.
• What to do: Check the operation of the air pressure switch.


• Possible reason: The safety thermostat on the boiler has tripped.
• What to do: Unscrew the cap and press the red button until it clicks.


• Possible reason: The boiler temperature is set to low.
• What to do: Check the set temperature on the boiler.


• Possible reason: The software relay is faulty.
• What to do: Replace.


• Possible reason: The capacitor is faulty.
• What to do: Replace.


• Possible reason: Motor is faulty.
• What to do: Replace.


• Possible reason: Low pressure natural gas in front of the burner.
• What to do: Contact the gas service.

Malfunction: The burner motor starts but stops during or after pre-purge and the burner lockout lamp comes on.

• Possible reason: Air pressure switch is faulty.
• What to do: Replace.


• Possible reason: The fan is dirty.
• What to do: Clear.


• Possible reason: The pulse connection of the air pressure switch is clogged with dirt.
• What to do: Clear.

Malfunction: The burner engine starts, the control voltage of the program relay to the ignition transformer is turned on, there is no spark, the emergency lamp lights up.

• Possible reason: Ignition electrode is dirty or worn, insulation is faulty.
• What to do: Clean or replace.


• Possible reason: Incorrect electrode position.
• What to do: Adjust.


• Possible reason: Ignition wire is faulty.
• What to do: Replace.


• Possible reason: Transformer faulty.
• What to do: Replace.

Malfunction: The burner motor starts, after the purge is completed, a malfunction occurs: the emergency lamp lights up.

• Possible reason: Gas valve does not open.
• What to do: Replace the defective part.


• Possible reason: Open circuit or damaged wire.
• What to do: Repair the damage.


• Possible reason: Air in the gas pipeline.
• What to do: Blow out the gas pipeline.

Malfunction: The torch lights up, the burner stops, then restarts.

• Possible reason: Low gas pressure.
• What to do: Contact your local gas company.


• Possible reason: Pressure regulator does not work.
• What to do: Replace gas fittings.


• Possible reason: The filter in the gas fitting is dirty.
• What to do: Clean the filter.

Malfunction: The burner motor starts, a flame appears, then the burner stops and the emergency lamp comes on.

• Possible reason: The ionization electrode did not “detect” the flame.
• What to do: Check the position of the electrode and adjust if necessary.


• Possible reason: No flame signal.
• What to do: Check the correct connection of the phase and neutral of the supply wires, as well as grounding. Adjust if necessary.


• Possible reason: Flame detector is faulty.
• What to do: Replace.


• Possible reason
• What to do: Replace.

Malfunction: Engine shutdown during pre-purge.

• Possible reason: Software relay is faulty.
• What to do: Replace.

Malfunction: Engine shutdown during stop stage.

• Possible reason: The torch does not go out, there is a leak in the valves.
• What to do: Clean or replace.


• Possible reason: Software relay is faulty.
• What to do: Replace.

Malfunction: Formation of soot in combustion products.

• Possible reason: Incorrect air adjustment.
• What to do: Adjust.


• Possible reason: Insufficient draft in the chimney.
• What to do: Check the chimney.


• Possible reason: No supply or insufficient air in the boiler room.
• What to do: Check the supply ventilation.

Malfunction: Heat exhaust flue gases.

• Possible reason: Soot deposits on boiler heating surfaces.
• What to do: Clean the boiler.


• Possible reason: Gas consumption is too high.
• What to do: Adjust gas flow.

The data is provided for indicative information only. All work with gas equipment, such as gas boilers, wall-mounted geysers and other water heating and heating devices, must be carried out by specialists who have all permits and licenses for working with gas and gas equipment. And the most important thing is to have experience working with such equipment, which will help you avoid common mistakes that can lead to the most negative consequences.

The burner is the most important element any gas boiler, its “heart”, the stability of which directly affects the efficiency of the entire system. A correctly selected, installed and configured gas burner ensures uniform and complete combustion of fuel, and any, even small, malfunction in its operation can lead to serious consequences. Any gas equipment is a potential source of danger, and if it is not corrected in time, for example, “priming” of the burner, this can lead to the accumulation of gas in the room, which can cause poisoning and explosion.

Reasons to contact a specialized service center include increased fuel consumption, increased noise, repeated blocking of the device and the appearance of a gas smell.

A large assortment of burners of domestic, European and Asian production presented at Russian market, allows you to select the unit that optimally meets your requirements and financial capabilities. However, such diversity requires people carrying out repairs and service maintenance, thorough knowledge of the design and features of many models. And if a master who does not have special skills and expensive equipment can still cope with removing carbon deposits or cleaning the burner domestic production, then a non-specialist trying to repair high-tech Viessmann or Buderus equipment can, at best, lead to a decrease in the efficiency of the system, at worst, to a serious accident.

Our Center offers professional repair and maintenance services for any models of gas burners: from economical and reliable Baxi, Beretta, Ferroli, Protherm, Dakon to the most modern and expensive Viessmann, Bosch, DeDietrich or Buderus. We are ready to provide both one-time assistance in the event of an accident and take on long-term obligations. We are equally responsible and professional in repairing simple single stage burner, mounted on a household wall-mounted boiler and modulated, responsible for the operation of an industrial cascade installation.

Extensive experience working with various heating equipment showed that the most common reasons calls to the service center include poor-quality installation, non-compliance with the manufacturer’s requirements for operating conditions, natural deposition of combustion products, wear of parts during operation and irregular servicing of gas burners. To avoid downtime and costly repairs, we recommend regular checks and technical inspection of boiler equipment, including the gas burner. This will allow you to identify even the smallest faults in time and prevent them from developing into a serious problem.

By contacting the E-Tech service center, you entrust the “heart” of your boiler to professionals who can quickly and efficiently deal with any problem

Our specialists have at their disposal the most modern equipment and tools for diagnostics and repair work, including high-precision gas analyzers and PCs with the necessary software.

Thanks to our own fleet of service vehicles, the repair team will arrive at the scene of an accident as soon as possible, carrying a set of the most popular spare parts and consumables.

In case of absence necessary details, they will be quickly delivered from our 24-hour warehouse.

If it is impossible to eliminate the cause of the accident at the facility, the equipment will go through the entire cycle of necessary measures at our repair base.

All types of work and materials used are provided with an official guarantee service center E-Tech.

Gas burner TORCH WS-502- professional portable
gas burner which is used as a source of directional
flame with a torch structure, in which the flame temperature in the zone
the main flame reaches 1300°C.

Professional portable gas burner with piezo ignition for
standard propane-butane cylinder 220 g. (0.5 l). Length 150 mm.
Nozzle diameter 18 mm. Fuel consumption 120 g/hour. Power 1.65 kW

It was purchased from the Gearbest.com store with a 5% discount
ye. Arrived in Ukraine in just 6 days and delivered directly into your hands by courier.
The product was ordered on September 20, on the 22nd of September it was sent and already
On the 28th the parcel was received by Nova Poshta courier. Pleasantly surprised
To be honest, the delivery speed of this store.

IN hardware store I bought a gas cylinder for 1.5 euros.

It was packed in a blister on a cardboard and a standard white bag.

Main characteristics:

Flame temperature approximately 1300-1450°C

Automatic piezo ignition

Energy carrier – gas cylinder chik 220 g

Adjusting the flame intensity

Ergonomic design

A portable gas burner is used for a wide variety of jobs:

For soldering and welding low-melting metals and alloys (lead, tin, zinc, copper, aluminum, gold, silver, etc.);

Melting and welding of glass and plastic products, including plastic pipes, synthetic cords and cables.

For heating various objects, for example, to facilitate the loosening of “seized” threaded connections;

For defrosting locks.

To remove old paint;

To start a fire (fireplace, bonfire, grill, barbecue);

For singeing carcasses poultry, as well as game for hunting;

For defrosting food (meat, fish);

In farming and gardening;

Widely used in workshops, for various works in garages, laboratories;

When sewing clothes;

For architectural decoration.

Connection to the can:

Turn the orange button clockwise. Connect the gas
burner to gas canister and press. Then, to secure
can, turn the gas burner approximately 25° clockwise.

Ignition:

Hold the gas cylinder straight. Turn the orange button to? ? ?
turn counterclockwise and press the button to ignite.
The intensity of the flame can be adjusted.

Stopping the burner:

Turn the button counterclockwise until the flame goes out.

Precautionary measures:

1. Do not point a running gas burner at people or animals.

2. The burner nozzle is very hot during and after operation, so do not
touch it and do not touch it to flammable
materials.

In principle, there is no point in disassembling this burner, since there is nothing interesting there, but for amateurs I removed the casing)

Who cares? video review of gas TORCH burners WS-502C

Customer Service. Check out 24 hours a day.

Our company repairs, adjusts, cleans and diagnoses diesel and gas burners. The following manufacturers; burnersLambordgini, Cuenod burners, Gierch burners, Roca burners, Weishaupt burners, Riello burners, Ferroli burners, Bentone burners, Ecoflam burners, Fbr burners, ACV burners, Hansa burners, CTC boilerand other manufacturers. You can get advice and call a specialist by calling us.

Gas burners are one of the main parts of fuel boilers. They are used to burn fuel directly, and their failure has a very detrimental effect on the heating process. Or rather, it disables the entire system. A timely service inspection of the device would help avoid this, but it is not available to everyone. And in this case, the repair of gas burners offered by our company will come in handy.

What can cause the failure of one of the most important parts of a fuel boiler? There may be several reasons, and the most common is irregular technical inspection. The lack of timely ability to identify problems entails the need to repair diesel burners. In addition, this causes a violation of the optimal operating mode of the device, a decrease in efficiency and an increase in thermal loads.

Of course, many owners of fuel boilers would like to avoid such consequences, which means that regular technical inspections become really necessary. Without it, it will be difficult to imagine the trouble-free functioning of the main element of the fuel boiler, but with it it will no longer be inevitable urgent repairs burners

But this is far from the only reason for equipment failure, which is sometimes difficult to understand without a specialist. The cause of the breakdown may also be incorrect use of the fuel boiler, which completely crosses out all operating rules. Careless use of the device will inevitably lead to the need to replace any parts and repair gas burners.

And do not forget that contamination of fuel boiler parts can also cause an early breakdown. Timely maintenance, which will include cleaning, will again help to avoid such an outcome. But many people don’t take this into account and hardly know how to avoid a breakdown, hoping that it will simply bypass it. Then renovation work will be inevitable, and it is better to produce them in a company that knows what it is doing.

Burner repair by professionals

Service	Price
Visit of a specialist for diagnostics inflatable burner up to 90 kW.	1500 rub.
Cleaning the boiler with a diesel burner	from 5000 rub.
Diagnostics of automation and adjustment of one circuit	1500 rub.
Setting up a gas inflatable burner up to 90 kW. With a gas analyzer.	6000 rub.
Setting up a diesel inflatable burner up to 90 kW. With a gas analyzer.	6000 rub.
Repair of inflatable (gas, diesel) burners up to 90 kW. No spare parts for the burner.	4500 rub.
Gas setting modulating burner (Weishaupt type)	11000 rub.
Work performed at night increases

In our company you can order an employee to visit the site of the breakdown. And we will give you confidence that all work will be carried out by specialists and not by amateurs. Our masters have many years of experience, and therefore they repair diesel burners not only within an acceptable time frame, but also in such a way that you do not have to turn to professionals for help too often.

But someone might think that it would be easier to buy new equipment rather than carry out repair work. But in reality it will be more difficult and costly. To purchase this or that equipment, you need to find exactly the model you need. And such searches can take a decent amount of time. So why waste it practically in vain?..

And if a model similar to the previous one cannot be found, then someone decides to offer to buy completely different equipment. But you will need to get used to using a new fuel boiler, which will also take time. So why break the usual routine when, instead, you can repair failed gas burners through specialists?..

It will be more a good decision, which will save you a lot of time. In addition, this way you will significantly reduce your costs. Yes, since a malfunction has already been discovered, it will be easier to fix it. But replacing the entire equipment is worth it big money, and in comparison with this, repairing burners will be a very cheap pleasure.

One way or another, the work of specialists, as a result of which your fuel boiler will return to operation, will be justified. And modern equipment and labor experienced craftsmen will convince you that the problem was not as global and terrible as it initially seemed. And everything to avoid a recurrence of such a situation in the future is a timely service inspection and correct operation fuel boiler and burners. This will save you from unnecessary worries and costs. And our specialists, who carry out any work around the clock necessary work with fuel boilers will help you achieve the best and regular performance of your equipment.

Our specialists will help you select, install, configure and launch high-quality equipment that in the future will not cause a lot of hassle and problems with setup and repair. We work with boilers and burners Baxi, Vaillant, Viessman, Protherm, Buderus, DiDietrish, Ferolli, ACV, Weishaupt, Gierch, Hansa, Lamborghini, Oilon, Cuenod, Fbr, Ecoflam, etc.

Our service center provides 24/7 burner repair, boilers and boiler equipment in Moscow and the Moscow region.

Certified engineers of our company carry out quality repairs diesel burners and gas burners of any complexity in the shortest possible time.

In order to identify a defect, a service engineer diagnoses the equipment, after which he reports the cause of the malfunction and a work plan to eliminate it.

Cost of on-site and diagnostics for burner repair

Service	Daily rate, rub	Weekend tariff, rub
Engineer visit service department within a small concrete ring	1200	1400
Travel outside the Small Concrete Ring (per kilometer)	35 rub/km	40 rub/km
Carrying out diagnostics (identifying the causes of the malfunction)	1000	1000
Other works

The day rate is valid from 8:00 to 19:00 from Monday to Friday. Weekend rate is valid on weekends and official days holidays. When the service center is overloaded at night and evening time an additional increasing factor may be introduced for work. The size of the coefficient is specified by the operator when placing an application.

Guarantees

The company is responsible for the quality of the services provided, and gives a 6 month guarantee for the complex of work performed.

By contacting us, you acquire qualified assistants in the repair and maintenance of boiler equipment, gain peace of mind and confidence in your work. safe operation engineering systems your country house.

• Low prices for work and spare parts;
• Promptness of departure and execution of the application;
• Service specialists have more than 5 years of experience;
• Spare parts are always available in stock;
• Service engineers are trained in authorized centers of manufacturers.

Our certificates

VIESSMANN Certificate

VIESSMANN Certificate

VIESSMANN Certificate

How we are working:

1. We accept your call;
2. A service engineer arrives;
3. The service engineer repairs the burner;
4. Cleaning the workplace;
5. Issuing recommendations;
6. Warranty service.

Inflatable boilers and burners

If we divide boilers according to their complexity, the variety of devices they contain, the complexity of diagnosing faults and repairing them, then the least problematic boilers are floor-mounted atmospheric boilers, then wall-mounted, and the most complex are floor-mounted inflatable ones.

Inflatable floor standing boilers consist of two main parts:

- boiler body;

- inflatable burner.

The body of the boiler is, roughly speaking, a cylindrical container into which a flame of combustible fuel is inflated with a burner. The boiler has simple sensors and regulators for the automation system. The boiler body is also a heat exchanger, through which the thermal energy of fuel combustion (gas, diesel, fuel oil) is converted into thermal energy coolant that circulates in its (boiler) walls.

However, the heart of an inflatable boiler is the inflatable burner.

— The burner contains basic automation elements, sensors, and a control unit for the entire boiler.

— The main operating modes of the boiler are configured and regulated in the burner.

— The fuel-air mixture and environmental parameters of fuel combustion are adjusted and prepared in the burner.

— The burner generates diagnostic signals for faults, errors and malfunctions of the boiler.

Repair, adjustment and tuning work is the most expensive and time-consuming - on an inflatable boiler. The most expensive spare parts are for the inflatable burner.

Therefore, all recommendations for the operation of boilers (link to articles on the operation of boilers) for an inflatable boiler are especially important. Compliance with them affects the proper, durable and safe operation of the burner and the boiler body, and affects fuel consumption.

Photo gallery of our works