Anyone can make a laser level, but you need to carefully study the theoretical part of the process Electronic laser level is one of the most necessary tools, which are needed both by builders and people of other professions. While using this level, you can project the intersecting points and see if you get a right angle. Buying such a device in a store can reach up to 100-200 dollars, and if you spend a little time and effort, creating a homemade laser level will cost pennies.

How to make a level at home: preparing materials

The cost of a laser level is quite high, and if you plan to use it only a few times, then such a purchase will be inappropriate. Therefore, you can do it yourself.

This tool will come in handy when construction work :

• During installation of floor and wall tiles of different sizes;
• When pouring the floor with concrete or other material that requires uniform distribution;
• When pasting wallpaper, both on the walls and on the ceiling;
• During installation suspended ceilings and windows.

Materials for making a laser level can be ordered online

Making a construction laser level with your own hands is not difficult. A

In terms of its qualities, it is not inferior to the purchased one; you only need to prepare some materials.

Namely:

• Cheap laser pointer, sold in any children's stores;
• A small piece of porous rubber, preferably thick enough;
• Regular bubble level of small size;
• A sanded block of wood the size of a matchbox;
• A small, flat stick that serves as a support;
• A bar corresponding to the length of the level;
• Small piece plywood sheet size 10 by 10;
• A clamp corresponding to the diameter of the pointer - it is necessary to secure it;
• The required number of screws.

After preparing all the materials, you can start working.

Homemade laser level: instructions for creation

Following the advice of experts, you can make a homemade laser pointer-level in a short period of time.

A homemade laser level is not inferior in functionality to those produced at the factory

5 important points in preparation:

1. When starting work, you must first remove the area of ​​the pointer where the insert with the pattern is missing, this hole is sealed with cardboard, where a small hole is made, then the cap is carefully installed in its place.
2. These procedures are necessary to achieve a clearer point while pointing.
3. An ordinary stick needs to be sharpened at the end to form a stake; it will serve as a leg for the level, and plywood is fixed on top of the flat base. This must be done accurately enough so that the angle corresponds to 90°.
4. On top, on the surface of the board, a strip is attached, having the same length as the bubble level. It must be installed using a screw so that it can be rotated different sides.
5. The final step is to attach the laser pointer to the bubble level, using a clamp and porous rubber; if there is a need for a cut, then make a recess.

Having done everything necessary instructions, we need to get to work.

Instructions: how to make a tripod for a laser level with your own hands

You can make a homemade tripod pointer different ways: with magnetic mount, where there is also a ruler; using a cross tripod; using straps for fastening. The most commonly used mount is the use of a tripod from an old camera, onto which a rotating mechanism from an old player is attached. Top installed old disk, onto which laser pointers are attached crosswise.

A tripod for a laser level can be made from any material: wood, metal

This method is perfect if you need to accurately install a painting or hang cabinets correctly.

If you need to quickly make the necessary marks while working, but don’t have a laser pointer at hand, there is step by step guide, to create a disposable level yourself, without using a tripod.

To make a similar pointer, which is designed in the most in a simple way, and has a self-leveling element, it is necessary:

• Prepare a small bowl or bucket of water;
• Take a piece of polystyrene foam in the shape of a rectangle and secure the laser pointer with an elastic band;
• The water container is set to a certain the desired height, foam with a pointer is lowered into it, then it must be turned on.

After a few minutes, the water will calm down and by moving the foam you can get ready-made dots.

DIY laser level: proper use

It’s not enough to make a laser level at home, you also need to know how to use it. You need to fix the stick with the sharp end down on the desired surface, then using a bubble level, level the angle of the bar to achieve the most accurate horizontal position. You need to turn on the laser pointer and carefully point it at the desired surface.

Before using the laser level, you should watch the training video and study the instructions for use

After the pointer appears, you need to make a small mark, then move the pointer a little to the side to accurately check whether the level mark has gone astray.

Once there are two points, you need to draw a horizontal line connecting them. If the result is a perfectly straight line, the level is working and installed correctly. The dots indicate whether the stand and stand are installed perfectly. When working with such a device, it is better to have safety glasses to relieve eye strain. Adjustment will be even faster if you use a plumb bob to help with the work. A homemade laser level has a bit of a primitive design, but the ability to save a decent amount of money mitigates this problem.

Experts highlight a number of advantages that a home level has:

• The beam length is sufficiently long, allowing it to be used in almost all work related to repair and construction;
• A small level of error, which is an insignificant drawback;
• High speed of marking and convenience, which a regular bubble level does not have;
• But builders highlight the main and most significant feature - the ability to project rays in a horizontal plane.

The homemade device can be used in future work; it will serve faithfully during the construction of the fence; if necessary, mark the boundaries on personal plot, during the cladding of any structure. Professional workers will need purchased levels, they come in these types. Bubble - it is a plastic or wooden case with three flasks inside. Each of them is filled with alcohol and has a bubble, it should be located in the middle, indicating the exact location.

Water - they are a hose of small diameter and up to 25 meters long, with two flasks, all elements are connected to each other. Each flask has a printed scale; such a device has both advantages, in the form of low cost, and disadvantages - you need to be careful when pouring liquid, and it only works on horizontal surfaces. Magnetic - their advantage is ease of mounting - it is quickly and firmly installed on any metal surface and gives accurate readings. Tubular - it is made in the form of a rectangle and is equipped with a magnet and a cord. Laser - it's different high accuracy, range, but has one significant drawback - high cost.

How to make a laser level with your own hands (video)

Each of us decides which level to use. We described all types of devices and revealed the principle of manufacturing the simplest device. The choice is yours.

Similar materials

ADA Silver. It comes in two versions. With and without a tripod. The tripod allows you to work without resting on the ceiling and outdoors (when there is no strong wind :-))

Where to place the rod: at home or outside?

If you're looking for a traction bar, this should tempt you. This is actually a Roman chair. This type of device allows you to achieve a greater variety of exercises compared to a conventional traction booster. Nothing beats bodybuilding or cross-training outside. But you will need to take the weather into account, and unless you live in an area where it never it's raining, weather will be a limitation. However, you can attach the rod to the wall of your covered patio.

The advantage of a bar is that you can exercise whenever you want. You won't have a view of your garden and you won't be able to breathe fresh air, but at least you'll be sure to stay dry! Attaching the door pull is really not difficult since you have little or nothing to do. You just have to be sure to place it on a frame that will support your weight.

The difference in price, by the way, is small. Without a tripod, a telescopic rod costs approximately 2,000 rubles. With a tripod it costs 200-300 rubles more.

I'll test the barbell without the tripod today.

The spacer bar comes in a convenient bag with a shoulder strap. Consists of 5 threaded elbows, a movable platform and 2 support heels. The knees are numbered, on them centimeter marks applied.

For a wall panel it becomes more complex. You must be a minimum master. It is secured with an ankle and screws. Think about this also to make sure for your safety that the wall or ceiling can support your weight, weight and a lot of tensile forces. Here are our tips to fix your bar in the best possible way.

You must determine the height at which it should be installed. To do this, know that your body should not touch the ground when your arms are extended and your knees are bent. You must be able to access the bar without jumping. The space between the rod and the ceiling must be sufficient to allow the head to pass over the rod. Face the wall and extend your hand. Make a mark in the middle of your arms and draw a line at that level. Check horizontality with a level. Using a suitable drill bit, you should now drill the mounting holes in the wall. Using a hammer, simply press the holes Anchors adapted to support in the holes Now place the bar on the anchors and screw the rod!

The first knee is telescopic, with rotary fixation. It also has a spring, thanks to which it is convenient to install the rod in the spacer. The maximum height to which the tripod can be expanded is 3.6 meters. If you have a tripod, you can place the level even higher.

Where to buy a traction bar at the best price?

By following these steps, you can make your activities safe and secure. optimal comfort use. But keep in mind that the price of traction in Intersport or other is often high. The selection is wider, the invoice is smaller, delivery is fast and the quality is on target.

The pressure level is adjusted to the spray nozzle. Replace the thread high pressure detergent in operating mode without replacing the spray nozzle. The spray gun is easily accessible and can be placed in the machine along with the spray nozzle to clean the gap.

For our flow of 3 meters high, 4 sections were enough.

The movable platform for fixing the laser level has a 5/8 thread. Many devices have such threads or adapters from ¼ to 5/8.

However, before purchasing a barbell, make sure that your plane builder model is suitable for the barbell. On some models with legs, these legs can be unscrewed, but even this does not help to screw the device. There are also special adapter screws on sale. There is a clamp handle to secure the platform.

The platform easily moves up and down (until it is latched) and also, thanks to the soft support heels, the device can be rotated 360 degrees. The fastening screw has a through hole through which a plumb point is projected.

Maximum weight of the device which the bar can support is 4 kg. The bar itself, by the way, is light. Its weight is only 1.5 kg (aluminum knees).

Using such a telescopic rod makes working with a laser level much easier. It makes it easy to hang the ceiling and make markings along the entire wall. Centimeter marks come in handy here. In general, a very useful accessory.

Let's try to find the pros and cons of the spacer rod.

Pros:

• length up to 3.6 meters

• compact

• light weight

• movable platform

• Fits most 5/8 threaded appliances

• The elbows are connected by metal threads

Minuses:

• not suitable for devices with ¼ thread (adapter required)

• Not suitable for all levels on legs (adapter screw required)

• plastic handle-clip (requires careful handling)

That's all. If you still have questions, write in the comments, and we will definitely answer.

A laser level is a properly designed device that is used for any construction work, helps to speed it up and complete it general markup any surface with high level accuracy. To use such a device you do not need to have any specific knowledge or professional skills. It is important to understand how to make a laser level with your own hands.

Purpose and classification of devices

The principle of operation of the device is quite simple: you need to place the laser level on the surface of the floor or wall, start it and wait until the device creates vertical or horizontal lines markings, depending on the surface used.

But such a device construction stores costs a lot, so it’s best to figure out how to create a tripod for a level with your own hands, especially since such a procedure does not require much labor.

On appearance alignment is more like a compact device that can be mounted on different surfaces. The most common mountings of the device are carried out using the following settings:

• tripod stand;
• magnetic mounts;
• bracket;
• special fastening belts.

In addition to the principle of fastening, construction devices differ from each other in the features of the projection of the laser beam onto the wall surface and its direction. Devices that used to determine direction, create a projection on the surface in the form of a point. The levels that delimit the plane include in their structure a special optics system that turns the beam into the plane itself. Today, experienced builders identify the following types of laser systems:

1. Rotary device, which can rotate around its axis, forming clear outlines. This device has a durable body, well protected from external factors. This product is often used for various construction works: from pouring the floor to creating a ceiling.
2. Positioning apparatus, which includes two radiation sources, it helps to project the plane visible to the builder. This device is most often used to furnish a room.
3. Self-leveling device- a level that includes a special pendulum that can emit about five rays. Such a device may also have a cross-type sight.

The main disadvantage of such leveling levels is their high price. The cost for a simple device is not always rational for the average user and is as much as ten times more than the cost of a simple bubble or water device.

Making a pointer with a laser

If you count all the costs for telescopic rod for a laser level, then a person will only have to spend money on purchasing a pointer. All you can create additional details yourself from scrap materials that can be found in any home. The main task When creating the device, a special pointer will be mounted in such a way that it can rotate in any direction. First, it is important to prepare the special parts of the future device:

To construct a laser cut pointer with your own hands, you need to follow some simple steps:

1. In prepared wooden block Several parallel holes are drilled on both sides. One of them is needed for attaching the pointer, and the second for guiding the construction cord.
2. After the laser device is installed in place, a rope is tied, which is needed to suspend the device above the desired structure. A hole is created at the opposite end of the block so that the cord can easily pass through it.
3. A special rope is inserted into the hole made, which is attached to the beam and tightened well.
4. In this case, any support can serve convenient shelf, including a simple shovel stuck into the ground on the site.

It is important to ensure that the installed support is fixed and securely fastened. If you neglect this rule, then you simply won’t be able to set the desired level.

Determining device quality

Using a laser level, created with your own efforts from a pointer, you can mark any room, but it is best to take into account low-light conditions so that the light beam is well defined. At the beginning of work, the device must be attached with a rope to the middle of the room in which construction work is being carried out. The level, made with your own hands, is turned in a certain direction, after which the total distance of the beam length is marked on it, then a stick is attached, on which it is very easy to mark.

After completing such procedures, the spacer plumb can be directed to any needed by the user side where the corresponding marks are made (it will self-level). Moreover, if the position of the main support is fixed, then all marks on the surface will be located at the same level. After marking the main points, they can be combined with a construction cord, along which the necessary marks can be set with a construction meter.

Creating a laser level

To design a laser level in this case, it is important to prepare in advance a container for liquid, a piece of plasticine, and also a patch, that is, a material that can easily be used to fasten the main part of the device (electronic holder). Of course, for this you will need to use a laser pointer and a piece of polystyrene foam. The device construction procedure itself will be carried out in accordance with a special plan:

1. First, take a small container and completely fill it with liquid. Most often, a large saucepan or a simple bucket is used as a reservoir.
2. A pointer is attached to the foam. It is best to use a simple nozzle that will project the point. It is important to ensure that the pointer is attached to the foam as best as possible. It is better to fasten it with a special rubber band, plasticine or a clamp.
3. The container with liquid is mounted at the required height - it will act as a stand for the laser level.
4. The laser ruler with foam plastic is placed inside the container.
5. Then the pointer turns on.
6. By changing the location of the foam in comparison with the central axis on the marked surfaces, special points are marked. All marks will be on the same level.

Despite the fact that this level cannot be called completely identical, the clarity of the markings in this case is quite high, therefore homemade designs may well be used in construction.

Formation of the cross

Another type of level that you can create yourself is a laser cress. This device is convenient to use when hanging cabinets in the kitchen or paintings indoors, as well as in many other cases. To create such construction tools You need to prepare a tripod for a video camera, a non-working player and several unnecessary disks.

Creation scheme:

1. A cross made of laser pointers is installed on a tripod so that it begins to rotate around its axis. You can also use a drive from the player for this.
2. It is also important to take into account that the level can freely move from one vertical to another to the desired height.
3. The discs are glued together and attached to the old player.
4. At the end of the work, a cross of laser pointers is attached to the disks. To install it, you need to use tape or other convenient means.

Due to the fact that the device will be in a stationary position on the tripod, it can be rotated in any direction without changing the height level. Having set all the necessary marking indicators, you can accurately set the level to any desired height in the room without regularly adjusting the device.

Main advantages of the device

Of course, there is no need to expect that a level created by yourself will perform all complex marking operations. But for use in domestic conditions, such a device is quite suitable and will even surpass in many ways its quality. water device. This device is also provided with the following functions:

• large length of emitted projection;
• minimal defect rate with comparative ease of use;
• increasing the speed of space marking.

But the main advantage of such a device will be the projection of the beam onto horizontal plane. It is with the help of this property that the builder can accurately determine the vertical and horizontal markings of both the floor and the walls and ceiling. In addition, such a device can be used for marking summer cottage, house facades or when creating a fence.

Second manufacturing method

The main part of the device is also the emitter laser beam. IN homemade device Instead of an emitter, a simple laser pointer is used. To do this you need to prepare:

• bubble building level;
• thick plywood or strong board;
• a peg with a diameter of 1.2 meters with a square cross-section or a shape of five by five centimeters and a diameter of six centimeters;
• a piece of rubber with a porous surface.

With the help of simple manipulations, the laser pointer becomes an emitter from which a point is projected into the room. For this, a simple one without additional borders is used. The hole must be sealed with thick paper and a small hole must be created in it. After this, the nozzle and pointer will create a point of small diameter on the wall used for construction.

Afterwards the laser is installed to outside building level. For this purpose, special clamps are used. It is important to place a small piece between the body and the level. This will help create automation, which is important for adjusting the overall tilt of the laser beam.

Afterwards the device is placed on a special tripod stand. To create it, you need to use a stake, one part of which is well sharpened, and the second is leveled so that a flat area appears. A piece of plywood or board is attached to the flat side with a screw. There is no need to secure it completely so that you can easily unfold the board if needed in the future.

The peg is driven into the ground; if the work is carried out indoors, then a tripod is used instead of a peg. At the same time, the stand is aligned horizontally. A special level is attached to it and the emitter is turned on.

To mark the surface of a wall using a building level, you need to mark a luminous point on the wall, and then turn the laser in the direction in which the marking will be made.

After this, a second point will appear on the wall. If you combine them, a horizontal line will appear.

Preparation of construction equipment and tools:

• before work, it is important to eliminate the place of the pointer where there is no insert with a pattern, such a hole is sealed with cardboard, in which a small hole is made, after which the cap is carefully placed in its original place;
• such procedures are important to achieve higher clarity of point projection;
• It is important to make a simple stick sharp at the end, and install plywood on top of a flat base. The angle should correspond to ninety degrees;
• A bar is installed on top of the board, the same length as the bubble level. Installation is carried out using a screw so that it can be turned in different directions. At the end, the bubble level is attached to the pointer; for this, a porous elastic band and a clamp are used; if this is important for the cut, then a special recess is created.

If you want to purchase a building level, you don’t need to quickly go to the store and purchase an expensive device. You can show interest, donate a little of your time and create a level with your own hands from scrap materials.

The convenience of the laser level was appreciated by everyone who used it. However, the cost of factory copies is quite high, even if the device was purchased from a Chinese online store. With a cost of no more than 100 rubles (for the purchase of a children's laser pointer), and devices available in the arsenal of any home handyman, you can make a homemade laser level.

The accuracy of the device will be sufficient for home construction work.

The simplest options for a homemade laser level from scrap materials

Bubble level level

To make it you will need a building level and a laser pointer. TO bubble level A pointer is attached, onto which a clip is placed to secure the button. You can use a camera tripod as a tripod for a laser level. The level is set strictly to the horizon, then the tripod is adjusted.

When rotating the building level, the air bubble should always remain in the upper position. After which you can mark the horizon from any laser point on the wall.

DIY hanging bar from a laser pointer

A block is used as a base, preferably made of heavy wood. A hole for the laser pointer is drilled at one end; this will be the lower part of the device. Top part The bar is suspended on any device. A correctly centered level, when rotated, draws a horizontal plane on the walls.

Float-based level

This is the simplest version of a laser level, made on a quick fix. Water is poured into a wide container (bowl or deep plate), almost to the brim. A piece of foam plastic with a laser pointer fixed horizontally is placed on top. When rotating the foam, the laser beam will always be at the same level.

These level indicators are suitable for simple work. For example, when building a fence or digging a pit for a swimming pool. If you are renovating an apartment, you will need a more precise tool.

How to make a laser level on a gimbal

Without increasing the design budget, you can make a fairly accurate self-leveling laser level from the same children's pointer.

For production you will need:

• two old hard drives of the same size;
• plastic or fiberboard for the box;
• block for 3 AA batteries from an old children's toy;
• soft wire from headphones;
• aluminum profile or a corner from an old cornice.