How to repair a gas burner from a spray can. Gas furnaces and burners: selection, operation and repair. Reasons to contact a specialized service center include increased fuel consumption, increased noise, repeated blocking of the device and

Customer Service. Check out 24 hours a day.

Our company repairs, adjusts, cleans and diagnoses diesel and gas burners. The following manufacturers; burnersLambordgini, Cuenod burners, Gierch burners, Roca burners, Weishaupt burners, Riello burners, Ferroli burners, Bentone burners, Ecoflam burners, Fbr burners, ACV burners, Hansa burners, CTC boilerand other manufacturers. You can get advice and call a specialist by calling us.

Gas burners are one of the main parts of fuel boilers. They are used to burn fuel directly, and their failure has a very detrimental effect on the heating process. Or rather, it disables the entire system. A timely service inspection of the device would help avoid this, but it is not available to everyone. And in this case, the repair of gas burners offered by our company will come in handy.

What can cause the failure of one of the most important parts of a fuel boiler? There may be several reasons, and the most common is irregular technical inspection. Failure to identify problems in a timely manner entails the need for repairs. diesel burners. In addition, this causes a violation of the optimal operating mode of the device, a decrease in efficiency and an increase in thermal loads.

Of course, many owners of fuel boilers would like to avoid such consequences, which means that regular technical inspections become really necessary. Without it, it will be difficult to imagine the trouble-free functioning of the main element of the fuel boiler, but with it it will no longer be inevitable urgent repairs burners

But this is far from the only reason for equipment failure, which is sometimes difficult to understand without a specialist. The cause of the breakdown may also be incorrect use of the fuel boiler, which completely crosses out all operating rules. Careless use of the device will inevitably lead to the need to replace any parts and repair gas burners.

And do not forget that contamination of fuel boiler parts can also cause an early breakdown. Again, timely service maintenance, which will include cleaning. But many people don’t take this into account and hardly know how to avoid a breakdown, hoping that it will simply bypass it. Then renovation work will be inevitable, and it is better to produce them in a company that knows what it is doing.

Burner repair by professionals

Service	Price
Visit of a specialist for diagnostics inflatable burner up to 90 kW.	1500 rub.
Cleaning the boiler with a diesel burner	from 5000 rub.
Diagnostics of automation and adjustment of one circuit	1500 rub.
Setting up a gas inflatable burner up to 90 kW. With a gas analyzer.	6000 rub.
Setting up a diesel inflatable burner up to 90 kW. With a gas analyzer.	6000 rub.
Repair of inflatable (gas, diesel) burners up to 90 kW. No spare parts for the burner.	4500 rub.
Gas setting modulating burner (Weishaupt type)	11000 rub.
Work performed at night increases

In our company you can order an employee to visit the site of the breakdown. And we will give you confidence that all work will be carried out by specialists and not by amateurs. Our masters have many years of experience, and therefore they repair diesel burners not only within an acceptable time frame, but also in such a way that you do not have to turn to professionals for help too often.

But someone might think that it would be easier to buy new equipment rather than carry out repair work. But in reality it will be more difficult and costly. To purchase this or that equipment, you need to find exactly the model you need. And such searches can take a decent amount of time. So why waste it practically in vain?..

And if a model similar to the previous one cannot be found, then someone decides to offer to buy completely different equipment. But you will need to get used to using a new fuel boiler, which will also take time. So why break the usual routine when, instead, you can repair failed gas burners through specialists?..

It will be more a good decision, which will save you a lot of time. In addition, this way you will significantly reduce your costs. Yes, since a malfunction has already been discovered, it will be easier to fix it. But replacing the entire equipment is worth it big money, and in comparison with this, repairing burners will be a very cheap pleasure.

One way or another, the work of specialists, as a result of which your fuel boiler will return to operation, will be justified. A modern equipment and labor experienced craftsmen will convince you that the problem was not as global and terrible as it initially seemed. And everything to avoid a recurrence of such a situation in the future is a timely service inspection and correct operation fuel boiler and burners. This will save you from unnecessary worries and costs. And our specialists, who carry out any work around the clock necessary work with fuel boilers will help you achieve the best and regular performance of your equipment.

Our specialists will help you select, install, configure and launch high-quality equipment that in the future will not cause a lot of hassle and problems with setup and repair. We work with boilers and burners Baxi, Vaillant, Viessman, Protherm, Buderus, DiDietrish, Ferolli, ACV, Weishaupt, Gierch, Hansa, Lamborghini, Oilon, Cuenod, Fbr, Ecoflam, etc.

A simple burner, there were quite a lot of similar reviews here. I'll try to be concise so as not to overload unnecessary information, just an attempt to complement the earlier reviews and remind you of the product in this category in general.

First with a failed burner. The other has a burner.

I received some kind of unsuccessful burner, noticeably crooked. Perhaps they were bent during shipment, by the way, minus the purchase of the burner in China, the “trunk” is easy to bend, at the attachment point it is very fragile, it would be better to send it disassembled. Maybe it’s worth writing to the sellers about this? Perhaps this was a defective burner from the beginning, since the “trunk” did not bend back in any way, it turned out to be a Z-shaped something that returned to its original position.

The burner worked unstably, there seemed to be a flame, but it didn’t really heat anything. Since this was the first burner, it seemed that it was normal, it was burning and it seemed to work. Such an overgrown lighter.

The valve had no travel limitation! If you confuse the direction of rotation of the gas supply valve and open it further, from open state, it fell out, gas came out of all the cracks (including back), creating a fire hazard. In such a situation, I once threw the burner into a snowdrift. Another time I tore the flaming burner off the cylinder (fortunately it didn’t have time to heat up, but the sluggish yellow flame not scalding if you do everything quickly), then the valve in the cylinder with the burner removed automatically shut off the gas supply. Extra heroism, on the other hand, a torch is a dangerous tool, you need to remember this.

I tried to “repair” the burner, drill out the nozzle (I thought the gas flow would increase), but it got even worse. The flame turned yellow, like from a lighter. Next, I tried to cover the air inlet holes with foil, also without much success, the burner operating mode changed, but it didn’t get any better. By by and large lay idle. It would be better to buy it in a regular one hardware store, this was one of the worst purchases.

A little later on mysku I saw a review of a more successful burner and that it can melt aluminum:

Yes, and there were many reviews of burners, the essence is approximately the same for all, they burn, burn, melt in the same way, nothing new can be invented here, in addition to what was previously published:

I was thinking about buying the same one. Somewhere in the comments there was a link to a normal burner from the cheapest ones. I just need one for occasional short-term work.

I bought it, unpacked it, weighed it, everything as always:

Additional Information

There are also scales in the photo:

Additional Information

Accordingly, the wife took into her many instruments. These instruments have everything that is presented in , in the “neighboring” one, and much more, thermometers, pyrometers, a food printer, etc. When I film the use of the burner in our case, I will update the review.

Examples of application in cooking from other sources, this is a different application technique, but the essence is the same, local heating.

Gas burner for caramelization:

10 reasons to use a cooking torch:

In culinary stores, prices are naturally slightly higher. You can look and, but naturally don’t buy.

It was also useful in practice for thawing the lock on the gate. Without a torch I did it with a hair dryer; with a torch, the lock had already thawed while I was still unwinding the wires for a hair dryer.

In the end, I can say that it is very useful, universal tool. And this particular burner seems attractive in terms of price/quality ratio. On the other hand, it may be easier to buy this type of product at any hardware or construction store; you will still have to buy gas there. The prices are comparable, especially considering the speed and convenience of purchasing in a regular store, and the ability to quickly replace a defective burner under warranty.

I'm planning to buy +19 Add to favorites I liked the review +27 +50

Repair gas stove DIY is prohibited by Russian law. True, criminal liability is not yet provided for; if an accident occurs, troubles are expected. In the hero city of Volgograd, one smart guy started a vent water heater combustion products. 4 people died. The authorities classified the case based on the article causing death by negligence. Gas service technicians have the right to replace equipment and perform service work. This is relevant, starting with connections and ending with switching to a different type of fuel. Below are a couple of recommendations, not a user manual, just general techniques.

Installation of a gas stove with electric ignition

Darina, Hansa, Ardo – so different and at the same time the same. The repair of gas stoves by Hephaestus is exactly like the repair of Ariston; gas stoves are made up of standard units. It is enough to look at a single device to understand the circuit. Have a reference book to help you properly maintain gas pressure. When set correctly, the flame is even and blue. Orange flashes indicate an imbalance in the fuel mixture. If the settings are incorrect, the flame will fail (especially typical for carob ovens).

Those who have read the reviews of the VashTekhnik portal regarding gas instantaneous water heaters, do-it-yourself repair gas stoves will seem like child's play! You cannot do it yourself, but you can clean the device. The technician will have to clean candles, combustion sensors, burners, and sometimes nozzles. There are a lot of interesting things inside the gas stove. To the master proper cleaning equipment, you should understand what you will see inside. Under the gas stove table:

Burners. They are often bolted to the gas stove table. Each burner consists of a lid, a divider, and an injector (nozzle). They are not rigidly attached under the table; each one is fitted with a steel or copper tube, fastening is carried out like an American one. You will need a key of approximately 13 to remove the products. It is more convenient to clean if something is clogged inside. Beware of tearing off the head or thread - you will have to replace it. After assembly, check the tightness by washing. The procedure involves applying foam to the disputed nodes.
There are two candles around the perimeter of the burner. One serves as ignition (due to a piezoelectric element or an electronic circuit), the second is a thermocouple, included in the combustion control circuit. It's quite easy to distinguish. The high-voltage spark plug is covered with a ceramic caftan so that the spark does not strike below a predetermined level. When the arc flows, you can see: the tongue of the discharge licks the body of the burner. Gas stoves with electric ignition will be properly grounded by a technician. Beware of using plumbing connections or connectors pierced with metal threads. During installation, the hoses are separated from the riser by special gaskets. Failure to follow the rule will easily provoke an explosion in favorable situations. We wrote in more detail, we remind you again. The candle with a thermocouple is covered with a bronze caftan that conducts heat. The faster the semiconductors cool down, the flame goes out, and the protection that cuts off the gas supply will work more reliably.

Most often there is a collector under the table. A thick tube from which a line goes to any burner. The gas flow is controlled by solenoid valves. The number is usually equal to the number of burners. When the burner flame goes out, the rest will burn. The expediency of the decision can be challenged, but this is how it is done. Each solenoid valve contains an inductor. The thermocouple heats up, an EMF (tens of millivolts) appears, keeping the devices open. Full order turning on: turn the gas supply regulator, press. We press the piezo ignition button, or the electronic circuit performs a set of procedures independently. We hold the handle for a fixed time. The thermocouple warms up, an EMF begins to be generated, the electromagnetic valve is held open due to the phenomenon discovered by Seebeck. As soon as the gas goes out, the sensor plug cools down and the gas supply stops. The process is inertial, we believe that the day is not far off, flame ionization sensors will begin to be used in gas stoves, allowing the protection to operate instantly.
Similar to the gas manifold, there is a distribution valve panel inside. Single high-voltage wires run to each ignition electrode. Another way to distinguish a thermocouple: two wires with a thinner cross-section stretch to the sensor. The spark breakdown goes to the housing, the second ignition wire is superfluous. If the gas stove is deprived of grounding, we have a chance of getting an electric shock. Fatalities are possible - an additional reason to entrust the installation to a professional. The collector is connected via connectors. There is protection against incorrect orientation of the plug; you can easily mix up some places. When you open the burner, a spark will jump on another divider. It’s not very pleasant, a flash of flame is possible.

If a charge is formed electronic circuit, you will find inside a simple thyristor, diode, capacitor, fuses. The circuit operates, powered by a capacitor charge with a subsequent burst of energy from the spark gap of the spark plug. Repair of electric ignition of a gas stove concerns the listed elements. The fault is easy to notice. Burnt elements are black or similar in color.

Setting up a gas stove for a different type of gas

Gas is endowed with two significant characteristics:

The calorific value is determined by the composition. The higher the methane content, the lower the parameter. For natural gas, the calorific value is predetermined by the location where the natural resource is extracted.
The pressure depends on the type of gas. Liquid requires higher. For the main line, the typical value is 13 mbar. The parameter ensures the correct operation of solenoid valves, injectors, and burners.

When too high blood pressure the gas burns incompletely, soot and orange flames will appear. The system may not operate correctly. I have come across instructions recommending the use of a reducer to obtain 13 mbar from a balloon. There are probably restrictions. It is not without reason that it is recommended to place two cylinders in parallel. Please note that the main gas is actually liquid, supplied through a reducer. It is pumped from tanks into containers from which houses are supplied. Find out the wiring diagram for the house where you live. Occurs natural gas, distributed centrally, having lower cost, pressure, and calorific value. The pressure is assumed to be 13 mbar. This aspect must be taken into account when installing and repairing a gas stove.

The reason to call professionals for installation and configuration is that the specialists know the parameters. Of course, a person with a certificate is also aware of local conditions. Now imagine what will happen if you unknowingly connect the equipment incorrectly! It's a gas, stop joking. This is especially true in the outback, where neighboring houses may have different connection. It is recommended to purchase a set of replacement injectors for different gas pressures. They described the process of boring jets with their own hands and mentioned that the law prohibits rework. The work is unsafe. Before purchasing, ask your gas service for the parameters and ask the store if the equipment is suitable. It’s not too late to start making inquiries during the next cleaning. It's not a fact that everything was done correctly.

How to adjust jets. The size of the central hole changes. Less pressure, the hole becomes larger. Verticality and alignment must be maintained, otherwise gas will leak to the side, which will lead to an accident. It is appropriate to recall that in old Soviet gas stoves the jets are hidden deep inside. The design of the burners is unusual. Between the nozzle and the divider there is a tube with a pair of ears attached to the frame. There is one frame for every two burners. In pairs, the pipes are attached with ears inside the housing. A bowl with a nozzle is placed at the lower end, and a divider is inserted into the upper end. The gas stove operates using a jet stream. Propane-butane is heavier than air.

The peculiarity is that opposite the nozzle there is a tube with a radial cutout. Needed to unscrew the hex nozzle without using a long socket wrench. In modern gas stoves, the jet is located under the flame. A different arrangement improves traction and discourages ordinary people from climbing inside the stove. Repairing a gas stove with your own hands is a dangerous business.

Electric stoves today also look like a more appropriate option for summer residents.

Our service center provides 24/7 burner repair, boilers and boiler equipment in Moscow and the Moscow region.

Certified engineers of our company carry out quality repairs diesel burners and gas burners of any complexity in the shortest possible time.

In order to identify a defect, a service engineer diagnoses the equipment, after which he reports the cause of the malfunction and a work plan to eliminate it.

Cost of on-site and diagnostics for burner repair

Service	Daily rate, rub	Weekend tariff, rub
Departure of a service engineer within a small concrete ring	1200	1400
Travel outside the Small Concrete Ring (per kilometer)	35 rub/km	40 rub/km
Carrying out diagnostics (identifying the causes of the malfunction)	1000	1000
Other works

The day rate is valid from 8:00 to 19:00 from Monday to Friday. Weekend rate is valid on weekends and official days holidays. At increased load service center at night and evening time an additional increasing factor may be introduced for work. The size of the coefficient is specified by the operator when placing an application.

Guarantees

The company is responsible for the quality of the services provided, and gives a 6 month guarantee for the complex of work performed.

By contacting us, you acquire qualified assistants in the repair and maintenance of boiler equipment, gain peace of mind and confidence in safe operation engineering systems your country house.

Low prices for work and spare parts;
Promptness of departure and execution of the application;
Service specialists have more than 5 years of experience;
Spare parts are always available in stock;
Service engineers are trained in authorized centers of manufacturers.

Our certificates

VIESSMANN Certificate

How we are working:

We accept your call;
A service engineer arrives;
The service engineer repairs the burner;
Cleaning the workplace;
Issuing recommendations;
Warranty service.

Inflatable boilers and burners

If we divide boilers according to their complexity, the variety of devices they contain, the complexity of diagnosing faults and repairing them, then the least problematic boilers are floor-mounted atmospheric boilers, then wall-mounted, and the most complex are floor-mounted inflatable ones.

Inflatable floor standing boilers consist of two main parts:

- boiler body;

- inflatable burner.

The body of the boiler is, roughly speaking, a cylindrical container into which a flame of combustible fuel is inflated with a burner. The boiler has simple sensors and regulators for the automation system. The boiler body is also a heat exchanger, through which the thermal energy of fuel combustion (gas, diesel, fuel oil) is converted into thermal energy coolant that circulates in its (boiler) walls.

However, the heart of an inflatable boiler is the inflatable burner.

— The burner contains basic automation elements, sensors, and a control unit for the entire boiler.

— The main operating modes of the boiler are configured and regulated in the burner.

— The fuel-air mixture and environmental parameters of fuel combustion are adjusted and prepared in the burner.

— The burner generates diagnostic signals for faults, errors and malfunctions of the boiler.

Repair, adjustment and tuning work is the most expensive and time-consuming - on an inflatable boiler. The most expensive spare parts are for the inflatable burner.

Therefore, all recommendations for the operation of boilers (link to articles on the operation of boilers) for an inflatable boiler are especially important. Compliance with them affects the serviceable, durable and safe work burners and boiler bodies, affects fuel consumption.

Photo gallery of our works

Gas burner TORCH WS-502- professional portable
gas burner which is used as a source of directional
flame with a torch structure, in which the flame temperature in the zone
the main flame reaches 1300°C.

Professional portable gas burner with piezo ignition for
standard propane-butane cylinder 220 g. (0.5 l). Length 150 mm.
Nozzle diameter 18 mm. Fuel consumption 120 g/hour. Power 1.65 kW

It was purchased from the Gearbest.com store with a 5% discount
ye. Arrived in Ukraine in just 6 days and delivered directly into your hands by courier.
The product was ordered on September 20, on the 22nd of September it was sent and already
On the 28th the parcel was received by Nova Poshta courier. Pleasantly surprised
To be honest, the delivery speed of this store.

A gas cylinder was purchased at a hardware store for 1.5 euros.

It was packed in a blister on a cardboard and a standard white bag.

Main characteristics:

Flame temperature approximately 1300-1450°C

Automatic piezo ignition

Energy carrier – gas cylinder chik 220 g

Adjusting the flame intensity

Ergonomic design

A portable gas burner is used for a wide variety of jobs:

For soldering and welding low-melting metals and alloys (lead, tin, zinc, copper, aluminum, gold, silver, etc.);

Melting and welding of glass and plastic products, including plastic pipes, synthetic cords and cables.

For heating various objects, for example, to facilitate the loosening of “seized” threaded connections;

For defrosting locks.

To remove old paint;

To start a fire (fireplace, bonfire, grill, barbecue);

For singeing carcasses poultry, as well as game for hunting;

For defrosting food (meat, fish);

In farming and gardening;

Widely used in workshops, for various works in garages, laboratories;

When sewing clothes;

For architectural decoration.

Connection to the can:

Turn the orange button clockwise. Connect the gas
burner to gas canister and press. Then, to secure
spray can, turn gas burner approximately 25° clockwise.

Ignition:

Hold the gas cylinder straight. Turn the orange button to? ? ?
turn counterclockwise and press the button to ignite.
The intensity of the flame can be adjusted.