Decorating walls with ordinary paper, even if it is very durable, is not in fashion today; it is much more interesting to figure out how to stick it correctly vinyl wallpapers, decorate the room with them, creating your own unique design.

What do you need to know before gluing vinyl wallpaper?

If you decide to abandon stereotypes in decoration living rooms, first take a broader look at available materials. Today, paper looks almost primitive, but you shouldn’t go to the opposite extreme either - and cork is quite expensive. Non-woven fabric is quite affordable, but requires very careful handling and, without experience, it is better not to mess with it. It remains to be seen how to properly hang vinyl wallpaper; perhaps this will be the most optimal solution both in terms of price and ease of finishing.

So, the choice is made. Now let's take a closer look at the material that was given preference. Essentially, this is the thinnest layer of PVC, or, in other words, polyvinyl chloride, which is quite common flexible plastic. The most common types of wallpaper made from it are smooth and foam. The first are divided into compact vinyl and silk-screen (with the addition of silk threads). The latter, obtained by heat treatment, are divided into varieties such as heavy, high density and chemically embossed.

The advantage of vinyl is that it can be washed, and special impregnations prevent the occurrence of fungi. In addition, the foam or textured surface of the material allows you to hide minor irregularities on the wall or ceiling. The disadvantage of such wallpaper is that it does not allow air to pass through at all. In other words, if the house is built from “breathable” materials, vinyl trim will turn the premises into a thermos. During the gluing process, the paper base can stretch, which can cause distortions if the material is handled improperly.

The site’s site masters have prepared a special calculator for you. You can easily calculate required amount wallpaper

We glue vinyl wallpaper with our own hands - step-by-step instructions

The first and basic rule that you need to follow when decorating a room is that you should never glue vinyl wallpaper onto uneven walls, the only exception may be small chips. Yes, the material in question is capable of smoothing out minor curvatures of the plane of the walls, but the key word here is “minor.” And protrusions, even the most inconspicuous ones, are unacceptable. Therefore, as carefully as possible, using plaster and putty. If you have to finish a material with a high degree of moisture absorption, it must first be treated with a primer. Only then do we glue the vinyl wallpaper with our own hands.

The room whose walls are to be covered with wallpaper should not be cold or damp; in addition, you need to turn off the air conditioning and make sure there are no drafts.

You can weld the glue yourself; it can be a paste or any other option available to you with the addition of PVA. However, a homemade composition is not always good, especially if you need to cover a wall with it. The fact is that on dark concrete or on primed cement plaster It will be difficult to see where the glue has already been applied and where it is not yet applied. And uncoated areas will definitely result in problems when covering walls with wallpaper. Therefore, it is better to take special mixtures that, thanks to certain additives, when applied to any surface, paint it lightly. pink color, becoming transparent after drying.

Technology for gluing vinyl wallpaper step by step

Before you start work, take a plumb line and a pencil, and check how vertical the line of the angle is, from which it is best to start gluing the walls. Choose an arbitrary angle, preferably the one closest to the door; if it is not vertical, apply a plumb line to the door itself top point and beat off the line with coated thread. Next, we will consider in detail the technology of gluing vinyl wallpaper.

How to properly hang vinyl wallpaper - step by step diagram

Step 1: Wallpaper Marking

On a well-washed and dried floor, unwind the roll face down. We take a tape measure and measure the required length, having previously found out the height of the wall from the ceiling to the baseboard (taking into account the ceiling border). We make marks with a pencil along both edges of the roll and connect them with a cutting line, along which we separate the measured piece of panel with scissors. In the same way, we divide the remaining roll into equal parts, combining it with the previous canvases so that the pattern at the joints matches.

Step 2: Surface Preparation

The previously drawn vertical line from which we need to glue the wallpaper can easily become smeared when applying glue, so we draw along it with a pencil. Next we have 2 ways. If the vinyl layer is applied to a paper base, use a roller to cover a strip of wallpaper with glue, then fold its ends towards the middle and leave it to swell for a precisely measured time, usually indicated on the roll.

In just these few minutes you can just have time to prime the wall with the adhesive mass. If the base is non-woven, the glue is mostly applied with a roller to the wall, and the panel is covered with it only around the perimeter.

Step 3: Getting Started

The most difficult stage begins - gluing vinyl wallpaper with your own hands. We take the first page for top corners(if they have a paper base, then very carefully, without stretching) and apply along the previously marked line. You can glue it either from the ceiling or with a small indentation, following it along the entire perimeter of the room. Inserting a piece of wallpaper into a plaster molding requires special skill.

We smooth the panel from top to bottom, pressing it against the wall with successive movements. This is best done using a wide foam roller, just be sure to take a clean one, do not confuse it with the one you used to apply the glue.

Step 4: Complete wall finishing

Before gluing the joints of vinyl wallpaper, apply the strips to the wall, following the pattern. Remember, the material you are working with is quite dense and overlapping always looks extremely unsightly. In places where wires exit the walls (switches, sockets), we make small holes before the panel completely covers this area, and bring the wiring to outside cutting

Then we continue smoothing. If the ceiling has a slope, for example attic room, we apply the strip end-to-end to the previous one, holding the next cut at the corner closest to the seam, and leaving the second one hanging freely. Then, pressing the panel along the upper edge of the wall, we cut off the excess piece with a sharp stationery knife.

During the smoothing process, make sure that no air remains under the wallpaper; you also need to try not to stretch the canvas, as otherwise wrinkles will appear. We also carefully push the excess glue to the edges and then remove it with a clean rag. If air bubbles do form, carefully pierce them with a needle and press the wallpaper in this place, smoothing it with a roller. When we reach a corner, we try to ensure that the strip extends to the next wall with an edge no wider than 5 centimeters, especially if the corners are uneven. At the end of the work, carefully trim the not yet dry canvas along the baseboard and make the holes wider in the locations of switches and sockets. We dry the wallpaper without air conditioning or drafts, without opening the window and closing the door tightly.

Vinyl wallpaper is ideal for both new buildings and for finishing when renovating premises. You will learn how to glue vinyl wallpaper from our article.

Tools and materials

To work you will need:

• A special brush or fur roller for priming walls and applying glue.
• Rubber roller for working with seams.
• Yardstick.
• Level or plumb line.
• Paper tape.
• Cotton rags (to remove excess glue).
• Scissors, knife for cutting cloth.

Subtleties of the process

How to stick vinyl wallpaper: sequence of work

1. Preparing the walls

• The walls must be well dried before gluing, especially if plastering work has been done before.
• The surface must be free of visible differences, potholes, and chips.
• The walls are primed with diluted glue or primer deep penetration. It is recommended to pre-treat the walls with an antifungal compound (anti-fungal primer or any fungicidal compound).
• The glue is diluted warm water according to the instructions on the package.
• A vertical line is drawn using a level or plumb line, which will serve as a guide for gluing the first sheet.
• Then you need to turn off the power to the room and remove sockets and switches from the walls.

Your attention! The walls are cleared of old decoration, the cracks are puttied and the surface is leveled. How to check if the walls are well dried? Glue a small piece of plastic film; if water droplets appear on it overnight, the wall needs to be dried better.

You can also check the wall for the degree of preparation by gluing a piece to it regular tape. Abruptly removing it and viewing reverse side, it will be clear how the wall is prepared.

Wallpapering

The presence of paint or plaster residues on it indicates poor preparation surface or any other room.

Before gluing vinyl wallpaper, you need to make sure that there are no drafts in the room; under no circumstances should you turn on fans and air conditioners, or open windows until the canvases have completely dried.

You cannot stick the canvases onto old ones; they must be removed by first moistening them with water. A similar procedure is followed.

2. Preparation

The rolls are cut into strips, leaving an allowance along the length of 10 cm. If the coating has a pattern and you need to select it, when cutting the strips you need to match the pattern, not forgetting to leave an allowance.

3. Apply glue

After the wall is leveled and dried, and the glue is prepared for application (it should sit for 10 minutes after stirring), you can begin gluing the canvases.

Vinyl sheets are glued end-to-end, without the sheets overlapping each other. Glue is applied to the size of the first sheet, stick it on and proceed to preparing the next section.

When gluing, make sure that no adhesive residue gets on the front side canvases, especially when working with light shades.

Your attention! When gluing non-woven vinyl coverings, you do not need to apply glue to the sheet.

Before starting work, read the instructions on the package, and just that.

4. Trimming the edges

After gluing, an allowance remains near the baseboard at the bottom and top, which must be trimmed with a sharp blade.

Advice! It is better to trim the coating when it is well dry, otherwise you will not be able to make an even, neat cut. The knife blade needs to be changed periodically.

Classic technology

It is better to glue vinyl covering in a duet. One at the bottom cuts the canvases and applies glue to them, the other, on the stepladder, glues the strip and first applies the glue to the wall.

The panels are pressed to the base of the wall and the bubbles are pushed out with a roller from the center to the edges and from top to bottom.

If, during gluing, glue residues appear on the edges, you should immediately wipe them with a soft cloth or sponge.

Sticker near the baseboard

If it is not possible to remove the plinth, the sheets are carefully cut at its upper edge.

Work at the top

To prevent glue from getting onto the painted ceiling during work, you need to wrap the panel 5 cm at the top. After gluing the strips, finish this area by applying glue with a small narrow brush.

Corner finishing

Corner finishing options:

• You can glue the canvases overlapping in the corners. This method is applicable for plain canvases and items with small patterns. When gluing, the sheet is overlapped onto the adjacent wall by 1 cm, and this overlap is subsequently covered by the adjacent sheet. This sheet is also pasted along a strictly vertical strip.

For gluing overlapping panels, special glue is used. The disadvantage of this method is the unaesthetic appearance of the corner.

• Another way is to begin the work in the same way as the first method, but with a larger (2-3 cm) allowance. After the canvases have dried, two sheets are cut vertically at once using a stationery knife.

For this purpose, use a spatula or a metal ruler, along which two layers of sheets are cut from bottom to top. The cut parts are removed, the edges of the canvas are folded back, glue is applied and rolled with a roller or plastic spatula. The seam in this case turns out perfectly smooth.

Trim near batteries, switches and sockets

Advice! Behind the heating radiators, the wallpaper is extended 15-20 cm and pressed against the wall with a narrow roller. You can not stick the canvas behind the batteries, but paint the wall to match.

In places where sockets and switches will be located, the gluing process follows the usual pattern. There is no need to cut holes in the sheet in advance, since they may not coincide with the technological holes for electrical points. This is done after gluing the panels.

Vinyl wallpaper on paper basis

The principle of operation differs little from usual, with the exception of a few points.

Vinyl wallpaper on paper based Many people know how to glue, since they have been traditional for a long time.

Glue is applied to the surface of walls and panels. On the sheets, the glue must saturate the base; for this, the panels are folded with their front sides facing each other and left for some time.

Heavy vinyl wallpaper

This type of gluing is somewhat more difficult than paper-based materials. It will not be easy to master this work on your own, especially if you have no experience in this matter.

Before gluing heavy vinyl wallpaper, purchase special glue. We recommend using Quelyd, KLEO Line Optima or Metylan Interlining.

This finish stretches when wet and contracts when dry, which affects the quality of the seam.

The glued sheets should not dry out too quickly, so the room temperature should not exceed 15 °C.

Summing up

We hope our article was useful to you. In order to more accurately understand the technological and practical issue, our website provides detailed photo and video instructions in which you will find useful information on this issue.

Photo gallery

One day, for every family, the time comes overhaul one, several rooms or the entire apartment. Let's talk in detail about the technology of gluing vinyl wallpaper to the walls of rooms. Will be announced practical advice who will help you make repairs yourself or with an assistant.

Before dealing with the best option gluing wallpaper, consider their types. There are two main types of materials:

1. paper-backed vinyl wallpaper,
2. vinyl wallpaper on non-woven backing.

Both varieties are double-sided. One side is paper or non-woven, with which the material is glued to the wall. The second is polyvinyl chloride, thanks to which the room will look elegant after renovation. These materials have been known for a long time, since the 50s of the twentieth century. Pasting is done according to special technology using special adhesive mixtures.

To work productively, you need to prepare all the necessary tools in advance.

Preparing the surface

Prepare thoroughly before gluing work surface(wall). We prepare as if we wanted to glue ordinary materials.

Important!
Do not use putty that has PVA glue as a base. Vinyl wallpaper will not tolerate this.

The second caveat is that manufacturers recommend additionally carefully and thoroughly priming the wall before gluing it. This applies more to heavy, thick wallpaper. To glue the light ones, you need to remove all the cracks from the walls, level out bulges and other irregularities. To do this, apply the putty to the surface to be prepared in compliance with all technologies. It must not be allowed to sag immediately after drying or after some time.

We glue vinyl wallpaper

The technology is such that they are first cut into the required strip size. The entire length allowance is 10 cm on both sides. If you purchased canvases with a pattern, then try to select the second adjacent strip so that both align as much as possible.

Before cutting, be sure to look at the series on each roll. If it matches, great, you can start preparing. If you find a roll with a different series, open it and see if the fabric is the same shade? If yes, you can use it in surface design; if not, then set it aside. It may come in handy many years later, if a pet damages the area, spare wallpaper can be used to patch up the damaged piece of covering.

Pasting technology

It is necessary to glue vinyl wallpaper end-to-end. There is a nuance with this method: when our wallpaper dries, it may suddenly “shrink,” and noticeable gaps will appear in the form of tracks. Therefore, for material having vinyl base, a little less glue is applied than on paper.

Do not pull them wide when you glue them. Press the material against the wall with a special, convenient roller with rubber surface or a brush with short bristles. Do not use a spatula. Pinned? Carefully and gently run the tool along the seams.

Wallpapers with vinyl covering must be glued exactly end-to-end

Since these wallpapers are capricious when hung, they, like others, are glued when closed windows and windows so as not to accidentally create drafts. The material cannot stand when the air temperature drops or rises sharply, or when the humidity changes. Therefore, remember that ventilation will have to be postponed and you should not even turn on the air conditioner.

Be careful that the adhesive mass does not accidentally get on the front side of our canvas, otherwise it will ruin it. Especially if you don’t notice and remove it in time.

Dilute vinyl wallpaper glue with water. How? This is written in detail on any package. Wait until the mass swells, according to the instructions - this is approximately 5 to 10 minutes.

There are two main ways to apply adhesive:

• Apply glue only to the surface of the wall to attach vinyl wallpaper to non-woven fabric or paper,
• We coat both the wall and the canvas with adhesive.

Which option is needed in your case? Read the roll packaging carefully. To put it simply, if the base is on paper, we apply the composition to the wallpaper (you can also apply it to the wall), and if it’s on non-woven fabric, only to the wall.

We try to glue vinyl wallpaper correctly. They are not immediately pressed against the wall after application. adhesive composition. First, carefully fold the wallpaper so that the base is against the base, and wait until the glue saturates the canvas. More thin material It will be ready faster, but with a dense one you will have to wait a little longer.

If you want the material to look neat on the wall, apply the glue evenly over the entire canvas and in a fairly thick layer, but at the same time, observing the measure. If everything is done correctly, the seams should remain as clean as possible after gluing.

How to glue corners with vinyl wallpaper? It is wrong to combine the canvases in the corner - exactly where the walls meet. An overlap of 2 to 3 cm is required on one of the walls in the direction of work.

In the corners of the strip you need to glue them slightly overlapping

Assistant for pasting vinyl wallpaper

It is convenient to glue vinyl material with an assistant. One person climbs up the ladder with the canvas and presses the wallpaper to the surface of the wall. The second remains below and supports the lower part. At the same time, he carefully aligns the entire strip strictly vertically. To make it easier, many take care in advance and draw a vertical line.

After leveling, the wallpaper is easily pressed, displacing the air bubbles formed between the wallpaper and the wall. To do this, use a brush - it’s faster and better than using your hands. The brush is carried out from top to bottom, then from the center to the edges. If you notice excess glue around the edges, immediately wipe it with a clean towel, cloth napkin, or rag. The main thing is to do this carefully, carefully, so that the composition does not accidentally get on the front part.

Removing excess

We cut off the excess edges remaining after gluing under the ceiling and at the baseboards using a sharp knife. If the tool is dull, do not be lazy - sharpen it, otherwise the blade will wrinkle and tear the edges unevenly. Only 0.5 cm of material goes under the edge of the plinth. It is best to remove the baseboards before carrying out the work and then nail them down.

As for switches with sockets, turn them off before work and remove them. The wallpaper is pasted directly onto the holes, and when dry, it is cut along the contour of the sockets and old or new sockets and switches are installed there.

After pasting, excess paper above the socket sockets is cut off

Docking over openings

No matter how hard you try, the last line will be smaller standard size roll. Experienced people try to make sure that these areas fall on window hole or turned out above the door. But for beginners this may not work. How to be?

The solution is simple. If the canvas is approximately 5 to 7 cm wider than the unglued area, then glue it end-to-end on one side and overlap it on the adjacent strip on the other. Moreover, we try to make sure that the “extra” part of the strip does not stick, but remains slightly bent. As always, carefully expel the air and glue from under the canvas. Now take a very sharp knife to stationery and cut off an extra piece for the ruler. Do not press too hard, you may accidentally cut through the putty, but our task is only to remove the excess piece. Now, as always, make sure that the edges match tightly.

From everything written above, several conclusions can be drawn. Gluing vinyl wallpaper is not scary or difficult. The main thing is attentiveness, accuracy, properly prepared wall and well-chosen glue.

Now is the time to change the decor in your apartment or create comfort in a new home.

Have you chosen vinyl wallpaper for wall decoration, but don’t know how to hang it?

Then it’s time to figure out what tools are needed for this and how to do it correctly at home.

What you need to know when choosing vinyl wallpaper

Before you start gluing, you need to decide what kind of wallpaper you want to hang in a particular room, since there are several types and varieties.

• For some, non-woven fabric serves as the basis, for others - paper.
• Vinyl wallpapers are also divided into subtypes based on production technology:

foam, flat, silkscreen, polyfoam and rigid vinyl, or as they are called washable.

As for their safety in the house where we live - think for yourself, the material from which they are made is PVC, these are the same plastic windows, linoleum, suspended ceilings.

I would not recommend gluing them in children's rooms, and carefully choosing a manufacturer that guarantees quality and environmental friendliness.

To know how to glue vinyl wallpaper with your own hands, you will have to collect a small set of tools (they are not specific and can be found in any household) and acquire some skills, which I will describe in detail in this article.

Tools for work

So, let's start with the tool that we will need in the process of wallpapering.

1. Large roller for removing air bubbles and excess glue.
2. Small roller for seams.
3. The brush is large and small.
4. Wallpaper knife.
5. Plumb.
6. Pencil.
7. Roulette.
8. Scissors.
9. Rags.
10. Putty knife.

When everything you need has been collected, we begin preparatory work.

How to prepare walls for proper vinyl wallpapering

The first thing to do is remove old paint and the pieces are not removed wallpaper and peeling putty. After this, we prime the walls and fill the cracks with putty.

When everything is dry, prime the walls with a primer, or wallpaper glue, in the proportion that you will find on the glue box. Typically the ratio is 1:8 (glue:water). A primed wall will absorb less glue and the wallpaper will adhere more firmly.

Preparing materials for work

First of all, prepare the glue according to the manufacturer's instructions.

We take into account that no matter what glue you use, no matter how you prepare it, you will need 45 grams of ready-made solution for 1 m² of vinyl wallpaper.

Pasting vinyl wallpaper

How could it be without special effort glue wallpaper, namely vinyl?

Firstly, there are several types of vinyl wallpaper, and the choice of adhesive and method of its application depend on their type, and the manufacturer usually indicates this information on the wallpaper packaging in the form of icons.

• There are wallpapers that are glued dry, these are vinyl wallpapers with a non-woven backing, in this case the glue is applied only to the wall.
• In another case, the wallpaper is on a paper base, then the glue is applied to the wall and to the panel, which, with the glue applied, is folded with the edges towards the middle for better glue impregnation.

Step-by-step instructions for wallpapering

Before gluing, make sure there are no drafts in the room until completely dry wallpaper, otherwise they will decorate your floor until the morning!

1. Before starting pasting, on the wall, using a plumb line and a ruler, we mark a line along which we will align the edge of the first panel. This is best done together, since only a specialist with extensive experience can independently create a straight line.
2. Next, we take a piece of vinyl wallpaper and apply it to the wall under the ceiling, bending the upper edge of the piece by 5-10 cm, and align the side edge along the drawn line.
3. We smooth a section of wallpaper from the ceiling to the floor, and to the sides from the center with a rubber roller, carefully removing air. Try not to stretch the wallpaper, as it will shrink back when dry and create a gap at the joints.
4. When gluing the next panel of vinyl wallpaper, try to join the edges of the panels as much as possible and carefully roll the joints of the seams with a rubber roller, after removing excess glue with a dry rag.

Pasting the corner

When we reach the corner, measure the distance from the edge of the glued wallpaper to the corner and add an overlap of 2 cm, cut off such a strip from the whole panel. We glue this strip with an overlap at the corner.

We glue the next panel overlapping into the very corner. Next we glue strips of vinyl wallpaper along old scheme- butt.

Secrets of professional vinyl wallpaper gluing

If you remember, when preparing the wallpaper panels, we made overlaps under the ceiling and on the floor. Be sure to trim these overlaps using a putty knife and a utility knife near the ceiling and floor.

We change the blade of the knife according to the degree of its dullness - do not skimp on this, otherwise the knife will simply tear the wallpaper.

Before gluing, switches and sockets must be removed, the electricity must be turned off to avoid electric shock, and the wallpaper must be glued on top of them. We cut out the holes for them when the wallpaper is dry and then we install everything in place.

In principle, this is probably all you need to know in order to cover a room with vinyl wallpaper correctly.

Good luck to everyone in this simple matter!

When thinking about how to glue embossed vinyl wallpaper, you need to take into account that they are divided into heavy canvases and light ones. The existing difference between them is quite noticeable. The reason for the drop in demand for vinyl was the poor water vapor permeability of sheets made from this material. This primarily affects the indoor climate. Environment takes in every second of evaporation not only from the human body, but also through the air he exhales, and if the wall covering does not allow the water vapor accumulating in the air to pass through, dampness accumulates in the room on all the walls. Considering that the vestibule installed windows made of PVC is deaf, like interior doors, this leads to mold growth.

Gluing heavy vinyl sheets is much easier than thin ones, which require more careful preparation wall surface. Therefore, usually the walls need to be puttied, sanded and primed, making them perfectly smooth. No protrusions should be noticeable. If inclusions remain under the glued canvases, then this will not spoil the appearance of the interior as much as on thin wallpaper, which spoil the effect more.

Heavy type embossed vinyl wallpaper is not too critical to the level of quality of preparation of the base surface.

They should also not be applied to plaster, but sanding the putty layer can also be done less thoroughly than for light wallpaper. When covering walls with heavy vinyl wallpaper, the appearance of small indentations or scratches is not as bad as the presence of any convex parts or sand.

What kind of glue will you need?

Heavy vinyl wallpaper is best glued with regular glue that includes starch. The presence of antifungal additives allows you to protect the surface of the walls from the appearance of fungus and mold. Special glue for vinyl canvases can be easily diluted in water without forming lumps. The finished glue can be stored for over 10 days. It is produced in the form of dry mixtures, the shelf life of which in a packaged state is from 3 years.

You should use wallpaper glue according to the instructions, trying to apply the composition onto the strip as evenly as possible. The adhesive should be applied with clean and dry hands. When applying the adhesive composition to the strips with a roller, a sliding layer is created, allowing them to be glued without problems. Aligning and joining such canvases after they are applied to the wall is not difficult.

When the glue dries, it creates a transparent film, which is important because the glue will not be visible after wallpapering the walls. Sometimes vinyl adhesive is used to prime the surface, as it can provide perfect adhesion to the wall surface. This glue is safe for human health because it does not contain or emit harmful substances.

How to properly stick heavy vinyl wallpaper

At the very beginning, you should cut the roll into separate strips, leaving a margin of 5 cm or more. If there is a pattern, you need to cut the canvas, adjusting the stripes in accordance with it. Then the strips are laid out face down on a specially prepared clean place. They should be placed one on top of the other so that they can rest. After this, they need to be rolled into a roll with a pattern inside and left for a day. This is necessary so that the wallpaper does not curl when applying the glue with a clean roller.

Not only embossing, but also various decorative elements can be applied to vinyl wallpaper.

If the roller is completely new, then clumps of fur may come off it. It is better to use a used roller. To apply glue to the canvas, prepare plastic film having a suitable length and width. Glue is applied thin layer, and then the strips of wallpaper are folded in half so that the layer of glue is inside and can saturate 2 or 3 sheets at once.

The glue is applied as evenly as possible, otherwise the vinyl sheets will separate from the walls in places. When applying glue, it should be taken into account that for vinyl wallpaper it will take some time, indicated directly on the glue packaging, for them to be properly saturated with glue. After the required time for impregnation, you must immediately begin gluing the canvases to the wall. Usually a stepladder is used for this purpose. Remove excess glue from the wallpaper with a clean material.

Gluing begins from the corner of the room wall, which is located perpendicular to the window. Heavy vinyl wallpaper, unlike light ones, can be glued in the corners in solid strips, rather than cutting them, as is required for lightweight wallpaper. Lightweight vinyl wallpaper can tear when the heating is turned on, which can be the result of temperature changes.

The strips must be applied to the very top of the wall, then they are carefully straightened downwards, smoothing them with a roller. You can use a spatula or brush to force out excess air from under the sheets. Vinyl wallpaper practically does not stretch, unlike ordinary canvases. Therefore, even if you miss the smallest air bubble, it will not be so easy to remove it.

When gluing heavy vinyl wallpaper, pay special attention to each connection, then roll it with a clean roller. You should choose it depending on the texture of the wallpaper. For smooth, heavy vinyl wallpaper, a rubber roller is often used. After gluing each strip, you should immediately cut off exactly the top or bottom of the wallpaper near the ceiling or baseboard.

What problems can you encounter when gluing wallpaper joints?

It is better not to glue vinyl wallpaper in bedrooms because it does not allow air to pass through.

For quality connection vinyl wallpaper on the wall surface, it is necessary that the edges of the strips be thoroughly coated with glue. After joining according to the pattern or without it, all connections must be blotted with a dry sponge to remove the glue. You cannot rub the joints, otherwise they will become glossy and shiny in the light. In practice, the joints do not require maximum attention; this will make the entire surface look more natural.

For manufacturers of some types of vinyl wallpaper, it is very important that a special adhesive is used for gluing the joints. This type of glue is sold separately in PVC tubes with long narrow spouts. The mechanism for working with this type of glue is as follows.

After gluing the two adjacent sheets, take joint glue to inject it into the seam, and then roll it with a joint roller. The main thing is not to allow air bubbles to pass through when the wallpaper is glued to the surface of the wall, which sometimes appear the next day. To eliminate swelling, you should purchase a 5 cm cubic pharmaceutical syringe, where you add the glue composition to inject it into punctures with swollen places. The remaining glue must be pressed out by wiping it dry.

Pasting walls is not as difficult as it might seem at first glance; the main thing is to follow a number of rules so that the whole work is crowned with success. Here are some rules:

1. When gluing vinyl sheets in the corners of a room, experts do not recommend bending the strip to join the corner of the room, since the joint will be very noticeable. It is best to glue a single strip with an overlap of 3-5 cm.
2. near the doors it is possible, if you do not stick vinyl sheets on two openings at the same time. It is necessary to carry out gluing, observing one-sided order.
3. A plumb line used to level the canvas will help you correctly paste the walls near the windows. This is required in order to properly trim its protrusions and tuck them inside the window niche. Then the wallpaper is glued under the windowsill.
4. Behind the radiators, it is necessary to paste the wallpaper correctly, as recommended by experts, 20 cm inward; there is no need to glue the canvas further. If you really need to cover the entire wall behind the radiator, then cut the canvas into 10 cm strips and paste them, pressing them with a long-handled roller. It is best to paint the wall behind the radiator.
5. Wallpaper sheets near the baseboards and ceiling should be glued using a ruler, which is necessary for cutting at the edge. The ruler is a regular profile with a triangular shape. This tool will not become dull when cutting vinyl.
6. To cover the ceiling with vinyl wallpaper, you must make markings. Glue the canvas starting from the window and continuing to the center of the ceiling. All work must be done by two people. In this case, one should glue the canvas from the stepladder, and the other should support it with a mop, standing on the floor.
7. To properly cover the ceiling with vinyl wallpaper, you need to make a preliminary marking, and the back side of the border should be moistened with water and left wet for 5 minutes. Then you need to apply the adhesive composition to the prepared border, which should be fixed in the required place. If the surface of the wallpaper is embossed, the border is installed before the vinyl wallpaper is applied. Next, the wallpaper strips are adjusted in accordance with the borders. The edges of the strips are trimmed with a ruler for wallpapering. For gluing, use special border glue.
8. When wallpapering walls next to electrical sockets or switches need to be de-energized. In places where there is a socket or switch, the glued sheets are cut crosswise. The resulting corners should be bent inside the socket, and then the switch and socket should be installed in their original places.