Any door handle has its own lifespan and is subjected to significant loads every day. Therefore, sooner or later, the question arises of replacing the old pen directly with a new one. Basically, all door fittings are installed by employees of the manufacturing company where the doors were purchased.

But when the handle fails, in most cases you will have to disassemble it yourself at home. Precisely, in such cases, you will need certain knowledge and information about the process of disassembling any door handle.

So, from the beginning it is imperative to determine what type the broken handle is, because the process of disassembling it depends on this. In the modern world, there is a huge selection of door handles with very diverse designs and shapes. But, in general, they can be divided into several main types.

Lever handles

Lever handles are typically installed on both interior and exterior doors. They are characterized by a door latch, which goes inside the door leaf when you press the handle. In the normal position, the metal latch tongue is extended.

Such handles are mainly found on doors that are equipped with mortise locks. The linings for such handles also come in two types: braided (solid) or separate (sold together with the lock included). When disassembling them, you need to remember the place where the latch was located.

Handles - knobs

In most cases, lever handles are designed to be installed on interior doors. Visually, pens of this type resemble a ball shape (but there are other shapes). The keyhole is located in the center of the door hardware. It is opened with a key only on one side, and on the other there is a button - a lock.

Stationary handles

Stationary handles are available in the form of strips, brackets, round, U-shaped, curly, etc. They are attached directly to the door leaf using screws. Even when purchasing this handle, the kit may include a roller latch, which will secure the door well when closed and open easily when the door is opened.

Now that the type of handle has been determined (it is regular or has a snap mechanism), you can directly begin the process of disassembling it.

1. In the case when the handle was screwed with self-tapping screws, then use a screwdriver to unscrew the main part. Once unscrewed, it is inspected for damage. If repair is impossible, then it is better to purchase exactly the same one instead.

You just need to make sure that the door trim matches the previous type, because at the attachment point there are already previously made holes for screws, which will be very difficult to hide if they do not match the new door trim. Therefore, it is recommended that you first dismantle the old handle and run with it to the nearest hardware store to buy a new one.

2. This type of handle may also have a common rod; you can verify this in the following way: you need to hold the door handle on one side and turn it counterclockwise on the other. The handle is rod-shaped, in the case when it is unscrewed. If this is the case, then the element is unscrewed on one side and the structure is removed from the reverse side, then a similar version of the new door hardware is selected. You can replace the old handle, for example, with a version with a latch, only the space from the rod needs to be covered with a new cover.

3. Handles that have mechanical latches are removed as follows: using a screwdriver, you need to carefully unscrew the screws and at the same time remove the decorative trim that is located around the handle (again, be extremely careful so as not to break something or forget the place where how the removable part was located).

The main components of this type of handle are the tetrahedral linings and the latch tongue mechanism. When the fittings are removed, you can see what the handle is supported on: it happens that a hole is made in the tetrahedral rod, and exactly the same in the handle, then a small rod with a cap is threaded through them. In such cases, the rod is simply removed and the handle is quite easily and simply removed. On the reverse side, you first need to unscrew the lining and remove the handle with the tetrahedral rod.

How to disassemble a round door handle

When disassembling a knob handle (or a round door handle), you must adhere to some rules, and this process will be absolutely easy, without any possible difficulties. Typically, this task requires a Phillips or flathead screwdriver, depending on the type of fastener. You will also need a key with a stop, which is provided with the handle when purchasing it. So, we’ll look at how to disassemble a round door handle below.

1. First, you need to use a flat screwdriver to pry and remove the flat trim, which is located around the door handle. Next, take a special key or any sharp and thin object that can be found at home, use it to press the open stopper, and pull the handle. Then it is carefully removed and several screws are unscrewed from the side where the handle was removed. Now both parts of the handle are removed from the door leaf and only after this can you unscrew the screws that hold the latch in place.

2. There are also cases when there is no need to change the door handle, but you just need to unfold it and then install it in the reverse order. To complete this task, first you need to insert the latch into the door leaf towards the closed door with the beveled side of the tongue and screw this element using two screws.

Next, the part of the handle on which the key mechanism is located is inserted into the desired side of the door. Then the clamping part is inserted from the opposite side and secured with two screws. At the end of the work done at home, be sure to check how the handle turns and whether it easily returns to its original position. If some difficulties arise, the handle needs to be aligned as necessary.

3. Next, the decorative strip is put on and the remaining part is installed in the clamping part. As a rule, a square rod with a metal flat plate must fit straight into the handle; to do this, you need to turn the lock on the handle so that the slot coincides with the same position of the square rod.

4. The final stage is as follows: you need to put on the handle and when it reaches the stopper, retract it, press the clamping part across the axis. Next, the removable part of the handle is pushed in all the way, reaching the clamping structure. The decorative strip is aligned along the groove, and eventually is completely put on. Well, of course, after these steps, the handle is checked for the quality of fixation and operation: you need to turn the handle several times until it stops on each side (that is, from the side of the drum latch mechanism itself, as well as from the latch side).

You can carefully remove and disassemble the door handle yourself without damaging the door leaf. Many people have experienced a faulty interior door handle. If it stops working, or problems arise that interfere with the comfortable and unhindered opening of the door, it is worth disassembling it and checking the reason. In the future, determine the cause of the breakdown and eliminate it. If the handle cannot be repaired, it should be replaced with a new one. In this case, you need to know how to disassemble the structure, assemble it or replace it, so as not to call a specialist for help.

Deciding on the look: how to disassemble a door handle

Handles are often exposed to people who live in an apartment or house. Therefore, pen breakage is no exception and can happen at any time. In order to find out why the handle broke, it is worth disassembling it and making sure what the reason is. Then repair it or replace it with a new one.

In order to disassemble an aluminum door handle, you need to know what type it is, since the mechanism depends on the model. After this, carefully remove it from the door.

Before you start disassembling the door handle, you need to decide on its type

The following types of handles exist:

• Push;
• Stationary;
• Rotary.

The push handle has the shape of the letter “G”. Its mechanism includes a tongue, with the help of which the opening process occurs.

The stationary handle is attached to the door leaf using screws/screws. It may have an axial element and be located on both sides of the door.

The rotary handle has the same mechanism as the push handle. When opening it you need to turn it. The model may have a round shape and look like a ball. To disassemble the handle, you need to remove it. To do this, you need to carefully separate it from the door leaf using a screwdriver.

Reasons for disassembly: how to remove the door handle of an interior door

Almost all pens have a similar disassembly process. If you know how to properly disassemble the handle, you can do it in half an hour. To do this, you need to understand how it works in order to unscrew it.

Reasons for disassembling a door handle:

• Failure – breakdown;
• Repair work;
• Replacing the old model;
• Loss of original aesthetic properties (scratches, abrasions).

If a cheap handle is installed, you should expect that it may break soon after installation. Door handles made in China have a short service life and are inexpensive. That's why many owners install such handles. But in order not to make repairs or replacements every time, it is worth choosing higher quality fittings for the interior door.

As a rule, door handles on interior doors are replaced if they break or lose their original properties.

During the renovation of an apartment, its interior can change dramatically. The old handle may not fit the updated version of the room/apartment. Therefore, you have to disassemble the previously installed handle and replace it with a new one.

New pen models are appearing on the market. They may have advantages over older models: updated and simplified mechanism, shape, color. Some people exchange old handles for new ones because they saw a product on sale that was better or of higher quality than what they had previously installed. This is also the reason for disassembling the handle.

If the handle has lost its original properties - appearance, then this is another reason to install new fittings. All door handles are subject to frequent exposure. Over time, scratches appear on them, and the decorative coating wears off. All these flaws spoil the appearance of the metal handle.

Repainting a handle is unprofitable, time consuming and not always possible. It's easier to replace it with a new one.

Step-by-step instructions: how to disassemble the round handle of an interior door

There is a certain scheme according to which round pens (knob pen or loku) are disassembled. To repair or replace it, you should carefully and carefully disassemble the handle structure. Disassembly will not take much time if you follow the instructions.

You can disassemble the round handle yourself if you carefully read the training instructions

Instructions for disassembling the round pen:

• Prepare the necessary tools for work (screwdriver, wrench with stop);
• Remove the trim around the handle;
• Press the open stop with a special key;
• Turn one handle (keep the other one stationary);
• Pull the handle on one side and remove;
• Unscrew the screws;
• Remove the handle on the other side;
• Unscrew the screws (they hold the latch);

Disassembly is done quickly using these instructions. The main thing is to carefully carry out all actions so as not to completely break the mechanism, because sometimes you can replace only one element and it will work.

How to replace a door handle with a lock: disassemble the push model

The push handle model is popular. It is installed not only on interior doors, but it is also suitable for entrance doors if it has a lock in its structure. In order to remove this handle, with a built-in latch or lock, you will need a little time and a screwdriver.

Before you start replacing a door handle with a lock, it is better to prepare the necessary tools in advance

Steps to remove the lever handle from the door:

• Unscrew the handle (its pressure part);
• Remove the trim;
• Unscrew the screws (which are hidden under the cover);
• Remove the first part of the handle (hold the other in a stationary position);
• Remove the second part of the handle together with the axial part.

If you need to disassemble the lock itself, then you need to unscrew the plate (from the end of the door). Then remove the mechanism itself.

In the case where the handle moves away from the door, it is not necessary to remove it completely. It is enough to tighten the bolts with which it is attached to the door.

To install the handle, you must first install the mechanism itself, then the handle and screw on the cover.

Sometimes the reason a pen doesn't work well is because it needs to be disassembled, cleaned of dust or lubricated. Or turn over the fittings if they have taken the wrong position over time.

How to disassemble a lock on an interior door (video)

The door handle is an integral part of the door design. Therefore it should work properly. It is not necessary to call a technician to replace or repair the door handle. It is enough to know a little about the mechanism of the handle that needs to be removed and take into account the instructions for disassembling it. In order for the door handle to work smoothly: it does not make sounds, it turns or presses well, the latch does not jam, you need to periodically lubricate its component parts of the mechanism and clean them from accumulated dust.

Have you ever wondered how many times a day you open and close the interior door in your apartment? Most likely no. Moreover, all our actions are performed here so mechanically that we do not pay any attention to such elements as ordinary door handles. Until something happens to them. As soon as some kind of breakdown occurs, we not only begin to pay attention to the fittings, but also understand how important the role they play in our home.

Unfortunately, no matter how high-quality and expensive door hardware is, it needs to be replaced from time to time. The reason for this can be either unexpected breakdowns or the usual desire to slightly update the door design. For dismantling work to be successful, it is important to know the basic rules for disassembling door handles, of which there are several types today.

How to easily remove and disassemble an interior door handle

A broken door handle and the desire to replace it with a new one are the most common reasons that force us to pick up a screwdriver and get to work. But before you do this, you need to carefully study the mechanism of this hardware.

Classification of door handles

All door handles that are installed in an interior door can be divided into three main types:

1. Stationary.
2. Push.
3. Knob handles.

Stationary are the simplest options for door handles. There are no built-in locks here, other than small latches or pinch rollers. To open the door with this handle, you just need to lightly pull it. They can have different shapes: U-shaped, round, etc.

How to remove a stationary handle from a door surface

Such handles practically do not break, so they are most often removed in order to replace them with new, more modern models.

If the fittings are held on by regular screws, you can disassemble them using a simple screwdriver.

If no screws are visible, most likely the common rod serves as the base here. To remove such a handle, you need to hold one part of it with your hand and rotate the other counterclockwise.

If the handle has mechanical latches, it will take a little more effort to remove it. First, use a screwdriver to remove the screws, after which the upper decorative trim, which is located around the handle, is removed. Here, as a rule, there is a latch (tongue) and a tetrahedral rod. Once the top coating has been removed, you can lightly remove the rods and remove the handles.

Disassembling the push handle on an interior door

The most popular option for door fittings, which is used in houses and apartments. The mechanism consists of two L-shaped parts; they are also connected using a special rod. When you press the handle, the latch is hidden, thereby allowing you to open the door. A simple but quite reliable option.

It will take a little more time to disassemble the push handle than with a stationary one.

The first thing we do here is remove the screws that hold the trim. Next the pallet is removed. Next, you need to carefully examine the tetrahedral rod. There are models in which the fittings are equipped with an additional fixing rod with a cap. In this case, the rod can be removed quite easily, and the fittings can simply be carefully unscrewed. The other part of the handle is removed along with the axial rod. Before doing this, do not forget to remove the cover.

An easy way to remove and disassemble the knob handle

Such handles are often installed in hotels, because in addition to their functionality, they also attract users with their attractive appearance. Translated from English, “knob” means handle, button. Its shape is round. It is very convenient to use, as it allows you to lock it with a key from the inside of the room. The only disadvantage of this fitting is that it breaks quite often, as a result of which you have to constantly disassemble it.

Before removing this mechanism, it must be thoroughly inspected. Here, as a rule, there is a locking pin on the side of the room, which allows you to secure the handle to the canvas. To make the fittings easier to use, the pin is specially equipped with a small spring.

To remove the handle, you need to take a sharp, thin object (a screwdriver works well) and gently press it onto the pin. It happens that the handles have decorative overlays, then upon first inspection you will not be able to see the pin. To access it, you need to remove all unnecessary pads. Most often they are attached using ordinary screws that can be easily unscrewed. In some models, you can remove these decorative elements simply by prying them off with a screwdriver.

Disassembling the knob handle

After the above steps have been completed, you can begin to disassemble the pen. This is done at the end of the door. Here you can immediately see the bar from which the latch comes out. There are two small screws at the top and bottom of this bar that can be removed using a regular Phillips screwdriver. There are some models where screws are installed with a regular straight cut, then you need to use the appropriate tool.

Once you have removed all the screws, you need to pry up the bar and carefully push out the inside of the latch. This concludes the analysis of the knob handle.

All work must be performed extremely carefully so as not to damage the surfaces of the doors, as well as to maintain the integrity of the handle itself (if you do not remove it to replace it with a new one). Removing and disassembling the door handle on an interior door is not at all difficult, the main thing is to follow all the recommendations and perform the necessary actions one by one.

Using door handles leads to wear and tear. Renovation required. You can call a professional or carry out the repairs yourself. Before doing the work, you need to study the materials in order to clearly understand how to disassemble the door handle at the door. There are different types of door handles: with and without a lock. Before starting repairs, it is necessary to establish the type of product in order to determine the sequence of actions.

The market has a large selection of handles for interior and exterior doors with and without a lock. All of them are classified into three types:

To disassemble and assemble door devices you will need the following tools:

• flat or Phillips screwdriver;
• a key with a stop, a sharp awl;
• pliers;
• Adjustable wrench.

Reasons for parsing

The technology of disassembling and assembling door mechanisms is not routine work. They are carried out if the fittings have become loose, the screws in the lock need to be tightened, repaired or replaced. Other reasons leading to the disassembly of fittings:

1. Product failure. The performance is impaired due to failure to prevent the mechanism or rough handling. This is one of the most common reasons for product failure.
2. Replacing the model. The production of models is constantly being improved, and there is a need to replace them.
3. Residential renovation. During a major renovation of a premises, the interior is updated. Old interior door handles may not fit into the new style, so they need to be replaced.
4. Surface wear. Scuffs, chips, and peeling paint appear on the product due to the poor quality of the coating. Therefore, the lock and fittings are disassembled and must be replaced.

Stages of disassembling fittings

The mechanism is disconnected from the door by removing the lining in the upper part located at the locking button. You can remove it using a key; if it is missing, use an awl. To do this, you need to press the stopper of the latch located in the fittings. The handle and axis of the clamp can be easily separated from the body by simply pulling it off. It is necessary to remove the parts and unscrew the screws with a screwdriver; the fittings move away from the door.

Disassembling a stationary handle

If the product is fixed with self-tapping screws, then it is enough to unscrew the screws with a flat screwdriver and remove the fittings. Inspect for damage. If it cannot be repaired, then it must be replaced.
When placing the product on a common rod, it is enough to remove the fastening fragment from one side. The structure must be removed from the reverse side. The presence of a rod in the product is checked by turning it counterclockwise while simultaneously holding it with your hand on the other side. If you can turn it, then it is on the rod.
The stationary handle with built-in latch can be removed with a screwdriver, unscrewing the screws and removing the decorative trim.

Disassembling the push handle

Unscrew the screws securing the cover and remove the tetrahedral rod. After this, the fittings can be easily removed. The second overlay is removed, the axial rod and the remaining part of the fittings are removed. The parts are inspected and a decision is made: replace or repair.

Disassembling the round pen

Knob fittings with a lock take longer to dismantle than other devices due to their complex structure. However, let's figure out how to disassemble a round door handle. To do this, you must follow the following steps:

• First, use a screwdriver to remove the flat cover located near the handle;
• press the stopper with a key or other sharp object and pull the product towards you;
• from the removal side, the screws are unscrewed, both parts move away from the door leaf;
• the screws securing the latch are unscrewed.

Handle assembly

To reassemble the handle, you need to perform all the steps in reverse order.

When moving the round handle, you need to insert a latch into the door. It should be adjacent to the closed surface of the door with the oblique part of the tongue.

After installing the products, they are fixed with screws. The key mechanism is mounted on the selected side of the door.

The pressure link is located on the other side and is secured with two screws. Upon completion of installation, the functionality of the product is checked. It should easily turn and return to its original location. The mechanism can be moved slightly to the side and aligned. To do this, its required position is fixed; a decorative strip is attached to the upper part.

The slot of the latch must be in the same position with the square-shaped plate rod, which must fit into the handle smoothly and without distortion.

Finally, the device is hung. It should be deepened inward by pressing against the axis of the clamping link of the fittings. The removable elements are inserted into the clamping part until it stops, and a decorative strip is hung. It remains to make sure that the mechanism is working properly.

The quality of fixation of the fittings is checked. It should turn freely and return to its original place. The check is performed by turning it until it stops both on the side of the latch and the drum latch mechanism.

A door handle can be called a key element for any interior door. Opening any door, be it folding, swinging or sliding, without such a simple device as a door handle is extremely inconvenient. That is why even accessories such as a latch or lock are much inferior to it in demand. In order to understand how to disassemble a door handle, you need to understand what they are. They are usually divided into two large groups: stationary and push-type

Stationary

A distinctive feature of stationary door handles is that they have no connection with the lock. They are usually installed separately, as an independent device. The only function of such a handle is to open and close the sash by holding it. They are usually attached almost anywhere with screws. The appearance of such handles is very diverse, but still, the most popular are the U-shaped ones, similar to a bracket, and they are usually fixed vertically. If it is necessary to restrict access to the room, you can install a roller latch from inside the room.

How to disassemble stationary handles

Usually, if a stationary door handle is installed, the question “how to disassemble the door handle of an interior door” does not cause difficulties. Since such devices are very simple, and breakdowns occur extremely rarely, they are removed only when there is a desire to change the model to a newer one. In order to do this, you just need to unscrew the screws with a flat-head screwdriver and remove the handle.

It also happens that the fittings are installed on a common axial rod. To make sure of this, you need to hold one of the handles tightly and try to turn the other. Then carefully unscrew one of the fragments, and the second one can then be removed from the door without much difficulty.

Push

The push handle mechanisms are a little more complicated. Because they have a halyard latch, they require a tight fit into the door. When pressed, the latch tongue is moved by the spring, as a result of which it becomes possible to open the door. In order for the sash to be easily slammed, the latch is extended when the handle is free. With this approach, sound and heat insulation becomes much higher, because the sash fits somewhat more tightly to the frame.

These mechanisms also have the possibility of emergency opening. In order to use it, you need to find a slot that is made on the front side. Then, using any flat object, such as a screwdriver, you can unlock the door without any problems.

How to disassemble a push-type door handle

It is worth noting that disassembling the push handle will take more time. In order to save it, you need to adhere to the following plan:

1. Use a screwdriver to remove the screws that hold the cover in place.
2. You need to pay attention to the design of the tetrahedral retaining rod. It is simply put away, and the fittings can be easily unscrewed.
3. Remove the second cover and remove the second fragment along with the axle rod.

Push mechanisms, in turn, are also divided into categories.

Mechanisms with a one-piece pallet cover, their installation occurs through a lock. The axial rod plays an irreplaceable role; the fittings are placed on it - it must clearly coincide with the thickness of the door leaf. You should immediately be prepared for the fact that if it breaks, replacing the entire mechanism is inevitable.

With separate pads. They can be either with or without a lock, the only thing that matters is the size of the key hole and the size of the linings themselves.

Nobs

If the time has come to decide how to disassemble a round door handle, then most likely you will have to deal with the handle - nob. This accessory is usually also classified as push-type, but they are no less common in the rotary category. Their mechanism of action is approximately the same, but in order for the shutter to open, you need to turn the nob. Often these handles have a locking button. When you press it, it will be difficult to open the door from the back side. Like the push handles, there is a slot on the front side for emergency opening.

Expert advice

Prev Next

To prevent oil paint from drying out during storage and to prevent a film from forming on it, place a circle of thick paper on the surface of the paint and fill it with a thin layer of drying oil.

"The polyethylene film covering the balcony or greenhouse is protected from being torn off by the wind by a string stretched on both sides at intervals of 10-15 cm."

"To make it easier to work with the concrete mixture, clay is usually added to it, but clay reduces the strength of the mixture. Add a spoonful of washing powder to it per bucket of water."

"To prevent the screw, the head of which is hidden behind the obstacle, from rotating along with the tightened nut, you need to throw several turns of thread or thin wire over it and lightly tighten the ends. Due to friction, the screw is held well in place. The ends of the thread can be cut off after tightening."

"You can cut out a birdhouse entrance without a brace. It is enough to split the front side of the board in the center and cut out half-holes of the required size with a chisel or hatchet, and then connect the halves again."

Wooden screw plugs crumble and fall out of the wall. Take your time to cut out the new plug. Fill the hole in the wall tightly with nylon from an old stocking. Using a nail of a suitable diameter heated red hot, melt a hole for the screw. The fused nylon will turn into a strong cork.

"It is not difficult to turn a carpenter's level into a theodolite by equipping it with an aiming device from a slot and a front sight."

"In order for two strips of linoleum to lie end to end, it is convenient to use a self-adhesive decorative film, placing it under the base of the noleum."

"To ensure that the nail goes in the right direction and does not bend when driven into a deep hole or groove, it should be placed inside the tube, secured with crumpled paper or plasticine."

Before drilling a hole in a concrete wall, secure a piece of paper just below it. Dust and concrete fragments will not fly around the room.

"To cut a pipe exactly at a right angle, we recommend doing this. Take an even strip of paper and screw it onto the pipe along the sawing line. The plane passing through the edge of the paper will be strictly perpendicular to the axis of the pipe."

"A simple device will help you move logs or wooden beams - a piece of motorcycle or bicycle chain, equipped with a hook on one side and attached to a crowbar on the other side."

"In order for one person to be able to work with a two-handed saw, we recommend using a simple technique: move the saw handle from the top to the bottom position."

You can cut a piece of slate of the required size with a saw, but it is better and easier to punch holes along the line of the intended cut with a nail at a frequency of 2-3 cm, and then break off the slate on the support.

"The best way to stick tiles to the wall: take bitumen, melt it and drop just four drops on the corners of the tile. It sticks dead in place."

When making shaped window casings, it is most convenient to cut shaped holes with a hacksaw with a sharpened blade.

"Making stained glass is a long and difficult task. You can make a quick imitation of stained glass. To do this, take thin slats or rods of vines, glue them to a sheet of glass, and then paint the glass and cover it with varnish."

"If you don't have a dowel at hand, you can make one from a piece of plastic tube. The body of a ballpoint pen can also be suitable for this. Having sawed off a piece of the required length, make a longitudinal cut, about halfway, and the dowel is ready."

"It is known how difficult it is to hang a door when working alone. But just shorten the bottom pin by 2-3 mm and the work will become much easier."

"A very durable, non-shrinking and fairly waterproof putty is made from bustylate mixed with any powder - chalk, gypsum, cement!, sawdust, etc."

"If you need to screw a screw into the end of a particle board, drill a hole slightly smaller than the diameter of the screw, fill the hole with Moment glue (not epoxy!), screw the screw in a day later. The board does not delaminate. However, the resulting connection can only be placed under load through day. "

"It is more convenient to secure portraits, photographs, paintings in wooden frames with glass not with nails, but with the help of pushpins bent at right angles. The pins are gently pressed with a screwdriver. Compared with nails, the danger of splitting thin frames is reduced to a minimum."

"It is not so easy to screw a screw into hard wood. If you poke a hole for the screw with an awl, and rub the screw itself generously with soap, then after such an operation the work will go like clockwork."

To save time, the edge of the wallpaper can be trimmed with a sharp knife without unrolling the roll. To do this, you must first align the end of the roll and draw the edge border on the outside with a simple pencil. Working with a knife, the roll must be gradually turned in the direction of rolling.

To carry large sheets of plywood, glass or thin iron at home, it is convenient to use a wire holder with three hooks at the bottom and a handle at the top.

IF you need to saw a round stick into the distance, this work is most conveniently done using a template. It is made of a metal tube with a groove in the middle. The diameter is chosen so that the template slides freely along the stick.

It will be better and easier to work with a hacksaw if in the middle part you increase the height of the teeth by 1/3.

If you attach a weight weighing about a kilogram to the front of the bow saw machine, the work will become easier. The load must be made removable so that the saw can be used to perform other work.

"A wax-like coating can be obtained by painting the surface with diluted PVA glue. To obtain the desired color, you need to dilute the glue with water tinted with watercolors."

"Making a cover for an ax blade is as easy as shelling pears. Take a piece of rubber tube, cut it lengthwise and put it on the blade. It is protected from slipping off by a ring cut from an old car camera."

"A linen cord will help you do without clamps when gluing wooden frames. You should put four short loops on the corners of the frame and two long ones to tighten the frames diagonally. The angles are adjusted using sticks that twist the middle loops."

"How to silence a creaking floorboard? Between the floorboards you need to drill a hole at an angle of 45° with a diameter of 6-8 mm, drive a wooden pin into it, lubricated with wood glue, cut off the protruding end with a chisel and putty on the floor surface."

"To make it easier to sand a floor covered with varnish or paint, iron it with an iron through a damp cloth - and the work will become easier."

"Slight rotting on wood can be eliminated as follows: the affected wood is removed from the healthy layer, and then soaked in a 10% formaldehyde solution. After drying, the area is puttied and painted over."

"Door hinges will not creak if they are lubricated in time - this is a long-known rule. But you can do without lubricant. To do this, you need to make a washer from polyethylene cork and put it on the hinge pin."